Xanthine biosensor based on didodecyldimethylammonium bromide modified pyrolytic graphite electrode

The vesicle of didodecyldhnethylammonimn bromide (DDAB) which contained tetrathiafulvalene (TTF) was mixed with xanthine oxidase, and the mixture was cast on the pyrolytic graphite electrode. The lipid films were used to supply a biological environment resembling biomembrane on the surface of the electrode. TTF was used as a mediator because of its high electron-transfer efficiency. A novel xanthine biosensor based on cast DDAB film was developed. The effects of pH and operating potential were explored for optimum analytical performance by using the amperometric method. The response time of the biosensor was less than 10 s. The detection limit of the biosensor was 3.2 x 10(-7) mol/L and the liner range was from 4 x 10(-7) mol/L to 2.4 x 10(-6) mol/L.

波前重建法射线追踪及走时表压缩

As a fast and effective method for approximate calculation of seismic numerical simulation, ray tracing method, which has important theory and practical application value, in terms of seismic theory and seismic simulation, inversion, migration, imaging, simplified from seismic theory according to geometric seismic, means that the main energy of seismic wave field propagates along ray paths in condition of high-frequency asymptotic approximation. Calculation of ray paths and traveltimes is one of key steps in seismic simulation, inversion, migration, and imaging. Integrated triangular grids layout on wavefront with wavefront reconstruction ray tracing method, the thesis puts forward wavefront reconstruction ray tracing method based on triangular grids layout on wavefront, achieves accurate and fast calculation of ray paths and traveltimes. This method has stable and reasonable ray distribution, and overcomes problems caused by shadows in conventional ray tracing methods. The application of triangular grids layout on wavefront, keeps all the triangular grids stable, and makes the division of grids and interpolation of a new ray convenient. This technology reduces grids and memory, and then improves calculation efficiency. It enhances calculation accuracy by accurate and effective description and division on wavefront. Ray tracing traveltime table, which shares the character of 2-D or 3-D scatter data, has great amount of data points in process of seismic simulation, inversion, migration, and imaging. Therefore the traveltime table file will be frequently read, and the calculation efficiency is very low. Due to these reasons, reasonable traveltime table compression will be very necessary. This thesis proposes surface fitting and scattered data compression with B-spline function method, applies to 2-D and 3-D traveltime table compression. In order to compress 2-D (3-D) traveltime table, first we need construct a smallest rectangular (cuboidal) region with regular grids to cover all the traveltime data points, through the coordinate range of them in 2-D surface (3-D space). Then the value of finite regular grids, which are stored in memory, can be calculated using least square method. The traveltime table can be decompressed when necessary, according to liner interpolation method of 2-D (3-D) B-spline function. In the above calculation, the coefficient matrix is stored using sparse method and the liner system equations are solved using LU decomposition based on the multi-frontal method according to the sparse character of the least square method matrix. This method is practiced successfully in several models, and the cubic B-spline function can be the best basal function for surface fitting. It make the construction surface smooth, has stable and effective compression with high approximate accuracy using regular grids. In this way, through constructing reasonable regular grids to insure the calculation efficiency and accuracy of compression and surface fitting, we achieved the aim of traveltime table compression. This greatly improves calculation efficiency in process of seismic simulation, inversion, migration, and imaging.

