Cure processing modeling and cure cycle simulation of epoxy-terminated poly(phenylene ether ketone). V: Estimation of temperature distribution during cure process

A numerical method to estimate temperature distribution during the cure of epoxy-terminated poly(phenylene ether ketone) (E-PEK)-based composite is suggested. The effect of the temperature distribution on the selection of cure cycle is evaluated using a suggested alternation criterion. The effect of varying heating rate and thickness on the temperature distribution, viscosity distribution and distribution of the extent of cure reaction are discussed based on the combination of the here-established temperature distribution model and the previously established curing kinetics model and chemorheological model. It is found that, for a thin composite (<=10mm) and low heating rate (<=2.5K/min), the effect of temperature distribution on cure cycle and on the processing window for pressure application can be neglected. Low heating rate is of benefit to reduce the temperature gradient. The processing window for pressure application becomes narrower with increasing thicknesses of composite sheets. The validity of the temperature distribution model and the modified processing window is evaluated through the characterization of mechanical and physical properties of E-PEK-based composite fabricated according to different temperature distribution conditions.

CHARACTERIZATION OF BLENDS OF POLYPROPYLENE WITH A SEMIRIGID LIQUID-CRYSTAL COPOLYESTER

Blends with a liquid-crystal polymers (LCP) as one component show, in general, very interesting properties. Reduction of shear visocity and improvement of mechanical properties are very remarkable. High melting temperatures and high costs of the LCP limit the use of these blends. A new class of thermotropic LCPs with flexible spaces, with relatively low melting temperatures, can overcome the first problem. In this work, rheological and mechanical properties of blends of polypropylene with low contents of this LCP are presented. Torque during extrusion and viscosity decrease with LCP content. Elastic modulus is remarkably increased when the LCP phase is oriented.

西秦岭新生代火山岩中的地幔捕虏体和捕虏晶研究

Western Qinling, a conjunction region of the North China Craton, the Yangtze Craton and the Tibetan Plateau, has very complicated history of geologic and tectonic evolution. Previous studies mainly focus on tectonics and petrology of volcanic rocks in the western Qinling. Therefore, little is known about the Cenozoic lithospheric mantle beneath the western Qinling. Mafic, ultramafic and/or alkaline volcanic rocks and their entrained mantle peridotitic xenoliths and xenocrysts are known as samples directly from the lithospheric mantle. Their petrological and geochemical characteristics can reflect the nature and deep processes of the lithospheric mantle. Cenozoic volcanic rocks in the western Qinling contain abundant mantle xenoliths and xenocrysts, which provide us an opportunity to probe the lithospheric mantle beneath this region and a new dimension to insight into geologic evolution. Cenozoic volcanic rocks (7-23 Ma) from the western Qinling are sparsely distributed in the Lixian-Dangchang-Xihe Counties, Gansu Province, China. Volcanic rocks contain plenty of mantle-derived xenoliths, including spinel lherzolites with subordinate wehrlite, dunite, olivine websterite, clinopyroxenite and garnet lherzolite, and few olivine, clinopyroxene and spinel xenocrysts. These peridotitic xenoliths show clear deformed textures and their major minerals show excellent orientation. Thus, these peridotites are typical deformed peridotites. Olivine xenocrysts have clearly-zoned textures. The peridotitic xenoliths can be divided into two groups based on their compositions, namely, the H-type and L-type. The H-type peridotites are characterized by high Fo (>90) in olivines in which fine-grained ones have higher Fo than the coarse grains, low CaO (<20 %) in clinopyroxenes, high Cr# (>40) in spinels and high equilibration temperatures. They may represent the refractory lithospheric mantle. In contrast, the L-type peridotites contain low Fo (<90) olivines (with lower Fo in fine-grained olivines), high CaO (>20 %) clinopyroxenes, low Cr# (<20) spinels and low equilibration temperatures. They experienced low degree of partial melting. The Cenozoic lithospheric mantle beneath the western Qinling was refractory in major element compositions based on the mineral compositions of xenoliths and xenocrysts and experienced complicated deep processes. The lithospheric mantle was modified by shear deformation due to the diapirism of asthenosphere and strong tectonic movements including the collision between North China Craton and Yangze Craton and the uplift of Tibetan Plateau, and then underwent metasomatism with a hydrous, Na, Ti and Cr enriched melt.

