Investigation of MEMS inertial sensors and aircraft dynamic models in global positioning system integrity monitoring for approaches with vertical guidance

An Approach with Vertical Guidance (APV) is an instrument approach procedure which provides horizontal and vertical guidance to a pilot on approach to landing in reduced visibility conditions. APV approaches can greatly reduce the safety risk to general aviation by improving the pilot’s situational awareness. In particular the incidence of Controlled Flight Into Terrain (CFIT) which has occurred in a number of fatal air crashes in general aviation over the past decade in Australia, can be reduced. APV approaches can also improve general aviation operations. If implemented at Australian airports, APV approach procedures are expected to bring a cost saving of millions of dollars to the economy due to fewer missed approaches, diversions and an increased safety benefit. The provision of accurate horizontal and vertical guidance is achievable using the Global Positioning System (GPS). Because aviation is a safety of life application, an aviation-certified GPS receiver must have integrity monitoring or augmentation to ensure that its navigation solution can be trusted. However, the difficulty with the current GPS satellite constellation alone meeting APV integrity requirements, the susceptibility of GPS to jamming or interference and the potential shortcomings of proposed augmentation solutions for Australia such as the Ground-based Regional Augmentation System (GRAS) justifies the investigation of Aircraft Based Augmentation Systems (ABAS) as an alternative integrity solution for general aviation. ABAS augments GPS with other sensors at the aircraft to help it meet the integrity requirements. Typical ABAS designs assume high quality inertial sensors to provide an accurate reference trajectory for Kalman filters. Unfortunately high-quality inertial sensors are too expensive for general aviation. In contrast to these approaches the purpose of this research is to investigate fusing GPS with lower-cost Micro-Electro-Mechanical System (MEMS) Inertial Measurement Units (IMU) and a mathematical model of aircraft dynamics, referred to as an Aircraft Dynamic Model (ADM) in this thesis. Using a model of aircraft dynamics in navigation systems has been studied before in the available literature and shown to be useful particularly for aiding inertial coasting or attitude determination. In contrast to these applications, this thesis investigates its use in ABAS. This thesis presents an ABAS architecture concept which makes use of a MEMS IMU and ADM, named the General Aviation GPS Integrity System (GAGIS) for convenience. GAGIS includes a GPS, MEMS IMU, ADM, a bank of Extended Kalman Filters (EKF) and uses the Normalized Solution Separation (NSS) method for fault detection. The GPS, IMU and ADM information is fused together in a tightly-coupled configuration, with frequent GPS updates applied to correct the IMU and ADM. The use of both IMU and ADM allows for a number of different possible configurations. Three are investigated in this thesis; a GPS-IMU EKF, a GPS-ADM EKF and a GPS-IMU-ADM EKF. The integrity monitoring performance of the GPS-IMU EKF, GPS-ADM EKF and GPS-IMU-ADM EKF architectures are compared against each other and against a stand-alone GPS architecture in a series of computer simulation tests of an APV approach. Typical GPS, IMU, ADM and environmental errors are simulated. The simulation results show the GPS integrity monitoring performance achievable by augmenting GPS with an ADM and low-cost IMU for a general aviation aircraft on an APV approach. A contribution to research is made in determining whether a low-cost IMU or ADM can provide improved integrity monitoring performance over stand-alone GPS. It is found that a reduction of approximately 50% in protection levels is possible using the GPS-IMU EKF or GPS-ADM EKF as well as faster detection of a slowly growing ramp fault on a GPS pseudorange measurement. A second contribution is made in determining how augmenting GPS with an ADM compares to using a low-cost IMU. By comparing the results for the GPS-ADM EKF against the GPS-IMU EKF it is found that protection levels for the GPS-ADM EKF were only approximately 2% higher. This indicates that the GPS-ADM EKF may potentially replace the GPS-IMU EKF for integrity monitoring should the IMU ever fail. In this way the ADM may contribute to the navigation system robustness and redundancy. To investigate this further, a third contribution is made in determining whether or not the ADM can function as an IMU replacement to improve navigation system redundancy by investigating the case of three IMU accelerometers failing. It is found that the failed IMU measurements may be supplemented by the ADM and adequate integrity monitoring performance achieved. Besides treating the IMU and ADM separately as in the GPS-IMU EKF and GPS-ADM EKF, a fourth contribution is made in investigating the possibility of fusing the IMU and ADM information together to achieve greater performance than either alone. This is investigated using the GPS-IMU-ADM EKF. It is found that the GPS-IMU-ADM EKF can achieve protection levels approximately 3% lower in the horizontal and 6% lower in the vertical than a GPS-IMU EKF. However this small improvement may not justify the complexity of fusing the IMU with an ADM in practical systems. Affordable ABAS in general aviation may enhance existing GPS-only fault detection solutions or help overcome any outages in augmentation systems such as the Ground-based Regional Augmentation System (GRAS). Countries such as Australia which currently do not have an augmentation solution for general aviation could especially benefit from the economic savings and safety benefits of satellite navigation-based APV approaches.

