An experimental research investigation into disused flat rail wagons as bridges with applications for low volume rural roads in Australia

An experimental laboratory investigation was carried out to assess the structural adequacy of a disused PHO Class Flat Bottom Rail Wagon (FRW) for a single lane low volume road bridge application as per the design provisions of the Australian Bridge Design Standard AS 5100(2004). The investigation also encompassed a review into the risk associated with the pre-existing damage in wagons incurred during their service life on rail. The main objective of the laboratory testing of the FRW was to physically measure its performance under the same applied traffic loading it would be required to resist as a road bridge deck. In order to achieve this a full width (5.2m) single lane, single span (approximately 10m), simply supported bridge would be required to be constructed and tested in a structural laboratory. However, the available clear spacing between the columns of the loading portal frame encountered within the laboratory was insufficient to accommodate the 5.2m wide bridge deck excluding clearance normally considered necessary in structural testing. Therefore, only half of the full scale bridge deck (single FRW of width 2.6m) was able to be accommodated and tested; with the continuity of the bridge deck in the lateral direction applied as boundary constraints along the full length of the FRW at six selected locations. This represents a novel approach not yet reported in the literature for bridge deck testing to the best of the knowledge of the author. The test was carried out under two loadings provided in AS 5100 (2004) – one stationary W80 wheel load and the second a moving axle load M1600. As the bridge investigated in the study is a single lane single span low volume road bridge, the risk of pre-existing damage and the expected high cycle fatigue failure potential was assessed as being minimal and hence the bridge deck was not tested structurally for fatigue/ fracture. The high axle load requirements have instead been focussed upon the investigation into the serviceability and ultimate limit state requirements. The testing regime adopted however involved extensive recording of strains and deflections at several critical locations of the FRW. Three locations of W80 point load and two locations of the M1600 Axle load were considered for the serviceability testing; the FRW was also tested under the ultimate load dictated by the M1600. The outcomes of the experimental investigation have demonstrated that the FRW is structurally adequate to resist the prescribed traffic loadings outlaid in AS 5100 (2004). As the loading was directly applied on to the FRW, the laboratory testing is assessed as being significantly conservative. The FRW bridge deck in the field would only resist the load transferred by the running platform, where, depending on the design, composite action might exist – thereby the share of the loading which needs to be resisted by the FRW would be smaller than the system tested in the lab. On this basis, a demonstration bridge is under construction at the time of writing this thesis and future research will involve field testing in order to assess its performance.

A longitudinal study of corporate earnings guidance in Australia’s continuous disclosure environment

Since the introduction of a statutory‐backed continuous disclosure regime (CDR) in 1994, regulatory reforms have significantly increased litigation risk in Australia for failure to disclose material information or for false and misleading disclosure. However, there is almost no empirical research on the impact of the reforms on corporate disclosure behaviour. Motivated by the absence of research and using management earnings forecasts (MEFs) as a disclosure proxy, this study examines (1) why managers issue earnings forecasts, (2) what firm‐specific factors influence MEF characteristics, and (3) how MEF behaviour changes as litigation risk increases. Based on theories in information economics, a theoretical framework for MEF behaviour is formulated which includes antecedent influencing factors related to firms‟ internal and external environments. Applying this framework, hypotheses are developed and tested using multivariate models and a large sample of hand-collected MEFs (7,213) issued by top 500 ASX-listed companies over the 1994 to 2008 period. The results reveal strong support for the hypotheses. First, MEFs are issued to reduce information asymmetry, litigation risk and signal superior performance. Second, firms with better financial performance, smaller earnings changes, and lower operating uncertainty provide better quality MEFs. Third, forecast frequency and quality (accuracy, timeliness and precision) noticeably improve as litigation risk increases. However, managers appear to be still reluctant to disclose earnings forecasts when there are large earnings changes, and an asymmetric treatment of news type continues to prevail (a good news bias). Thus, the findings generally provide support for the effectiveness of the CDR regulatory reforms in improving disclosure behaviour and will be valuable to market participants and corporate regulators in understanding the implications of management forecasting decisions and areas for further improvement.