塔里木盆地塔北、塔中地区早古生代白云岩形成机理

In Tarim Basin, extensive carbonates of Lower Paleozoic occur, in which thick Cambrian and Lower Ordovician dolostones are widespread and show a potential perspective in hydrocarbon exploration. So they are viewed as an important target for exploration. Tarim Basin is a poly phase composite basin, which underwent multiphase tectonic modification and volcanic activities; these exerted significant influences on the basin-fills and basin fluid evolution, thereby the diagenetic history, particularly on the deep-buried Lower Paleozoic dolostones. Referring to the classification of dolomite texture proposed by Gregg & Sibley (1984) and Sibley & Gregg (1987). In view of crystal size, crystal shape, crystal surface and contact relation, eight genetic textures of dolomite crystals are identified, based on careful petrographic examinatoins. These textures include: 1) micritic dolomite; 2) relict mimetic dolomite; 3)finely crystalline, planar-e(s), floating dolomite; 4)finely crystalline, planar-e(s) dolomite; 5) finely-coarse crystalline, nonplanar-a dolomite; 6)coarse crystalline, nonplanar saddle dolomite; 7) finely-medium crystalline, planar-e(s) dolomite cement; 8) coarse crystalline, nonplanar saddle dolomite cement, in which the former six textures occurs as in matrix, the latter two in the cements. Detailed geochemistry analysis is carried out on the basis of genetic textures of dolomite and related minerals such as quartz and calcite. The result showed that the calcite has the highest average content in Sr, which can be sorted into two groups; micritic dolomite has the highest average content in Sr among all kinds of dolomites; the REE patterns of all kinds of dolomites is similar to those of marine limestone samples. Saddle dolomite cement has δ13C values from -2.44‰ to 1.27‰ PDB, and δ18O values from -13.01‰ to -5.12‰ PDB, which partially overlap with those of matrix dolomite (δ13C values from -2.83‰ to 2.01‰ PDB, δ18O values from -10.63‰ to -0.85‰ PDB). Saddle dolomite cement has 87Sr/86Sr ratios from 0.7086 to 0.7104, which totally overlap with those of matrix dolomite (0.7084 ~ 0.7116). Compared with saddle dolomite derived from other basins all over the world, the saddle dolomites of Tarim Basin have similar δ13C, δ18O and 87Sr/86Sr ratios values with those of matrix dolomite. This scenario reflects the unusual geological setting and special dolomitizing liquid of Tarim Basin. The values of δ18O, δ13C and 87Sr/86Sr ratios of calcite also can be sorted out two groups, which may been resulted from the one stage of extensive uplift of Tarim Basin from Mesozoic to Cenozoic. Fluid inclusion microthermometry data of the diagenetic mineral indicates that matrix dolomite has relatively low homogenization temperatures (Th) of 80～105oC and salinities of 12.3％ (wt% NaCl equivalent); saddle dolomite has highest Th values, which concentrate in 120～160oC and salinities of 13.5～23.7％ (wt% NaCl equivalent); quartz has relatively low Th of 135～155oC and salinities of 17.8～22.5％ (wt% NaCl equivalent); calcite has relatively low Th of 121～159.5oC and salinities of 1.4～17.5％ (wt% NaCl equivalent). These data suggest that the saddle dolomites could have formed in thermal brine fluids. Based on comprehensive petrographical study, detailed geochemistry and fluid inclusion microthermometry analysis on Lower Paleozoic dolomite of Tarim Basin, three types of dolomitisation mechanism are proposed: Penecontemporaneous dolomitisation (Sabkha dolomitisation & Reflux dolomitisation); Burial dolomitisation (shallow-intermediate burial dolomitisation & Deep burial dolomitisation ); Hydrothermal cannibalized dolomitisation. In view of host-specified occurrences of hydrothermal dolomite, the low abundance of saddle dolomite and high geochemical similarities between saddle dolomite and host dolomite, as well as highest Th and high salinities , the hydrothermal dolomite in Tarim Basin is thus unique, which could have been precipitated in modified fluid in the host dolomite through intraformational thermal fluid cannibalization of Mg ions from the host. This scenario is different from the cases that large scale dolomitizing fluid migration took place along the fluid pathways where abundant saddle dolomite precipitated. Detailed observations on 180 petrographic and 60 casting thin sections show original pores in Lower Paleozoic dolomite were almost died out by complicated diagenetic process after a long time geologic evolution. On the other hand, deep-buried dolomite reservoirs is formed by tectonic and hydrothermal reforming on initial dolomites. Therefore, the distribution of structure-controlled hydrothermal dolomite reservoirs is predicted in Tabei and Tazhong Area of Tarim Basin based on the geophysical data.

