Gestão do risco em mercados de energia eléctrica recorrendo ao VaR por simulação de Monte Carlo

Mestrado em Engenharia Electrotécnica – Sistemas Eléctricos de Energia.

Fuzzy Monte Carlo model for transmission power systems reliability based decision making

This thesis presents the Fuzzy Monte Carlo Model for Transmission Power Systems Reliability based studies (FMC-TRel) methodology, which is based on statistical failure and repair data of the transmission power system components and uses fuzzyprobabilistic modeling for system component outage parameters. Using statistical records allows developing the fuzzy membership functions of system component outage parameters. The proposed hybrid method of fuzzy set and Monte Carlo simulation based on the fuzzy-probabilistic models allows catching both randomness and fuzziness of component outage parameters. A network contingency analysis to identify any overloading or voltage violation in the network is performed once obtained the system states. This is followed by a remedial action algorithm, based on Optimal Power Flow, to reschedule generations and alleviate constraint violations and, at the same time, to avoid any load curtailment, if possible, or, otherwise, to minimize the total load curtailment, for the states identified by the contingency analysis. For the system states that cause load curtailment, an optimization approach is applied to reduce the probability of occurrence of these states while minimizing the costs to achieve that reduction. This methodology is of most importance for supporting the transmission system operator decision making, namely in the identification of critical components and in the planning of future investments in the transmission power system. A case study based on Reliability Test System (RTS) 1996 IEEE 24 Bus is presented to illustrate with detail the application of the proposed methodology.

Mass conservative three-dimensional water tracer distribution from Markov chain Monte Carlo inversion of time-lapse ground-penetrating radar data

Time-lapse geophysical measurements are widely used to monitor the movement of water and solutes through the subsurface. Yet commonly used deterministic least squares inversions typically suffer from relatively poor mass recovery, spread overestimation, and limited ability to appropriately estimate nonlinear model uncertainty. We describe herein a novel inversion methodology designed to reconstruct the three-dimensional distribution of a tracer anomaly from geophysical data and provide consistent uncertainty estimates using Markov chain Monte Carlo simulation. Posterior sampling is made tractable by using a lower-dimensional model space related both to the Legendre moments of the plume and to predefined morphological constraints. Benchmark results using cross-hole ground-penetrating radar travel times measurements during two synthetic water tracer application experiments involving increasingly complex plume geometries show that the proposed method not only conserves mass but also provides better estimates of plume morphology and posterior model uncertainty than deterministic inversion results.

Monte Carlo study of the relation between vacancy diffusion and domain growth in two-dimensional binary alloys

Domain growth in a two-dimensional binary alloy is studied by means of Monte Carlo simulation of an ABV model. The dynamics consists of exchanges of particles with a small concentration of vacancies. The influence of changing the vacancy concentration and finite-size effects has been analyzed. Features of the vacancy diffusion during domain growth are also studied. The anomalous character of the diffusion due to its correlation with local order is responsible for the obtained fast-growth behavior.

Strategisten reaalioptioiden mallintaminen Monte Carlo -simulointimenetelmällä, case Voest Alpine Stahl Ag

Tutkielman päätavoitteena oli selvittää, miten Monte Carlo –simulointi soveltuu strategisten reaalioptioiden arvonmääritykseen. Tutkielman teoriaosuudessa käytiin läpi reaalioptioteoriaa ja Monte Carlo –simulointimenetelmää toiminta-analyyttisella tutkimusotteella. Tuloksena todettiin, että simulointimenetelmää on reaalioptioiden yhteydessä yleensä käytetty, kun muu menetelmä ei ole ollut mahdollinen. Tutkielman pääpaino on tapaustutkimukseen pohjautuvassa empiriaosuudessa, jossa rakennettiin päätöksentekometodologista tutkimusotetta seuraten simulointimalli, jolla tutkittiin Voest Alpine Stahl Ag:n vaihtoehtoisten hinnoittelustrategioiden taloudellista vaikutusta. Mallin rakentaminen perustui yrityksen tilinpäätösaineistoon. Havaittiin, ettei yritys ole valitsemansa strategian vuoksi juurikaan menettänyt tuottoja, mutta toisaalta pelkkä tilinpäätösaineisto ei riitä kovin luotettavaan tarkasteluun. Vuosikertomusten antaman tiedon pohjalta analysoitiin lisäksi yrityksen toiminnassa havaittuja reaalioptioita. Monte Carlo –simulointimenetelmä sopii reaalioptioiden arvonmääritykseen, mutta kriittisiä tekijöitä ovat mallin rakentaminen ja lähtötietojen oikeellisuus. Numeerisen mallin rinnalla on siksi aiheellista suorittaa myös laadullista reaalioptioanalyysia.

