High precision pressure sensors based on SAW devices in the GHz range

In this paper, an AlN/free-standing nanocrystalline diamond (NCD) system is proposed in order to process high frequency surface acoustic wave (SAW) resonators for sensing applications. The main problem of synthetic diamond is its high surface roughness that worsens the sputtered AlN quality and hence the device response. In order to study the feasibility of this structure, AlN films from 150 nm up to 1200 nm thick have been deposited on free-standing NCD. We have then analysed the influence of the AlN layer thickness on its crystal quality and device response. Optimized thin films of 300 nm have been used to fabricate of one-port SAW resonators operating in the 10–14 GHz frequency range. A SAW based sensor pressure with a sensibility of 0.33 MHz/bar has been fabricated.

Loss model for a high frequency and low load DC/DC synchronous buck converter

This work presents a behavioral-analytical hybrid loss model for a buck converter. The model has been designed for a wide operating frequency range up to 4MHz and a low power range (below 20W). It is focused on the switching losses obtained in the power MOSFETs. Main advantages of the model are the fast calculation time and a good accuracy. It has been validated by simulation and experimentally with one Ga, power transistor and two Si MOSFETs. Results show good agreement between measurements and the model.

Hybrid behavioral-analytical loss model for a high frequency and low load DC/DC buck converter

This work presents a behavioral-analytical hybrid loss model for a buck converter. The model has been designed for a wide operating frequency range up to 4MHz and a low power range (below 20W). It is focused on the switching losses obtained in the power MOSFETs. Main advantages of the model are the fast calculation time (below 8.5 seconds) and a good accuracy, which makes this model suitable for the optimization process of the losses in the design of a converter. It has been validated by simulation and experimentally with one GaN power transistor and three Si MOSFETs. Results show good agreement between measurements and the model

Análisis y diseño de un patrón de ruido térmico de 10 MHz a 26,5 GHz en tecnología coaxial

