Enhancement of ion dissociation in polyelectrolyte gels

High conductivity in single ion conducting polymer electrolytes is still the ultimate aim for many electrochemical devices such as secondary lithium batteries. Achieving effective ion dissociation in these cases remains a challenge since the active ion tends to remain in close proximity to the backbone charge as a result of a low degree of ion dissociation. A unique aspect of this dissociation problem in polyelectrolytes is the repulsion between the backbone charges created by dissociation. One way of enhancing ion dissociation in polyelectrolyte systems is to use copolymers in which only a fraction (<20%) of the mer units are charged and where the comonomer is itself chosen to be polar and preferably to be compatible with potential solvents. We have also found that certain dissociation enhancers based on ionic liquids or boroxine ring compounds can lead to high ionic conductivity. In the cases where an ionic liquid is used as the solvent in a polyelectrolyte gel, the viscosity of the ionic liquid and its hydrophilicity are critical to achieving high conductivity. Compounds based on the dicyanamide anion appear to be very effective ionic solvents; polyelectrolyte gels incorporating such ionic liquids exhibit conductivities as high as 10⁻² S/cm at room temperature. In the case of boroxine ring dissociation enhancers, gels based on poly(lithium-2-acrylamido-2-methyl-1-propanesulfonate) and ethylene carbonate produce conductivities approaching 10⁻³ S/cm. This paper will discuss these approaches for achieving higher conductivity in polyelectrolyte materials and suggest future directions to ensure single ion transport.

Zwitterion effect in polyelectrolyte gels based on lithium methacrylate-N,N-dimethyl acrylamide copolymer

Zwitterionic compounds such as those based on 1-butylimidazolium-3-(n-butanesulfonate) have previously been shown to have positive effects on the transport properties of polyelectrolytes. The addition of the zwitterion has been found to, in some cases, increase the dissociation of the lithium ion and enhance the conductivity by almost an order of magnitude. In this work, we report the effects of adding the above-mentioned zwitterion into the polyelectrolyte gel system poly(lithium methacrylate-co-N,N-dimethyl acrylamide); the anionic group being a stronger base leads to different behaviour for this copolymer compared to previous work. Polyelectrolyte gels based on dimethyl sulfoxide and polyether solvents were investigated to determine the breadth of applicability of the zwitterion in improving lithium ion transport. Impedance spectroscopy and pulse field gradient-NMR diffusion indicate an increase in the number of available charge carriers with zwitterion addition in some gel systems, however, the effect is not universal.

Polyelectrolyte-in-ionic-liquid electrolytes

Novel polymer electrolyte materials based on a polyelectrolyte-in-ionic-liquid principle are described. A combination of a lithium 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPSLi) and N,N′-dimethylacrylamide (DMMA) are miscible with the ionic liquid, 1-ethyl-3-methylimidazolium dicyanamide (EMIDCA). EMIDCA has remarkably high conductivity (≥ 2 · 10−2 S · cm−1) at room temperature and acts as a good solvating medium for the polyelectrolyte. At compositions of AMPSLi less than or equal to 75 mol-% in the copolymer (P(AMPSLi-co-DMAA)), the polyelectrolytes in EMIDCA are homogeneous, flexible elastomeric gel materials at 10 − 15 wt.-% of total polyelectrolyte. Conductivities higher than 8 · 10−3 S · cm−1 at 30 °C have been achieved. The effects of the monomer composition, polyelectrolyte concentration, temperature and lithium concentration on the ionic conductivity have been studied using thermal and conductivity analysis, and pulsed field gradient nuclear magnetic resonance techniques.