The Role of Tool/Sheet Contact in Plug-Assisted Thermoforming.

Plug-assisted thermoforming produces a wide range of polymer products through a combination of deformation by air pressure and contact with tool surfaces. In this paper the role of tool/sheet contact in determining the process output is investigated. A combination of thermoforming, friction and heat transfer tests were carried out on common tool and sheet materials. The results show that the typical friction coefficients for the material combinations are within the range 0.1 to 0.3, but the values rise sharply on approaching thermoforming temperatures. Thermal imaging tests demonstrate that all of the plug materials significantly cool the heated sheet on contact, even over very short periods of time. The temperature of the plug is very important. At low plug temperatures heat transfer effects predominate, whereas at high plug temperatures friction effects predominate. A plug temperature of approximately 100oC balances these effects and creates the most effective material distribution.

The energetics of huddling in two species of mole-rat (Rodentia: Bathyergidae)

Small rodents with a large surf ace-area-to-volume ratio and a high thermal conductance are likely to experience conditions where they have to expend large: amounts of energy in order to maintain a constant body temperature at low ambient temperatures. The survival of small rodents is thus dependent on their ability to reduce heat loss and increase heat production at low ambient temperatures. Two such animals are the social subterranean rodents Cryptomys damarensis (the Damaraland mole-rat) and Cryptomys hottentotus natalensis (the Natal mole-rat). This study examined the energy savings associated with huddling as a behavioural thermoregulatory mechanism to conserve energy in both these species. Individual oxygen consumption (VO2) was measured in groups ranging in size from one to 15 huddling animals for both species at ambient temperatures of 14, 18, 22, 26 and 30 degrees C. Savings in energy (VO2) were then compared between the two species. Significant differences in VO2 (p

Electronic states and spin-forbidden cooling transitions of AlH and AlF

The feasibility of laser cooling AlH and AlF is investigated using ab initio quantum chemistry. All the electronic states corresponding to the ground and lowest two excited states of the Al atom are calculated using multi-reference configuration interaction (MRCI) and the large AV6Z basis set for AlH. The smaller AVQZ basis set is used to calculate the valence electronic states of AlF. Theoretical Franck-Condon factors are determined for the A(1)Pi -> X(1)Sigma(+) transitions in both radicals and found to agree with the highly diagonal factors found experimentally, suggesting computational chemistry is an effective method for screening suitable laser cooling candidates. AlH does not appear to have a transition quite as diagonal as that in SrF (which has been laser cooled) but the A(1)Pi -> X(1)Sigma(+) transition transition of AlF is a strong candidate for cooling with just a single laser, though the cooling frequency is deep in the UV. Furthermore, the a (3)Pi -> X(1)Sigma(+) transitions are also strongly diagonal and in AlF is a practical method for obtaining very low final temperatures around 3 mu K.

Climatic signals in the life histories of insects:the distribution and abundance of heather psyllids (Strophingia spp.) in the UK

1. The population density and age structure of two species of heather psyllid Strophingia ericae and Strophingia cinereae, feeding on Calluna vulgaris and Erica cinerea, respectively, were sampled using standardized methods at locations throughout Britain. Locations were chosen to represent the full latitudinal and altitudinal range of the host plants.

2. The paper explains how spatial variation in thermal environment, insect life-history characteristics and physiology, and plant distribution, interact to provide the mechanisms that determine the range and abundance of Strophingia spp.

3. Strophingia ericae and S. cinereae, despite the similarity in the spatial distribution patterns of their host plants within Britain, display strongly contrasting geographical ranges and corresponding life-history strategies. Strophingia ericae is found on its host plant throughout Britain but S. cinereae is restricted to low elevation sites south of the Mersey-Humber line and occupies only part of the latitudinal and altitudinal range of its host plant. There is no evidence to suggest that S. ericae has reached its potential altitudinal or latitudinal limit in the UK, even though its host plant appears to reach its altitudinal limit.

