Análise das resistências de embutimento e de compressão para madeiras de pinus e eucalipto

The connections in the wood structures are the places with high concentrations of stresses and therefore are more fragile than the rest of the structure. The connections between pieces of wood can be made by metal pins (nails or screws). The compression and embedment strength has significant influence on the calculation of the connections. The main aim of this work was to evaluate the compression and embedment strength in the directions parallel, inclined at 45° and normal to the grain, using standard specimens according to ABNT NBR 7190/1997 standard. The compression and embedment strength were initially evaluated according to ABNT NBR 7190/1997, which admits the deformation of 2‰ as limit of embedment and the ratio between the ultimate strength and the area of application of load in the specimen for the compressive strength. Afterward, the embedment strength was evaluated by the EUROCEDE 5 /1995 European standard, which use the limit of 5 mm of the displacement for the embedment. Specimens of Pinus oocarpa, Cumaru and Pinus taeda were used in tests to calibration of equipment and specimens of Pinus taeda and Eucalipto citriodora were used to compare the results of strength. The results of strength were evaluated based on statistical analysis. The results of compressive strength for the Pinus taeda showed no significant differences in embedment strength in the directions parallel and normal to the grain. For the Eucalipto citriodora only in the direction parallel to grain the compression strength was not significant compared with the embedment strength. For both species, only the parallel compression strength and inclined at 45o to the grain, which were to the grain, which were admitted the strain of 2‰ were not significantly different compared with the compression strength determined according to ABNT NBR 7190/1997. The normal compression strength obtained according to ABNT NBR 7190/1997 and ultimate compression strength not ...

Verificação de pilares metálicos compostos constituídos por perfis formados a frio por meio de programa computacional

In this work, we discuss the procedures adopted for the design of built-up columns (laced and battened columns). Built-up columns are widely used in steel construction generally when the compression forces are relatively low and the column buckling lengths are large. They are commonly used in industrial buildings, for example, as posts for cladding, or as columns supporting a crane girder. Unlike columns with full section, in the case of built-up columns, it is necessary to evaluate the shear stiffness. In fact, the shear strength leads to a significant reduction of the critical load. In the context of this work, the components of the columns (chords, diagonals, posts, etc.) are formed by cold-formed members. In order to systematize and rationalize the verification of the built-up columns, this work aim to develop a computer program based on the standards NBR 14762, NBR 6355 and Eurocode 3, basically the considerations of the part EN 1993-1-1

Verificação de pilares metálicos compostos constituídos por perfis formados a frio por meio de programa computacional

In this work, we discuss the procedures adopted for the design of built-up columns (laced and battened columns). Built-up columns are widely used in steel construction generally when the compression forces are relatively low and the column buckling lengths are large. They are commonly used in industrial buildings, for example, as posts for cladding, or as columns supporting a crane girder. Unlike columns with full section, in the case of built-up columns, it is necessary to evaluate the shear stiffness. In fact, the shear strength leads to a significant reduction of the critical load. In the context of this work, the components of the columns (chords, diagonals, posts, etc.) are formed by cold-formed members. In order to systematize and rationalize the verification of the built-up columns, this work aim to develop a computer program based on the standards NBR 14762, NBR 6355 and Eurocode 3, basically the considerations of the part EN 1993-1-1

Reliability of buildings in service limit state for maximum horizontal displacements

Brazilian design code ABNT NBR6118:2003 - Design of Concrete Structures - Procedures - [1] proposes the use of simplified models for the consideration of non-linear material behavior in the evaluation of horizontal displacements in buildings. These models penalize stiffness of columns and beams, representing the effects of concrete cracking and avoiding costly physical non-linear analyses. The objectives of the present paper are to investigate the accuracy and uncertainty of these simplified models, as well as to evaluate the reliabilities of structures designed following ABNT NBR6118:2003[1&] in the service limit state for horizontal displacements. Model error statistics are obtained from 42 representative plane frames. The reliabilities of three typical (4, 8 and 12 floor) buildings are evaluated, using the simplified models and a rigorous, physical and geometrical non-linear analysis. Results show that the 70/70 (column/beam stiffness reduction) model is more accurate and less conservative than the 80/40 model. Results also show that ABNT NBR6118:2003 [1] design criteria for horizontal displacement limit states (masonry damage according to ACI 435.3R-68(1984) [10]) are conservative, and result in reliability indexes which are larger than those recommended in EUROCODE [2] for irreversible service limit states.

