Dielectric properties of some MM′O4 and MTiM′O6 (M=Cr, Fe, Ga; M′=Nb, Ta, Sb) rutile-type oxides

We describe an investigation of the structure and dielectric properties of MM'O-4 and MTiM'O-6 rutile-type oxides for M = Cr, Fe, Ga and M' = Nb. Ta and Sb. All the oxides adopt a disordered rutile structure (P4(2)/mnm) at ambient temperature. A partial ordered trirutile-type structure is confirmed for FeTaO4 from the low temperature (17 K) neutron diffraction studies While both the MM'O-4 oxides (CrTaO4 and FeTaO4) investigated show a normal dielectric property MTiM'O-6 oxides for M = Fe, Cr and M' = Nb/Ta/Sb display a distinct relaxor/relaxor-like response. Significantly the corresponding gallium analogs, GaTiNbO6 and GaTiTaO6, do not show a relaxor response at T<500K (C) 2010 Elsevier Inc All rights reserved

Spinodal decomposition of a Co-Ti-Nb alloy

The microstructural evolution on aging a Co-3 wt pct Ti-2 wt pct Nb alloy has been followed by transmission electron microscopy and diffraction to show that the solid solution decomposed by the spinodal mode. The strengthening observed has been correlated with the differences in lattice parameters of the coexisting phases. The several stages of coarsening have been documented to yield information about their kinetics and morphological changes.Formerly Visiting Assistant Professor, Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, 1206 West Green Street, Urbana, IL 61801, is with .

Probing disorder in cubic pyrochlore Bi-1 Zn-5(1) Nb-0(1) O-5(7) (BZN) thin films

The dielectric response of pulsed laser ablated Bi-1 Zn-5(1) Nb-0(1) O-5(7) (BZN) thin films are investigated within the temperature range of 300-660 K and frequency range of 100 Hz-100 kHz Thin film exhibited a strong dielectric relaxation behavior A sharp rise in dielectric constant of BZN thin film at high temperatures is related to disorder in canon and anion lattices Observed dielectric relaxation implies a redistribution of charges within the unit cell This phenomenon suggests that the large change in dielectric constant is due to a dynamical rise of dipolar fluctuations in the unit cell XPS spectra of BZN (A(2)B(2)O(6)O') cubic pyrochlore confirm that the relaxation corresponds to the ionic hopping among the A and O' positions of several local potential minima Barrier height for hopping is distributed between 0 and 0 94 eV The O is spectrum confirms presence of two types of oxygen in BZN thin film The disorder in charge neutralized thin film is correlated with XPS spectra (C) 2010 Elsevier Ltd All rights reserved

Synthesis of Layered Perovskite Oxides, ACa2-xLaxNb3-xTix010 (A = K, Rb, Cs), and Characterization of New Solid Acids, HCa2-xLaxNb3-xTixOlo (0 < x d 2), Exhibiting Variable Bronsted Acidity?

Layered perovskite oxides of the formula ACa~,La,Nb3-,Ti,010 (A = K, Rb, Cs and 0 < x d 2) have been prepared. The members adopt the structures of the parent ACazNb3010. Interlayer alkali cations in the niobium-titanium oxide series can be ion-exchanged with Li+, Na+, NH4+, or H+ to give new derivatives. Intercalation of the protonated derivatives with organic bases reveals that the Bronsted acidity of the solid solution series, HC~ ~ , L ~ ,N~ ~ , T ~ ,dOep~eOnd, s on the titanium content. While the x = 1 member (HCaLaNbzTiOlo) is nearly as acidic as the parent HCazNb3010, the x = 2 member (HLazNbTizOlo) is a weak acid hardly intercalating organic bases with pKa - 11.3. The variation of acidity is probably due to an ordering of Nb/Ti atoms in the triple octahedral perovskite slabs, [Ca~,La,Nb~,Ti,0~0], such that protons are attached to NbO6 octahedra in the x = 1 member and to Ti06 octahedra in the x = 2 member.

Soft-chemical synthesis of new non-linear optical materials, K0.5M0.5Ti0.5OPO4(M = Nb, Ta),related to KTiOPO4

Soft-chemical oxidation of KTiOPO4-like KM(0.5)(V)Ti(0.5)(III)OPO(4) (M = Nb, Ta) using chlorine in CHCl3 is accompanied by partial deintercalation of potassium, yielding K(0.5)MV(0.5)Ti(0.5)(IV)OPO(4) compounds which are new non-linear optical materials that exhibit efficient second-harmonic generation of 1064 nm radiation, as does KTiOPO4.