Esta Tesis Doctoral presenta las investigaciones y los trabajos desarrollados durante los años 2008 a 2012 para el análisis y diseño de un patrón primario de ruido térmico de banda ancha en tecnología coaxial. Para ubicar esta Tesis en su campo científico es necesario tomar conciencia de que la realización de mediciones fiables y trazables forma parte del sostenimiento del bienestar de una sociedad moderna y juega un papel crítico en apoyo de la competitividad económica, la fabricación y el comercio, así como de la calidad de vida. En el mundo moderno actual, una infraestructura de medición bien desarrollada genera confianza en muchas facetas de nuestra vida diaria, porque nos permite el desarrollo y fabricación de productos fiables, innovadores y de alta calidad; porque sustenta la competitividad de las industrias y su producción sostenible; además de contribuir a la eliminación de barreras técnicas y de dar soporte a un comercio justo, garantizar la seguridad y eficacia de la asistencia sanitaria, y por supuesto, dar respuesta a los grandes retos de la sociedad moderna en temas tan complicados como la energía y el medio ambiente. Con todo esto en mente se ha desarrollado un patrón primario de ruido térmico con el fin de aportar al sistema metrológico español un nuevo patrón primario de referencia capaz de ser usado para desarrollar mediciones fiables y trazables en el campo de la medida y calibración de dispositivos de ruido electromagnético de radiofrecuencia y microondas. Este patrón se ha planteado para que cumpla en el rango de 10 MHz a 26,5 GHz con las siguientes especificaciones: Salida nominal de temperatura de ruido aproximada de ~ 83 K. Incertidumbre de temperatura de ruido menor que ± 1 K en todo su rango de frecuencias. Coeficiente de reflexión en todo su ancho de banda de 0,01 a 26,5 GHz lo más bajo posible. Se ha divido esta Tesis Doctoral en tres partes claramente diferenciadas. La primera de ellas, que comprende los capítulos 1, 2, 3, 4 y 5, presenta todo el proceso de simulaciones y ajustes de los parámetros principales del dispositivo con el fin de dejar definidos los que resultan críticos en su construcción. A continuación viene una segunda parte compuesta por el capítulo 6 en donde se desarrollan los cálculos necesarios para obtener la temperatura de ruido a la salida del dispositivo. La tercera y última parte, capítulo 7, se dedica a la estimación de la incertidumbre de la temperatura de ruido del nuevo patrón primario de ruido obtenida en el capítulo anterior. Más concretamente tenemos que en el capítulo 1 se hace una exhaustiva introducción del entorno científico en donde se desarrolla este trabajo de investigación. Además se detallan los objetivos que se persiguen y se presenta la metodología utilizada para conseguirlos. El capítulo 2 describe la caracterización y selección del material dieléctrico para el anillo del interior de la línea de transmisión del patrón que ponga en contacto térmico los dos conductores del coaxial para igualar las temperaturas entre ambos y mantener la impedancia característica de todo el patrón primario de ruido. Además se estudian las propiedades dieléctricas del nitrógeno líquido para evaluar su influencia en la impedancia final de la línea de transmisión. En el capítulo 3 se analiza el comportamiento de dos cargas y una línea de aire comerciales trabajando en condiciones criogénicas. Se pretende con este estudio obtener la variación que se produce en el coeficiente de reflexión al pasar de temperatura ambiente a criogénica y comprobar si estos dispositivos resultan dañados por trabajar a temperaturas criogénicas; además se estudia si se modifica su comportamiento tras sucesivos ciclos de enfriamiento – calentamiento, obteniendo una cota de la variación para poder así seleccionar la carga que proporcione un menor coeficiente de reflexión y una menor variabilidad. En el capítulo 4 se parte del análisis de la estructura del anillo de material dieléctrico utilizada en la nota técnica NBS 1074 del NIST con el fin de obtener sus parámetros de dispersión que nos servirán para calcular el efecto que produce sobre el coeficiente de reflexión de la estructura coaxial completa. Además se realiza un estudio posterior con el fin de mejorar el diseño de la nota técnica NBS 1074 del NIST, donde se analiza el anillo de material dieléctrico, para posteriormente realizar modificaciones en la geometría de la zona donde se encuentra éste con el fin de reducir la reflexión que produce. Concretamente se estudia el ajuste del radio del conductor interior en la zona del anillo para que presente la misma impedancia característica que la línea. Y para finalizar se obtiene analíticamente la relación entre el radio del conductor interior y el radio de la transición de anillo térmico para garantizar en todo punto de esa transición la misma impedancia característica, manteniendo además criterios de robustez del dispositivo y de fabricación realistas. En el capítulo 5 se analiza el comportamiento térmico del patrón de ruido y su influencia en la conductividad de los materiales metálicos. Se plantean las posibilidades de que el nitrógeno líquido sea exterior a la línea o que éste penetre en su interior. En ambos casos, dada la simetría rotacional del problema, se ha simulado térmicamente una sección de la línea coaxial, es decir, se ha resuelto un problema bidimensional, aunque los resultados son aplicables a la estructura real tridimensional. Para la simulación térmica se ha empleado la herramienta PDE Toolbox de Matlab®. En el capítulo 6 se calcula la temperatura de ruido a la salida del dispositivo. Se parte del estudio de la aportación a la temperatura de ruido final de cada sección que compone el patrón. Además se estudia la influencia de las variaciones de determinados parámetros de los elementos que conforman el patrón de ruido sobre las características fundamentales de éste, esto es, el coeficiente de reflexión a lo largo de todo el dispositivo. Una vez descrito el patrón de ruido electromagnético se procede, en el capítulo 7, a describir los pasos seguidos para estimar la incertidumbre de la temperatura de ruido electromagnético a su salida. Para ello se utilizan dos métodos, el clásico de la guía para la estimación de la incertidumbre [GUM95] y el método de simulación de Monte Carlo. En el capítulo 8 se describen las conclusiones y lo logros conseguidos. Durante el desarrollo de esta Tesis Doctoral se ha obtenido un dispositivo novedoso susceptible de ser patentado, que ha sido registrado en la Oficina Española de Patentes y Marcas (O.E.P.M.) en Madrid, de conformidad con lo establecido en el artículo 20 de la Ley 11/1986, de 20 de Marzo, de Patentes, con el título Patrón Primario de Ruido Térmico de Banda Ancha (Referencia P-101061) con fecha 7 de febrero de 2011. ABSTRACT This Ph. D. work describes a number of investigations that were performed along the years 2008 to 2011, as a preparation for the study and design of a coaxial cryogenic reference noise standard. Reliable and traceable measurement underpins the welfare of a modern society and plays a critical role in supporting economic competitiveness, manufacturing and trade as well as quality of life. In our modern world, a well developed measurement infrastructure gives confidence in many aspects of our daily life, for example by enabling the development and manufacturing of reliable, high quality and innovative products; by supporting industry to be competitive and sustainable in its production; by removing technical barriers to trade and supporting fair trade; by ensuring safety and effectiveness of healthcare; by giving response to the major challenges in key sectors such energy and environment, etc. With all this in mind we have developed a primary standard thermal noise with the aim of providing the Spanish metrology system with a new primary standard for noise reference. This standard will allow development of reliable and traceable measurements in the field of calibration and measurement of electromagnetic noise RF and microwave devices. This standard has been designed to work in the frequency range from 10 MHz to 26.5 GHz, meeting the following specifications: 1. Noise temperature output is to be nominally ~ 83 K. 2. Noise temperature uncertainty less than ± 1 K in the frequency range from 0.01 to 26.5 GHz. 3. Broadband performance requires as low a reflection coefficient as possible from 0.01 to 26.5 GHz. The present Ph. D. work is divided into three clearly differentiated parts. The first one, which comprises Chapters 1 to 5, presents the whole process of simulation and adjustment of the main parameters of the device in order to define those of them which are critical for the manufacturing of the device. Next, the second part consists of Chapter 6 where the necessary computations to obtain the output noise temperature of the device are carried out. The third and last part, Chapter 7, is devoted to the estimation of the uncertainty related to the noise temperature of the noise primary standard as obtained in the preceding chapter. More specifically, Chapter 1 provides a thorough introduction to the scientific and technological environment where this research takes place. It also details the objectives to be achieved and presents the methodology used to achieve them. Chapter 2 describes the characterization and selection of the bead dielectric material inside the transmission line, intended to connect the two coaxial conductors equalizing the temperature between the two of them and thus keeping the characteristic impedance constant for the whole standard. In addition the dielectric properties of liquid nitrogen are analyzed in order to assess their influence on the impedance of the transmission line. Chapter 3 analyzes the behavior of two different loads and of a commercial airline when subjected to cryogenic working conditions. This study is intended to obtain the variation in the reflection coefficient when the temperature changes from room to cryogenic temperature, and to check whether these devices can be damaged as a result of working at cryogenic temperatures. Also we try to see whether the load changes its behavior after successive cycles of cooling / heating, in order to obtain a bound for the allowed variation of the reflection coefficient of the load. Chapter 4 analyzes the ring structure of the dielectric material used in the NBS technical note 1074 of NIST, in order to obtain its scattering parameters that will be used for computation of its effect upon the reflection coefficient of the whole coaxial structure. Subsequently, we perform a further investigation with the aim of improving the design of NBS technical note 1074 of NIST, and modifications are introduced in the geometry of the transition area in order to reduce the reflection it produces. We first analyze the ring, specifically the influence of the radius of inner conductor of the bead, and then make changes in its geometry so that it presents the same characteristic impedance as that of the line. Finally we analytically obtain the relationship between the inner conductor radius and the radius of the transition from ring, in order to ensure the heat flow through the transition thus keeping the same reflection coefficient, and at the same time meeting the robustness requirements and the feasibility of manufacturing. Chapter 5 analyzes the thermal behavior of the noise standard and its influence on the conductivity of metallic materials. Both possibilities are raised that the liquid nitrogen is kept outside the line or that it penetrates inside. In both cases, given the rotational symmetry of the structure, we have simulated a section of coaxial line, i.e. the equivalent two-dimensional problem has been resolved, although the results are applicable to the actual three-dimensional structure. For thermal simulation Matlab™ PDE Toolbox has been used. In Chapter 6 we compute the output noise temperature of the device. The starting point is the analysis of the contribution to the overall noise temperature of each section making up the standard. Moreover the influence of the variations in the parameters of all elements of the standard is analyzed, specifically the variation of the reflection coefficient along the entire device. Once the electromagnetic noise standard has been described and analyzed, in Chapter 7 we describe the steps followed to estimate the uncertainty of the output electromagnetic noise temperature. This is done using two methods, the classic analytical approach following the Guide to the Estimation of Uncertainty [GUM95] and numerical simulations made with the Monte Carlo method. Chapter 8 discusses the conclusions and achievements. During the development of this thesis, a novel device was obtained which was potentially patentable, and which was finally registered through the Spanish Patent and Trademark Office (SPTO) in Madrid, in accordance with the provisions of Article 20 of Law 11/1986 about Patents, dated March 20th, 1986. It was registered under the denomination Broadband Thermal Noise Primary Standard (Reference P-101061) dated February 7th, 2011.