Sensitivity of the lane change test as a measure of in-vehicle system demand

The Lane Change Test (LCT) is one of the growing number of methods developed to quantify driving performance degradation brought about by the use of in-vehicle devices. Beyond its validity and reliability, for such a test to be of practical use, it must also be sensitive to the varied demands of individual tasks. The current study evaluated the ability of several recent LCT lateral control and event detection parameters to discriminate between visual-manual and cognitive surrogate In-Vehicle Information System tasks with different levels of demand. Twenty-seven participants (mean age 24.4 years) completed a PC version of the LCT while performing visual search and math problem solving tasks. A number of the lateral control metrics were found to be sensitive to task differences, but the event detection metrics were less able to discriminate between tasks. The mean deviation and lane excursion measures were able to distinguish between the visual and cognitive tasks, but were less sensitive to the different levels of task demand. The other LCT metrics examined were less sensitive to task differences. A major factor influencing the sensitivity of at least some of the LCT metrics could be the type of lane change instructions given to participants. The provision of clear and explicit lane change instructions and further refinement of its metrics will be essential for increasing the utility of the LCT as an evaluation tool.

Affordable housing solutions : affordable housing providers’ perspective

Accessibility to housing for low to moderate income groups in Australia has experienced a severe decline since 2002. On the supply side, the public sector has been reducing its commitment to the direct provision of public housing. Despite strong demand for affordable housing, limited supply has been generated by non-government housing providers. This paper identifies and discusses some current affordable housing solutions which have been developed by non-government housing providers to ameliorate the problem. This study utilises case studies generated from nineteen housing providers during in-depth interviews in South East Queensland in 2007-2008. The case studies are classified into four categories which relate to the nature of their product: affordable rental housing, mixed housing, affordable housing for people with special needs and low cost home ownership. Each category is discussed on the basis of the characteristics typical of that organisation of housing provider, their partnership arrangements and main target market. In addition, the special design and facilities required for people with special needs which include high care accommodation and aged care are highlighted. Finally, this study recommends offering a continuum of solutions to affordable housing for low income people by means of a rent-to-buy scheme.

Affordable housing solutions : affordable housing providers’ perspective

Accessibility to housing for low to moderate income groups in Australia has been experiencing a severe decline since 2002. On the supply side, the public sector has been reducing its commitment to the direct provision of public housing. Despite strong demand for affordable housing, limited supply has been generated by nongovernment housing providers. This paper identifies and discusses some current affordable housing solutions to ameliorate the problem which have been developed by non-government housing providers. This study utilises case studies generated from nineteen housing providers during indepth interviews in South East Queensland in 2007-2008. The case studies are classified into four categories which relate to the nature of their product: affordable rental housing, mixed housing, affordable housing for people with special needs and low cost home ownership. Each category is discussed on the basis of the characteristics typical of that organisation of housing provider, their partnership arrangements and main target market. In addition, the special design and facilities required for people with special needs which include high care accommodation and aged care are highlighted. Finally, this study recommends offering a continuum of solutions to affordable housing for low income people by means of a rent-to-buy scheme.

Service enhanced manufacturing in the building and construction product system

This report examines the involvement of manufacturers in value-adding through service-enhancement of product offerings. This focus has been prompted by:  emphasis in the knowledge-economy literature on the increasing role played by services in economic growth; and  recent analysis which suggests that the most dynamic sector of many economies is an integrated manufacturing-services sector (see Part One of this report). The report initially describes the emergence of an integrated manufacturing-services sector in the context of increasingly knowledge-based economic systems. Part Two reports on the results of a survey of manufacturers in the building and construction product system, investigating their involvement in service provision. Parts Three and Four present two case studies of exemplary manufacturers involved in adding value to their manufacturing operations through services offered on building and construction projects. The report examines manufacturers of materials, products, equipment and machinery used on building and construction projects. The two case study sections of the report, in part, focus on a major project undertaken by each of the manufacturers. This project element of activity is focussed on (as opposed to wholesale or retail supply), because this area of activity involves a broader array of service-enhancement mechanisms and more complex bundling of products and services.

