270 resultados para Plating.
Resumo:
The internal stresses in a duplex coating involving a prequenched layer are believed to change if it is exposed to thermal loading. To characterise the internal stresses in such a duplex coating, a gradient model of finite element method is set up. The initial stress within the substrate developed in as quenching and the internal stresses due to the tempering of the prequenched layer ( TPQL) in such a duplex coating are calculated. The synthetical internal stresses in coating can be estimated by superposing uniform initial stresses developed during plating. The results indicate that the residual tensile stresses due to fabrication in coating will be decreased greatly, or even synthetical compressive internal stresses may arise in the coating.
Resumo:
The interface of a laser-discrete-quenched steel substrate and as-deposited chromium electroplate was investigated by ion beam etching, dissolving-substrate-away and using a Vickers microhardness tester, in an attempt to reveal the mechanism that the service life of the chromium-coated parts is increased by the duplex technique of laser pre-quenching plus chromium post-depositing. The laser quenching of the steel substrate can reduce the steep hardness gradient at the substrate/chromium interface and improve the load-bearing capacity of chromium electroplate. Moreover, the laser quenching prior to plating has an extremely great effect on the morphologies and microstructure of the substrate/chromium interface: there is a transient interlayer at the original substrate/chromium interface while there is not at the laser-quenchedzone/chromium interface; the near-substrate surface microstructure and morphologies of the free-standing chromium electrodeposits, whose substrate was dissolved away with nital 30% in volume, inherit the periodically gradient characteristics of the laser-discrete-quenched substrate surface. (c) 2006 Elsevier B.V. All rights reserved.
Resumo:
为了测量强界面电镀铬层的界面韧性,利用连续CO_2激光器对钢基体上的电镀铬层表面进行循环扫描实验。结果表明:该种加热方式能够诱发铬层沿激光扫描方向呈周期性分布的屈曲变形。在此基础上,结合涂层屈曲变形理论,提出测量镀铬层界面韧性的激光屈曲法。该方法只需对一个屈曲单元的最大屈曲高度和屈曲半长进行测量,就可给出界面韧性。作为应用举例,利用该方法对上述镀铬层/钢基体结构界面韧性进行了测量。
Resumo:
用扫描电镜对比分析了电弧离子镀增加直线磁场过滤对沉积TiN和TiAlN薄膜中颗粒的密度和尺寸的影响,,结果表明,TIN薄膜中颗粒的最大直径,从14μm减小到3μm,颗粒密度从lO~9/cm~2。降低到10~5/cm~2.TilN薄膜由于靶材中含有低熔点金属Al,因而发射出更大的颗粒,有的颗粒集团达到20μm,磁场过滤后颗粒尺寸减小,颗粒密度降低到10~6/cm~2。分析了脉冲叠加直流偏压对TiCrZrN复合薄膜相组成的影响。颗粒可使电弧离子镀rriN/crN多层膜的结合力降低,并使针孔产生遗传。使用直线型磁场过滤及脉冲叠加直流偏压不仅使颗粒密度和尺寸显著降低和减小,而且多层化对小颗粒产生了包覆作用。
Resumo:
We describe the fabrication of a Mach-Zehnder optical modulator in LiNbO3 by femtosecond laser micormachining, which is composed of optical waveguides inscripted by a femtosecond laser and embedded microelectrodes subsequently using femtosecond laser ablation and selective electroless plating. A half-wave voltage close to 19 V is achieved at a wavelength of 632.8 nm with an interaction length of 2.6 mm. This simple and cost-effective technique opens up new opportunities for fabricating integrated electro-optic devices. (C) 2008 Optical Society of America
Resumo:
We present a novel technique to fabricate deeply embedded microelectrodes in LiNbO3 using femtosecond pulsed laser ablation and selective electroless plating. The fabrication process mainly consists of four steps, which are (1) micromachining of microgrooves on the surface of LiNbO3 by femtosecond laser ablation; (2) formation of AgNO3 films on substrates; (3) scanning the femtosecond laser beam in the fabricated microgrooves for modi. cation of the inner surfaces; and (4) electroless copper plating. The void-free electroless copper plating is obtained with appropriate cross section of microgrooves and uniform initiation of the autocatalytic deposition on the inner surface of grooves. The dimension and shape of the microelectrodes could be accurately controlled by changing the conditions of femtosecond laser ablation, which in turn can control the distribution of electric field inside LiNbO3 crystal for various applications, opening up a new approach to fabricate three-dimensional integrated electro-optic devices. (C) 2008 Elsevier B. V. All rights reserved.