Study of the reaction between 1,2,3-trihydroxybenzene and 8-hydroxyquinoline in the solid state

1.2,3-Trihydroxybenzene (THB) reacts with 8-hydroxyquinoline (8HQ) in the solid state forming an orange-coloured charge transfer complex THB* (8HQ)(2). When the reaction was carried out in a petri dish, or when the vapours of 8HQ were allowed to react with solid THB (gravimetric study), the reaction product separated out as good quality, shiny single crystals. X-Ray diffraction studies on single crystals showed that they belong to the orthorhombic system with a = 15.408(1), b = 16.276(1), c = 7.825(1) Angstrom, Z = 4, D-x = 1.413 g cm(-3) and space group Pnaa. From the crystallographic evidence it has been found that the proton of the middle OH group of THB is transferred to the N atom of 8HQ. This accounts for the observed colour change. Kinetic studies on the solid state reaction showed that the 8HQ molecules diffuse towards THB, and the lateral diffusion occurs through surface migration, grain boundary diffusion and vapour phase diffusion. Gravimetric studies of the reaction between solid THB and 8HQ vapour showed that the diffusion of 8HQ molecules into the crystal lattice of THB has a higher energy of activation than that observed when the reactants are in contact. The nature of the crystal packing in the reaction product indicates diffusion of 8HQ molecules into the crystal lattice of THB along the c-axis, to occupy the cavities present between the THB molecules in the unit cell.

LiSr1.65 square 0.35B1.3B ' O-1.7(9) (B = Ti, Zr; B ' = Nb, Ta): New lithium ion conductors based on the perovskite structure

We describe the design and synthesis of new lithium ion conductors with the formula, LiSr(1.65)rectangle(0.35)B(1.3)B'O-1.7(9) (rectangle = vacancy; B = Ti, Zr; B' = Nb, Ta), on the basis of a systematic consideration of the composition-structure-property correlations in the well-known lithium-ion conductor, La-(2/3-x)Li(3x)rectangle((1/3)-2x)TiO3 (I), as well as the perovskite oxides in Li-A-B,B'-O (A = Ca, Sr, Ba; B = Ti, Zr; B' = Nb, Ta) systems. A high lithium-ion conductivity of ca. 0.12 S/cm at 360 degrees C is exhibited by LiSr(1.65)rectangle(0.35)Ti(1.3)Ta(1.7)O(9) (III) and LiSr(1.65)rectangle(0.35)Zr(1.3)Ta(1.7)O(9) (IV), of which the latter containing stable Zr(IV) and Ta(V) oxidation states is likely to be a candidate electrolyte material for all-solid-state lithium battery application. More importantly, we believe the approach described here could be extended to synthesize newer, possibly better, lithium ion conductors.

Effect of Gallium on microstructure and mechanical properties of Nb-Si eutectic alloy

In this paper, we report a significant improvement in mechanical properties of near eutectic Nb-Si alloys by addition of Gallium (Ga) and control of microstructural length scale. A comparative study of two alloys Nb-18.79 at.%Si and Nb-20.2 at.%Si-2.7 at.%Ga were carried out. The microstructure refinements were carried out by vacuum suction casting in water cooled thick copper mold. It is shown that addition of Ga suppresses Nb(3)Si phase and promotes beta-Nb(5)Si(3) phase. The microstructural length scale and in particular eutectic spacing reduces significantly to 50-100 nm in suction cast ternary alloys. Compression test shows a strength of 2.8 +/- 0.1 GPa and plasticity of 4.3 +/- 0.03%. In comparison, the binary Nb-18.79 at.%Si alloy processed under identical conditions exhibit coarser length scale (300-400 nm) and brittle behavior. The fracture toughness of Ga containing suction cast alloy shows a value of 24.11 +/- 0.5 MPa root m representing a major improvement for bulk Nb-Si eutectic alloy. (C) 2011 Elsevier Ltd. All rights reserved.