Developing sustainable housing through building utilities and transport innovation

Sustainability concerns every citizen. Housing affordability and sustainable solutions are being highlighted in research and practice in many parts of the world. This paper discusses the development of a Commuter Energy and Building Utilities System (CEBUS) in sustainable housing projects as a means of bridging the gap between current median house pricing and target affordable house pricing for low income earners. Similar scales of sustainable housing development cannot be achieved through independent application of current best practice methods in ecologically sustainable development strategies or transit oriented development master plans. This paper presents the initial stage of research on first capital and ongoing utilities and transport cost savings available from these sustainable design methods. It also outlines further research and development of a CEBUS Dynamic Simulation Model and Conceptual Framework for the Australian property development and construction industry.

Understanding user differences in open-source workflow management system usage intentions

Open-source software systems have become a viable alternative to proprietary systems. We collected data on the usage of an open-source workflow management system developed by a university research group, and examined this data with a focus on how three different user cohorts – students, academics and industry professionals – develop behavioral intentions to use the system. Building upon a framework of motivational components, we examined the group differences in extrinsic versus intrinsic motivations on continued usage intentions. Our study provides a detailed understanding of the use of open-source workflow management systems in different user communities. Moreover, it discusses implications for the provision of workflow management systems, the user-specific management of open-source systems and the development of services in the wider user community.

The impact of infrastructure charges on new housing costs : an international comparison

Sourcing funding for the provision of new urban infrastructure has been a policy dilemma for governments around the world for decades. This is particularly relevant in high growth areas where new services are required to support swelling populations. Existing communities resist the introduction of new taxes to fund such infrastructure, hence the introduction of charges to the developer has flourished. The Australian infrastructure funding policy dilemmas are reflective of similar matters to some extent in the United Kingdom, and to a greater extent the United States of America. In these countries, infrastructure cost recovery policies have been in place since the 1940’s and 1970’s respectively. There is an extensive body of theoretical and empirical literature that discusses the passing on (to home buyers) or passing back (to the englobo land seller) of these increased infrastructure charges, and the corresponding impact on housing cost and supply. The purpose of this research is to examine the international evidence that suggests infrastructure charges contribute to increased house prices as well as reduced land supply. The paper concludes that whilst the theoretical work is largely consistent, the empirical research to date is inconclusive and further research is required into these impacts in Australia.

Study of the effectiveness of outrigger system for high-rise composite buildings for cyclonic region

The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.

Development and feasibility of a smartphone, ECG and GPS based system for remotely monitoring exercise in cardiac rehabilitation

Background Despite its efficacy and cost-effectiveness, exercise-based cardiac rehabilitation is undertaken by less than one-third of clinically eligible cardiac patients in every country for which data is available. Reasons for non-participation include the unavailability of hospital-based rehabilitation programs, or excessive travel time and distance. For this reason, there have been calls for the development of more flexible alternatives. Methodology and Principal Findings We developed a system to enable walking-based cardiac rehabilitation in which the patient's single-lead ECG, heart rate, GPS-based speed and location are transmitted by a programmed smartphone to a secure server for real-time monitoring by a qualified exercise scientist. The feasibility of this approach was evaluated in 134 remotely-monitored exercise assessment and exercise sessions in cardiac patients unable to undertake hospital-based rehabilitation. Completion rates, rates of technical problems, detection of ECG changes, pre- and post-intervention six minute walk test (6 MWT), cardiac depression and Quality of Life (QOL) were key measures. The system was rated as easy and quick to use. It allowed participants to complete six weeks of exercise-based rehabilitation near their homes, worksites, or when travelling. The majority of sessions were completed without any technical problems, although periodic signal loss in areas of poor coverage was an occasional limitation. Several exercise and post-exercise ECG changes were detected. Participants showed improvements comparable to those reported for hospital-based programs, walking significantly further on the post-intervention 6 MWT, 637 m (95% CI: 565–726), than on the pre-test, 524 m (95% CI: 420–655), and reporting significantly reduced levels of cardiac depression and significantly improved physical health-related QOL. Conclusions and Significance The system provided a feasible and very flexible alternative form of supervised cardiac rehabilitation for those unable to access hospital-based programs, with the potential to address a well-recognised deficiency in health care provision in many countries. Future research should assess its longer-term efficacy, cost-effectiveness and safety in larger samples representing the spectrum of cardiac morbidity and severity.

