Comparing detection and location performance of perpendicular and parallel broadside GPR antenna orientations

GPR (Ground Penetrating Radar) results are shown for perpendicular broadside and parallel broadside antenna orientations. Performance in detection and localization of concrete tubes and steel tanks is compared as a function of acquisition configuration. The comparison is done using 100 MHz and 200 MHz center frequency antennas. All tubes and tanks are buried at the geophysical test site of IAG/USP in Sao Paulo city, Brazil. The results show that the long steel pipe with a 38-mm diameter was well detected with the perpendicular broadside configuration. The concrete tubes were better detected with the parallel broadside configuration, clearly showing hyperbolic diffraction events from all targets up to 2-m depth. Steel tanks were detected with the two configurations. However, the parallel broadside configuration was generated to a much lesser extent an apparent hyperbolic reflection corresponding to constructive interference of diffraction hyperbolas of adjacent targets placed at the same depth. Vertical concrete tubes and steel tanks were better contained with parallel broadside antennas, where the apexes of the diffraction hyperbolas better corresponded to the horizontal location of the buried target disposition. The two configurations provide details about buried targets emphasizing how GPR multi-component configurations have the potential to improve the subsurface image quality as well as to discriminate different buried targets. It is judged that they hold some applicability in geotechnical and geoscientific studies. (C) 2009 Elsevier B.V. All rights reserved.

Mineralogical and microthermometric studies and structural aspects of imperial topaz mineralization in Antonio Pereira, Ouro Preto District (Minas Gerais) - Brazil

The occurrences of imperial topaz in the Antonio Pereira mine, Ouro Preto, Minas Gerais, are associated with the metamorphic carbonate rocks of the Minas Supergroup. The crystals have densities varying from 3.46 to 3.58. The parameters of the unitary cells obtained were: 4.658 to 4.663 angstrom (ao), 8.823 to 8.832 angstrom (b(o)), 8.382 to 8.389 angstrom (c(o)), and 344.65 to 345.46 angstrom 3 (V). The refraction indices presented the following variations: 1.622 to 1.630 (nX), 1.624 to 1.632 (nY), 1.633 to 1.640 (nZ), and 0.008 to 0.011 (B). These properties are coherent with the low fluorine contents obtained (16,48%/17,05wt%). Infrared spectroscopy and microthermometry showed that the fluid inclusions, which represent the mineralizing fluids, are formed by H(2)O (with Ca(2+), Mg(2+) and Na(+)), and CO(2) +/- CH(4). The minimal trapping T-P conditions of 290/320 degrees C and 2,349/2,497bar were obtained for the primary fluid inclusions. The pseudo-secondary fluid inclusions were trapped at conditions of lower temperatures and variable pressures, during the deformation process under local alternating states of stress. The microthermometric studies, the structural analysis and the fluorine contents suggest that the mineralized veins were formed from hydrothermal fluids originated during the Brasiliano tectono-metamorphic event.

Fluoride in the groundwater of the Tubarao and Crystaline aquifers, Salto-Indaiatuba region (SP)

Anomalous concentrations of fluoride in groundwater were identified in 19 drilling wells in the Salto-Indaiatuba region, Sao Paulo State, with an average concentration of 3.03 mg dm(-3) and a maximum of 6.95 mg dm(-3), which constitute a restriction for the water`s usage in terms of human consumption. The wells exploit water from the Tubarao Aquifer (sedimentary, granular) and Crystalline Aquifer (granitic, fractured), used for sanitary or industrial purposes. These groundwaters are typically HCO(3) and HCO(3)-SO(4) types, with high concentrations of HCO(3) -and Na(+) and high pH-values between 7.5 and 10.0. The highest concentrations of F-are associated to the Tubarao and Tubarao/Crystalline aquifer drilling wells. The presence of F-in groundwater is controlled by these high pH-values, alkalinity, and fluorine availability. The source of fluoride in the Tubarao and Crystalline Aquifers can be related to the percolation of hydrothermal fluids associated with Mesozoic lava flow, emplaced due to the opening of Atlantic Ocean and/or hydrolysis of fluorine-rich minerals and clay minerals.