改善三维波动方程叠前深度偏移处理效果的方法研究

3D wave equation prestack depth migration is the effective tool for obtaining the exact imaging result of complex geology structures. It's a part of the 3D seismic data processing. 3D seismic data processing belongs to high dimension signal processing, and there are some difficult problems to do with. They are: How to process high dimension operators? How to improve the focusing? and how to construct the deconvolution operator? The realization of 3D wave equation prestack depth migration, not only realized the leap from poststack to prestack, but also provided the important means to solve the difficult problems in high dimension signal processing. In this thesis, I do a series research especially for the solve of the difficult problems around the 3D wave equation prestack depth migration and using it as a mean. So this thesis service for the realization of 3D wave equation prestack depth migration for one side and improve the migration effect for another side. This thesis expatiates in five departs. Summarizes the main contents as the follows: In the first part, I have completed the projection from 3D data point area to low dimension are using de big matrix transfer and trace rearrangement, and realized the liner processing of high dimension signal. Firstly, I present the mathematics expression of 3D seismic data and the mean according to physics, present the basic ideal of big matrix transfer and describe the realization of five transfer models for example. Secondly, I present the basic ideal and rules for the rearrange and parallel calculate of 3D traces, and give a example. In the conventional DMO focusing method, I recall the history of DM0 process firstly, give the fundamental of DMO process and derive the equation of DMO process and it's impulse response. I also prove the equivalence between DMO and prestack time migration, from the kinematic character of DMO. And derive the relationship between DMO base on wave equation and prestack time migration. Finally, I give the example of DMO process flow and synthetic data of theoretical models. In the wave equation prestak depth migration, I firstly recall the history of migration from time to depth, from poststack to prestack and from 2D to 3D. And conclude the main migration methods, point out their merit and shortcoming. Finally, I obtain the common image point sets using the decomposed migration program code.In the residual moveout, I firstly describe the Viterbi algorithm based on Markov process and compound decision theory and how to solve the shortest path problem using Viterbi algorithm. And based on this ideal, I realized the residual moveout of post 3D wave equation prestack depth migration. Finally, I give the example of residual moveout of real 3D seismic data. In the migration Green function, I firstly give the concept of migration Green function and the 2D Green function migration equation for the approximate of far field. Secondly, I prove the equivalence of wave equation depth extrapolation algorithms. And then I derive the equation of Green function migration. Finally, I present the response and migration result of Green function for point resource, analyze the effect of migration aperture to prestack migration result. This research is benefit for people to realize clearly the effect of migration aperture to migration result, and study on the Green function deconvolution to improve the focusing effect of migration.

黄骅坳陷大港探区油气资源潜力与资源结构预测

Facing the problems that Dagang region of Huanghua Depression has high exploration degree and its remaining resource potential and structure are not clear, the theory of Petroleum Accumulation System (PAS) is applied to divide and evaluate the oil/gas systems quantitatively. Then, the petroleum accumulation systems are taken as units to forecast and analyse the oil/gas resources and their structure using statistical methods of sampling analysis of discovery process model and generalized pareto distribution model. The exploration benefit of the unit is estimated using exploration simulation methods. On the basis of the above study, the resource potential of Huanghua Depression is discussed.Huanghua Depression can be diveded into four petroleum accumulation systems, i.e. North PAS5 Middle Qibei PAS, Middle Qinan PAS and South PAS. Each PAS can be diveded futher into several sub- PASs. Using the basic princple of Analytical Hierarchy Process, the method of quantitative evaluation of PAS is established. Then the elements and maturity of PAS are evaluated quantitatively.Taking migration and accumulation units and sub-PASs as prediction units, sampling analysis of discovery process model and generalized pareto distribution model are applied comparatively to forecast the resource structure of eight migration and accumulation units in six PASs of medium-high exploration degree. The results of these two methods are contrasted and analyzed. An examination of X2 data of these two models from exploration samples shows that generalized pareto distribution model is more effective than sampling analysis of discovery process model in Huanghua Depression. It is concluded that minimum and maximum size of reservoir and discovery sequence of reservoirs are the sensitive parameters of these two methods.Aiming at the difficult problem of forecast in low exploration degree, by analysis of relativity between resource parameters and their possible influential geological factors, forecast models for resource parameters were established by liner regressing. Then the resource structure is forecasted in PASs of low exploration degree.Based on the forecast results, beginning with the analysis of exploration history and benefit variation, the exploration benefit variation of the above PASs is fitted effectively using exploration simulation method. The single well exploration benefit of remaining oil resource is also forecasted reasonably.The results of resource forecast show that the total oil resources ofHuanghua Depression amount to 2.28 b illion ton. By the end o f 2 003, the accumulative total proved oil reserve is 0.90 billion ton and the remaining oil resources is 1.38 billion ton. The remaining oil resource is concentrated in Kongdian-Dengmingshi, Banqiao-Beidagang, Qidong-Yangerzhuang and Baidong-Qizhong sub-PASs.