Resumo:
We investigate the mechanism of selective metallization on glass surfaces with the assistance of femtosecond laser irradiation followed by electroless plating. Irradiation of femtosecond laser makes it possible to selectively deposit copper microstructures in the irradiated area on glass surfaces coated with silver nitrate films. The energy-dispersive X-ray (EDX) analyses reveal that silver atoms are produced on the surface of grooves formed by laser ablation, which serve as catalysis seeds for subsequent electroless copper plating. (C) 2008 Elsevier B.V. All rights reserved.
Resumo:
We report the fabrication of a novel surface-enhanced Raman scattering (SERS) substrate with a controllable enhancement factor (EF) using femtosecond laser direct writing on Ag+-doped phosphate glass followed by chemical plating at similar to 40 degrees C. Silver seeds were first photoreduced using a femtosecond laser in a laser-irradiated area and then transformed into silver nanoparticles of suitable size for SERS application in the subsequent chemical plating. Rhodamine 6G was used as a probing molecule to investigate the enhancement effect of a Raman signal on the substrate. Nearly homogenous enhancement of the Raman signal over the Substrate was achieved, and the EF of the substrate was controlled to some extent by adjusting fabrication parameters. Moreover, the ability of forming a SERS platform in an embedded microfluidic chamber would be of great use for establishing a compact lab-on-a-chip device based on Raman analysis.
Resumo:
We report selective metallization on surfaces of insulators ( glass slides and lithium niobate crystal) based on femtosecond laser modification combined with electroless plating. The process is mainly composed of four steps: (1) formation of silver nitrate thin films on the surfaces of glass or crystal substrates; (2) generation of silver particles in the irradiated area by femtosecond laser direct writing; (3) removal of unirradiated silver nitrate films; and (4) selective electroless plating in the modified area. We discuss the mechanism of selective metallization on the insulators. Moreover, we investigate the electrical and adhesive properties of the copper microstructures patterned on the insulator surfaces, showing great potential of integrating electrical functions into lab-on-a-chip devices. (C) 2007 Optical Society of America.
Resumo:
An experimental investigation was made of forced convection film boiling of subcooled water around a sphere at atmospheric pressure. The water was sufficiently cool that the vapor condensed before leaving the film with the result that no vapor bubbles left the film. The experimental runs were made using inductively heated spheres at temperatures above 740°C. and using inlet water temperatures between 15°C. and 27°C. The spheres used had diameters of 1/2 inch, 9/16 inch, and 3/8 inch and were supported by the liquid flow. Reynolds numbers between 60 and 700 were used.
Analysis of the collected non-condensables indicated that oxygen and nitrogen dissolved in the water accumulated within the vapor film and that hetrogeneous chemical reactions occurred at the sphere surface. An iron-steam reaction resulted in more than 20% by volume hydrogen in the film at wall temperatures above 900°C. At temperatures near 1100°C. more than 80% by volume of the film was composed of hydrogen. It was found that gold plating of the sphere could eliminate this reaction.
Material and energy balances were used to derive equations which may be used to predict the overall average heat transfer coefficients for subcooled film boiling around a sphere. These equations include the effect of dissolved gases in the water. Equations also were derived which may be used to predict the composition of the film for cases in which an equilibrium exists between the dissolved gases and the gases in the film.
The derived equations were compared to the experimental results. It was found that a correlation existed between the Nusselt number for heat transfer from the vapor-liquid interface into the liquid and the Reynolds number, liquid Prandtl number product. In addition, it was found that the percentage of dissolved oxygen removed during the film boiling could be predicted to within 10%.
Resumo:
Actinomycetes are a group of micro-organisms which lie, in classification, half-way between the fungi and the bacteria. They may be isolated from the plating of leaf washings, water samples and mud dilutions on to nutrient agar (with incorporated actidione to eliminate fungi). The predominant genus varied with the source of the sample. An attempt was also made to isolate the phages of some Actinomycetes. A search was made in the typical environments of the host, for the virus. In this way actinophage were also isolated; and shown to be capable of being transmitted from one host strain to another host strain within 1 sp or from one host to another within 1 genus; i.e. polyvalent.
