回转窑热解处理废锌锰电池试验研究

我国电池生产量已经达到209亿节（2003年），多年来一直占据世界第一大电池生产国的地位，其中锌锰电池占大多数。废锌锰电池丢弃后，其中的重金属物质会逐渐渗透到地下，污染土壤和水体。重金属在生物体内富集，会使生物体致畸或致变。但同时，废锌锰电池中也含有大量有用的资源如锌、二氧化锰等。应对其进行回收利用，变废为宝。本文介绍了废锌锰电池回收处理的主要技术及研究进展，不同的处理技术回收废锌锰电池时的目标产物各不相同，但一般可分为以下几种：以单质形式回收锌、锰和汞；以合金的形式回收锌和锰；回收锌和二氧化锰；回收各金属元素制备复合微量元素肥料；回收锌、锰元素制备锰锌铁氧体；回收锌、锰元素制备硫酸锌和碳酸锰等。本文对一些废锌锰电池回收处理技术的优缺点从无害化程度、资源化程度、产品等级、工艺要求以及二次污染五个方面进行了分析和比较。在对国内外废锌锰电池回收处理技术进行分析比较的基础上提出了一种成本较低、可操作性较强的处理技术：先以干法除去废锌锰电池中的汞，然后以湿法除去其它的有害重金属并进一步加工制备有机螯合微量元素肥料。 本文以回转窑中物料停留时间的经验公式和传热学的知识设计和计算了回转窑的长度和内径尺寸、电热丝的功率以及外围的保温材料厚度等参数。用保温材料和润滑油相结合的方式对回转窑的连接部分实行密封。通过调整回转窑的转速和回转窑支架两端高度差的方式控制物料在回转窑中的停留时间，从而调节热解时间的长短。利用自动控制设备调节电热丝的功率从而调节试验中的热解温度。利用该回转窑在不同条件下对热解处理废锌锰电池进行了试验研究，热解过程中产生的尾气和颗粒物用一系列吸收液进行吸收和固定。 在热解试验中改变影响热解过程的三种因素：热解温度、热解时间和载气流速并按三因素四水平的正交方法安排试验。改变废锌锰电池热解过程中的热解温度、热解时间和载气流速三种因素进行正交试验并利用正交统计学的方法分析了这三种因素对热解除汞率的影响。利用ICP检测仪测定了各吸收液中汞的含量，并分析热解气体产物经过系列吸收液时汞被吸收的情况以及汞的形态分布。利用气相色谱仪对尾气成分进行了测定，并对热解过程中产气的过程和规律进行了分析。用X射线衍射测试的方法研究了热解前后锌锰电池的物质形态变化情况。对除汞率的正交统计分析表明，合适的热解条件为：热解温度690℃，热解时间100min，载气流速0.06m3/h，在这种试验条件下热解处理废锌锰电池的除汞率达到100%。同时还得到：热解时间对除汞效果影响最大，热解温度次之，载气流速的影响较小。ICP测试的结果表明：热解尾气在经过试验中设置的吸收瓶后，其中的汞被完全吸收，尾气中95%以上的汞以单质的形式存在。气相色谱分析的结果表明，热解开始后，废锌锰电池中的有机质迅速分解，其产物为C2H4、CH4和H2等。一段时间后，有机质的分解量大幅度减少，同时废电池中的石墨碳和高价金属氧化物发生氧化还原反应，生成CO气体。对废锌锰电池原料以及热解残渣的X射线衍射分析表明，当热解温度为350℃时，X射线衍射图谱上2θ值为35°附近的区域有新峰出现，但不明显，说明有结晶体形成但量不大。500℃时上述峰明显增强，这是由于ZnO和FeO形成了结晶体，同时在2θ值为41°附近有新峰出现，这是高价锰氧化物与石墨碳发生氧化还原反应生成了MnO并形成了结晶体。650℃时，2θ值在41°附近的峰显著增强，且热解过程中形成的峰稳定下来，基本上不再有新的结晶体生成。热解后，高价锰氧化物的相对含量从32.2%下降到4.6%，而MnO的相对含量则从6.4%上升到38.6%。热解后的残渣中晶体物质含量大，金属元素大多以低价态存在，适合于制备有机螯合微量元素肥料。

SYNTHESIS OF THE CLINOPYROXENES JOIN CAMGSI2O6-NAALSI2O6 FOR JEWELRY

Clinopyroxenes of the join CaMgSi2O6(diopside)-NaAlSi2O6 (jadeite) were synthesized in the temperature range 800-1900 degrees C and under varying pressure, 10-55 kbar. The stability regions of various compositions of diopside-jadeite have been established experimentally using different compositions of glass materials: stoichiometric composition NaAlSi2O6, 0.1CaMgSi(2)O(6)-0.9NaAlSi(2)O(6), 0.2CaMgSi(2)O(6)0.8NaAlSi(2)O(6), 0.3CaMgSi(2)O(6)-0.7NaAlSi(2)O(6), and 0.4CaMgSi(2)O(6)-0.6NaAlSi(2)O(6). Unit cell parameters of synthetic clinopyroxenes with the above compositions were determined. The physical properties, such as hardness, toughness, density, and refractive index, etc., were also measured. The results show that synthetic clinopyroxenes have the same properties as the natural one. The gem quality of diopside-jadeite clinopyroxenes was achieved by synthesised on the basis of the above experiments. Various colouring agents, such as Cr2O3, Co2O3, NiO2, Fe2O3, TiO2, MnO, CuO, and their combinations, FeO-Cr2O3, etc., were added to obtain the different colours of gem. In addition, small amounts of the rare-earth oxides, such as CeO2, Nd2O3, Sm2O3, Dy2O3, Eu2O3, Er2O3, Pr6O11, Lu2O3 and CuO-Eu2O3, Co2O3Nd2O3, etc., were also added to produce fluorescent clinopyroxenes for jewellery.