Modelización por métodos numéricos de la degradación térmica de un elemento estructural de madera en situación de incendio

La cuantificación de la reducción de las propiedades resistentes y de la sección de un elemento estructural en situación de incendio es fundamental de cara a garantizar la estabilidad estructural en situación de incendio. Existen investigaciones que tratan de determinar la variación de las propiedades térmicas y mecánicas de la madera sometida a cargas térmicas, y la reducción de sección transversal de un elemento estructural de madera. La normativa europea en materia de construcción con madera, el Eurocódigo 5, propone unas simplificaciones para determinar la sección residual de un elemento estructural de madera en situación de incendio. Los objetivos de este trabajo comprenden una revisión de algunos trabajos realizados en el campo de la variación en función de la temperatura de las propiedades térmicas de la madera (calor específico, densidad y conductividad térmica), y la construcción con los distintos valores propuestos de varios modelos de elementos finitos que se someterán a cargas térmicas definidas por la curva ISO 834-1. Los resultados se compararán con un modelo construido con los valores que el Eurocódigo propone y con un ensayo experimental. Como resultado final, se propone finalmente un modelo de elementos finitos que emule el comportamiento del ensayo experimental. The quantification of the decrease of strength properties and section of a structural element in a fire situation is critical in order to guarantee the structural stability in such a fire event. There are some researches in literature trying to find the variation of thermal and mechanical properties of wood subjected to thermal loads, and the decrease of cross section of a wooden structural element. The European legislation on timber construction, Eurocode 5, proposes a simplification to determine the residual section of a wooden structural element in a fire situation. This paper objectives consist in a review of some researches in the field of variations, depending on the temperature, of the thermal properties of wood (specific heat, density and thermal conductivity); and in the construction of a few finite element models of timber structural elements affected by thermal loads according to ISO 834-1. The results were compared with a model based in Eurocode 5 and with an experimental test. As final result, at last, we propose a finite element model that simulates the behavior of the experimental tested element.

Study of the evolution of the seismic cycle of stress and strain associated to the El Salvador Fault Zone

• Central America: – Regional studies in Central America (Seismic Hazard). – El Salvador Fault Zone (ESFZ). – Aguacaliente‐Navarro Fault Zone (ANFZ), Central Valley of Costa Rica. – Haiti (seismic hazard) • Spain: – Regional‐Nacional studies of seismic hazards (applications to building codes, eurocode, emergency plans, etc.) – Betic range zone, south of Spain. – Ibero‐Maghrebi region (collision zone)

Structural behaviour and design criteria of under-deck cable-stayed bridges subjected to seismic action

Under-deck cable-stayed bridges are very effective structural systems for which the strong contribution of the stay cables under live loading allows for the design of very slender decks for persistent and transient loading scenarios. Their behaviour when subjected to seismic excitation is investigated herein and a set of design criteria are presented that relate to the type and arrangement of bearings, the number and configuration of struts, and the transverse distribution of stay cables. The nonlinear behaviour of these bridges when subject to both near-field and far-field accelerograms has been thoroughly investigated through the use of incremental dynamic analyses. An intensity measure that reflects the pertinent contributions to response when several vibration modes are activated was proposed and is shown to be effective for the analysis of this structural type. The under-deck cable-stay system contributes in a very positive manner to reducing the response when the bridges are subject to very strong seismic excitation. For such scenarios, the reduction in the stiffness of the deck because of crack formation, when prestressed concrete decks are used, mobilises the cable system and enhances the overall performance of the system. Sets of natural accelerograms that are compliant with the prescriptions of Eurocode 8 were also applied to propose a set of design criteria for this bridge type in areas prone to earthquakes. Particular attention is given to outlining the optimal strategies for the deployment of bearings