Resumo:
A presente investigação teve como objetivo avaliar a prática de cirurgiões dentistas em uma unidade de terapia intensiva (UTI) de um hospital militar, o estabelecimento de um protocolo de higiene oral e os seus efeitos sobre a redução de pneumonias associadas à ventilação mecânica (PAVM). As percepções da equipe da UTI sobre as atividades dos cirurgiões dentistas também foram avaliadas por meio de um questionário. O perfil de colonização microbiana da mucosa oral antes e depois do estabelecimento das medidas de higiene oral também foi avaliado tanto por diluição e plaqueamento em meios de cultura microbiológicos seletivos e enriquecidos e através da amplificação pelo método de PCR e eletroforese em gel desnaturante em gradiente (DGGE), subsequente ao sequenciamento dos amplicons. A carga microbiana foi avaliada após a contagem de placas de agar e através da amplificação por PCR em tempo real (qPCR) do gene rrs nas amostras. O protocolo de higiene oral, realizado pelos cirurgiões dentistas, foi capaz de reduzir a incidência de PAVM (p <0,05). O questionário revelou que a modificação da halitose foi percebida por 93,33% dos participantes. A redução da ocorrência das úlceras orais e dos lábios durante a internação dos pacientes foi observada por 80% da equipe da UTI. Foi observada a redução da produção das secreções nasais e bucais por 70% da equipe dos profissionais da UTI. Para 86,66% dos participantes a assistência aos pacientes tornou-se mais agradável após a instituição dos cuidados bucais. O protocolo, realizado com a utilização de solução 0,12% de clorexidina, não foi capaz de evitar a colonização da mucosa oral por patógenos microbianos usualmente encontrados no ambiente hospitalar tais como os bastonetes Gram-negativos entéricos e não fermentadores, nem foi capaz de eliminá-los quando tais micro-organismos já se encontravam presentes antes dos procedimentos de higiene bucal. Alguns Bastonetes Gram-positivos (Lactobacillus sp e corinebactérias) e Staphylococcus epidermidis permaneceram após a realização dos procedimentos. O protocolo de higiene oral permitiu a redução da carga microbiana na mucosa oral de 50% dos pacientes considerando-se o método de contagem microbiana e para 35% dos pacientes pela avaliação dos números de cópias de genes rrs através de qPCR. Em conclusão, o protocolo de higiene oral desenvolvido pelos cirurgiões dentistas foi capaz de reduzir a incidência de PAV na UTI, embora não tenha sido capaz de prevenir a colonização da mucosa oral por supostos patógenos microbianos. O protocolo de higiene oral com a participação ativa dos cirurgiões dentistas foi bem aceito pelos profissionais da UTI e foi capaz de melhorar a qualidade da assistência aos pacientes críticos.
Resumo:
Three enrichment broths and six plating media were compared for efficiency of detection Salmonella in the presence of numbers of Coliforms (10super(5)/ml) and proteus (10super(3)/ml) from artificially inoculated fish samples. Recovery experiments Salmonella anatum, S. typhimurium and S. enteritidis indicated that the two enrichment broths Dulcitol Selinite (DSE) and Selinite Cystine (SC) were equally efficient. Further, the viability of Salmonella, inoculated into fish muscle and kept at 4°C for 48 hours, was found to be not affected by the low temperature storage. Selective plating media like Xylose Lysine Deoxycholate agar (XLD), Brilliant Green Sulphadiazine agar (BGS) and Brilliant Green agar (BG) were found to be superior in performance to Salmonella-Shigella agar: (SS) and Bismuth Sui phite agar (BiS).
Resumo:
Prawn processing factories of the three major fish processing centres of the West Coast of India, viz., Cochin, Mangalore and Calicut were surveyed to determine the occurrence of Clostridium perfringens in processing areas, and in processed products. Direct plating on Sulphite-polymyxin- sulphadiazine Agar and enrichment techniques were used. Samples of prawn, prawn guts, frozen prawns, canned prawns, water, ice, swab from utensils and soil from the factory premises were examined. Among a total of 461 samples examined, only 32 (6.9%) gave positive results. The incidence of C. perfringens was more in prawn guts (80%), followed by soil (50%), prawn (38%), ice (33.3%), frozen prawns (11%), swab (5.0%) and water (1.1%). No C. perfringens was isolated from canned prawns.
Resumo:
Three direct plating methods and two most probable number (MPN) procedures were compared for the enumeration of Clostridium perfringens in seafoods the sulfitecycloserine (SC) agar, sulfite-polymyxin-sulfadiazine (SPS) agar, tryptone-sulfite- neomycin (TSN) agar, LS medium MPN procedure and iron milk MPN procedure. Isolates were confirmed as C. perfringens. The two MPN procedures compared very well with the three plating media tested with stock culture of C. perfringens from our laboratory collection and the reference strain NCIB 6125. But in fish samples, the two liquid media were found to be more sensitive and hence the MPN procedure using LS medium for the detection of C. perfringens in seafoods is suggested.