钙钛石型复合氧化物La_(1-x)Sr_xFeO_(3-λ)催化性能的研究——Ⅲ.Fe离子的状态及其对催化活性的影响

用Mossbauer,IR等技术及对样品磁化率与电导率的测量,研究了钙钛石型复合氧化物La_(1-x)Sr_xFeO_(3-λ)体系中,活性金属铁离子在改变x时的价态和配位环境的变化及其对催化活性的影响。发现催化剂在0≤x<0.5～0.7范围内,其Fe—O键的相互作用较强,催化活性主要由催化剂的表面化学所控制;在0.7≤x≤1.0范围内,催化剂中Fe-O键相互作用减弱,氧空位出现有序化,在这一范围内,催化活性主要由催化剂的体相化学控制。

A preliminary study on thermoluminescence characteristics of sediments from the North Pacific

Thirty-eight surficial deposit samples were collected from the equatorial North Pacific, and the natural thermoluminescence (TL) characteristics of both bulk and clay fraction samples ( < 2 mu m fractions) were studied by the FJ427 - Al automatic TL Dosimeter for the first time. With the measurements of clay mineral composition, element composition by XRD and ICP, the correlations between TL intensity and sedimentary environment proxies were analyzed, such as water depth, ratio of FeO to Fe2O3 contents, LOI, and major clay mineral concentration, and it was found the bulk sample's TL signal was stronger than the clay ones. Usually, increase in the clay components may result in the decrease of TL intensity. From the shape of TL curves, the pelagic sediments can be divided into two groups: the majority group has two glow peaks, in general, the first peak is broad and flat, but the second narrow and sharp; the minority group only has a single peak because the first is absent. The peak centers of TL curves are almost fixed, falling in the temperature sections 230 similar to 260 and 390 similar to 405 degrees C respectively. Lorentz model packed in the Origin 7.5 was chosen to deal with the TL curves. From the processing results, three parameters ( H, C and A), corresponding to the height, center, and kurtosis of TL curve, were obtained to describe the curve characteristics. The correlations between TL curve parameters and sedimentary environment proxies were also calculated. On the basis of the above work, the relationship between TL characteristics and sediment type, mineral composition, sedimentary environment of surface sediments was discussed in the study area, and a conclusion is: sediments from the environment of shallower water, higher organic contents and weaker reductivity have stronger TL signals.

Genesis of Th-230 excess in basalts from mid-ocean ridges and ocean islands: Constraints from the global U-series isotope database and major and rare earth element geochemistry

Based on Th-230-U-238 disequilibrium and major element data from mid-ocean ridge basalts (MORBs) and ocean island basalts (OIBs), this study calculates mantle melting parameters, and thereby investigates the origin of Th-230 excess. (Th-230/U-238) in global MORBs shows a positive correlation with Fe-8, P (o), Na-8, and F-melt (Fe-8 and Na-8 are FeO and Na2O contents respectively after correction for crustal fractionation relative to MgO = 8 wt%, P (o)=pressure of initial melting and F (melt)=degree of melt), while Th-230 excess in OIBs has no obvious correlation with either initial mantle melting depth or the average degree of mantle melting. Furthermore, compared with the MORBs, higher (Th-230/U-238) in OIBs actually corresponds to a lower melting degree. This suggests that the Th-230 excess in MORBs is controlled by mantle melting conditions, while the Th-230 excess in OIBs is more likely related to the deep garnet control. The vast majority of calculated initial melting pressures of MORBs with excess Th-230 are between 1.0 and 2.5 GPa, which is consistent with the conclusion from experiments in recent years that D (U)> D (Th) for Al-clinopyroxene at pressures of > 1.0 GPa. The initial melting pressure of OIBs is 2.2-3.5 GPa (around the spinel-garnet transition zone), with their low excess Ra-226 compared to MORBs also suggesting a deeper mantle source. Accordingly, excess Th-230 in MORBs and OIBs may be formed respectively in the spinel and garnet stability field. In addition, there is no obvious correlation of K2O/TiO2 with (Th-230/U-238) and initial melting pressure (P (o)) of MORBs, so it is proposed that the melting depth producing excess Th-230 does not tap the spinel-garnet transition zone. OIBs and MORBs in both (Th-230/U-238) vs. K2O/TiO2 and (Th-230/U-238) vs. P (o) plots fall in two distinct areas, indicating that the mineral phases which dominate their excess Th-230 are different. Ce/Yb-Ce curves of fast and slow ridge MORBs are similar, while, in comparison, the Ce/Yb-Ce curve for OIBs shows more influence from garnet. The mechanisms generating excess Th-230 in MORBs and OIBs are significantly different, with formation of excess Th-230 in the garnet zone only being suitable for OIBs.

Generation and evolution of magma beneath the East Pacific Rise: Constraints from U-series disequilibrium and plagioclase-hosted melt inclusions

Mid-ocean ridge basalt (MORB) samples from the East Pacific Rise (EPR 12 degrees 50'N) were analyzed for U-series isotopes and compositions of plagioclase-hosted melt inclusions. The Ra-226 and Th-230 excesses are negatively correlated; the Ra-226 excess is positively correlated with Mg# and Sm/Nd, and is negatively correlated with La/Sm and Fe-8; the Th-230 excess is positively correlated with Fe-8 and La/Sm and is negatively correlated with Mg# and Sm/Nd. Interpretation of these correlations is critical for understanding the magmatic process. There are two models (the dynamic model and the "two-porosity" model) for interpreting these correlations, however, some crucial parameters used in these models are not ascertained. We propose instead a model to explain the U-series isotopic compositions based on the control of melt density variation. For melting either peridotite or the "marble-cake" mantle, the FeOt content, Th-230 excess and La/Sm ratio increases and Sm/Nd decreases with increasing pressure. A deep melt will evolve to a higher density and lower Mg# than a shallow melt, the former corresponds to a long residence time, which lowers the Ra-226 excess significantly. This model is supported by the existence of low Ra-226 excesses and high Th-230 excesses in MORBs having a high Fe-8 content and high density. The positive correlation of Ra-226 excess and magma liquidus temperature implies that the shallow melt is cooled less than the deep melt due to its low density and short residence time. The correlations among Fe-8, Ti-8 and Ca-8/Al-8 in plagioclase-hosted melt inclusions further prove that MORBs are formed from melts having a negative correlation in melting depths and degrees. The negative correlation of Ra-226 excess vs. chemical diversity index (standard deviation of Fe-8, Ti-8 and Ca-8/Al-8) of the melt inclusions is in accordance with the influence of a density-controlled magma residence time. We conclude that the magma density variation exerts significant control on residence time and U-series isotopic compositions. (c) 2010 Elsevier B.V. All rights reserved.