Dynamic response of underpasses for high-speed train lines

Underpasses are common in modern railway lines. Wildlife corridors and drainage conduits often fall into this category of partially buried structures. Their dynamic behavior has received far less attention than that of other structures such as bridges, but their large number makes their study an interesting challenge from the viewpoint of safety and cost savings. Here, we present a complete study of a culvert, including on-site measurements and numerical modeling. The studied structure belongs to the high-speed railway line linking Segovia and Valladolid in Spain. The line was opened to traffic in 2004. On-site measurements were performed for the structure by recording the dynamic response at selected points of the structure during the passage of high-speed trains at speeds ranging between 200 and 300 km/h. The measurements provide not only reference values suitable for model fitting, but also a good insight into the main features of the dynamic behavior of this structure. Finite element techniques were used to model the dynamic behavior of the structure and its key features. Special attention is paid to vertical accelerations, the values of which should be limited to avoid track instability according to Eurocode. This study furthers our understanding of the dynamic response of railway underpasses to train loads.

Shaking table tests of structures with hysteretic dampers: experimental results vs. prediction using non-linear static methods

The use of seismic hysteretic dampers for passive control is increasing exponentially in recent years for both new and existing buildings. In order to utilize hysteretic dampers within a structural system, it is of paramount importance to have simplified design procedures based upon knowledge gained from theoretical studies and validated with experimental results. Non-linear Static Procedures (NSPs) are presented as an alternative to the force-based methods more common nowadays. The application of NSPs to conventional structures has been well established; yet there is a lack of experimental information on how NSPs apply to systems with hysteretic dampers. In this research, several shaking table tests were conducted on two single bay and single story 1:2 scale structures with and without hysteretic dampers. The maximum response of the structure with dampers in terms of lateral displacement and base shear obtained from the tests was compared with the prediction provided by three well-known NSPs: (1) the improved version of the Capacity Spectrum Method (CSM) from FEMA 440; (2) the improved version of the Displacement Coefficient Method (DCM) from FEMA 440; and (3) the N2 Method implemented in Eurocode 8. In general, the improved version of the DCM and N2 methods are found to provide acceptable accuracy in prediction, but the CSM tends to underestimate the response.

Estudio comparativo en el dimensionamiento de cimentaciones

El presente documento es el resultado de la participación de forma activa del autor en el equipo de la oficina de proyectos IDEAM S.A. encargada de realizar en U.T.E. con F.H.E.C.O.R. un manual de aplicación del Eurocódigo 7 a petición de la Dirección General de Carreteras del Ministerio de Fomento. El trabajo se ha centrado en la comparación entre las diversas formulaciones existentes para obtener la carga de hundimiento en cimentaciones superficiales, comparando los resultados de los distintos factores que participan en la formulación de los diferentes autores. De este modo el estudio ha servido para detectar algunas incongruencias entre las formulaciones clásicas de Brinch-Hansen y la formulación propuesta en el anexo D del Eurocódigo 7 (UNE-EN 1997-1) A sí mismo la investigación también se centra en las implicaciones que supone realizar el diseño de las cimentaciones superficiales utilizando para ello el método de los coeficientes parciales de seguridad y combinaciones de acciones mayoradas tal y como plantea el Eurocódigo 7 en lugar de realizar dicho diseño mediante el método de los coeficientes globales de seguridad y combinaciones características de acciones en la forma en que la tradición geotécnica española ha venido haciendo hasta la fecha. This document is the result of the active participation of the author in IDEAM SA, responsible for compiling a guide for the Eurocode 7 as a request by General Director of Hihways of the Fomento Ministry The work primarily focuses on the comparison between the different theories used to obtain the bearing capacity of shallow foundations and comparing the results of the multpile factors involved in the formulas designed by different authors Thereby, the present study has helped identify inconsistencies between the classical formulations of Brinch-Hansen and the proposed formulation in the Annex D of the Eurocode 7 (UNE- EN 1997-1) The investigation additionally focuses on the implications of shallow foundations desing by using the method of partial safety factors and the ULS combinations of actions instead of employing the design by the global safety factor method and SLS combinations of the actions.