Corporate governance mechanisms and earnings management in transitional countries – evidence from Chinese listed firms

The objective of this thesis is to investigate whether the corporate governance practices adopted by Chinese listed firms are associated with the quality of earnings information. Based on a review of agency and institutional theory, this study develops hypotheses that predict the monitoring effectiveness of the board and the audit committee. Using a combination of univariate and multivariate analyses, the association between corporate governance mechanisms and earnings management are tested from 2004 to 2008. Through analysing the empirical results, a number of findings are summarised as below. First, board independence is weakened by the introduction of government officials as independent directors on the boards. Government officials acting as independent directors, claim that they meet the definition of independent director set by the regulation. However, they have some connection with the State, which is the controlling shareholder in listed SOEs affiliated companies. Consequently, the effect of the independent director’s expertise in constraining earnings management is mitigated as demonstrated by an insignificant association between board expertise and earnings management. An alternative explanation for the inefficiency of board independence may point to the pre-selection of independent directors by the powerful CEO. It is argued that a CEO can manipulate the board composition and choose the "desirable" independent directors to monitor themselves. Second, a number of internal mechanisms, such as board size, board activities, and the separation of the roles of the CEO and chair are found to be significantly associated with discretionary accruals. This result suggests that there are advantages in having a large and active board in the Chinese setting. This can offset the disadvantages associated with large boards, such as increased bureaucracy, and hence, increase the constraining effects of a large and resourceful board. Third, factor analysis identifies two factors: CEO power and board power. CEO power is the factor which consists of CEO duality and turnover, and board power is composed of board size and board activity. The results of CEO power show that if a Chinese listed company has CEO duality and turnover at the same time, it is more likely to have a high level of earnings management. The significant and negative relationship between board power and accruals indicate that large boards with frequent meetings can be associated with low level of earnings management. Overall, the factor analysis suggests that certain governance mechanisms complement each other to become more efficient monitors of opportunistic earnings management. A combination of board characteristics can increase the negative association with earnings management. Fourth, the insignificant results between audit committees and earnings management in Chinese listed firms suggests that the Chinese regulator should strengthen the audit committee functions. This thesis calls for listed firms to disclose more information on audit committee composition and activities, which can facilitate future research on the Chinese audit committee’s monitoring role. Fifth, the interactive results between State ownership and board characteristics show that dominant State ownership has a moderating effect on board monitoring power as the State totally controls 42% of the issued shares. The high percentage of State ownership makes it difficult for the non-controlling institutional shareholders to challenge the State’s dominant status. As a result, the association between non-controlling institutional ownership and earnings management is insignificant in most situations. Lastly, firms audited by the international Big4 have lower abnormal accruals than firms audited by domestic Chinese audit firms. In addition, the inverse U-shape relationship between audit tenure and earnings quality demonstrates the changing effects of audit quality after a certain period of appointment. Furthermore, this thesis finds that listing in Hong Kong Stock Exchanges can be an alternative governance mechanism to discipline Chinese firms to follow strict Hong Kong listing requirements. Management of Hong Kong listed companies are exposed to the scrutiny of international investors and Hong Kong regulators. This in turn reduces their chances of conducting self-interested earnings manipulation. This study is designed to fill the gap in governance literature in China that is related to earnings management. Previous research on corporate governance mechanisms and earnings management in China is not conclusive. The current research builds on previous literature and provides some meaningful implications for practitioners, regulators, academic, and international investors who have investment interests in a transitional country. The findings of this study contribute to corporate governance and earnings management literature in the context of the transitional economy of China. The use of alternative measures for earnings management yields similar results compared with the accruals models and produces additional findings.

The impact of regulatory reforms on the earnings forecasting behaviour of IPO firms

Purpose – The purpose of this paper is to jointly assess the impact of regulatory reform for corporate fundraising in Australia (CLERP Act 1999) and the relaxation of ASX admission rules in 1999, on the accuracy of management earnings forecasts in initial public offer (IPO) prospectuses. The relaxation of ASX listing rules permitted a new category of new economy firms (commitments test entities (CTEs))to list without a prior history of profitability, while the CLERP Act (introduced in 2000) was accompanied by tighter disclosure obligations and stronger enforcement action by the corporate regulator (ASIC). Design/methodology/approach – All IPO earnings forecasts in prospectuses lodged between 1998 and 2003 are examined to assess the pre- and post-CLERP Act impact. Based on active ASIC enforcement action in the post-reform period, IPO firms are hypothesised to provide more accurate forecasts, particularly CTE firms, which are less likely to have a reasonable basis for forecasting. Research models are developed to empirically test the impact of the reforms on CTE and non-CTE IPO firms. Findings – The new regulatory environment has had a positive impact on management forecasting behaviour. In the post-CLERP Act period, the accuracy of prospectus forecasts and their revisions significantly improved and, as expected, the results are primarily driven by CTE firms. However, the majority of prospectus forecasts continue to be materially inaccurate. Originality/value – The results highlight the need to control for both the changing nature of listed firms and the level of enforcement action when examining responses to regulatory changes to corporate fundraising activities.