华北克拉通孔玆岩系中石榴子石花岗岩的成因：熔体与残留相混合机制的研究

The most widespread rock associations in the Western Block of North China Craton are khondalites distributed mainly in Jining, Liangcheng and Datong. A large quantitiy of garnet-bearing granites are contained in the khondalites. A great deal of research has been carried out on them by previous researchers. Studies of these garnet-bearing granites consist essentially of structural characteristics, petrography and geochemistry, and finally geochronological determinations. Summing up these researches, it will not be difficult to see that all of these authors have regarded these large numbers of garnets (up to 20%) contained in granites as crystallized products from magmas, but they have not proved this from petrological perspective. Theoretically, there are possibly three kinds of petrogenesis as to these garnets. The first one is that they have been transferred to the granites from khondalites by melt when anatexis happened to khondalites, and they, in essence, are residual metamorphic garnets; The second one is that when the khondalites were being melted, these garnets were produced from biotite dehydration melting, and the newly formed garnets intruded together with the melt and eventually molded the garnet-bearing granites. Garnets of this possible kind either showed independent crystals, or garnets from khondalites took place secondary growth under favorable temperature and pressure conditions for their crystallization; The last possibility is that these garnets were crystallized from magmas in which suitable pressure, temperature and composition were available. These garnets, generally, should be fine-grained. The aim of this study is, through examining the mineral chemistry of the garnets and the whole rock chemistry, to ascertain under which kind of mechanism, in the world, did these garnets form? Besides, we try to calculate the temperatures under which khondalites began melting and reactions of the garnets and the cooled melts happened by garnet-biotite thermometry. The whole rock chemistry analyses of the garnet-bearing granites tell us that all the samples are strongly peraluminous (A/CNK greater than 1.1) on the A/NK vs. A/CNK plot. On the SiO2-K2O plot, the granites are mainly constrained to be high-K calc-alkaline and calc-alkaline series, consistent with previous researches. On the ACF（（Al2O3-Na2O-K2O）-FeO(T)-CaO） discrimination plot, all the six garnet-bearing granite samples drop into the area of S-type granites. The relationship between CaO/Na2O and SiO2 shows that the overwhelming majority of garnet-bearing granites have a CaO/Na2O value over 0.3, revealing that they probably come from metagreywacke precursors or mediate-felsic orthogeneisses compositionally similar to them. Detailed EPMA analyses conducted on the garnets contained in the garnet-bearing granites show that all the garnets are dominated by almandine and pyrope, which occupy 92-96% (Weight Percentage) of each garnet analyzed, typical of granulite facies. Their chemical composition is entirely different from those crystallized in magmas, but extremely similar to those of typical granulite facies metapelites in khondalites and typical granulites, indicating all the garnets to be metamorphogenic. In addition, REEs distribution patterns of the garnets are totally different from typical biotite granites and peraluminous granites. In other words, both LREE and HREE of our garnets are evidently lower than those from these two kinds of rocks. Moreover, compared to the REE pattern of the garnets from typical amphibolites, LREE content of our garnets is obviously higher and HREE content is a little lower. However, REE patterns of our garnets are completely in harmony with those of garnets from typical granulites. So, the REE patterns of garnets, again, prove that all the garnets we studied are metamorphogenic. Biotites appear in two forms, being as inclusions in the garnet and as selvages immediately adjacent to the garnet, respectively. Two reactions and their corresponding temperatures, with the help of petrography and Garnet-Biotite geothermometers, could be obtained, which are Bt+ Pl+ Qtz→Kfs+ Opx+ Grt+ melt as positive reaction and Kfs+ Grt+ melt→Bt+ Pl+ Qtz as reverse reaction, respectively. Summing up the discussion above, we declare that the garnet-bearing granites distributed in the Western Block of North China Craton are the mixture of melts and restites resulted from biotite dehydration melting. The garnets contained in the restites are the products from biotite dehydration melting and restites from the khondalites, respectively.

北大别黄土岭麻粒岩变质演化：对大别造山带演化进程的指示意义

Granulites from Huangtuling in the North Dabie metamorphic core complex in eastern China preserve rare mineralogical and mineral chemical evidence for multistage metamorphism related to Paleoproterozoic metamorphic processes, Triassic continental subduction-collision and Cretaceous collapse of the Dabieshan Orogen. Six stages of metamorphism are established, based on detailed mineralogical and petrological studies: (I) amphibolite facies (6.3–7.0 kbar, 520–550 °C); (II) high-pressure/high-temperature granulite facies (12–15.5 kbar, 920–980 °C); (III) cooling and decompression (4.8–6.0 kbar, 630-700 °C); (IV) medium-pressure granulite facies (7.7–9.0 kbar, 690–790 °C); (V) low-pressure/high-temperature granulite facies (4.0–4.7 kbar, 860–920 °C); (VI) retrograde greenschist facies overprint (1–2 kbar, 340–370 °C). The P–T history derived in this study and existing geochronological data indicate that the Huangtuling granulite records two cycles of orogenic crustal thickening events. The earlier three stages of metamorphism define a clockwise P–T path, implying crustal thickening and thinning events, possibly related to the assembly and breakup of the Columbia Supercontinent ca. 2000 Ma. Stage IV metamorphism indicates another crustal thickening event, which is attributed to the Triassic subduction/collision between the Yangtze and Sino–Korean Cratons. The dry lower crustal granulite persisted metastable during the Triassic subduction/collision due to lack of hydrous fluid and deformation. Stage V metamorphism records the Cretaceous collapse of the Dabieshan Orogen，possibly due to asthenosphere upwelling or removal of the lithospheric mantle resulting in heating of the granulite and partial melting of the North Dabie metamorphic core complex. Comparison of the Huangtuling granulite in North Dabie and the high-pressure (HP)–ultrahigh-pressure (UHP) metamorphic rocks in South Dabie indicates that the subducted upper (South Dabie) and lower (North Dabie) continental crusts underwent contrasting tectonometamorphic evolution during continental subduction–collision and orogenic collapse. High-pressure granulites are generally characterized by the absence of orthopyroxene. However, the Huangtuling felsic granulite rarely preserves the high-pressure granulite facies assemblage of garnet + orthopyroxene + biotite + plagioclase + K-feldspar + quartz. To investigate the effects of bulk rock composition on the stability of orthopyroxene-bearing, high-pressure granulite facies assemblages in the NCKFMASHTO (Na2O–CaO–K2O–FeO–MgO–Al2O3–SiO2–H2O–TiO2–Fe2O3) system, we constructed a series of P–T–X pseudosections based on the melt-reintegrated composition of the Huangtuling felsic high-pressure granulite. Our calculations demonstrate that the orthopyroxene-bearing, high-pressure granulite facies assemblages are restricted to low XAl [Al2O3/(Na2O + CaO + K2O + FeO + MgO + Al2O3) < 0.35, mole proportion] or high XMg [MgO/(MgO + FeO) > 0.85] felsic–metapelitic rock types. Our study also reveals that the XAl values in the residual felsic–metapelitic, high-pressure granulites could be significantly reduced by a high proportion of melt loss. We suggest that orthopyroxene-bearing high-pressure granulites occur in residual overthickened crustal basement under continental subduction–collision zones and arc–continent collision belts.