计算机环境下的呈现方式对学生样例学习的影响

This study designed tow experiments to explore the effect of two presentation forms(liner presentation and concept-map navigation presentation)on the student's learning process. Using the method of protocal analysis and the learning path records of these students, the author of this paper further analysed the information-processing process of these students. The main results showed as follows: (1) In the initial study phase, the main effects of both the presentation form and the learner type were obvious, and the interaction effect of these two variables was also obvious. Contrasting with the liner presentation form, the concept map navigation form interfered with the learning process of the student, especially the learning-disabled students. (2) There was a significant difference between excellent students and learning-disabled learning-disabled on self explanations amount. Excellent students produced more self- explanations than learning-disabled students, especially on two phases of learning from the the example and the conclusion. (3) Under the same learning path, the main effect of the learner type variable was obvious, the main effect of the presentation form and interaction effect of these two variables weren't obvious. But the liner presentation grouped still acquired a better result than the concept-map navigation presentation groupe.

The influence of reusing ‘Formtex’ controlled permeability

The effects of the reuse of ‘Formtex’ Controlled Permeability Formwork (CPF) liner on strength and durability properties of concrete were investigated at two different water-cement ratios and the results are reported in this paper. Test blocks were cast using the CPF on one side and impermeable formwork (IF) on the opposite side of the mould so that direct comparisons could be made between the two. The strength was assessed using the Limpet pulloff tester and both the air permeability and the water absorption (sorptivity) were measured using the Autoclam Permeability System. Both these instruments measured the ‘covercrete’ properties. In addition, cores cut from the test specimens were subjected to an accelerated carbonation test and a chloride exposure test. The results showed that the ‘Formtex’ CPF increases the surface strength and the durability of concrete compared to the IF. There was an almost complete elimination of blowholes. The permeability of concrete decreased and its resistance to the ingress of both carbon dioxide and chlorides increased when CPF was used. The beneficial effects of the Formtex CPF were most evident in concrete of higher water-cement ratio. With the reuse of the Formtex liner twice, that is a total of three uses, the performance of the CPF to improve the properties of concrete remained almost the same. In this research the CPF liner was cleaned thoroughly between each use, which must be adhered to for site applications for reproducing the beneficial effects observed in the laboratory.

Durability and water absorption properties of surface treated concretes

Durability of concrete can be improved by applying surface treatments. Pore-lining treatments prevent or delay the ingress of water-borne salts while allowing vapour transfer across the concrete surface. The most common pore-liners are silanes and siloxanes; both reported to give good results. One area of concern, however, is variability in effectiveness of the treatment. This variability may be due to inconsistent coverage or extreme drying conditions. With care these can be controlled but another source of variability which is difficult to control is the moisture profile within the concrete at the time of application of the treatment. This paper describes a test programme to assess the sensitivity of three different surface treatments to moisture gradient in the concrete at the time of application of treatment. The test programme included durability parameters such as chloride ingress, corrosion due to chloride ingress, freeze-thaw salt scaling resistance. Water absorption (sorptivity) of treated and untreated concretes was also measured with a non-distructive test technique called Autoclam with the aim of determining if the Autoclam sorptivity test can be used to assess the effectiveness of surface treatments. Using these results it is possible to avoid, or allow for, moisture conditions which would adversely affect the success of a pore-liner. However there are advantages in specifying an expected performance of the surface treatment rather than specifying the conditions in which it must be placed. By this method a treatment would have to achieve a specified value of sorptivity or a specified reduction in sorptivity. Failure to do so would be an objective basis on which to make a decision of whether or not to reject the treatment. The Autoclam is a device capable of measuring sorptivity values down to the range typical of surface treated concrete. The paper assesses if the device can be used to discriminate between acceptable treatment and unsatisfactory treatments.

Indirect-drive inertial confinement fusion using highly supersonic, radiatively cooled, plasma slugs

We present a new approach to indirect-drive inertial confinement fusion which makes use of highly supersonic, radiatively cooled, slugs of plasma to energize a hohlraum. 2D resistive magnetohydrodynamic simulations of slug formation in shaped liner Z -pinch implosions are presented along with 2D-radiation-hydrodynamic simulations of the slug impacting a converter foil and 3D-view-factor simulations of a double-ended hohlraum. Results for the Z facility at Sandia National Laboratory indicate that two synchronous slugs of 250 kJ kinetic energy could be produced, resulting in a capsule surface temperature of similar to225 eV .