Measuring dynamic effects on underpasses of high-speed railway lines

Underpasses are common in modern railway lines. Wildlife corridors and drainage conduits often fall into this category of partially buried structures. Their dynamic behaviour has received far less attention than that of other structures such as bridges, but their large number makes their study an interesting challenge in order to achieve safe and cost-effective structures. As ballast operations are a key life cycle cost, and excessive vibrations increase the need of ballast regulation in order to ensure track geometry, special attention is paid to accelerations, the values of which should be limited to avoid track instability according to Eurocode. In this paper, the data obtained during on site measurements on culverts belonging to a Spanish high-speed train line are presented. A set of six rectangular-shaped, closed-frame underpasses were monitored under traffic loading. Acceleration records at different points of the structures are presented and discussed. They reveal a non-uniform dynamic response of the roof-slab, with the highest observed values below the occupied track. Also, they indicate that the dynamic response is important up to frequencies higher than those usually observed for standard simply supported bridges. Finally, they are used to obtain a heuristic rule to estimate acceleration levels on the roof-slab.

Moment transfer and influence of transverse beams in interior waffle flat plate-column connections under lateral loading

This paper addresses two aspects of the behavior of interior reinforced concrete waffle flat plate?column connections under lateral loads: the share of the unbalanced moment between flexure and excentric shear, and the effect of the transverse beams. A non-linear finite element model (benchmark model) was developed and calibrated with the results of quasi-static cyclic tests conducted on a 3/5 scale specimen. First, from this numerical model, the portion cv of the unbalanced moment transferred by the excentricity of shear about the centroid of the critical sections defined by Eurocode 2 (EC-2) and by ACI 318-11 was calculated and compared with the share-out prescribed by these codes. It is found that while the critical section of EC-2 is consistent with the cv provided by this code, in the case of ACI 318-11, the value assigned to cv is far below (about 50% smaller) the actual one obtained with the numerical simulations. Second, from the benchmark model, seven additional models were developed by varying the depth D of the transverse beam over the thickness h of the plate. It was found that the ductility of the connection and the effective width of the plate can respectively be increased up to 50% and 10% by raising D/h to 2 and 1.5.

Effect of fire on the microstructure and mechanical response of structural steels for building construction

The research is an exhaustive study of the microstructure and of the stress-strain curves of structural steel S460N at temperatures typical of a fire. It includes a fractographic study of the fracture suifaces of cylindrical specimens, tensile tested at different fire scenarios, explaining the relationship between the failure micromechanisms and temperature. The paper ends with the comparison between the experimentally found strain-stress curves with that one's proposed by the EUROCODE EC3, resulting that in the case of steel S460N these are on the side ofsafety.

Effect of fire on the microstructure and mechanical response of structural steels for building construction

The research is an exhaustive study of the microstructure and of the stress-strain curves of structural steel S460N at temperatures typical of a fire. It includes a fractographic study of the fracture suifaces of cylindrical specimens, tensile tested at different fire scenarios, explaining the relationship between the failure micromechanisms and temperature. The paper ends with the comparison between the experimentally found strain-stress curves with that one's proposed by the EUROCODE EC3, resulting that in the case of steel S460N these are on the side ofsafety.

Fórmulas para el cálculo del factor de impacto de estructuras semienterradas en líneas de ferrocarril de alta velocidad = Dynamic factors for underpasses in high speed train lines

Los pasos inferiores son muy numerosos en las líneas de ferrocarril. Su comportamiento dinámico ha recibido mucha menos atención que el de otras estructuras como los puentes, pero su elevado número hace que su estudio sea económicamente relevante con vista a optimizar su forma, manteniendo la seguridad. El proyecto de puentes según el Eurocódigo incluye comprobaciones de estados límite de tensiones bajo carga dinámica. En el caso de pasos inferiores, las comprobaciones pueden resultar tan costosas como aquellas de puentes, pese a que su coste es mucho menor. Por tanto, se impone la búsqueda de unas reglas de cálculo simplificado que pongan en consonancia el coste de la estructura con el esfuerzo necesario para su proyecto. Este artículo propone un conjunto de reglas basadas en un estudio paramétrico = Underpasses are common in modern railway lines. Wildlife corridors and drainage conduits often fall into this category of partially buried structures. Their dynamic behavior has received far less attention than that of other structures such as bridges, but their large number makes their study an interesting challenge from the viewpoint of safety and cost savings. The bridge design rules in accordance with the Eurocode involve checks on stresses according to dynamic loading. In the case of underpasses, those checks may be as much as those for bridges. Therefore, simplified design rules may align the design effort with their cost. Such a set of rules may provide estimations of response parameters based on the key parameters influencing the result. This paper contains a proposal based on a parametric study.