Designing and evaluating mobile multimedia user experiences in public urban places : Making sense of the field

The majority of the world’s population now lives in cities (United Nations, 2008) resulting in an urban densification requiring people to live in closer proximity and share urban infrastructure such as streets, public transport, and parks within cities. However, “physical closeness does not mean social closeness” (Wellman, 2001, p. 234). Whereas it is a common practice to greet and chat with people you cross paths with in smaller villages, urban life is mainly anonymous and does not automatically come with a sense of community per se. Wellman (2001, p. 228) defines community “as networks of interpersonal ties that provide sociability, support, information, a sense of belonging and social identity.” While on the move or during leisure time, urban dwellers use their interactive information communication technology (ICT) devices to connect to their spatially distributed community while in an anonymous space. Putnam (1995) argues that available technology privatises and individualises the leisure time of urban dwellers. Furthermore, ICT is sometimes used to build a “cocoon” while in public to avoid direct contact with collocated people (Mainwaring et al., 2005; Bassoli et al., 2007; Crawford, 2008). Instead of using ICT devices to seclude oneself from the surrounding urban environment and the collocated people within, such devices could also be utilised to engage urban dwellers more with the urban environment and the urban dwellers within. Urban sociologists found that “what attracts people most, it would appear, is other people” (Whyte, 1980, p. 19) and “people and human activity are the greatest object of attention and interest” (Gehl, 1987, p. 31). On the other hand, sociologist Erving Goffman describes the concept of civil inattention, acknowledging strangers’ presence while in public but not interacting with them (Goffman, 1966). With this in mind, it appears that there is a contradiction between how people are using ICT in urban public places and for what reasons and how people use public urban places and how they behave and react to other collocated people. On the other hand there is an opportunity to employ ICT to create and influence experiences of people collocated in public urban places. The widespread use of location aware mobile devices equipped with Internet access is creating networked localities, a digital layer of geo-coded information on top of the physical world (Gordon & de Souza e Silva, 2011). Foursquare.com is an example of a location based 118 Mobile Multimedia – User and Technology Perspectives social network (LBSN) that enables urban dwellers to virtually check-in into places at which they are physically present in an urban space. Users compete over ‘mayorships’ of places with Foursquare friends as well as strangers and can share recommendations about the space. The research field of Urban Informatics is interested in these kinds of digital urban multimedia augmentations and how such augmentations, mediated through technology, can create or influence the UX of public urban places. “Urban informatics is the study, design, and practice of urban experiences across different urban contexts that are created by new opportunities of real-time, ubiquitous technology and the augmentation that mediates the physical and digital layers of people networks and urban infrastructures” (Foth et al., 2011, p. 4). One possibility to augment the urban space is to enable citizens to digitally interact with spaces and urban dwellers collocated in the past, present, and future. “Adding digital layer to the existing physical and social layers could facilitate new forms of interaction that reshape urban life” (Kjeldskov & Paay, 2006, p. 60). This methodological chapter investigates how the design of UX through such digital placebased mobile multimedia augmentations can be guided and evaluated. First, we describe three different applications that aim to create and influence the urban UX through mobile mediated interactions. Based on a review of literature, we describe how our integrated framework for designing and evaluating urban informatics experiences has been constructed. We conclude the chapter with a reflective discussion on the proposed framework.

An evaluation framework for assessing the impact of public bicycle share schemes

INTRODUCTION • Public bicycle share schemes have emerged as a method of increasing rates of bicycle riding. • The overwhelming majority of schemes have begun since 2005, taking advantage of various tracking and payment technologies making short term rental practical and affordable. • Very little research has been undertaken to determine their potentially broad impact on transport behaviour and consequently, it is difficult to understand the performance of these schemes in terms of reduced emissions and congestion, as well as possible increases in physical activity.