An ingenious decision support system for remote health monitoring of pregnant women

Maternal deaths have been a critical issue for women living in rural and remote areas. The need to travel long distances, the shortage of primary care providers such as physicians, specialists and nurses, and the closing of small hospitals have been problems identified in many rural areas. Some research work has been undertaken and a few techniques have been developed to remotely measure the physiological condition of pregnant women through sophisticated ultrasound equipment. There are numerous ways to reduce maternal deaths, and an important step is to select the right approaches to achieving this reduction. One such approach is the provision of decision support systems in rural and remote areas. Decision support systems (DSSs) have already shown a great potential in many health fields. This thesis proposes an ingenious decision support system (iDSS) based on the methodology of survey instruments and identification of significant variables to be used in iDSS using statistical analysis. A survey was undertaken with pregnant women and factorial experimental design was chosen to acquire sample size. Variables with good reliability in any one of the statistical techniques such as Chi-square, Cronbach’s á and Classification Tree were incorporated in the iDSS. The decision support system was developed with significant variables such as: Place of residence, Seeing the same doctor, Education, Tetanus injection, Baby weight, Previous baby born, Place of birth, Assisted delivery, Pregnancy parity, Doctor visits and Occupation. The ingenious decision support system was implemented with Visual Basic as front end and Microsoft SQL server management as backend. Outcomes of the ingenious decision support system include advice on Symptoms, Diet and Exercise to pregnant women. On conditional system was sent and validated by the gynaecologist. Another outcome of ingenious decision support system was to provide better pregnancy health awareness and reduce long distance travel, especially for women in rural areas. The proposed system has qualities such as usefulness, accuracy and accessibility.

Implementing an enhanced repository statistics system for QUT ePrints

Queensland University of Technology (QUT) was one of the first universities in Australia to establish an institutional repository. Launched in November 2003, the repository (QUT ePrints) uses the EPrints open source repository software (from Southampton) and has enjoyed the benefit of an institutional deposit mandate since January 2004. Currently (April 2012), the repository holds over 36,000 records, including 17,909 open access publications with another 2,434 publications embargoed but with mediated access enabled via the ‘Request a copy’ button which is a feature of the EPrints software. At QUT, the repository is managed by the library.QUT ePrints (http://eprints.qut.edu.au) The repository is embedded into a number of other systems at QUT including the staff profile system and the University’s research information system. It has also been integrated into a number of critical processes related to Government reporting and research assessment. Internally, senior research administrators often look to the repository for information to assist with decision-making and planning. While some statistics could be drawn from the advanced search feature and the existing download statistics feature, they were rarely at the level of granularity or aggregation required. Getting the information from the ‘back end’ of the repository was very time-consuming for the Library staff. In 2011, the Library funded a project to enhance the range of statistics which would be available from the public interface of QUT ePrints. The repository team conducted a series of focus groups and individual interviews to identify and prioritise functionality requirements for a new statistics ‘dashboard’. The participants included a mix research administrators, early career researchers and senior researchers. The repository team identified a number of business criteria (eg extensible, support available, skills required etc) and then gave each a weighting. After considering all the known options available, five software packages (IRStats, ePrintsStats, AWStats, BIRT and Google Urchin/Analytics) were thoroughly evaluated against a list of 69 criteria to determine which would be most suitable. The evaluation revealed that IRStats was the best fit for our requirements. It was deemed capable of meeting 21 out of the 31 high priority criteria. Consequently, IRStats was implemented as the basis for QUT ePrints’ new statistics dashboards which were launched in Open Access Week, October 2011. Statistics dashboards are now available at four levels; whole-of-repository level, organisational unit level, individual author level and individual item level. The data available includes, cumulative total deposits, time series deposits, deposits by item type, % fulltexts, % open access, cumulative downloads, time series downloads, downloads by item type, author ranking, paper ranking (by downloads), downloader geographic location, domains, internal v external downloads, citation data (from Scopus and Web of Science), most popular search terms, non-search referring websites. The data is displayed in charts, maps and table format. The new statistics dashboards are a great success. Feedback received from staff and students has been very positive. Individual researchers have said that they have found the information to be very useful when compiling a track record. It is now very easy for senior administrators (including the Deputy Vice Chancellor-Research) to compare the full-text deposit rates (i.e. mandate compliance rates) across organisational units. This has led to increased ‘encouragement’ from Heads of School and Deans in relation to the provision of full-text versions.

