Grain size analysis on core plugs of sediment core CRP-1 (Table 1, 2)

Twenty four core samples from CRP-1, seven from Quaternary strata (20-43.55 meters below sea floor or mbsf) and seventeen from early Miocene strata (43.55 to 147.69 mbsf), have been analysed for their grain-size distribution using standard sieve and Sedigraph techniques. The results are in good agreement with estimates of texture made as part of the visual core description for the 1 :20 core logs for CRP-1 (Cape Roberts Science Team, 1998). Interpretation of the analyses presented here takes into account the likely setting of the site in Quaternary times as it is today, with CRP-1 high on the landward flank of a well-defined submarine ridge rising several hundred metres above basins on either side. In contrast, seismic geometries for strata deposited in early Miocene times indicate a generally planar sea floor dipping gently seaward. Fossils from these strata indicate shallow water depths (< 100 m), indicating the possibility that waves and tidal currents may have influenced sea floor sediments. The sediments analysed here are considered in terms of 3 textural facies: diamict, mud (silt and clay) and sand. Most of the Quaternary section but only 30% of the early Miocene section is diamict, a poorly sorted mixture of sand and mud with scattered clasts, indicating little wave or current influence on its texture. Although not definitive, diamict textures and other features suggest that the sediment originated as basal glacial debris but has been subsequently modified by minor winnowing, consistent with the field interpretation of this facies as ice-proximal and distal glaciomarine sediment. Sediments deposited directly from glacier ice appear to be lacking. Mud facies sediments, which comprise only 10% of the Quaternary section but a third of the early Miocene section, were deposited below wave base and largely from suspension, and show features (described elsewhere in this volume) indicative of the influence of both glacial and sediment gravity flow processes. Sand facies sediments have a considerable proportion of mud, normally more than 20%, but a well-sorted fine-very fine sand fraction. In the context of the early Miocene coastal setting we interpret these sediments as shoreface sands close to wave base.

Community water supply well shooting/blasting near Hillcrest Subdivision, Lake County, Illinois.

The purpose of this fact sheet is to provide a summary of literature research on the use of well "shooting" or blasting technology in Northern Illinois. Water well shooting or blasting is done to increase water yield from a sandstone aquifer for a particular water supply well ... The Lake County Health Department (LCHD) detected a chemical, vinyl chloride -- from a family of chemicals known as volatile organic compounds (VOCs) -- in some private wells in the unincorporated Hillcrest Subdivision near Wauconda, through routine well testing done in the fall of 2003. The LCHD presented these findings to the public at a January 13, 2004 meeting. The concern was raised at the public meeting that recent subsurface water well "shooting" or blasting techniques, performed in the deep sandstone aquifer (800 to 1,000 feet below ground surface), in the borehole of a community water supply (CWS) well in the area, might have impacted the shallow aquifer in such a way as to contribute to private well contamination under investigation in the Hillcrest Subdivision.

The fundamentals of well log interpretation.

Previous editions published under title: The fundamentals of electric log interpretation.

The oil shock of 2005

During the course of 2005, the price of crude oil reached unprecedented high levels, at least in nominal terms. Australian motorists have become used to paying more than a dollar a litre for petrol. Given the past volatility in oil prices, often described in terms of a series of oil ‘shocks’ (the large price increases in 1973, 1979 and 1999), several questions arise. First, will current high prices persist, or will prices decline substantially as occurred after previous oil shocks? Second, is the current shortage of oil a temporary phenomenon, caused by inadequate investment in oil exploration, drilling and refining capacity, or is it a signal that the supply of oil available to the world has peaked? Third, will high oil prices lead to broader economic disruption, as is commonly supposed to have happened after previous shocks? Fourth, how painful will an adjustment to lower use of oil be? Finally, how does all this relate to our efforts to deal with the problem of climate change? This article is an effort to answer some of these questions in the light of the knowledge available to us.

Formulação de pastas cimentícias com adição de suspensões de quitosana para cimentação de poços de petróleo

Primary cementing is one of the main operations in well drilling responsible for the mechanical stability and zonal isolation during the production of oil. However, the cement sheath is constantly under mechanical stresses and temperature variations caused by the recovery of heavy oil. In order to minimize fracture and wear of the cement sheath, new admixtures are developed to improve the properties of Portland cement slurries and avoid environmental contamination caused by leaking gas and oil. Polymers with the ability to form polymeric films are candidates to improve the properties of hardened cement slurries, especially their fracture energy. The present study aimed at evaluating the effect of the addition of a chitosan suspension on cement slurries in order to improve the properties of the cement and increase its performance on heavy oil recovery. Chitosan was dissolved in acetic ac id (0.25 M and 2 M) and added to the formulation of the slurries in different concentrations. SEM analyses confirmed the formation of polymeric films in the cementitious matrix. Strength tests showed higher fracture energy compared to slurries without the addition of chitosan. The formation of the polymeric films also reduced the permeability of the slurry. Therefore, chitosan suspensions can be potentially used as cementing admixtures for heavy oil well applications

influência da adição de diferentes sais em pastas de cimento portland para cimentação de poços de petróleo