Development of a high-speed sensing and detection system for automatic removal of packages with leaky seals from a high-speed food processing and packaging line

Contamination of packaged foods due to micro-organisms entering through air leaks can cause serious public health issues and cost companies large amounts of money due to product recalls, consumer impact and subsequent loss of market share. The main source of contamination is leaks in packaging which allow air, moisture and microorganisms to enter the package. In the food processing and packaging industry worldwide, there is an increasing demand for cost effective state of the art inspection technologies that are capable of reliably detecting leaky seals and delivering products at six-sigma. The new technology will develop non-destructive testing technology using digital imaging and sensing combined with a differential vacuum technique to assess seal integrity of food packages on a high-speed production line. The cost of leaky packages in Australian food industries is estimated close to AUD $35 Million per year. Contamination of packaged foods due to micro-organisms entering through air leaks can cause serious public health issues and cost companies large sums of money due to product recalls, compensation claims and loss of market share. The main source of contamination is leaks in packaging which allow air, moisture and micro-organisms to enter the package. Flexible plastic packages are widely used, and are the least expensive form of retaining the quality of the product. These packets can be used to seal, and therefore maximise, the shelf life of both dry and moist products. The seals of food packages need to be airtight so that the food content is not contaminated due to contact with microorganisms that enter as a result of air leakage. Airtight seals also extend the shelf life of packaged foods, and manufacturers attempt to prevent food products with leaky seals being sold to consumers. There are many current NDT (non-destructive testing) methods of testing the seal of flexible packages best suited to random sampling, and for laboratory purposes. The three most commonly used methods are vacuum/pressure decay, bubble test, and helium leak detection. Although these methods can detect very fine leaks, they are limited by their high processing time and are not viable in a production line. Two nondestructive in-line packaging inspection machines are currently available and are discussed in the literature review. The detailed design and development of the High-Speed Sensing and Detection System (HSDS) is the fundamental requirement of this project and the future prototype and production unit. Successful laboratory testing was completed and a methodical design procedure was needed for a successful concept. The Mechanical tests confirmed the vacuum hypothesis and seal integrity with good consistent results. Electrically, the testing also provided solid results to enable the researcher to move the project forward with a certain amount of confidence. The laboratory design testing allowed the researcher to confirm theoretical assumptions before moving into the detailed design phase. Discussion on the development of the alternative concepts in both mechanical and electrical disciplines enables the researcher to make an informed decision. Each major mechanical and electrical component is detailed through the research and design process. The design procedure methodically works through the various major functions both from a mechanical and electrical perspective. It opens up alternative ideas for the major components that although are sometimes not practical in this application, show that the researcher has exhausted all engineering and functionality thoughts. Further concepts were then designed and developed for the entire HSDS unit based on previous practice and theory. In the future, it would be envisaged that both the Prototype and Production version of the HSDS would utilise standard industry available components, manufactured and distributed locally. Future research and testing of the prototype unit could result in a successful trial unit being incorporated in a working food processing production environment. Recommendations and future works are discussed, along with options in other food processing and packaging disciplines, and other areas in the non-food processing industry.

Impact of the Corporate Law Economic Reform Program Act 1999 on initial public offering prospectus earnings forecasts

Commencing 13 March 2000, the Corporate Law Economic Reform Program Act 1999 (Cth) introduced changes to the regulation of corporate fundraising in Australia. In particular, it effected a reduction in the litigation risk associated with initial public offering prospectus disclosure.We find that the change is associated with a reduction in forecast frequency and an increase in forecast value relevance, but not with forecast error or bias. These results confirm previous findings that changes in litigation risk affect the level but not the quality of disclosure. They also suggest that the reforms’ objectives of reducing fundraising costs while improving investor protection, have been achieved.

The role of organisational culture, trust and mechanisms in inter-project knowledge sharing