Neopaleozoic striated surfaces in the granitic basement and clast pavement remains of Salto, SP

Near Guarau Ceramic, localized southwest of Salto city in the State of Sao Paulo, two granite outcrops, distant some tens of meters from each other, display Neopaleozoic striated surfaces. These surfaces are in contact with diamictites from the Itarare Subgroup. The striae correspond to sub parallel grooves with millimetric spacing and depth, oriented about N48E and dipping 12 degrees to 42 degrees towards SE. Observed features and association with diamictites indicate an origin by glacial abrasion due to ice movement from southeast towards northwest. About 1.8 km east of Salto, unconsolidated material containing flat-iron-shaped and striated clasts was found on top of granite outcrops, interpreted as clasts pavement remains.

Comparative electrochemical study of 5832-9 stainless steel at different media of biological interest

The electrochemical behavior of ISO 5832-9 stainless steel at 37 degrees C in 0.9% NaCl, Ringer Lactate and minimum essential medium (MEM) has been studied, using linear voltammetry, and surface analysis by SEM and EDS. Mechanical and toxicity tests were made. ISO 5832-9 is passivated at corrosion potential (E) and it does not present pitting corrosion on the media studied from to 50 in V above the transpassivation potential (Ei). SEM and EDS analysis have shown that the sample previously immersed in MEM presents a diffirent behavior at 50 in V above El: the manganese oxide inclusions are absent in the surface. E. values and passivation current density values j(pass) changed according to the following. E(corr, RL) < E(corr,NaCl) < E(corr, MEM) and J (MEM) << j(RL) congruent to j(NaCl) The stainless steel was characterized as non toxic in the cytotoxicity assay

Study of electrochemical behavior of azoles for AISI 430 stainless steel in H(2)SO(4) 1 mol L(-1)

Corrosion is an undesirable process that occurs in metallic materials. Studied was the effect of inhibiting Benzotriazole (BTAH), Benzimidazole (BZM) and Indole in different concentrations-for the stainless steel (SS) AISI 430 in H(2)SO(4) mol The techniques employed this research were: anodic potenciostatic polarisation, electrochemical impedance spectroscopy, optical microscopy and scanning electron microscopy The curves of anodic polarisation showed that BTAH, BZM and Indol act as corrosion inhibitors for 430 SS, at concentrations of 1x10(-3) and 5x10(-4) mol L(-1) but do not inhibit corrosion for concentrations equal to or less than 1x10(-4) mol L(-1). The in-crease of the efficiency in relation to the inhibitory substances studied followed this order: Indol

The corrosion of austenitic 304 stainless steel in biodiesel

Fuel distribution uses 304 stainless steel containers for the storage of biofuels, however there are few reports in the literature about the corrosive aspects this. steel in biodiesel. The objective of this research is to study the corrosive behavior of 304 austenitic stainless steel in the presence of biodiesel, unwashed and washed, with aqueous solutions of citric, oxalic, acetic and ascorbic acids 0,01 mol L(-1), and compare with results obtained for the copper (ASTM D130). The employedtechniques were: atomic absorption spectrometry (AAS) and optical microscopy (OM). The results of EA A showed a low rate of corrosion for the stainless steel, the alloys elements studied were Cr, Ni and Fe, the highest rate was observed for the chrome, 1.78 ppm / day in biodiesel with or without washing. The OM of the 304 steel, when compared with that of copper has a low corrosion rate in the 304 steel/biodiesel system. Not with standing, this demonstrates that not only the 304 steel, but also the copper corrodes in biodiesel

Electrochemical behavior of the cistein and diphosfonate for stainless steel in media of HCl 1 mol L(-1)

Amino acids and self assembled monolayers (SAM`s) have been studied as to their inhibiting action on the corrosion of metallic materials. The objective of work is to study the electrochemical behavior of the cisteincisteine, the diphosfonate and the mixture of both in inhibiting the action of corrosion on stainless steel 304 in HCl 1 molL(-1). As the following techniques were used: open circuit potential (OCP), potenciostatic anodic polarization (A P), chronoamperomeny (CA), electrochemical impedance spectroscopy (EIS) and optical microscopy (OM). The results of CA showed that cisteine has a double effect, catalytic and inhibiting, in function of the immersion time of the metallic part in the electrolytic solution. AP curves have shown lesser current density for the system containing cisteine diphosfonate suggesting an inhibiting synergic action. These results have been confirmed by EIS and OM.