Firing and training costs and labour market segmentation

This dissertation consists of three essays on the labour market impact of firing and training costs. The modelling framework resorts to the search and matching literature. The first chapter introduces firing costs, both liner and non-linear, in a new Keynesian model, analysing business cycle effects for different wage rigidity degrees. The second chapter adds training costs in a model of a segmented labour market, accessing the interaction between these two features and the skill composition of the labour force. Finally, the third chapter analyses empirically some of the issues raised in the second chapter.

How to invest as a private equity

This work project presents a road map for making deals under the umbrella support of a private equity investor. Fundraising, investment analysis, asset monitoring, and divestment are stages in the process that are covered in-depth and clarified in terms of action plan and procedures. Moreover, private equity brings tangible and intangible efficiency to the economy and companies, not only by providing finance to grow and expand but also by forcing superior organizational organics that foster sustainable business positions. In a world domain, Europe as been a second liner as compared to US in terms of size within the private equity sector, but it is quickly maturing and converging to US numbers. In this sense, Portugal has been improving in both numbers and regulations in order to leverage on its strategic location and position itself as a key player to address future business challenges coming from emerging markets such as Africa and Latin America.

Conflits sur un navire de croisière : étude descriptive

Cette étude vise à comprendre les motifs qui peuvent s’avérer source de conflits dans une situation où il est le plus inattendu : les navires de croisières. Nous analysons les constructions de la propagande de vente de croisières avec l’utilisation des mythes marins. Nous nous questionnons ensuite sur la relation entre l’être humain et la mer à partir de la grande diversité mythologique entourant celle-ci ainsi que l’expérience empirique de la vie sur un navire de croisière (également sur un paquebot, cargo et bateau militaire). Dans ce contexte touristique, nous abordons le thème de la rencontre de l’Autre : l’Autre étant les personnes habitant les destinations visitées, les touristes, et principalement, les employés sur le navire responsables du service à la clientèle. Enfin, nous analysons plusieurs conflits représentatifs vécus à bord d’une croisière afin de comprendre les structures conflictuelles ; l’espace, la subordination, les jeux de rôle, les classes sociales, etc.

Résultats des cupules de grand diamètre dans les reprises d’arthroplastie totale de hanche : suivi minimum de deux ans.

La révision d’arthroplastie de la hanche en cas d’important déficit osseux acétabulaire peut être difficile. Les reconstructions avec cupule de très grand diamètre ou cupule « jumbo » (≥ 62 mm chez la femme et ≥ 66 mm chez l’homme) sont une option thérapeutique. Nous voulions évaluer la préservation et la restauration du centre de rotation de la hanche reconstruite en la comparant au coté controlatéral sain ou selon les critères de Pierchon et al. Nous voulions également évaluer la stabilité du montage à un suivi d’au moins 2 ans. Il s’agissait de 53 cas consécutifs de révision acétabulaire pour descellement non septique avec implantation d’une cupule jumbo sans ciment à l’Hôpital Maisonneuve-Rosemont. Le déficit osseux évalué selon la classification de Paprosky et al. Les cupules implantées avaient un diamètre moyen de 66 mm (62-81) chez les femmes et 68 mm (66-75) chez les hommes. L’allogreffe osseuse morcelée et massive était utilisée dans 34 et dans 14 cas respectivement. La cupule a été positionnée avec un angle d’inclinaison moyen de 41.3° (26.0-53.0). Le centre de rotation de la hanche reconstruite a été jugé satisfaisant dans 78% de cas sur l'axe médiolatéral, 71% sur l'axe craniopodal et amélioré dans 27% dans cet axe. Au recul moyen radiologique de 84.0 mois (24.0-236.4) et clinique de 91.8 mois (24.0 – 241.8): 6 cas étaient décédés, 3 perdus au suivi. On a observé le descellement radiologique dans un 1 cas, la luxation récidivante dans 5 cas et l’infection dans 4 cas. Le retrait de la cupule a été effectué dans 2 cas pour infection. L’ostéointégration des greffons osseux était complète dans tous les cas sauf 3. Les scores cliniques étaient pour le HHS de 82 +/-17, le WOMAC de 86 +/- 14 et le SF-12 physique de 46 +/- 12 et mental 53 +/-13. La cupule jumbo peut être considérée comme un moyen fiable pour gérer le déficit osseux dans les révisions acétabulaires. Elle permet de conserver ou d’améliorer la position du centre de rotation physiologique de la hanche. La fixation sans ciment favorise l’ostéointégration de la cupule et permet une stabilité à moyen terme. Le taux de complications est comparable ou inférieur à d'autres procédures de reconstruction.