4. There was little difference in the ability of the two Strophingia spp. to survive shortterm exposure to temperatures as low as - 15 degrees C and low winter temperatures probably do not limit distribution in S. cinereae.

5. Population density of S. ericae was not related to altitude but showed a weak correlation with latitude. The spread of larval instars present at a site, measured as an index of instar homogeneity, was significantly correlated with a range of temperature related variables, of which May mean temperature and length of growing season above 3 degrees C (calculated using the Lennon and Turner climatic model) were the most significant. Factor analysis did not improve the level of correlation significantly above those obtained for single climatic variables. The data confirmed that S. ericae has a I year life cycle at the lowest elevations and a 2 year life cycle at the higher elevations. However, there was no evidence, as previously suggested, for an abrupt change from a one to a 2 year life cycle in S. ericae with increasing altitudes or latitudes.

6. By contrast with S. ericae, S. cinereae had an obligatory 1 year life cycle, its population decreased with altitude and the index of instar homogeneity showed little correlation with single temperature variables. Moreover, it occupied only part of the range of its host plant and its spatial distribution in the UK could be predicted with 96% accuracy using selected variables in discriminant analysis.

7. The life histories of the congeneric heather psyllids reflect adaptations that allow them to exploit host plants with different distributions in climatic and thereby geographical space. Strophingia ericae has the flexible life history that enables it to exploit C. vulgaris throughout its European boreal temperate range. Strophingia cinereae has a less flexible life history and is adapted for living on an oceanic temperate host. While the geographic ranges of the two Strophingia spp. overlap within the UK, the psyllids appear to respond differently to variation in their thermal environment.

Developmental, morphological, and behavioural plasticity in the reproductive strategies of stink bugs and their egg parasitoids

L’environnement façonne la physiologie, la morphologie et le comportement des organismes par l’entremise de processus écologiques et évolutifs complexes et multidimensionnels. Le succès reproducteur des animaux est déterminé par la valeur adaptative d’un phénotype dans un environnement en modification constante selon une échelle temporelle d’une à plusieurs générations. De plus, les phénotypes sont façonnés par l’environnement, ce qui entraine des modifications adaptatives des stratégies de reproduction tout en imposant des contraintes. Dans cette thèse, considérant des punaises et leurs parasitoïdes comme organismes modèles, j’ai investigué comment plusieurs types de plasticité peuvent interagir pour influencer la valeur adaptative, et comment la plasticité des stratégies de reproduction répond à plusieurs composantes des changements environnementaux (qualité de l’hôte, radiation ultraviolette, température, invasion biologique). Premièrement, j’ai comparé la réponse comportementale et de traits d’histoire de vie à la variation de taille corporelle chez le parasitoïde Telenomus podisi Ashmead (Hymenoptera : Platygastridae), démontrant que les normes de réaction des comportements étaient plus souvent positives que celles des traits d’histoires de vie. Ensuite, j’ai démontré que la punaise prédatrice Podisus maculiventris Say (Hemiptera : Pentatomidae) peut contrôler la couleur de ses œufs, et que la pigmentation des œufs protège les embryons du rayonnement ultraviolet; une composante d’une stratégie complexe de ponte qui a évoluée en réponse à une multitude de facteurs environnementaux. Puis, j’ai testé comment le stress thermique affectait la dynamique de la mémoire du parasitoïde Trissolcus basalis (Wollaston) (Hymenoptera : Platygastridae) lors de l’apprentissage de la fiabilité des traces chimiques laissées par son hôte. Ces expériences ont révélé que des températures hautes et basses prévenaient l’oubli, affectant ainsi l’allocation du temps passé par les parasitoïdes dans des agrégats d’hôtes contenant des traces chimiques. J’ai aussi développé un cadre théorique général pour classifier les effets de la température sur l’ensemble des aspects comportementaux des ectothermes, distinguant les contraintes des adaptations. Finalement, j’ai testé l’habileté d’un parasitoïde indigène (T. podisi) à exploiter les œufs d’un nouveau ravageur invasif en agriculture, Halyomorpha halys Stål (Hemiptera : Pentatomidae). Les résultats ont montré que T. podisi attaque les œufs de H. halys, mais qu’il ne peut s’y développer, indiquant que le ravageur invasif s’avère un « piège évolutif » pour ce parasitoïde. Cela pourrait indirectement bénéficier aux espèces indigènes de punaises en agissant comme un puits écologique de ressources (œufs) et de temps pour le parasitoïde. Ces résultats ont des implications importantes sur la réponse des insectes, incluant ceux impliqués dans les programmes de lutte biologique, face aux changements environnementaux.