Comparison of numerical models for vibro-acoustic analysis of structural panels in low modal density range engaging air layers

During launch, satellite and their equipment are subjected to loads of random nature and with a wide frequency range. Their vibro-acoustic response is an important issue to be analysed, for example for folded solar arrays and antennas. The main issue at low modal density is the modelling combinations engaging air layers, structures and external fluid. Depending on the modal density different methodologies, as FEM, BEM and SEA should be considered. This work focuses on the analysis of different combinations of the methodologies previously stated used in order to characterise the vibro-acoustic response of two rectangular sandwich structure panels isolated and engaging an air layer between them under a diffuse acoustic field. Focusing on the modelling of air layers, different models are proposed. To illustrate the phenomenology described and studied, experimental results from an acoustic test on an ARA-MKIII solar array in folded configuration are presented along with numerical results.

Broadband active differential array for the mid-frequency SKA band

This paper presents the design and characterization process of an active array demonstrator for the mid-frequency range (i.e., 300 MHz-1000 MHz) of the future Square Kilometre Array (SKA) radio telescope. This demonstrator, called FIDA3 (FG-IGN: Fundación General Instituto Geográfico Nacional - Differential Active Antenna Array), is part of the Spanish contribution for the SKA project. The main advantages provided by this design include the use of a dielectric-free structure, and the use of a fully-differential receiver in which differential low-noise amplifiers (LNAs) are directly connected to the balanced tapered-slot antennas (TSAs). First, the radiating structure and the differential low-noise amplifiers were separately designed and measured, obtaining good results (antenna elements with low voltage standing-wave ratios, array scanning capabilities up to 45°, and noise temperatures better than 52 K with low-noise amplifiers at room temperature). The potential problems due to the differential nature of the proposed solution are discussed, so some effective methods to overcome such limitations are proposed. Second, the complete active antenna array receiving system was assembled, and a 1 m2 active antenna array tile was characterized.

Simulating the effects of dominance and epistasis on selection response in the CIMMYT wheat breeding program using QuCim