Deposition and wetting characteristics of polyelectrolyte multilayers on plasma-modified porous polyethylene

Hydrophilic and chemically reactive porous media were prepared by adsorbing functional polymers at the surface of sintered polyethylene membranes. Modification of the membrane was accomplished by first exposing the membrane to an oxygen glow discharge gas plasma to introduce an electrostatic charge at the membrane surfaces. Cationic polyelectrolyte polyethylenimine (PEI) was adsorbed from solution to the anionic-charged surface to form an adsorbed monolayer. The adsorption of a second anionic polyelectrolyte onto the PEI layer allows further modification of the membrane surface to form a polyelectrolyte-bilayer complex. The conformation and stability of the adsorbed monolayers and bilayers comprising the modified surface are probed as a function of the polymer structure, charge density, and solubility. Using X-ray photoelectron spectroscopy analysis, we demonstrate that the presence of the polyelectrolyte multilayers drastically increases the density and specificity of the functional groups at the surface, more than what can be achieved through the plasma modification alone. Also, using the wicking rate of deionized, distilled water through the porous membrane to gauge the interfacial energy of the modified surface, we show that the membrane wicking rate can be controlled by varying the chemistry of the adsorbing polyelectrolytes and, to a lesser extent, by adjusting the polarity or ionic strength of the polyelectrolyte solution.

One-dimensional polyelectrolyte/polymeric semiconductor core/shell structure : sulfonated poly(arylene ether ketone)/polyaniline nanofibers for organic field-effect transistors

A polyelectrolyte/polymeric semiconductor core/shell structure is developed for organic field-effect transistors (OFETs) based on sulfonated poly(arylene ether ketone)/polyaniline core/shell nanofibers via electrospinning and solution-phase selective polymerization. The polyelectrolyte does not work as a gate dielectric, but can provide an internal modulation from the nanointerface of the 1D core/shell nanostructure. The transistor devices display very high mobilities.

Nanofibrillar micelles and entrapped vesicles from biodegradable block copolymer/polyelectrolyte complexes in aqueous media

Here we report a viable route to fibrillar micelles and entrapped vesicles in aqueous solutions. Nanofibrillar micelles and entrapped vesicles were prepared from complexes of a biodegradable block copolymer poly(ethylene oxide)-block-poly(lactide) (PEO-b-PLA) and a polyelectrolyte poly(acrylic acid) (PAA) in aqueous media and directly visualized using cryogenic transmission electron microscopy (cryo-TEM). The self-assembly and the morphological changes in the complexes were induced by the addition of PAA/water solution into the PEO-b-PLA in tetrahydrofuran followed by dialysis against water. A variety of morphologies including spherical wormlike and fibrillar micelles, and both unilamellar and entrapped vesicles, were observed, depending on the composition, complementary binding sites of PAA and PEO, and the change in the interfacial energy. Increasing the water content in each [AA]/[EO] ratio led to a morphological transition from spheres to vesicles, displaying both the composition- and dilution-dependent micellar-to-vesicular morphological transitions.

Mechanical Reinforcement of Continuous Flow Spun Polyelectrolyte Complex Fibers

A simple continuous flow wet-spinning method to achieve mechanical reinforcement of the two oppositely charged biopolymers chitosan and gellan gum is described. The mechanical properties of these biopolymers are influenced by the order of addition. Using a facile method for mechanical reinforcement of gellan gum/chitosan fibers resulted in increases in Young's modulus, tensile strength, and toughness. Spinning gellan gum into chitosan resulted in the strongest fibers. We show that our fibers can provide a mechanical alternative for bio-fibers without the need of cross-linking. It is demonstrated that the fibers become ionically conducting in the presence of water vapor.

Spinning Carbon Nanotube-Gel Fibers Using Polyelectrolyte Complexation

Biopolymer-single walled carbon nanotube (SWNT)-biopolymer fibers were prepared using a continuous flow spinning approach. Polyelectrolyte complexation was facilitated by injecting a SWNT-biopolymer dispersion into a coagulation bath containing a biopolymer of opposite charge. We showed that the ability to spin fibers and their properties depend on processing conditions such as polyelectrolyte pH, sonolysis regime (conditions employed to disperse SWNT) and the order of adding the anionic and cationic biopolymer solutions. Maximizing the ionic nature through changes in the pH increased spin-ability, while combining a sonicated dispersion with an as-prepared (non-sonicated) polyelectrolyte solution allowed us to optimize sonolysis conditions while retaining spin-ability of fibers with smooth surface morphology. Addition of the cationic biopolymer-SWNT dispersion to the anionic biopolymer solution resulted in mechanical reinforcement with the increase in SWNT loading fraction. All fibers decreased their electrical resistance upon exposure to water vapor.