RF magnetron sputtered perovskite oxide electrodes for Ferroelectric RAM

The main objective of this thesis work is to optimize the growth conditions for obtaining crystalline and conducting Lao.5Sro.5Co03 (LSCO) and Lao.5Sro.5Coo.5.5Nio.5O3 (LSCNO) thin films at low processing temperatures. The films are prepared by radio frequency magnetron sputtering under various deposition conditions. The thin films were used as electrodes for the fabrication of ferroelectric capacitors using BaO.7SrO.3 Ti03 (BST) and PbZro.52 Tio.4803 (PZT). The structural and transport properties of the La1_xSrxCo03 and Lao.5Sro.5Co1_xNix03 are also investigated. The characterization of the bulk and the thin films were performed using different tools. A powder X-ray diffractometer was used to analyze the crystalline nature of the material. The transport properties were investigated by measuring the temperature dependence of resistivity using a four probe technique. The magnetoresistance and thermoelectric power were also used to investigate the transport properties. Atomic force microscope was used to study the surface morphology and thin film roughness. The ferroelectric properties of the capacitors were investigated using RT66A ferroelectric tester.

Optimization of Two Stage Process for the Growth of In2S3 , CuInSe2 and CuIn (Sel-xSx)2Thin Films for Solar Cell Application

Two stage processes consisting of precursor preparation by thermal evaporation followed by chalcogenisation in the required atmosphere is found to be a feasible technique for the PV materials such as n-Beta In2S3, p-CulnSe2, p-CulnS2 and p-CuIn(Sel_xSx)2. The growth parameters such as chalcogenisation temperature and duration of chalcogenisation etc have been optimised in the present study.Single phase Beta-In2S3 thin films can be obtained by sulfurising the indium films above 300°C for 45 minutes. Low sulfurisation temperatures required prolonged annealing after the sulfurisation to obtain single phase Beta-1n2S3, which resulted in high material loss. The maximum band gap of 2.58 eV was obtained for the nearly stoichiometric Beta-In2S3 film which was sulfurised at 350°C. This wider band gap, n type Beta-In2S3 can be used as an alternative to toxic CdS as window layer in photovoltaics .The systematic study on the structural optical and electrical properties of CuInSe2 films by varying the process parameters such as the duration of selenization and the selenization temperature led to the conclusion that for the growth of single-phase CuInSe2, the optimum selenization temperature is 350°C and duration is 3 hours. The presence of some binary phases in films for shorter selenization period and lower selenization temperature may be due to the incomplete reaction and indium loss. Optical band gap energy of 1.05 eV obtained for the films under the optimum condition.In order to obtain a closer match to the solar spectrum it is desirable to increase the band gap of the CulnSe2 by a few meV . Further research works were carried out to produce graded band gap CuIn(Se,S)2 absorber films by incorporation of sulfur into CuInSe2. It was observed that when the CulnSe2 prepared by two stage process were post annealed in sulfur atmosphere, the sulfur may be occupying the interstitial positions or forming a CuInS2 phase along with CuInSe2 phase. The sulfur treatment during the selenization process OfCu11 ln9 precursors resulted in Culn (Se,S)2 thin films. A band gap of 1.38 eV was obtained for the CuIn(Se,S)2.The optimised thin films n-beta 1n2S3, p-CulnSe2 and p-Culn(Sel-xSx)2 can be used for fabrication of polycrystalline solar cells.