班公湖带多不杂超大型富金斑岩铜矿床的成岩成矿年代学、岩石学及高氧化岩浆¬流体-成矿作用

Duobuza copper deposit, newly discovered typical gold-rich porphyry copper deposit with superlarge potential, is located in the Tiegelong Mesozoic tectonic -magmatic arc of the southern edge of Qiangtang block and the northern margin of Bangonghu-Nujiang suture. Quartz diorite porphyrite and grandiorite porphyry, occurred in stock, are the main ore-bearing porphyries. As the emplacement of porphyry stock, a wide range of hydrothermal alteration has developed. Within the framework of the ore district, abundant hydrothermal magnetite developed, and the relationship between precipitation of copper and gold and hydrothermal magnetite seems much close. Correspondingly, a series of veinlets and network veinlets occurred in all alteration zones. Therefore, systematic research on such a superlarge high-grade Duobuza gold-rich porphyry copper deposit can fully revealed the metallogenic characteristics of gold-rich porphyry copper deposits in this region, establish metallogenetic model and prospecting criteria, and has important practical significance on the promotion of regional exploration. In addition, this research on it can enrich metallogenic theory of strong oxidation magma-fluid to gold-rich porphyry copper deposit, and will be helpful to understand the metallogenic characteristics in early of subduction of Gangdese arc stages and its entire evolution history of the Qinghai-Tibet Plateau, the temporal and spatial distribution of ore deposits and their geodynamics settings. Northern ore body of Duobuza copper deposit have been controlled with width (north-south) about 100 ~ 400 m, length (east-west) about 1400 m, dip of 200 °, angle of dip 65 °~ 80 °. And controlled resource amount is of 2.7 million tons Cu with grade 0.94% and 13 tons Au with 0.21g/tAu. Overall features of ore body are large scale, higher grade copper, gold-rich. Ore occurred in the body of granodiotite porphyry and quartz diorite porphyrite and its contact zone with wall rock. Through the detailed mapping and field work studies, some typies of alteration are identificated as follows: albitization, biotititation, sericitization, silication, epidotization, chloritization, carbonatization, illitization, kaolinization and so on. The range of alteration is more than 10km2. Wall alteration zone can be divided into potassic alteration, moderate argillization alteration, argillization, illite-hydromuscovite or propylitization from ore-bearing porphyry center outwards, but phyllic alteration has not well developed and only sericite-quartz veins occurred in local area. Moreover, micro-fracture is development in ore district , and correspondingly a series of veinlets are development as follows: biotite vein (EB type), K-feldspar-biotite-chalcopyrite-quartz vein, magnetite-antinolite-K-feldspar vein, quartz-chalcopyrite-magnetite veins (A-type), quartz-magnetite-biotite-K-feldspar vein, chalcopyrite veinlets in potassic alteration zone; (2) chalcopyrite occurring in the center vein–quartz vein (B type), chalcopyrite veinlets, chalcopyrite-gypsum vein in intermediate argillization alteration; (3) chalcopyrite- pyrite-quartz vein, pyrite-quartz vein, chalcopyrite-gypsum veins, quartz-gypsum- molybdenite-chalcopyrite vein in argillization alteration; (4) gypsum veins, quartz-(molybdenite)-chalcopyrite vein, quartz-pyrite vein, gypsum- chalcopyrite vein, potassium feldspar veinlets, Carbonate veins, quartz-magnetite veins in the wall rock. In short, various veins are very abundant within the framework of the ore district. The results of electronic probe microscopy analysis (EMPA) indicate that Albite (Ab 91.5~99.7%) occurred along the rim of plagioclase phenocryst and fracture, and respresents the earliest stages of alteration. K-feldspar (Or 75.1~96.9%) altered plagioclase phenocryst and matrix or formed secondary potassium feldspar veinlets. Secondary biotite occurred mainly in phenocryst, matrix and veinlets, belong to magnesium-rich biotite formed under the conditions of high-oxidation magma- hydrothermal. Chloritization developed in all alteration zones and alterd iron- magnesium minerals such as biotite and hornblende and then formed chlorite veinlets. As the temperature rises, Si in the tetrahedral site of chlorite decreased, and chlorite component evolved from diabantite to ripiolite. The consistent 280℃~360℃ of formation temperature hinted that chlorite formed on the same temperature range in all alteration zones. However, formation temperature range of chlorite from the gypsum-carbonate-chlorite vein was 190℃~220℃, and it may be the product of the latest stage of hydrothermal activity. The closely relationship between biotite and rutile indicate that most of rutiles are precipitated in the process of biotite alteration and recrystallization. In addition, the V2O3 concentration of rutile from ore body in Duobuza gold-rich porphyry copper deposit is >0.4％, indicate that V concentration in rutile has important significance on marking main ore body of porphyry copper deposit. Apatites from Duobuza deposit all are F-rich. And apatite in the wall rock contained low MnO content and relatively high FeO content, which may due to the basaltic composition of the wall rocks. The MnO in apatite from altered porphyry show a strong positive correlation with FeO. In addition, Cl/F ratio of apatite from wall rock was highest, followed by the potassic alteration zone and potassic alteration zone overprinted by moderate argillization alteration was the lowest. SO2 in Apatite are in the scope of 0 to 0.66%, biotite in the apatite has the highest SO2, followed by the potassic alteration zone, potassic alteration zone overprinted by moderate argillization alteration, and the lowest in the