Plant breeders use many different breeding methods to develop superior cultivars. However, it is difficult, cumbersome, and expensive to evaluate the performance of a breeding method or to compare the efficiencies of different breeding methods within an ongoing breeding program. To facilitate comparisons, we developed a QU-GENE module called QuCim that can simulate a large number of breeding strategies for self-pollinated species. The wheat breeding strategy Selected Bulk used by CIMMYT's wheat breeding program was defined in QuCim as an example of how this is done. This selection method was simulated in QuCim to investigate the effects of deviations from the additive genetic model, in the form of dominance and epistasis, on selection outcomes. The simulation results indicate that the partial dominance model does not greatly influence genetic advance compared with the pure additive model. Genetic advance in genetic systems with overdominance and epistasis are slower than when gene effects are purely additive or partially dominant. The additive gene effect is an appropriate indicator of the change in gene frequency following selection when epistasis is absent. In the absence of epistasis, the additive variance decreases rapidly with selection. However, after several cycles of selection it remains relatively fixed when epistasis is present. The variance from partial dominance is relatively small and therefore hard to detect by the covariance among half sibs and the covariance among full sibs. The dominance variance from the overdominance model can be identified successfully, but it does not change significantly, which confirms that overdominance cannot be utilized by an inbred breeding program. QuCim is an effective tool to compare selection strategies and to validate some theories in quantitative genetics.

Detection of fruit and the selection of primate visual pigments for color vision

Primates have X chromosome genes for cone photopigments with sensitivity maxima from 535 to 562 nm. Old World monkeys and apes (catarrhines) and the New World ( platyrrhine) genus Alouatta have separate genes for 535-nm ( medium wavelength; M) and 562-nm ( long wavelength; L) pigments. These pigments, together with a 425-nm ( short wavelength) pigment, permit trichromatic color vision. Other platyrrhines and prosimians have a single X chromosome gene but often with alleles for two or three M/L photopigments. Consequently, heterozygote females are trichromats, but males and homozygote females are dichromats. The criteria that affect the evolution of M/L alleles and maintain genetic polymorphism remain a puzzle, but selection for finding food may be important. We compare different types of color vision for detecting more than 100 plant species consumed by tamarins ( Saguinus spp.) in Peru. There is evidence that both frequency-dependent selection on homozygotes and heterozygote advantage favor M/L polymorphism and that trichromatic color vision is most advantageous in dim light. Also, whereas the 562-nm allele is present in all species, the occurrence of 535- to 556-nm alleles varies between species. This variation probably arises because trichromatic color vision favors widely separated pigments and equal frequencies of 535/543- and 562-nm alleles, whereas in dichromats, long-wavelength pigment alleles are fitter.

Suppression of spurious intermediate frequency modes in under-integrated elements by combined stiffness/viscous stabilization

Solutions employing perturbation stiffness or viscous hourglass control with one-point quadrature finite elements often exhibit spurious modes in the intermediate frequency range. These spurious frequencies are demonstrated in several examples and their origin is explained. Then it is shown that by critically damping the hourglass modes, these spurious mid-range frequency modes can be suppressed. Estimates of the hourglass frequency and damping coefficients are provided for the plane 4-node quadrilateral and a 4-node shell element. Results are presented that show almost complete annihilation of spurious intermediate frequency modes for both linear and non-linear problems. Copyright (c) 2005 John Wiley & Sons, Ltd.

Electrical impedance tomography in extremely prematurely born infants and during high frequency oscillatory ventilation analyzed in the frequency domain

Functional electrical impedance tomography (EIT) measures relative impedance change that occurs in the chest during a distinct observation period and an EIT image describing regional relative impedance change is generated. Analysis of such an EIT image may be erroneous because it is based on an impedance signal that has several components. Most of the change in relative impedance in the chest is caused by air movement but other physiological events such as cardiac activity change in end expiratory level or pressure swings originating from a ventilator circuit can influence the impedance signal. We obtained EIT images and signals in spontaneously breathing healthy adults, in extremely prematurely born infants on continuous positive airway pressure and in ventilated sheep on conventional mechanical or high frequency oscillatory ventilation (HFOV). Data were analyzed in the frequency domain and results presented after band pass filtering within the frequency range of the physiological event of interest. Band pass filtering of EIT data is necessary in premature infants and on HFOV to differentiate and eliminate relative impedance changes caused by physiological events other than the one of interest.