Termodinâmica estatística de líquidos com o método de Monte Carlo. I. Metodologia

Statistical mechanics Monte Carlo simulation is reviewed as a formalism to study thermodynamic properties of liquids. Considering the importance of free energy changes in chemical processes, the thermodynamic perturbation theory implemented in the Monte Carlo method is discussed. The representation of molecular interaction by the Lennard-Jones and Coulomb potential functions is also discussed. Charges derived from quantum molecular electrostatic potential are also discussed as an useful methodology to generate an adequate set of partial charges to be used in liquid simulation.

Termodinâmica estatística de líquidos com o método de Monte Carlo. II. O líquido clorofórmio

Thermodynamic properties and radial distribution functions for liquid chloroform were calculated using the Monte Carlo method implemented with Metropolis algorithm in the NpT ensemble at 298 K and 1 atm. A five site model was developed to represent the chloroform molecules. A force field composed by Lennard-Jones and Coulomb potential functions was used to calculate the intermolecular energy. The partial charges needed to represent the Coulombic interactions were obtained from quantum chemical ab initio calculations. The Lennard-Jones parameters were adjusted to reproduce experimental values for density and enthalpy of vaporization for pure liquid. All thermodynamic results are in excelent agreement with experimental data. The correlation functions calculated are in good accordance with theoretical results avaliable in the literature. The free energy for solvating one chloroform molecule into its own liquid at 298 K and 1 atm was computed as an additional test of the potential model. The result obtained compares well with the experimental value. The medium effects on cis/trans convertion of a hypotetical solute in water TIP4P and chloroform solvents were also accomplished. The results obtained from this investigation are in agreement with estimates of the continuous theory of solvation.

Vacancy-assisted domain-growth in asymmetric binary alloys: A Monte Carlo Study

A Monte Carlo simulation study of the vacancy-assisted domain growth in asymmetric binary alloys is presented. The system is modeled using a three-state ABV Hamiltonian which includes an asymmetry term. Our simulated system is a stoichiometric two-dimensional binary alloy with a single vacancy which evolves according to the vacancy-atom exchange mechanism. We obtain that, compared to the symmetric case, the ordering process slows down dramatically. Concerning the asymptotic behavior it is algebraic and characterized by the Allen-Cahn growth exponent x51/2. The late stages of the evolution are preceded by a transient regime strongly affected by both the temperature and the degree of asymmetry of the alloy. The results are discussed and compared to those obtained for the symmetric case.

Simulação Monte Carlo no ensino de luminescência e cinética de decaimento de estados excitados

A software based in the Monte Carlo method have been developed aiming the teaching of important cases of mechanisms found in luminescence and in excited states decay kinetics, including: multiple decays, consecutive decays and coupled systems decays. The Monte Carlo Method allows the student to easily simulate and visualize the luminescence mechanisms, focusing on the probabilities of the related steps. The software CINESTEX was written for FreeBASIC compiler; it assumes first-order kinetics and any number of excited states, where the pathways are allowed with probabilities assigned by the user.

Simulação Monte Carlo de mecanismo de transferência de energia de excitação eletrônica: modelo de Perrin para a supressão estática da luminescência

A software based in the Monte Carlo method has been developed aiming the teaching of the Perrin´s model for static luminescence quenching. This software allows the student to easily simulate the luminescence decays of emissive molecules in the presence of quenching ones. The software named PERRIN was written for FreeBASIC compiler and it can be applied for systems where the molecules remain static during its excited state lifetime. The good agreement found between the simulations and the expected theoretical results shows that it can be used for the luminescence and excited states decay kinetic teaching.