Encapsulation of single hMSCs in polyelectrolyte shells

The main objective of this Thesis was to encapsulate single viable cells within polyelectrolyte films using the Layer-by-Layer (LbL) technique. Most of the experiments used human mesenchymal stem cells (MSCs) whose characteristics (capacity of selfrenewal and potential to differentiate into several types of cells) make them particularly interesting to be used in biomedical applications. Also, most of the experiments used alginate (ALG) as the anionic polyelectrolyte and chitosan (CHI) or poly(allylamine hydrochloride) (PAH) as the cationic polyelectrolyte. Hyaluronic acid (HA) was also tested as an anionic polyelectrolyte. At the beginning of the work, the experimental conditions necessary to obtain the encapsulation of individual cells were studied and established. Through fluorescence microscopy visualization by staining the cell nucleus and using polyelectrolytes conjugated to fluorescent dyes, it was possible to prove the obtainment of capsules containing one single cell inside. Capsules aggregation was an observed problem which, despite the efforts to design an experimental process to avoid this situation (namely, by playing with cell concentration and different means of re-suspending and stirring the cells), was not completely overcome. In a second part of the project, single cells were encapsulated within polyelectrolyte layers made of CHI/ALG, PAH/ALG and PAH/HA and their viability was evaluated through the resazurin reduction assay and the Live/Dead assay. In these experiments, during the LbL process, polyelectrolyte solutions were used at a concentration of 1mg/mL based on literature. In general, the viability of the encapsulated cells was shown to be very low/absent. Then, as a consequence of the lack of viability of cells encapsulated within polyelectrolyte layers, the LbL technique was applied in cells growing adherent to the surface of cell culture plates. The cells were cultured like in a sandwich, between the surface of the cell culture dish and the polyelectrolyte layers. Also here, the polyelectrolyte solutions were used at a concentration of 1mg/mL during the LbL process. Surprisingly, cell viability was also absent in these systems. A systematic study (dose-effect study) was performed to evaluate the effect of the concentration of the individual polyelectrolytes (ALG, CHI and PAH were studied) in cell viability. Experiments were performed using cells growing adherent to the surface of cell culture plates. The results pointed out that a very high (cytotoxic) concentration of polyelectrolytes had been in use. Also, in general, PAH was much more cytotoxic than CHI, whereas ALG was the less cytotoxic polyelectrolyte. Finally, using alginate and chitosan solutions with adequate concentrations (low concentrations: 50ng/mL and 1μg/mL), the encapsulation of single viable cells was again attempted. Once again, the encapsulated cells were not shown to be viable. In conclusion, the viability of the encapsulated cells is not only dependent on the cytotoxic characteristics (or combined cytotoxic characteristics) of the polyelectrolytes but it seems that, when detached from the culture plates, the cells become too fragile and lose their viability very easily.

Nanoscale manipulation of CdSe quantum dots in layer-by-layer films: influence of the host polyelectrolyte on the luminescent properties

Thioglycolic acid-capped Use quantum dots (QDs) were assembled on glass substrates with two distinct polyelectrolytes, viz poly(allylamine hydrochloride) (PAH) and poly(amidoamine) (PAMAM), generation 4 dendrimer, via the layer-by-layer (LbL) technique. Films containing up to 30 polyelectrolyte/QD bilayers were prepared. The growth of the multilayers was monitored with UV-vis spectroscopy, which showed an almost linear increase in the absorbance of the 2.8 nm QDs at 535 nm with the number of deposited bilayers. AFM measurements estimated a film thickness of 3 nm per bilayer for the PAH/Cdse films. The adsorption process and the optical properties of the PAMAM/CdSe LbL films were further analyzed layer-by-layer using surface plasmon resonance (SPR), from which a thickness of 3.2 nm was found for a PAMAM/CdSe bilayer. Photoluminescence measurements revealed higher photooxidation of the quantum dots in PAH/CdSe than in PAMAM/CdSe films. (c) 2004 Elsevier B.V. All rights reserved.