One of the great challenges at present time related with the materials area concerns of products and processes for use in petroleum industry, more precisely related to the Pre-salt area. Progresses were reached in the last years allowing the drilling of the salt layer, with the time reduction for drilling and larger success at the end. For the oil wells companies the preponderant factor is the technology, however, in spite of the progress, a series of challenges is still susceptible to solutions and one of them refers to the slurries preparation for cementing in those areas. Inside of this context, this study had for objective to analyze the influence of the salts NaCl, KCl, CaSO4 and MgSO4 in strength and chemical structure of the hydrated products. As methodology, they were prepared and analyzed cement slurries with varied concentrations of these salts that are commonly found in the saline formations. The salts concentrations used in formulations of the slurries were of 5%, 15% and 30%. The slurries were formulated with specific weight of 15,8 lb / gal and the cement used was Class G. Strength tests were accomplished in samples cured by 24 hours and 28 days. Also were realized crystallographic characterization (XRD) and morphologic (SEM). In agreement with the presented results, it is observed that the largest resistance values are attributed to the slurries with concentration of 15%. There was reduction of the strength values of the slurries formulated with concentration of 30%. Through the characterization microstructural it was possible to note the salts influence in the main cement hydrated products

Avaliação da adição de Nanosílica e silicato de sódio em pastas de cimento para poços de petróleo com baixo gradiente de fratura

The oil wells cementing is a critical step during the phase of well drilling, because problems during the operation of slurry pumping and an incomplete filling of the annular space between the metal casing and the formation can cause the slurry loss. Therefore, the slurry adopted in primary cementing an oil well must be properly dosed so that these problems are avoided during its pumping. When you drill a well in a weak rock formation requires even more careful, because should be a limit of hydrostatic pressure exerted during cementation, that does not occur rock collapse. With the objective of performing the cementing of a well whose formation is weak or unconsolidated are employed lighter slurries. Thus, this study used slurries with sodium silicate and nano silica in concentrations of 0,1; 0,4; 0,7 e 1,0 gpc, in which the slurries with nano silica showed the rheological parameters higher concentrations of up to 0.7 gpc and for concentration of 1.0 the slurry with sodium silicate obtained the highest values, remaining above the limits for application in fields, mainly wells with low fracture gradient, because a significant increase in viscosity may result in an increase in pressure pumping in operations of secondary cementations. Furthermore, there was no decrease in strength with increasing concentration of additive. Then, it is possible use of these additives to formulate Lighter slurry

Avaliação do comportamento reológico de pastas de cimento para poços de petróleo com adição de plastificantes

The isolation of adjacent zones encountered during oilwell drilling is carried out by Portland-based cement slurries. The slurries are pumped into the annular positions between the well and the casing. Their rheological behavior is a very important component for the cementing process. Nowadays, several alternative materials are used in oilwell cementing, with goal the modification and the improvement of their properties, mainly the increase of the fluidity. And this can be reached by using plasticizers additives able to account for different oilwell conditions, yielding compatible cement slurries and allowing enough time for the complete cementing operation. If the rheological properties of the slurry are properly characterized, the load loss and flow regime can be correctly predicted. However, this experimental characterization is difficult. Rheological models capable of describing the cement slurry behavior must be capable of predicting the slurry cement deformation within reasonable accuracy. The aim of this study was to characterize rheologically the slurries prepared with a especial class of Portland cement, water and plasticizers based on lignosulfonate, melamine and polycarboxylate at temperatures varying from 27°C to 72°C. The tests were carried out according to the practical recommendations of the API RP 10B guidelines. The results revealed a great efficiency and the dispersive power of the polycarboxylate, for all temperatures tested. This additive promoted high fluidity of the slurries, with no sedimentation. High lignosulfonate and melamine concentrations did not reduce the rheological parameters (plastic viscosity and yield stress) of the slurries. It was verified that these additives were not compatible with the type of cement used. The evaluated rheological models were capable of describing the behavior of the slurries only within concentration and temperature ranges specific for each type of additive

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

ESEM study of authigenic chlorite acid sensitivity in sandstone reservoirs

The effect of HCl on authigenic chlorite in three different sandstones has been examined uisng an Environmental Scanning Electron Microscope (ESEM), together with conventional analytical techniques. The ESEM enabled chlorites to be directly observed in situ at high magnifications during HCl treatment, and was particularly effective in allowing the same chlorite areas to be closely compared before and after acid treatment. Chlorites were reacted with 1M to 10M HCl at temperatures up to 80°C and for periods up to five months. After all treatments, chlorites show extensive leaching of iron, magnesium and aluminum, and their crystalline structure is destroyed. However, despite these major compositional and structural changes, chlorites show little or no visible evidence of acid attack, with precise morphological detail of individual plates preserved in all samples following acid treatments. Chlorite dissolution, sensu stricto, did not occur as a result of acidization of the host sandstones. Acid-treated chlorides are likely to exits in a structurally weakened state that may make them susceptible to physical disintegration during fluid flow. Accordingly, fines migration may be a significant engineering problem associated with the acidization of chlorite-bearing sandstones. © 1993.