'Green' treatment of acid mine drainage - a step towards sustainability

Sustainability is becoming increasingly important in the mining and mineral processing industries and must incorporate the associated waste products. Acid mine drainage (AMD) is one such by-product and is one of the most serious environmental problems facing the minerals industry today. The oxidation of sulphidic mine wastes often continues for a substantial period of time after mine closure, resulting in difficult and costly remediation and rehabilitation works. Mining companies are often reluctant to spend increasing amounts of money on waste treatment when the mine life is limited or even finished. Hence a simple, low maintenance and low-cost method of treating AMD is required. Whilst this paper does not address the issue of AMD, it does propose methods for removal of individual species from AMD with potential benefits, including raising AMD pH.

A novel concept of using biosolids as a biological adsorbent, or ‘biosorbent’, of metals from AMD is being investigated at a laboratory/pilot scale level. Biosolids are a by-product resulting from the biological treatment of wastewater, and have been previously shown to adsorb metals from aqueous solutions. This could lead to an environmentally sustainable or ‘green’ method for treating both AMD discharges and disposing/reusing the biosolids.

The result of a laboratory-scale study of the biosorption of Zn(II) is presented in this paper. Physical parameters including reaction kinetics, mixing speed and solution pH were investigated. Solution pH also rose an average of 2 pH units over the 24 hour equilibrium time – a valuable side effect when treating acid mine drainage. The outcome of the study highlights the usefulness of biosolids as a biosorbent for the removal/recovery of metal ions from acid mine drainage. A simple, low-cost treatment technology requiring low maintenance would be beneficial to the mining industry to address some issues relating to AMD and would help integrate environmental and economic considerations into sustainable environmental management.

Thinning of a vertical free draining aqueous film incorporating colloidal particles

The drainage under gravity of a vertical foam film formed on a wire frame has been investigated. Dual-wavelength optical interferometry was used so that unambiguous fringe order assignments could be made, enabling absolute film thicknesses to be calculated with confidence. Films were stabilized by nonionic polypropylene glycol surfactant. Halfmicrometer silica particles with varying degrees of hydrophobicity were added to the film-forming liquid to investigate their effect on film drainage rate and stability. Hydrophilic particles had little or no effect, while hydrophobic particles slowed the drainage of the film and caused a minor increase in film lifetime, from ∼10 to ∼30 s. In both the hydrophilic and hydrophobic cases the films ruptured when they reached a thickness of ∼2 particle diameters. Particles of intermediate hydrophobicity had the most significant effect, increasing film lifetime by an order of magnitude over that for hydrophilic particles. The intermediate particles allowed films to thin down to a thickness less than the particle diameter, indicating that particles bridge across the entire film. This did not occur with more hydrophobic particles even though they were embedded in each of the two film surfaces. These results correlate well with previous literature on particle-laden foams. The film thickness and drainage measurements allow drainage mechanisms for the different particles to be identified, thus providing a mechanistic explanation for the observation by several previous authors that foams formed in the presence of particles, for example during mineral processing, have the greatest stability when the particles are of intermediate hydrophobicity.

Variações em trajetórias de acumulação de capacidades tecnológicas em nível intra-empresarial: uma análise empírica da VALE S.A.