Doped sodium aluminium hydrides as hydrogen storage materials: characterizations and mechanistic insights

The dehydriding and rehydriding of sodium aluminium hydride, NaAlR4, is kinetically enhanced and rendered reversible in the solid state upon doping with a small amount of catalyst species, such as titanium, zirconium or tin. The catalyst doped hydrides appear to be good candidates for development as hydrogen carriers for onboard proton exchange membrane (PEM) fuel cells because of their relatively low operation temperatures (120-150 degrees C) and high hydrogen carrying capacities (4-5 wt.%). However, the nature of the active catalyst species and the mechanism of catalytic action are not yet known. In particular, using combinations of Ti and Sri compounds as dopants, a cooperative catalyst effect of the metals Ti and Sn in enhancing the hydrogen uptake and release kinetics is hereby reported. In this paper, characterization techniques including XRD, XPS, TEM, EDS and SEM have been applied on this material. The results suggest that the solid state phase changes during the hydriding and dehydriding processes are assisted through the interaction of a surface catalyst. A mechanism is proposed to explain the catalytic effect of the Sn/Ti double dopants on this hydride.

Groundwater residence time distributions in peatlands: implications for peat decomposition and accumulation

Peat soils consist of poorly decomposed plant detritus, preserved by low decay rates, and deep peat deposits are globally significant stores in the carbon cycle. High water tables and low soil temperatures are commonly held to be the primary reasons for low peat decay rates. However, recent studies suggest a thermodynamic limit to peat decay, whereby the slow turnover of peat soil pore water may lead to high concentrations of phenols and dissolved inorganic carbon. In sufficient concentrations, these chemicals may slow or even halt microbial respiration, providing a negative feedback to peat decay. We document the analysis of a simple, one-dimensional theoretical model of peatland pore water residence time distributions (RTDs). The model suggests that broader, thicker peatlands may be more resilient to rapid decay caused by climate change because of slow pore water turnover in deep layers. Even shallow peat deposits may also be resilient to rapid decay if rainfall rates are low. However, the model suggests that even thick peatlands may be vulnerable to rapid decay under prolonged high rainfall rates, which may act to flush pore water with fresh rainwater. We also used the model to illustrate a particular limitation of the diplotelmic (i.e., acrotelm and catotelm) model of peatland structure. Model peatlands of contrasting hydraulic structure exhibited identical water tables but contrasting RTDs. These scenarios would be treated identically by diplotelmic models, although the thermodynamic limit suggests contrasting decay regimes. We therefore conclude that the diplotelmic model be discarded in favor of model schemes that consider continuous variation in peat properties and processes.

Global biomass burning: a synthesis and review of Holocene paleofire records and their controls.

We synthesize existing sedimentary charcoal records to reconstruct Holocene fire history at regional, continental and global scales. The reconstructions are compared with the two potential controls of burning at these broad scales – changes in climate and human activities – to assess their relative importance on trends in biomass burning. Here we consider several hypotheses that have been advanced to explain the Holocene record of fire, including climate, human activities and synergies between the two. Our results suggest that 1) episodes of high fire activity were relatively common in the early Holocene and were consistent with climate changes despite low global temperatures and low levels of biomass burning globally; 2) there is little evidence from the paleofire record to support the Early Anthropocene Hypothesis of human modification of the global carbon cycle; 3) there was a nearly-global increase in fire activity from 3 to 2 ka that is difficult to explain with either climate or humans, but the widespread and synchronous nature of the increase suggests at least a partial climate forcing; and 4) burning during the past century generally decreased but was spatially variable; it declined sharply in many areas, but there were also large increases (e.g., Australia and parts of Europe). Our analysis does not exclude an important role for human activities on global biomass burning during the Holocene, but instead provides evidence for a pervasive influence of climate across multiple spatial and temporal scales.

Maintenance of the African easterly jet

The maintenance of the African easterly jet (AEJ) has been examined using a zonally symmetric general circulation model with simple parametrizations. It is shown that the AEJ is maintained in association with two diabatically forced meridional circulations: one associated with surface fluxes and dry convection in the Saharan heat-low region and one associated with deep moist convection in the intertropical convergence zone equatorward of this. the heat-low heating, which reaches the height of the AEJ around 700 mb, is particularly important in maintaining the AEJ and its associated meridional gradients in potential vorticity. It is concluded that the mean observed AEJ results from a combination of the diabatically forced meridional circulations which maintain it and easterly waves which weaken it.