Vibrational spectroscopic studies of FeClMoO4, Na2MoO4 and Na2MoO4·2H2O:D2O

FTIR and Raman spectra of FeClMoO4 single crystal and polycrystalline Na2MoO4, Na2MoO4·2H2O and Na2MoO4·2D2O are recorded and analysed. The band positions for different modes suggest that MoO4 tetrahedron is more distorted in FeClMoO4. The larger splitting observed for the bending modes and partial retention of degeneracy of the asymmetric stretching mode indicate that angular distortion is greater than liner distortion in MoO4 2 ion in FeClMoO4 confirming x-ray data. The non-appearance of the n1 and n2 modes in the IR and partial retention of the degeneracies of various modes show that MoO4 2 ion retains Td symmetry in Na2MoO4. Wavenumber values of the n1 mode indicate that the distortion of MoO4 tetrahedra in the four crystals are in the order FeClMoO4\ Na2MoO4·2H2O\Na2MoO4·2D2O\Na2MoO4. The water bands suggest the presence of two crystallographically distinct water molecules in Na2MoO4·2H2O. They form strong hydrogen bonds

Técnicas de reabilitação sem abertura de vala de redes de drenagem de águas residuais

O objectivo da presente dissertação consiste na apresentação de várias técnicas de reabilitação de redes de drenagem de águas residuais sem necessidade de abertura de vala. Para esse efeito efectuou-se um levantamento das técnicas de reabilitação de colectores sem abertura de vala actualmente existente no mercado, tendo-se identificado cinco técnicas diferentes, organizadas em dois grandes grupo: Técnicas de encamisamento (i.e., encamisamento pontual - «short liner» e contínuo com manga de fibras de feltro ou com manga de fibras de vidro) e técnicas de entubamento (i.e., entubamento simples - «sliplining» e com rebentamento por destruição da tubagem existente). As técnicas de reabilitação que foram desenvolvidas foram aplicadas a dois casos de estudo diferentes: um encamisamento contínuo com mangas de fibra de vidro (cura por radiação ultravioleta) para renovar o Emissário da Cadaveira, e um entubamento com rebentamento com tubos modelares pelo processo dinâmico, primeiro caso de entubamento realizado em Portugal para renovar um troço da rede de drenagem doméstica do novo Hospital de Cascais. A apresentação de casos de estudo foi fundamental para perceber o funcionamento das técnicas de reabilitação, e deu um aspecto técnico, essencial, a esta dissertação.

Can retired galaxies mimic active galaxies? Clues from the Sloan Digital Sky Survey

The classification of galaxies as star forming or active is generally done in the ([O III]/H beta, [N II]/H alpha) plane. The Sloan Digital Sky Survey (SDSS) has revealed that, in this plane, the distribution of galaxies looks like the two wings of a seagull. Galaxies in the right wing are referred to as Seyfert/LINERs, leading to the idea that non-stellar activity in galaxies is a very common phenomenon. Here, we argue that a large fraction of the systems in the right wing could actually be galaxies which stopped forming stars. The ionization in these `retired` galaxies would be produced by hot post-asymptotic giant branch stars and white dwarfs. Our argumentation is based on a stellar population analysis of the galaxies via our STARLIGHT code and on photoionization models using the Lyman continuum radiation predicted for this population. The proportion of LINER galaxies that can be explained in such a way is, however, uncertain. We further show how observational selection effects account for the shape of the right wing. Our study suggests that nuclear activity may not be as common as thought. If retired galaxies do explain a large part of the seagull`s right wing, some of the work concerning nuclear activity in galaxies, as inferred from SDSS data, will have to be revised.