Esta tese relaciona-se ao tema da acumulação de capacidades tecnológicas em nível de empresa, suas fontes (mecanismos de aprendizagem) e suas implicações para a performance competitiva empresarial, em indústrias relacionadas a recursos naturais no contexto de economias emergentes. Durante os últimos 40 anos muito se avançou no campo da pesquisa sobre acumulação de capacidades tecnológicas em nível de empresas em economias emergentes. Porém, ainda há importantes lacunas a serem exploradas particularmente em relação a natureza e dinâmica de trajetórias de acumulação de capacidades tecnológicas intra-empresariais, no contexto de indústrias relacionadas a recursos naturais, especialmente na mineração. O objetivo da pesquisa aqui reportada é contribuir para minimizar esta lacuna. Particularmente, esta tese explora variações intra-empresariais de trajetórias de acumulação de capacidades tecnológicas, suas fontes (mecanismos subjacentes de aprendizagem) e algumas implicações que são geradas para a performance competitiva da empresa, no âmbito da indústria de mineração no Brasil, especificamente na empresa mineradora Vale, no período entre 1942 e 2015. Para alcançar este objetivo, a pesquisa apoia-se na combinação das literaturas de acumulação de capacidade tecnológica, inovação, aprendizagem e desenvolvimento industrial para a construção da base conceitual. Em paralelo, a pesquisa vale-se de um desenho de pesquisa qualitativo e indutivo baseado em evidências primárias com base em extensivos trabalhos de campo. Esse desenho de pesquisa é operacionalizado a partir de um estudo de caso individual em profundidade na Vale, no âmbito de três grandes áreas tecnológicas: prospecção e pesquisa mineral, lavra, e processamento mineral. Por meio da implementação dessa estratégia, a pesquisa encontrou: (1) Trajetórias de acumulação de capacidades tecnológicas relativamente distintas entre as três áreas de análise. Especificamente: (i) na área de prospecção e pesquisa mineral observou-se uma trajetória de seguidora tecnológica que alcança posição de liderança mundial em inovação e produção; (ii) na área de lavra também evidenciou-se uma trajetória de seguidora tecnológica que alcança posição de liderança mundial em inovação e produção, porém, com acumulação tardia de capacidades tecnológicas; e (iii) na área de processamento mineral houve o alcance precoce de posição de liderança mundial em inovação e produção a partir da criação de uma trajetória distinta da já mapeada pelos líderes globais. As trajetórias de acumulação de capacidades tecnológicas convergem para uma situação similar a partir de 2011 quando as três áreas apresentaram posição de liderança mundial em inovação e ao mesmo tempo demonstraram indícios de entrada em um processo de estagnação, que restringe as oportunidades de entrada em novas trajetórias tecnológicas e de entrada em novos negócios. (2) As variações encontradas nas trajetórias de acumulação de capacidades tecnológicas são explicadas pela maneira pela qual diferentes mecanismos subjacentes de aprendizagem foram combinados e utilizados pela empresa. Foram encontradas quatro combinações de mecanismos de aprendizagem que contribuíram para explicar as diferentes direções das trajetórias de acumulação de capacidades tecnológicas. (3) As variações nas três trajetórias de acumulação de capacidades tecnológicas geraram implicações distintas para a performance competitiva, mais especificamente em termos de performance inovadora, operacional/ambiental e de novos negócios. Os resultados da pesquisa geram contribuições para o entendimento do relacionamento intra-empresarial entre acumulação de capacidades tecnológicas e os mecanismos de aprendizagem subjacentes. E contribuem para o entendimento da mineração como uma indústria que oferece oportunidades para inovações significativas que, inclusive podem implicar na diversificação do tecido industrial nacional. Portanto, tal indústria deve receber atenção especial por parte de decisores de políticas públicas e de ações empresariais para evitar que empresas com alto potencial inovativo desconstruam suas capacidades inovadoras e consequentemente limitem seus impactos para o desenvolvimento tecnológico e econômico no contexto de economias emergentes.

DESIGN AND TEST OF A 7-T SPLIT-PAIR MAGNET FOR MAGNETIC SEPARATION

A 160 mm bore, 7 T split-pair magnet was constructed and tested aiming to mineral processing through HGMS (high gradient magnetic separation) or HCMS (helical channel magnetic separation.) This work describes the design and test results of the pair of coils operating under current in parallel mode. In the case of antiparallel current mode large repulsive force between coils is generated and a strong magnetic field gradient outside the magnet is created. A continuous magnetic separation system made with a helical channel magnetic separator for application in TiO2 processing is analysed.

Estudo de genes envolvidos no processo de adesão do Acidithiobacillus ferrooxidans em calcopirita (CuFe'S.IND.2')

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Bacterial and chemical leaching of chalcopyrite concentrates as affected by the redox potential and ferric/ferrous iron ratio at 22 degrees C

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Determination of heavy metals and genotoxicity of water from an artesian well in the city of Vazante- MG, Brazil

The city of Vazante-MG is of great socioeconomic and environmental interest because it is the most important zinc producer district of Brazil. The mineral processing and geochemical processes may determine high concentrations of heavy metals in water intended for human consumption. Thus, the present study aimed to quantify and evaluate the heavy metal genotoxicity of artesian water in the city by Atomic absorption spectrophotometer analysis and testing with the Allium cepa test, respectively. This study reveals a chemical contamination in well water in the city, caused by the presence of heavy metals. Therefore, it can be considered that the high levels of heavy metals found in water samples are correlated with the genotoxic events observed in root cells of A. cepa.