Functional connectivity of gamma EEG activity is modulated at low frequency during conscious recollection

We examined two subjectively distinct memory states that are elicited during recognition memory in humans and compared them in terms of the gamma oscillations (20–60 Hz) in the electroencepahalogram (EEG) that they induced. These subjective states, ‘recollection’ and ‘familiarity’ both entail correct recognition but one involves a clear and conscious recollection of the event including memory for contextual detail whilst the other involves a sense of familiarity without clear recollection. Here we show that during a verbal recognition memory test, the subjective experience of ‘recollection’ induced higher amplitude gamma oscillations than the subjective experience of ‘familiarity’ in the time period 300–500 ms after stimulus presentation. Recollection, but not familiarity, was also associated with greater functional connectivity in the gamma frequency range between frontal and parietal sites. Furthermore, the magnitude of the gamma functional connectivity varied over time and was modulated at 3 Hz. Previous studies in animals have shown local theta frequency modulation (3–7 Hz) of gamma-oscillations but this is the first time that a similar effect has been reported in the human EEG.

Low frequency dielectric spectroscopy of bitumen binders as an indicator of adhesion potential to quartz aggregates using Portland cement

The purpose of this investigation was to interpret the bitumen-aggregate adhesion based on the dielectric spectroscopic response of individual material components utilizing their dielectric constants, refractive indices and average tangent of the dielectric loss angle (average loss tangent). Dielectric spectroscopy of bitumen binders at room temperature was performed in the frequency range of 0.01–1000 Hz. Dielectric spectroscopy is an experimental method for characterizing the dielectric permittivity of a material as a function of frequency. Adhesion data has been determined using the Rolling bottle method. The results show that the magnitude of the average tangent of the dielectric loss angle (average loss tangent) depends on bitumen type. The average loss tangent in the frequency range 0.01–1 Hz is introduced as a potential indicator for predicting polarizability and, thereby, adhesion potential of bitumen binders to quartz aggregates when using Portland cement. In order to obtain acceptable adhesion of 70/100 penetration grade bitumen binders and quartz aggregates when using Portland cement, it is suggested that the binder have an average tan δ > 0.035 in the frequency range 0.01–1 Hz.

A LOFAR mini-survey for low-frequency radio emission from the nearest brown dwarfs

We have conducted a mini-survey for low-frequency radio emission from some of the closest brown dwarfs to the Sun with rapid rotation rates: SIMP J013656.5 +093347, WISEPC 150649.97+702736.0, and WISEPA J174124.26+255319.5.We have placed robust 3s upper limits on the flux density in the 111 – 169 MHz frequency range for these targets: WISE 1506: < 0:72 mJy; WISE 1741: < 0:87 mJy; SIMP 0136: < 0:66 mJy. At 8 hours of integration per target to achieve these limits, we find that systematic and detailed study of this class of object at LOFAR frequencies will require a substantial dedication of resources.