Microstructure and mechanical properties of oxidation resistant suction cast Nb-Si-Al alloy

In this paper, we report a significant improvement in mechanical and oxidation properties of near eutectic Nb-Si alloys by the addition of aluminum (Al) and control of microstructural length scale. A comparative study of two alloys Nb-18.79at%Si and Nb-12.3at%Si-9at%Al were carried out. The processing for microstructure refinements were carried out by vacuum suction casting in water cooled thick copper mould. It is shown that addition of Al suppresses Nb3Si phase and promotes beta Nb5Si3 phase under nonequilibrium solidification condition. The microstructural length scale and in particular eutectic spacing reduces significantly to 50-100 nm in suction cast ternary alloy. A detailed TEM study shows the presence of delta-Nb11Si4 phase in Nb matrix. The hardness of Nb solid solution can be increased as a consequence to a level observed in Nb3Si intermetallic due to the well oriented precipitates. Compression test yields the ultimate strength of 1.8 +/- 0.1 GPa and engineering strain of 2.3 +/- 0.03%. In comparison, the binary Nb-18.79 at% Si alloy possesses an ultimate strength of 1.35 +/- 0.1 GPa and strain of 0.2 +/- 0.01% when processed under identical conditions. The latter exhibits coarser microstructural length scale (300-400 nm) and a brittle behavior. The indentation fracture toughness of Al containing suction cast alloy shows a value of 20.2 +/- 0.5 MPa root m which represents a major improvement over bulk Nb-Si eutectic alloy. The detailed thermal studies confirm a multifold improvement in oxidation resistance up to 1000 degrees C. (C) 2012 Elsevier B.V. All rights reserved.

Effect of Mg addition on microstructural, mechanical and environmental properties of Nb-Si eutectic composite

The paper reports the effect of addition of small amount of Mg on the mechanical and oxidation properties of Nb-Nb3Si eutectic composites in Nb-Si system under the condition of suction casting. Mg addition increases the volume fraction of primary dendrites of Nb solid solution. This phase contains significant amount of strengthening precipitates. Two different precipitates are identified. The large plate shaped precipitates are that of hcp phase, while fine coherent precipitates have the structure similar to recently identified delta-Nb11Si2 phase. The Mg addition improves both the strength and ductility of the composite at room temperature (similar to 1.4 GPa and similar to 5% engineering strain) as well as at 700 degrees C(similar to 1.2 GPa and similar to 7% engineering strain). The presence of Mg results in a complex barrier layer which significantly increases the oxidation resistance up to a temperature of at least 1000 degrees C. (C) 2012 Elsevier B.V. All rights reserved.

Effect of Ti concentration on the growth of Nb3Sn between solid Nb(Ti) and liquid Sn

The change in the growth rate of the Nb3Sn product phase because of Ti addition is studied for solid Nb(Ti)-liquid Sn interactions. The growth rate increased from no Ti to 1 at.% and 2 at.% of Ti in Nb, and the activation energy decreased from 221 kJ/mol to 146 kJ/mol. Based on the estimated values, the role of grain boundary and lattice diffusion is discussed in light of the possibility of increased grain boundary area and point defects such as antisites and vacancies.

Microstructural and mechanical behavior study of suction cast Nb-Si binary alloys

The solidification pathways of Nb rich Nb-Si alloys when processed under non-equilibrium conditions require understanding. Continuing with our earlier work on alloying additions in single eutectic composition 1,2], we report a detailed characterization of the microstructures of Nb-Si binary alloys with wide composition range (10-25 at% Si). The alloys are processed using chilled copper mould suction casting. This has allowed us to correlate the evolution of microstructure and phases with different possible solidification pathways. Finally these are correlated with mechanical properties through studies on deformation using mechanical testing under indentation and compressive loads. It is shown that microstructure modification can significantly influence the plasticity of these alloys.