surrounding rocks, which may be caused by the decrease of oxygen fugacity of hydrothermal fluid and S exhaust by sulfide precipitation in potassic alteration. Magnetite in the wall rock have higher Cr2O3 and lower Al2O3 features compared with altered porphyry, this may be due to basalt wall rock generally has high Cr content. And magnetites have higher TiO2 content in potassic alteration than moderate argillization alteration overprinted by potassic alteration, argillization and wall rock, suggested that its formation temperature in potassic alteration was the highest among them. The ore minerals mainly are chalcopyrite and bornite, and Au contents of chalcopyrite, bornite, and pyrite are similar with chalcopyrite slightly higher. The Eu* negative anomaly of disseminated chalcopyrite was relatively lower than chalcopyrite in veinlets. Within a drill hole, the Eu* negative anomaly of disseminated chalcopyrite was gradually larger from bottom to top. Magnetite has the same distribution model, with obvious negative Eu* abnormal, and ΣREE in great changes. The gypsum has the highest ΣREE content and the obvious negative anomaly, and biotite obviously has the Eu* abnormal. Based on the petrographic and geochemical characteristics, five series of magmatic rocks can be broadly classified; they are volcanic rocks of the normal island arc, high-Nb basaltic rocks, adakites, altered porphyry and diorite. The Sr, Nd, Hf isotopes and geochemistry of various series of magmatic rock show that they may be the result of mixing between basic magma and various degrees of acid magma coming from lower crust melted by high temperature basic underplating from partial melting of the subduction sediment melt metasomatic mantle wedge. Furthermore S isotope and Pb isotope of the sulfide, ore-bearing porphyries and volcanic rocks indicated ore-forming source is the mantle wedge metasomatied by subduction sediment melt. Oxygen fugacity of magma estimated by Fe2O3/FeO of whole rock and zircon Ce4+/Ce3+ indicated that the oxidation of basalt-andesitic rocks is higher than ore-forming porphyry, and might imply high-oxidation characteristics of underplated basic magma. Its high oxidative mechanism is likely mantle sources metasomatied by subduction sediment magma, including water and Fe3+. And such high oxidation of basaltic magma is conducive to the mantle of sulfides in the effective access to melt. And the An component of dark part within plagioclase phenocryst zoning belong to bytownite (An 74%), and its may be a result of magma composition changes refreshment by basaltic magma injection. SHRIMP zircon U-Pb and LA-ICP-MS zircon U-Pb geochronology study showed that the intrusions and volcanic rocks from Duobuza porphyry copper deposit belong to early Cretaceous magma series (126~105Ma). The magma evolution series are as follows: the earliest diorite and diorite porphyrite → ore-bearing porphyry and barren grandiorite porphyry →basaltic andesite → diorite porphyrite → andesite → basaltic andesite, and magma component shows a evolution trend from intermediate to intermediate-acid to basic. Based on the field evidences, the formation age of high-Nb basalt may be the latest. The Ar-Ar geochronology of altered secondary biotite, K-feldspar and sericite shows that the main mineralization lasting a interval of about 4 Ma, the duration limit of whole magma-hydrothermal evolution of about 6 Ma, and possibly such a long duration limit may result in the formation of Duobuza super-large copper deposit. Moreover, tectonic diagram and trace element geochemistry of volcanic rocks and diorite from Duobuza porphyry copper deposit confirm that it formed in a continental margin arc environment. Zircon U-Pb age of volcanic rocks and porphyry fall in the range of 105~121Ma, and Duobuza porphyry copper deposit locating in the north of the Bangonghu- Nujiang suture zone, suggested that Neo-Tethys ocean still subducted northward at least early Cretaceous, and its closure time should be later than 105 Ma. Three major inclusion types and ten subtypes are distinguished from quartz phenocrysts and various quartz veins. Vapor generally coexisting with brine inclusions, suggest that fluid boiling may be the main ore-forming mechanism. Raman spectrums of fluid inclusions display that the content of vapor and liquid inclusion mainly contain water, and vapor occasionally contain a little CO2. In addition, the component of liquid inclusions mainly include Cl-, SO42-, Na+, K+, a small amount of Ca2+, F-; and Cl- and Na+ show good correlation. Vapor mainly contains water, a small amount of CO2, CH4 and C2H6 and so on. The daughter minerals identified by Laman spectroscopy and SEM include gypsum, chalcopyrite, halite, sylvite, rutile, potassium feldspar, Fe-Mn-chloride and other minerals, and ore-forming fluid belong to a complex hydrothermal system containing H2O-NaCl-KClFeCl2CaCl2. H and O isotopic analysis of quartz phenocryst, vein quartz, magnetite, chlorite and gypsum from all alteration zones show that the ore-forming fluid of Duobuza gold-rich porphyry copper deposit consisted mainly of magmatic water, without addition of meteric water. Duobuza gold-rich porphyry copper deposit formed by the primary magmatic fluid (600-950C), which has high oxidation, ultra-high salinity and metallogenic element-rich, exsolution direct from the magma, and it is representative of the typical orthomagmatic end member of the porphyry continuum. Moreover, the fluid evolution model of Duobuza gold-rich porphyry copper deposit has been established. Furthermore, two key factors for formation of large Au-rich porphyry copper deposit have been summed up, which are ore-forming fluids earlier separated from magma and high oxidation magma-mineralization fluid system.