Emplacement of pyroclastic deposits offshore Montserrat : insights from 3D seismic data

During the current (1995-present) eruptive phase of the Soufrière Hills volcano on Montserrat, voluminous pyroclastic flows entered the sea off the eastern flank of the island, resulting in the deposition of well-defined submarine pyroclastic lobes. Previously reported bathymetric surveys documented the sequential construction of these deposits, but could not image their internal structure, the morphology or extent of their base, or interaction with the underlying sediments. We show, by combining these bathymetric data with new high-resolution three dimensional (3D) seismic data, that the sequence of previously detected pyroclastic deposits from different phases of the ongoing eruptive activity is still well preserved. A detailed interpretation of the 3D seismic data reveals the absence of significant (> 3. m) basal erosion in the distal extent of submarine pyroclastic deposits. We also identify a previously unrecognized seismic unit directly beneath the stack of recent lobes. We propose three hypotheses for the origin of this seismic unit, but prefer an interpretation that the deposit is the result of the subaerial flank collapse that formed the English's Crater scarp on the Soufrière Hills volcano. The 1995-recent volcanic activity on Montserrat accounts for a significant portion of the sediments on the southeast slope of Montserrat, in places forming deposits that are more than 60. m thick, which implies that the potential for pyroclastic flows to build volcanic island edifices is significant.

固井工程中的流动问题

同井是油气在建过程中的重要工程，一般分下套管和注水泥两个过程．本文结合作者近年来的研究，着重阐述了钻井液、前置液、水泥浆在环形空间中流动的流体力学问题，包括：高温高压下的水泥浆流变性、偏心环形空间中浆液的流动特性、钻井液-前置液和前置液-水泥浆界面的稳定性等，介绍了国内外学者对这些问题的研究进展，提出了今后应深入研究的问题.

电潜泵井生产动态分析

提出了原油物性模拟的修正模型，其结果与PVT曲线具有良好的相关性。给出了电潜泵内流体温升及井筒中流体温度梯度的计算方法。通过引入井眼轨迹的描述与计算描述，成功地解决了弯曲井段的多相流计算问题，从而可以计算出任意井眼形状中的参数分布规律。在此基础上，借助于毛细管、动液面或泵特性测试资料，实现了对电潜泵井生产动态的模拟和分析，并在现场应用中收到了良好的效果。

Survey of veterinery [sic] drug residues, environmental contaminants and mycotoxins of cultured shirmp [sic] in Iran

Economical achievement of optimal growth in developing countries may lead to sustainable poverty reduction. Agricultural activities play an important role in economy and human being welfare, which leads to establishment of food security and quality. Aquaculture products in developing countries share 51.4 percent of total agricultural production.7—percent in developed countries. Therefore undoutedly food production by means of quality and quantity has to be increased .The history of shirmp production goes back to 500 years ago. Today 50 countries of the world produce shirmp .In Islamic Republic of Iran shrimp production started since 1992 in the coastal region of Persian Gulf. The shrimp culture farms canbe classified in to 4 different categories; Extensive, semi-extensive, intensive and super instensive. Global ecological manitenanc is one of the major concerns of authorities Human manipulation of nature is the most destructive activity. Industrial sweage leakage in to the rivers and water sources is a big issue that causes reduction in the aquatic population. Heavy metals have an inhibitory effect in the production and growth of sealife. Human intake of food treated with anti microbial cause's allergy, hypersensitivity and develops microbial resistance. Organochlorine compounds contamination may found in hepato pancreatic tissues of aquatic products, Aresnic may transfer to man via plant & animal product contamination. In 1991 during Persian Gulf Mir 700 oil well set

知识表达语言(NFA)及其在石油测井解释专家系统中的应用

石油测井解释是一项逻辑推理和数值计算交错进行的复杂过程。为了描述测井解释专家的这种知识、经验并模拟其思维方式,在扩充纯产生式规则的基础上,我们开发了知识表达语言——NFA,它把逻辑推理和数值计算综合成统一的形式。石油测井解释专家系统 LIX 先后在 INTERDATA-85机和 PE-3230机上实现,现场(胜利油田)运行近两年,解释了130余口井,符合率94%以上。LIX 实质上是 NFA 语言的解释系统,它的研制成功,说明了 NFA 语言的有效性和实用性。