A new tungsten-free gamma-gamma ` Co-Al-Mo-Nb-based superalloy

We present the first report of a tungsten-free cobalt-based superalloy having a composition Co-10Al-5Mo-2Nb. The alloy is strengthened by cuboidal precipitates of metastable Co-3(Al,Mo,Nb) distributed throughout the microstructure. The precipitates are coherent with the face-centred cubic gamma-Co matrix and possess ordered Ll(2) structure. The microstructure is identical to the popular gamma-gamma' type nickel-based superalloys and that of recently reported Co-Al-W-based alloys. Being tungsten free, the reported alloy has higher specific proof stress compared to existing cobalt-based superalloys. (C) 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Evaluación de diferentes niveles de rastrojo, métodos y densidades de siembra, en el cultivo del maiz (Zea mays L.) variedad NB-6

El presente estudio se estableció en terrenos del Centro Experimental La Compañía, ubicado en el municipio de San Marcos departamento de Carazo a una altura de 480 msnm a 11”51 latitud norte y 86”11 latitud Oeste, durante la época de primera que comprende desde el mes de Junio hasta el mes de octubre de 1996, con precipitaciones promedios de 1 400 mm anuales y temperaturas promedio de 24 grados Celcius (INETER, 1996). Esto con el objetivo de evaluar la sembradora combinada PROMECH con el arado egipcio en dos densidades de siembra (50 mil y 65 mil plantas por hectárea), y tres niveles de rastrojo (0.3 y 5 toneladas por hectárea), en el cultivo de maíz (Zea mays, L.) variedad NB-6, se utilizó un diseño de Bloques completamente al azar (BCA), en tres repeticiones. De los resultados obtenidos se observó que el mayor número de plántulas emergió en los tratamientos donde se trabajó con 5 t/ha de rastrojo, con el uso de la Sembradora Combinada y con densidad poblacional de 65 000 plantas /ha con un promedio de 64 291 plantas /ha, el mayor diámetro del tallo se encontró en los tratamientos donde se trabajó con niveles de 3 t/ha de rastrojo, utilizando la sembradora combinada y con densidad poblacional de 50 000 plantas /ha, con un promedio de 2,88 cm de diámetro, el menor número de plantas acamadas se encontró en los tratamientos donde se aplicó 3 t/ha de rastrojo, la sembradora Combinada y densidad poblacional de 50 000 plantas/ha, con un promedio de 2 519 plantas acamadas por hectárea, el mayor número de mazorcas cosechadas se obtuvo con la aplicación de 3 t/ha de rastrojo, utilizando la sembradora combinada y con densidad poblacional de 65 000 plantas /ha, con un promedio de 58 772 mazorcas/ha; la mayor cantidad de biomasa seca (5 41 t/ha), se obtuvo en los tratamientos con aplicación de 3 t/ha de rastrojo, usando la sembradora combinada y con densidad poblacional de 65 000 plantas/ha, el mayor rendimiento (1 439.6 kg/ha) se obtuvo en la tratamientos donde se aplicó la interacción 3 t/ha de rastrojo, usando la sembradora combinada y con densidad poblacional de 50 000 plantas/ha

Efecto de diferentes niveles de nitrógeno y densidades de siembra sobre el crecimiento, desarrollo y rendimiento del cultivo de maiz (Zea mays L.) var. NB-6

Con el propósito de evaluar el efecto de tres niveles de Nitrógeno y tres Densidades de siembra, sobre el crecimiento, desarrollo y rendimiento del cultivo del maíz, Var. NB-6, se estableció un ensayo durante la época de postrera de 1999, en la unidad de producción" El Plantel ", ubicada a 200 msnm, 12° 03' latitud norte y 86° 06' longitud oeste. Los factores en estudio consistieron en Nitrógeno (60,90 y 120 kg 1 ha) y densidad (71000, 85000 y 95000 plts 1 ha). Se utilizó un experimento bifactorial, con arreglo de bloques completamente al azar (B. C. A) con cuatro repeticiones. A los resultados de las variables evaluadas realizó un análisis de varianza (ANDEVA) y separación de rangos múltiples de medias de Duncan con un é2=0.05. Los resultados para el factor Nitrógeno no presentó un significativo para las variables de crecimiento, sin embargo el factor densidades, mostró diferencias significativas para la altura y el contenido de clorofila. En lo que respecta a los componentes del rendimiento el factor Nitrógeno, tuvo influencia significativa para el número de hileras por mazorca, no así para los demás componentes. El factor densidad mostró efecto significativo sobre el número de plantas cosechadas y el rendimiento de grano, obteniéndose el mejor resultado con la densidad de 95000 plts 1 ha. Los resultados del análisis económico muestran que la mejor relación Beneficio/Costo es de 7.2 y se obtuvo con el tratamiento 60 kg /ha de Nitrógeno y 95000 plts /ha.