东天山镁铁-超镁铁岩铜镍硫化物矿床通道式成矿机制与岩体含矿性评价研究

A mafic-ultramafic complex belt well developed in Eastern Tianshan, Xinjiang, NW China, which contains a series of Cu-Ni sulfide deposits. This area is the important production basis for Cu-Ni deposits, including Tulargen deposit, Hulu deposit, Huangshan-Huangshandong deposit, Hulu deposit, Xiangshan deposit, Tianyu deposit, Chuanzhu deposit. In China, especially Eastern Tianshan, it is prevalent that large Cu-Ni deposits occurred in small intrusions, typically including Jinchuan, Kalatongke, et al., so the ore-forming mechanism and evaluation rule for those small intrusions are very meaningful and of universal significance. On the basis of the research to typical Cu-Ni deposits, ore-forming conditions and processes are summarized through which to evaluate the ore-bearing potential for barren intrusions and unexplored mafic-ultramafic intrusions. By the contrast, metallogenic rule and mechanism of ore genesis are concluded, and evaluation system is preliminarily set up on the basis of these conclusions. Quantitatively simulation for the composition of olivine is introduced for the first time in China to discuss the interaction between magma and sulfide, and a new method to calculate the Mg-Fe composition of primitive magma is developed. Interaction between magma and sulfide liquid is used to get the Ni content in sulfide liquid. Sulfur isotopic characteristics in sulfide minerals in country rocks and ores are used to judge crustal sulfur introduction, which is applied for the first time in China. Re-Os isotopic characteristics are related to the ore-forming process, to interpret the process of enrichment of chalcophile elements. On the basis of the evaluation system, Mati, Chuanzhu, Luodong, Xiadong, those intrusions are evaluated to their ore-bearing potential. According to the studies to typical Cu-Ni deposits, conduit-type ore-forming model is set up, and the characteristics of the model are concluded systematically. The evaluation system and conduit-type ore-forming model can be helpful to the evaluation of mafic-ultramafic intrusions in this and similar mafic-ultramafic intrusion belts. The studied typical deposits and mafic-ultramafic intrusion include Tulargen deposit, Hulu deposit, Huangshandong deposit, Chuanzhu deposit, Mati intrusion，Luodong intrusion, Xiadong intrusion, and others. Through studies, there are similar characteristics for Tulargen and Hulu deposits in magma origin, composition of primitive magma（MgO=12.5%, FeO=12% and MgO=11%, FeO=10.5% respectively）, magma evolution, mechanism of sulfide segregation and conduit-type ore-forming process. By Re-Os isotopic system, the ore forming date of Tulargen deposit is 265.6±9.2Ma, which is consistent to regional metallogenic event, but little younger. The Mg-Fe composition of primitive magma of Baishiquan, Huangshandong area, Kalatongke is lower than that of Tulargen and Hulu deposit, showing common basalt composition. The Mg# value（Mg#=(Mg/Mg+Fe）increases gradually from Kalatongke to Baishiquan to Huangshan-Huangshandong East. Baishiquan intrusions show relatively higher crustal contamination by evidence of trace element, which indicates the lower magma original source, from depleted mantle to crust. One break is the discovery of komatiitic intrusion, Xiadong intrusion, which shows characteristics of highly magnesium (Max Fo=96). The primitive magma is calculated of MgO=28%，FeO=9%, belonging to komatiitic magma. Tectonic evolution of Eastern Tianshan is discussed. By the statistics of ore-forming data of porphyry copper deposits, magmatic sulfide Cu-Ni deposits, orogenic hydrothermal gold deposits, we believe that those deposits are the successive products of oceanic subduction, are and back-arc basin collision and post-orogenic extention. And Cu-Ni sulfide deposits and orogenic gold deposits occurred in the stage of post-orogenic extention. According to the conclusions, the conduit-type ore-forming mechanism of magmatic sulfide deposit is set up, and its characteristics and conditions are concluded as well. The conduit-type ore-forming system includes magma generation, sulfide segregation, enrichment of chalcophile elements, interaction of sulfide and magma, sulfide collection in limited space in magma conduit and bottom of the chamber, which make a whole ore-forming system.The ore-forming process of Cu-Ni sulfide deposits is concluded as three steps: 1. mantle derived magma rises upward to the middle-upper crust; 2. magma suffers crustal contamination of different degrees and assimilates crustal sulfur, which leads to sulfur saturation and sulfide segregation. Sulfide liquid interacts with magma and concentrates chalcophile elements; 3. enriched sulfide located in the conduit(Tulargen) or bottom of the chamber (Hulu). Depleted magma rises upward continuously to form barren complexes. For the practical cases, Tulargen deposit represents the feeding conduit, and Hulu deposit represents the bottom of the staging magma chamber. So the deeper of west of Tulargen and southwest of Hulu are the favorite locate for ore location. The evaluation for ore potential can be summarized as follows: (1) Olivine can be served as indicator for magma evolution and events of sulfide segregation; (2) Sulfur isotopic characteristics is an efficient method to judge sulfur origin for magmatic sulfide deposit; (3) Re-Os content of the ores can indicate interaction between sulfide and silicate magma and crustal contamination; (4) PGE mineralization is effected by degree of partial melting of mantle; (5) Cu/Zr is efficient parameter to judge sulfide segregation; (6) The effects of multiple magma fractionation and emplacement are important, for inverse order shows the destruction to previous solid lithofacies and orebodies. Mati, Chuanzhu, Xiadong, Luodong, mafic-ultramafic intrusions are evaluated using evaluation system above. Remarkable Ni depletion is found in olivine of Mati, and southwest of the intrusion can be hopeful location for ore location. Chuanzhu intrusion has remarkable evidence of sulfide segregation, but the intrusion represents the narrow feeder conduit, so the wide part of the conduit maybe the favorite location for sulfide to deposit. The ore potential of Luodong and Xiadong is not good. Both the intrusions show no Ni depletion in olivine, and there is no sulfide in country rocks, so no crustal sulfur is added into the magmatic system. For Sidingheishan, a very large intrusion, the phenomenon of sulfide segregation is found, but there are no favorite places for sulfide to deposit. So the Cu-Ni ore potential maybe not good, but PGE mineralization should be evaluated further.