Health professionals’ perspectives on information provision for patients with brain tumours and their families

A significant number of patients diagnosed with primary brain tumours report unmet information needs. Using concept mapping methodology, this study aimed to identify strategies for improving information provision, and to describe factors that health professionals understood to influence their provision of information to patients with brain tumours and their families. Concept mapping is a mixed methods approach that uses statistical methods to represent participants’ perceived relationships between elements as conceptual maps. These maps, and results of associated data collection and analyses, are used to extract concepts involved in information provision to these patients. Thirty health professionals working across a range of neuro-oncology roles and settings participated in the concept mapping process. Participants rated a care coordinator as the most important strategy for improving brain tumour care, with psychological support as a whole rated as the most important element of care. Five major themes were identified as facilitating information provision: health professionals’ communication skills, style and attitudes; patients’ needs and preferences; perceptions of patients’ need for protection and initiative; rapport and continuity between patients and health professionals; and the nature of the health care system. Overall, health professionals conceptualised information provision as ‘individualised’, dependent on these interconnected personal and environmental factors.

Beyond the 'at risk' individual : housing and the eradication of poverty to prevent homelessness

The 2008 White Paper on Homelessness (Australian Government 2008) constitutes a watershed initiative outlining the future for Australian homelessness policy. This contemporary homelessness policy is diverse and it continues to unfold and evolve during implementation. Nevertheless, it is characterised by the explicit intention to move beyond the former crisis based system, and the espousal of achieving measurable outcomes of permanently ending homelessness (Australian Government 2008).

Australia's disabling income support system : tracing the history of the Australian disability income support system 1908 to 2007 : disablism, citizenship and the basic income proposal

The present study examined the historical basis of the Australian disability income support system from 1908 to 2007. Although designed as a safety net for people with a disability, the disability income support system within Australia has been highly targeted. The original eligibility criteria of "permanently incapacitated for work", medical criteria and later "partially capacitated for work" potentially contained ideological inferences that permeated across the time period. This represents an important area for study given the potential consequence for disability income support to marginalise people with a disability. Social policy and disability policy theorists, including Saunders (2007, Social Policy Research Centre [SPRC]) and Gibilisco (2003) have provided valuable insight into some of the effects of disability policy and poverty. Yet while these theorists argued for some form of income support they did not propose a specific form of income security for further exploration. Few studies have undertaken a comprehensive review of the history of disability income support within the Australian context. This thesis sought to redress these gaps by examining disability income support policy within Australia. The research design consisted of an in-depth critical historical-comparative policy analysis methodology. The use of critical historical-comparative policy analysis allowed the researcher to trace the construction of disability within the Australian disability income support policy across four major historical epochs. A framework was developed specifically to guide analysis of the data. The critical discourse analysis method helped to understand the underlying ideological dimensions that led to the predominance of one particular approach over another. Given this, the research purpose of the study centred on: i. Tracing the history of the Australian disability income support system. ii. Examining the historical patterns and ideological assumptions over time. iii. Exploring the historical patterns and ideological assumptions underpinning an alternative model (Basic Income) and the extent to which each model promotes the social citizenship of people with a disability. The research commitment to a social-relational ontology and the quest for social change centred on the idea that "there has to be a better way" in the provision of disability income support. This theme of searching for an alternative reality in disability income support policy resonated throughout the thesis. This thesis found that the Australian disability income support system is disabling in nature and generates categories of disability on the basis of ableness. From the study, ableness became a condition for citizenship. This study acknowledged that, in reality, income support provision reflects only one aspect of the disabling nature of society which requires redressing. Although there are inherent tensions in any redistributive strategy, the Basic Income model potentially provides an alternative to the Australian disability income support system, given its grounding in social citizenship. The thesis findings have implications for academics, policy-makers and practitioners in terms of developing better ways to understand disability constructs in disability income support policy. The thesis also makes a contribution in terms of promoting income support policies based on the rights of all people, not just a few.