Vacancy-assisted domain-growth in asymmetric binary alloys: A Monte Carlo Study

A Monte Carlo simulation study of the vacancy-assisted domain growth in asymmetric binary alloys is presented. The system is modeled using a three-state ABV Hamiltonian which includes an asymmetry term. Our simulated system is a stoichiometric two-dimensional binary alloy with a single vacancy which evolves according to the vacancy-atom exchange mechanism. We obtain that, compared to the symmetric case, the ordering process slows down dramatically. Concerning the asymptotic behavior it is algebraic and characterized by the Allen-Cahn growth exponent x51/2. The late stages of the evolution are preceded by a transient regime strongly affected by both the temperature and the degree of asymmetry of the alloy. The results are discussed and compared to those obtained for the symmetric case.

THz Plasma Waves in Field-Effect-Transistors: A Monte Carlo Study

Sensing with electromagnetic waves having frequencies in the Terahertz-range is a very attractive investigative method with applications in fundamental research and industrial settings. Up to now, a lot of sources and detectors are available. However, most of these systems are bulky and have to be used in controllable environments such as laboratories. In 1993 Dyakonov and Shur suggested that plasma waves developing in field-effect-transistors can be used to emit and detect THz-radiation. Later on, it was shown that these plasma waves lead to rectification and allows for building efficient detectors. In contrast to the prediction that these plasma waves lead to new promising solid-state sources, only a few weak sources are known up to now. This work studies THz plasma waves in semiconductor devices using the Monte Carlo method in order to resolve this issue. A fast Monte Carlo solver was developed implementing a nonparabolic bandstructure representation of the used semiconductors. By investigating simplified field-effect-transistors it was found that the plasma frequency follows under equilibrium conditions the analytical predictions. However, no current oscillations were found at room temperature or with a current flowing in the channel. For more complex structures, consisting of ungated and gated regions, it was found that the plasma frequency does not follow the value predicted by the dispersion relation of the gated nor the ungated device.

Analytical and Monte Carlo approaches to evaluate probability distributions of interruption duration

Regulatory authorities in many countries, in order to maintain an acceptable balance between appropriate customer service qualities and costs, are introducing a performance-based regulation. These regulations impose penalties-and, in some cases, rewards-that introduce a component of financial risk to an electric power utility due to the uncertainty associated with preserving a specific level of system reliability. In Brazil, for instance, one of the reliability indices receiving special attention by the utilities is the maximum continuous interruption duration (MCID) per customer.This parameter is responsible for the majority of penalties in many electric distribution utilities. This paper describes analytical and Monte Carlo simulation approaches to evaluate probability distributions of interruption duration indices. More emphasis will be given to the development of an analytical method to assess the probability distribution associated with the parameter MCID and the correspond ng penalties. Case studies on a simple distribution network and on a real Brazilian distribution system are presented and discussed.

Aplicação da Simulação de Monte Carlo no estudo de testes de fadiga em rodas agrícolas

Due to the increasing demand from clients and the search for better performances in the heavy vehicles industry, a progressive evolution in technology in a general way was needed. This paper uses a scientific method to validate, prior to its manufacture, the project of an agricultural wheel for sugar cane harvesters. Monte Carlo Simulation is used in conjunction with Finite Elements Method, in order to simulate the wheel's behavior in a cornering test, identify possible failure regions and get an estimate for its life under fatigue. To this end, test conditions according to EUWA Standards were simulated and obeyed, relevant to fatigue. Simulation results were interesting, according to industry experts involved in the project and manufacture of the product in question, and have provided important elements for the decision making regarding improvements that could be made on the product project before its execution

Aplicação da Simulação de Monte Carlo no estudo de testes de fadiga em rodas agrícolas

Due to the increasing demand from clients and the search for better performances in the heavy vehicles industry, a progressive evolution in technology in a general way was needed. This paper uses a scientific method to validate, prior to its manufacture, the project of an agricultural wheel for sugar cane harvesters. Monte Carlo Simulation is used in conjunction with Finite Elements Method, in order to simulate the wheel's behavior in a cornering test, identify possible failure regions and get an estimate for its life under fatigue. To this end, test conditions according to EUWA Standards were simulated and obeyed, relevant to fatigue. Simulation results were interesting, according to industry experts involved in the project and manufacture of the product in question, and have provided important elements for the decision making regarding improvements that could be made on the product project before its execution