大别山硬玉石英岩带中的水

The Dabie Mountains is a collisional orogenic belt between the North China and Yantze Continental plates. It is the eastern elongation of the Tongbai and Qingling orogen, and is truncated at its east end by the Tan-Lu fault. Jadeite-quartzite belt occurs in the eastern margin of UHPMB from the Dabie Mountains. Geochemical features indicate that the protoliths of the jadeite-quartzite and associated eclogite to be supracrustal rocks. The occurrence of micro-inclusions of coesite in jadeite and garnet confirmed that the continental crust can be subducted to great depth (8 0-100km) and then exhumed rapidly with its UHP mineral signature fairly preserved. Therefore, study of UHP jadeite-quartzite provides important information on subduction of continental crustal rocks and their exhumation histories, as well as the dynamics of plate tectonic processes at convergent margins. The purpose of this paper is to investigate the presence of hydrous component in the jadeite-quartzite belt, significant natural variations in the hydrous component content of UHP minerals and to discuss the role of water in petrology, geochemistry and micro-tectonic. On the basis of our previous studies, some new geological evidences have been found in the jadeite-quartzite belt by researches on petrography, mineralogy, micro-tectonic, hydrous component content of UHP minerals and combined with the study on rheology of materials using microprob, ER, TEM. By research and analysis of these phenomenona, the results obtained are as follows: 1. The existence of fluid during ultra-high pressure metamorphic process. Jadeites, omphacite, garnet, rutile, coesite and quartz from the jadeite-quartzite belt have been investigated by Fourier transform infrared spectrometer and TEM. Results show that all of these minerals contain trace amount of water which occur as hydroxyl and free-water in these minerals. The two-type hydrous components in UHP minerals are indicated stable in the mantle-depth. The results demonstrated that these ultra-high pressure metamorphic minerals, which were derived from continental crust protoliths, they could bring water into the mantle depth during the ultra-high pressure metamorphism. The clusters of water molecules within garnet are very important evidence of the existence of fluid during ultra-high pressure metamorphic process. It indicated that the metamorphic system was not "dry"during the ultra-high pressure stage. 2.The distribution of hydrous component in UHP minerals of jadeite-quartzite. The systematic distribution of hydrous components in UHP minerals are a strong indication that water in these minerals, are controlled by some factors and that the observed variations are not of a random nature. The distribution and concentration of hydrous component is not only correlated with composition of minerals, but also a function of geological environment. Therefore, the hydrous component in the minerals can not only take important part in the UHP metamorphic fluid during subduction of continental crustal rocks, but also their hydroxyl transported water molecules with decreasing pressure during their exhumation. And these water molecules can not only promote the deformation of jadeite through hydrolytic weakening, but also may be the part of the retrograde metamorphic fluid. 3.The role of water in the deformed UHP minerals. The jadeite, omphacite, garnet are strong elongated deformation in the jadeite-quartzite from the Dabie Mountains. They are (1) they are developed strong plastic deformation; (2) developed dislocation loop, dislocation wall; (3) the existence of clusters of water molecular in the garnet; and (4) the evolution of micero-tectonic from clusters of water molecular-dislocation loop in omphacite. That indicated that the water weakening controlled the mechanism of deformed minerals. Because the data presented here are not only the existence of clusters of water molecular in the garnet, but also developed strong elongation, high density of dislocation and high aspect ratios, adding microprobe data demonstrate the studied garnet crystals no compositional zoning. Therefore, this indicates that the diffusion process of the grain boundary mobility did not take place in these garnets. On the basis of above features, we consider that it can only be explained by plastic deformation of the garnets. The clusters of water molecules present in garnet was directly associated with mechanical weakening and inducing in plastic deformation of garnet by glissile dislocations. Investigate of LPO, strain analysis, TEM indicated that these clinopyroxenes developed strong elongation, high aspect ratios, and developed dislocation loop, dislocation wall and free dislocations. These indicated that the deformation mechanism of the clinopyroxenes plastically from the Dabie Mountains is dominant dislocation creep under the condition of the UHP metamorphic conditions. There are some bubbles with dislocation loops attached to them in the omphacite crystal. The bubbles attached to the dislocation loops sometimes form a string of bubble beads and some loops are often connected to one another via a common bubble. The water present in omphacite was directly associated with hydrolitic weakening and inducing in plastic deformation of omphacite by dislocations. The role of water in brittle deformation. Using microscopy, deformation has been identified as plastic deformation and brittle deformation in UHP minerals from the Dabie Mountains. The study of micro-tectonic on these minerals shows that the brittle deformation within UHP minerals was related to local stresses. The brittle deformation is interpreted as being caused by an interaction of high fluid pressure, volume changes. The hydroxyl within UHP minerals transported water molecules with decreasing pressure due to their exhumation. However, under eclogite facies conditions, the litho-static pressure is extreme, but a high fluid pressure will reduce the effective stress and make brittle deformation possible. The role of water in prograde metamorphism. Geochemical research on jadeite-quartzite and associated eclogite show that the protoliths of these rocks are supracrustal rocks. With increasing of temperature and pressure, the chlorite, biotite, muscovite was dehydrous reaction and released hydrous component during the subduction of continental lithosphere. The supracrustal rocks were transformed UHP rocks and formed UHP facies assemblage promotely by water introduction, and was retained in UHP minerals as hydrous component. The water within UHP minerals may be one of the retrograde metamorphic fluids. Petrological research on UHP rocks of jadeite-quartzite belt shows that there was existence of local fluids during early retrograde metamorphism. That are: (1) coronal textures and symplectite around relict UHP minerls crystals formed from UHP minerls by hydration reactions; (2) coronal textures of albite around ruitle; and (3) micro-fractures in jadeite or garnet were filled symplectite of Amp + PI + Mt. That indicated that the reactions of early retrograde metamorphism dependent on fluid introduction. These fluids not only promoted retrograde reaction of UHP minerals, but also were facilitate to diffuse intergranular and promote growth in minerals. Therefore, the hydrous component in the UHP minerals can not only take important part in the UHP metamorphic fluid during subduction of continental crustal rocks, but also their hydroxyl transport water molecules with decreasing pressure and may take part in the retrograde metamorphic fluid during their exhumation. 7. The role of water in geochemistry of UHP jadeite-quartzite. Geochemical research show that there are major, trace and rare earth element geochemical variations in the jadeite-quartzite from the Changpu district of Dabie Mountains, during retrograde metamorphic processes from the jadeite-quartzite--gneiss. The elements such as SiO_2、FeO、Ba、Zr、Ga、La、Ce、PTN Nd% Sm and Eu increase gradually from the jadeite-quartzite to retrograded jadeite-quartzite and to gneiss, whilst TiO_2. Na_2CK Fe2O_3、Rb、Y、Nb、Gd、Tb、Dy、Ho、Er、Tm、Yb decrease gradually. And its fO_2 keep nearly unchanged during early retrograde metamorphism, but decreased obviously during later retrograde metamorphism. These indicate that such changes are not only controlled by element transformation between mineralogical phases, but also closely relative to fluid-rock interaction in the decompression retrograde metamorphic processes.