Knowledge has been recognised as a powerful yet intangible asset, which is difficult to manage. This is especially true in a project environment where there is the potential to repeat mistakes, rather than learn from previous experiences. The literature in the project management field has recognised the importance of knowledge sharing (KS) within and between projects. However, studies in that field focus primarily on KS mechanisms including lessons learned (LL) and post project reviews as the source of knowledge for future projects, and only some preliminary research has been carried out on the aspects of project management offices (PMOs) and organisational culture (OC) in KS. This study undertook to investigate KS behaviours in an inter-project context, with a particular emphasis on the role of trust, OC and a range of knowledge sharing mechanisms (KSM) in achieving successful inter-project knowledge sharing (I-PKS). An extensive literature search resulted in the development of an I-PKS Framework, which defined the scope of the research and shaped its initial design. The literature review indicated that existing research relating to the three factors of OC, trust and KSM remains inadequate in its ability to fully explain the role of these contextual factors. In particular, the literature review identified these areas of interest: (1) the conflicting answers to some of the major questions related to KSM, (2) the limited empirical research on the role of different trust dimensions, (3) limited empirical evidence of the role of OC in KS, and (4) the insufficient research on KS in an inter-project context. The resulting Framework comprised the three main factors including: OC, trust and KSM, demonstrating a more integrated view of KS in the inter-project context. Accordingly, the aim of this research was to examine the relationships between these three factors and KS by investigating behaviours related to KS from the project managers‘ (PMs‘) perspective. In order to achieve the aim, this research sought to answer the following research questions: 1. How does organisational culture influence inter-project knowledge sharing? 2. How does the existence of three forms of trust — (i) ability, (ii) benevolence and (iii) integrity — influence inter-project knowledge sharing? 3. How can different knowledge sharing mechanisms (relational, project management tools and process, and technology) improve inter-project knowledge sharing behaviours? 4. How do the relationships between these three factors of organisational culture, trust and knowledge sharing mechanisms improve inter-project knowledge sharing? a. What are the relationships between the factors? b. What is the best fit for given cases to ensure more effective inter-project knowledge sharing? Using multiple case studies, this research was designed to build propositions emerging from cross-case data analysis. The four cases were chosen on the basis of theoretical sampling. All cases were large project-based organisations (PBOs), with a strong matrix-type structure, as per the typology proposed by the Project Management Body of Knowledge (PMBoK) (2008). Data were collected from project management departments of the respective organisations. A range of analytical techniques were used to deal with the data including pattern matching logic and explanation building analysis, complemented by the use of NVivo for data coding and management. Propositions generated at the end of the analyses were further compared with the extant literature, and practical implications based on the data and literature were suggested in order to improve I-PKS. Findings from this research conclude that OC, trust, and KSM contribute to inter-project knowledge sharing, and suggest the existence of relationships between these factors. In view of that, this research identified the relationships between different trust dimensions, suggesting that integrity trust reinforces the relationship between ability trust and knowledge sharing. Furthermore, this research demonstrated that characteristics of culture and trust interact to reinforce preferences for mechanisms of knowledge sharing. This means that cultures that facilitate characteristics of Clan type are more likely to result in trusting relationships, hence are more likely to use organic sources of knowledge for both tacit and explicit knowledge exchange. In contrast, cultures that are empirically driven, based on control, efficiency, and measures (characteristics of Hierarchy and Market types) display tendency to develop trust primarily in ability of non-organic sources, and therefore use these sources to share mainly explicit knowledge. This thesis contributes to the project management literature by providing a more integrative view of I-PKS, bringing the factors of OC, trust and KSM into the picture. A further contribution is related to the use of collaborative tools as a substitute for static LL databases and as a facilitator for tacit KS between geographically dispersed projects. This research adds to the literature on OC by providing rich empirical evidence of the relationships between OC and the willingness to share knowledge, and by providing empirical evidence that OC has an effect on trust; in doing so this research extends the theoretical propositions outlined by previous research. This study also extends the research on trust by identifying the relationships between different trust dimensions, suggesting that integrity trust reinforces the relationship between ability trust and KS. Finally, this research provides some directions for future studies.

Were regulatory changes in reporting "abnormal items" justified? : evidence of intra-period classificatory earnings management practices in Australia

Purpose Managers generally have discretion in determining how components of earnings are presented in financial statements in distinguishing between ‘normal’ earnings and items classified as unusual, special, significant, exceptional or abnormal. Prior research has found that such intra-period classificatory choice is used as a form of earnings management. Prior to 2001, Australian accounting standards mandated that unusually large items of revenue and expense be classified as ‘abnormal items’ for financial reporting, but this classification was removed from accounting standards from 2001. This move by the regulators was partly in response to concerns that the abnormal classification was being used opportunistically to manage reported pre-abnormal earnings. This study extends the earnings management literature by examining the reporting of abnormal items for evidence of intra-period classificatory earnings management in the unique Australian setting. Design/methodology/approach This study investigates associations between reporting of abnormal items and incentives in the form of analyst following and the earnings benchmarks of analysts’ forecasts, earnings levels, and earnings changes, for a sample of Australian top-500 firms for the seven-year period from 1994 to 2000. Findings The findings suggest there are systematic differences between firms reporting abnormal items and those with no abnormal items. Results show evidence that, on average, firms shifted expense items from pre-abnormal earnings to bottom line net income through reclassification as abnormal losses. Originality/value These findings suggest that the standard setters were justified in removing the ‘abnormal’ classification from the accounting standard. However, it cannot be assumed that all firms acted opportunistically in the classification of items as abnormal. With the removal of the standardised classification of items outside normal operations as ‘abnormal’, firms lost the opportunity to use such disclosures as a signalling device, with the consequential effect of limiting the scope of effectively communicating information about the nature of items presented in financial reports.