Components and circuits for tunneling diode based high frequency sources

Terahertz (THz) technology has been generating a lot of interest because of the potential applications for systems working in this frequency range. However, to fully achieve this potential, effective and efficient ways of generating controlled signals in the terahertz range are required. Devices that exhibit negative differential resistance (NDR) in a region of their current-voltage (I-V ) characteristics have been used in circuits for the generation of radio frequency signals. Of all of these NDR devices, resonant tunneling diode (RTD) oscillators, with their ability to oscillate in the THz range are considered as one of the most promising solid-state sources for terahertz signal generation at room temperature. There are however limitations and challenges with these devices, from inherent low output power usually in the range of micro-watts (uW) for RTD oscillators when milli-watts (mW) are desired. At device level, parasitic oscillations caused by the biasing line inductance when the device is biased in the NDR region prevent accurate device characterisation, which in turn prevents device modelling for computer simulations. This thesis describes work on I-V characterisation of tunnel diode (TD) and RTD (fabricated by Dr. Jue Wang) devices, and the radio frequency (RF) characterisation and small signal modelling of RTDs. The thesis also describes the design and measurement of hybrid TD oscillators for higher output power and the design and measurement of a planar Yagi antenna (fabricated by Khalid Alharbi) for THz applications. To enable oscillation free current-voltage characterisation of tunnel diodes, a commonly employed method is the use of a suitable resistor connected across the device to make the total differential resistance in the NDR region positive. However, this approach is not without problems as the value of the resistor has to satisfy certain conditions or else bias oscillations would still be present in the NDR region of the measured I-V characteristics. This method is difficult to use for RTDs which are fabricated on wafer due to the discrepancies in designed and actual resistance values of fabricated resistors using thin film technology. In this work, using pulsed DC rather than static DC measurements during device characterisation were shown to give accurate characteristics in the NDR region without the need for a stabilisation resistor. This approach allows for direct oscillation free characterisation for devices. Experimental results show that the I-V characterisation of tunnel diodes and RTD devices free of bias oscillations in the NDR region can be made. In this work, a new power-combining topology to address the limitations of low output power of TD and RTD oscillators is presented. The design employs the use of two oscillators biased separately, but with the combined output power from both collected at a single load. Compared to previous approaches, this method keeps the frequency of oscillation of the combined oscillators the same as for one of the oscillators. Experimental results with a hybrid circuit using two tunnel diode oscillators compared with a single oscillator design with similar values shows that the coupled oscillators produce double the output RF power of the single oscillator. This topology can be scaled for higher (up to terahertz) frequencies in the future by using RTD oscillators. Finally, a broadband Yagi antenna suitable for wireless communication at terahertz frequencies is presented in this thesis. The return loss of the antenna showed that the bandwidth is larger than the measured range (140-220 GHz). A new method was used to characterise the radiation pattern of the antenna in the E-plane. This was carried out on-wafer and the measured radiation pattern showed good agreement with the simulated pattern. In summary, this work makes important contributions to the accurate characterisation and modelling of TDs and RTDs, circuit-based techniques for power combining of high frequency TD or RTD oscillators, and to antennas suitable for on chip integration with high frequency oscillators.

Voice acoustic profi le of males exposed to occupational infrasound and low-frequency noise

Background: Vibroacoustic disease (VAD) is a systematic pathology characterized by the abnormal growth of extra-cellular matrices in the absence of infl ammatory processes, namely collagen and elastin, both of which are abundant in the basement membrane zone of the vocal folds. VAD can develop due to long-term exposure to infrasound and low-frequency noise (ILFN, <500 Hz). Mendes et al. (2006, 2008 and 2012) revealed that ILFN-exposed males and females presented an increased fundamental frequency (F0), decreased jitter %, and reduced maximum phonation frequency range, when compared with normative data. Temporal measures of maximum phonation time and S/Z ratio were generally reduced. Study Aims: Herein, the same voice acoustic parameters of 48 males, 36 airline pilots and 12 cabin crewmembers (age range 25-60 years) were studied, and the effects and interaction of age and years of ILFN exposure were investigated within those parameters. ILFN-exposure time (i.e. years of professional activity) ranged from 3.5 to 36 years. Materials and Methods: Spoken and sung phonatory tasks were recorded with a DA-P1 Tascam DAT and a C420III PP AKG head-worn microphone, positioned at 3 cm from the mouth. Acoustic analyses were performed using KayPENTAX Computer Speech Lab and Multi-Dimensional Voice Program. Results: Results revealed that even though pilots and cabin crewmembers were exposed to occupational environments with distinct (ILFN-rich) acoustical frequency distributions and sound pressure levels, differences in the vocal acoustic parameters were not evident. Analyzing data from both professional groups (N = 48) revealed that F0 increased signifi cantly with the number of years of professional activity. Conclusion: These results strongly suggest that the number of years of professional activity (i.e. total ILFN exposure time) had a signifi cant effect on F0. Furthermore, they may refl ect the histological changes specifi cally observed on the vocal folds of ILFN-exposed professionals.