东海榴辉岩向斜长角闪岩的转化过程

The Ultrahigh Pressure Metamorphic (UHPM) eclogite, which was resulted from deep subduction of crustal continent, is very significant due to its continental dynamic implications. Further more, this kind of rocks experienced great P-T, fluid and stresses changes during its forming and exhumation, causing mineral reactions occur intensively, which resulted in a lot of fantastic micro-texture. The micro-texture was preserved duo to a rapid exhumation of the eclogite. This PhD dissertation takes such micro-textures in 10 Donghai eclogite samples South Sulu UHPM terrene, as research object to reveal the transformation of the eclogite to amphibolite. Microscope and Scanning Electron Microscope were employed to observe the micro-texture. Basing on microprobe analysis of minerals, the ACF projections and iso-con analysis were used to uncover the mineral reactions during the transformation. Micro-texture observation (both of Microcopy and Electron Scanning Microscope), demonstrated: l.The peak mineral assemblage of the researched Donghai eclogites is garnet + omphacite + rutile (+ kyanite + aptite +coesite). 2.The transformation of the Donghai eclogite to amphibolite can be divided into two stages: The earlier one is Symplectization, resulting in the forming of diopside + albite (+magnetite) symplectite that occurred only along the boundary between two adjacent omphacite grains. Other minerals were not involved in such reaction. The latter stage is Fluid-Infiltration of the eclogite, which was caused by fluid-intrusion. The infiltration is demonstrated by amphibolization of the symplectite, decomposition of garnet and the forming of some hydrous minerals such as phengite and epidote, and resulted in an amphibole + plagioclase + phengite + epidote or ziosite assemblage. Basing on microprobe analysis of the minerals, ACF projections indicated: In the ACF diagrams, the two joint lines of peak Grt + Omp and Dio + Ab crossed at Omp projection-point, indicating that the garnet had not taken part in the forming reaction of the Dio + Ab symplectite, just like that had been pointed out by micro-texture observation. In the ACF diagrams, the hornblende + plagioclase + epidote + phengite quadrilateral intersected with Dio + Ab + Grt triangle, demonstrating that the hydrous mineral assemblage was formed by fluid infiltration through garnet, diopside and albite. Iso-con (mass-balance) analysis of the symplectization and infiltration reveals: 1.The symplectization of the omphacite has a very complex mass exchange: Some symplectite gained only silicon from its surroundings; and some one requires Ca, but provides Na to its surroundings; while other symplectite provides Ca, Mg and Fe to its surroundings. 2.The infiltration cause variable mass exchanges occurring among the garnet, diopside and albite: In some eclogite sample, no mass, except H2O, exchange occurred during the infiltration. Meanwhile, there was not any hydrous mineral except hornblende formed in the sample accordingly. In some samples, the mass exchange among the three minerals is complex: amphibolization of the diopside in a symplectite gained Al from garnet, and provided Si and Ca to its surrounding, resulting in a Si, Ca and Al-rich fluid. Correspondingly, there was a lot of phengite and ziosite occurred in the sample. In other samples, the amphibolization of a symplectite provided Fe and Mg besides Si and Ca to its surrounding while gained Al. In such kind of sample, epidote occurred within the hydrous mineral assemblage. Synthesizing the micro-texture observation, ACF analysis and iso-con analysis, we deduced the transformation procedure as following: 1. A symplectite after an omphacite was resulted by one, or two, or all of following mineral reactions together: Jd (Ca-Tsch) +SiO2=Ab (An) (1) 4NaA IS i.A+CaO=2NaAlS i308+Na20+CaAl2S 1208 (2) 2NaAlSi2OB (Jd in Omp)+CaMgSi;,0B(Dio in Omp)-2NaAlSi:,O"(Ab)+Ca0+Mg0 (3) 2(CaAl2Si0fi) (Ca-tsch in Omp)+CaFeSi2O6(Hed in 0mp)-H>2CaAl2Si208(An)+Ca0 + FeO (4) A CO2-rich fluid is suggested as cataclysm for the above reactions, which largely increased the mobility of Ca, Mg and Na resulted from reaction (2), (3) and (4). The immobile product Fe2* combined with rutile to form ilmenite, resulting in rutile + ilmenite symplectite. Or, the Fe was precipitated as hematite locally. A procedure of the fluid infiltration as following is suggested: I .A hydrous fluid intruded into the eclogite, and reacted first with garnet to form hornblende and extra Al, resulting in a hornblende film around the garnet grain and an Al-rich fluid. 2.The Al-rich fluid infiltrated through the symplectite, OH" and part of the Al in the fluid combined with Dio while some Si and Ca in the Dio were dissolved made the Dio transferred to amphibole. Meanwhile, plagioclase-type cation exchange occurred between the fluid and plagioclase in the symplectite, making the plagioclase have a higher An-content. 3.Above infiltration and cation exchange resulted in an Al, Si, Ca (and K, providing the primary hydrous fluid contain K)-rich fluid. 4.Under suitable conditions, the solute in the fluid precipitated to form phengite firstly. After the K element in the fluid was consumed up, ziosite or epidote was formed. If the fluid did not contain any K. element, only ziosite or epidote was precipitated. For those eclogites, where all omphacite had been replaced by symplectite before infiltration, neither element exchange occurred, nor did phengite or epidote form during the infiltration. At the last stage, the garnet was oxidized and breakdown: garnet + H2O = epidote + hornblende + hematite, due to more and more fluid intruding into the eclogite. At this time, all the peak minerals were replaced by amphibolite-phase ones, and the eclogite transformed to an amphibolite completely. Tentative pressure calculation indicates that the infiltration occurred at 3-6kbar (about 10-20km depth), where the deformation mechanics transformed from brittle to ductile yield. At such depth, the surface water can permeate the rocks through fault system, causing a rapid cooling.

高温高压和不同氧逸度条件下斜方辉石电导率的实验研究

在1．0～4．0GPa和1073～1423K及不同的氧分压条件下，借助YJ-3000t紧装式六面顶高压设备和Sarltron-1260阻抗／增益-相位分析仪，就位测定了斜方辉石的电导率。氧逸度控制由Ni＋NiO、Fe＋Fe3O4、Fe＋FeO和Mo＋MoO2四种固态氧缓冲剂完成的。实验结果表明：①在所选择的频率范围内（10^-1～10^6Hz），复阻抗对频率有很强的依赖性;②随着温度（T）升高，电导率（σ）增大，logσ与1／T之间符合Arrenhius关系.

高温高压和不同氧逸度控制下单晶橄榄石电导率的实验研究

在1．0—4．0GPa，1123—1473K和控制氧逸度（Ni＋NiO，Fe＋Fe3O4，Fe＋FeO和Mo＋MoO2等4种氧缓冲剂）的条件下，借助YJ-3000t紧装式六面顶高温高压设备和Sarhron-1260阻抗／增益-相位分析仪，就位测定了橄榄石的电导率．实验结果表明：（1）在测定的频率范围（10^3-10^6Hz），样品的电导率对频率具有很强的依赖性；（2）随着温度（T）升高，电导率（σ）增大，lgσ与1／T之间符合Arrhenius关系；（3）在Fe＋Fe3O4氧缓冲条件下，随着压力升高，电导率降低，而活化焓和指前因子增大，并给出样品的活化能和活化体积分别为（1．25±0．08）eV和（0．105±0．025）cm^3·mol；（4）在给定的压力和温度下，随着氧逸度增加，电导率增大，活化焓降低；（5）小极化子导电机制可为橄榄石在高温高压下的导电行为提供合理的解释.

渔塘坝硒矿硅质岩的地球化学特征及成因

渔塘坝硒矿床是目前我国发现含硒量（8590×10^-6）最高的小型独立硒矿床，其赋矿岩石主要为硅质岩，且发育程度较高。早二叠世晚期的黑色碳质硅质岩系，是区内的赋矿层位，它局限于特定的沉积相位，即碳酸盐合地海盆浅部沼泽（藻沼）环境沉积的黑色碳质硅质岩相带，硒矿化层和这套碳质硅质岩相带密切相关，其矿化相带呈NW向展布。硅质岩的SiO2含量变化较大（64.2%-94.85％），平均为75.9%;Fe2O3、Fe2O3、FeO、MnO、TiO2、Al2O3和MgO等含量相对，与其它热水成因硅质岩相近；硅质岩富含As、Sb、Fe和Ag，而贫Cu、Co和Ni；在Al-Fe-(Cu+Co+Ni)三角图、U-Th相关图和P2O3-Y相关图上的投影特征，也同样显示出硅质岩的热水成因特征。另本区硅质岩中的Cr含量较大，且（Fe+Mn）/Ti的比值为6.34，这表明硅质岩在成因上还可能和二叠纪峨眉山玄武岩喷发的火山作用有一定的联系。