Interaction of single-walled carbon nanotubes with poly(propyl ether imine) dendrimers

We study the complexation of nontoxic, native poly(propyl ether imine) dendrimers with single-walled carbon nanotubes (SWNTs). The interaction was monitored by measuring the quenching of inherent fluorescence of the dendrimer. The dendrimer-nanotube binding also resulted in the increased electrical resistance of the hole doped SWNT, due to charge-transfer interaction between dendrimer and nanotube. This charge-transfer interaction was further corroborated by observing a shift in frequency of the tangential Raman modes of SWNT. We also report the effect of acidic and neutral pH conditions on the binding affinities. Experimental studies were supplemented by all atom molecular dynamics simulations to provide a microscopic picture of the dendrimer-nanotube complex. The complexation was achieved through charge transfer and hydrophobic interactions, aided by multitude of oxygen, nitrogen, and n-propyl moieties of the dendrimer. (C) 2011 American Institute of Physics. doi:10.1063/1.3561308]

Structural and transport properties of high energy ion irradiated YBCO

The effects of 100 MeV Oxygen and 200 MeV Silver ions on the structural and transport properties of YBCO thin films are reported. Both normal state and superconducting properties were studied on Laser ablated and high pressure oxygen sputtered films. Precise electrical resistance and critical current measurements near T-c were made and the data obtained were analysed in the light of existing models of para-coherence near T-c and the other aspects of radiation damage arising from microstructural studies such as atomic force microscopy (AFM). There was evidence of sputtering by high energy ions from AFM measurement. (C) 1998 Elsevier Science Ltd. All rights reserved.

Mapping of local electronic properties in nanostructured CMR thin films by Scanning Tunneling Microscopy (STM) and Local Conductance Map (LCMAP)

We have investigated the local electronic properties and the spatially resolved magnetoresistance of a nanostructured film of a colossal magnetoresistive (CMR) material by local conductance mapping (LCMAP) using a variable temperature Scanning Tunneling Microscope (STM) operating in a magnetic field. The nanostructured thin films (thickness ≈500nm) of the CMR material La0.67Sr0.33MnO3 (LSMO) on quartz substrates were prepared using chemical solution deposition (CSD) process. The CSD grown films were imaged by both STM and atomic force microscopy (AFM). Due to the presence of a large number of grain boundaries (GB's), these films show low field magnetoresistance (LFMR) which increases at lower temperatures. The measurement of spatially resolved electronic properties reveal the extent of variation of the density of states (DOS) at and close to the Fermi level (EF) across the grain boundaries and its role in the electrical resistance of the GB. Measurement of the local conductance maps (LCMAP) as a function of magnetic field as well as temperature reveals that the LFMR occurs at the GB. While it was known that LFMR in CMR films originates from the GB, this is the first investigation that maps the local electronic properties at a GB in a magnetic field and traces the origin of LFMR at the GB.

Domain-wall creep driven by spin torque in nanoscale ferromagnetic cylinders

We have explored the mechanism of spin-torque-driven domain-wall (DW) depinning in cylindrical nanowires of nickel using noise in electrical resistance. We find that the spectral slope of noise is a sensitive probe to the DW kinetics that reveals a creeplike behavior of the DWs at the depinning threshold, and diffusive DW motion at higher spin-torque drive. Different regimes of DW kinetics were characterized by universal kinetic exponents.

Insulating State and Breakdown of Fermi Liquid Description in Molecular-Scale Single-Crystalline Wires of Gold

Electrical transport measurements on ultrathin single-crystalline Au nanowires, synthesized via a wet chemical route, show an unexpected insulating behavior. The linear response electrical resistance exhibits a power-law dependence on temperature. In addition, the variation of current over a wide range of temperature and voltage obeys a universal scaling relation that provides compelling evidence for a non-Fermi liquid behavior. Our results demonstrate that the quantum ground state In ultrathin nanowires of simple metallic systems can be radically different from their bulk counterparts and can be described In terms of a Tomonaga-Luttinger liquid (TLL), in the presence of remarkably strong electron-electron interactions.

Synthesis, Characterization and Properties of Single-Walled Carbon Nanohorns

Single-walled nanohorns (SWNHs) have been prepared by sub-merged arc discharge of graphite electrodes in liquid nitrogen. The samples were examined by scanning electron microscopy, transmission electron microscopy and Raman spectroscopy. Nitrogen and boron doped SWNHs have been prepared by the sub-merged arc discharge method using melamine and elemental boron as precursors. Intensification of Raman D-band and stiffening of G-band has been observed in the doped samples. The electrical resistance of the SWNHs varies in opposite directions with nitrogen and boron doping. Functionalization of SWNHs through amidation has been carried out for solubilizing them in non-polar solvents. Water-soluble SWNHs have been produced by acid treatment and non-covalent functionalization with a coronene salt. SWNHs have been decorated with nanoparticles of Au, Ag and Pt. Interaction of electron donor (tetrathiafulvalene, TTF) and acceptor molecules (tetracyanoethylene, TCNE) with SWNHs has been investigated by Raman spectroscopy. Progressive softening and stiffening of Raman G-band has been observed respectively with increase in the concentration of TTF and TCNE.

Electrothermally tunable MEMS filters

MEMS resonators have potential application in the area of frequency selective devices (e.g., gyroscopes, mass sensors, etc.). In this paper, design of electro thermally tunable resonators is presented. SOIMUMPs process is used to fabricate resonators with springs (beams) and a central mass. When voltage is applied, due to joule heating, temperature of the conducting beams goes up. This results in increase of electrical resistance due to mobility degradation. Due to increase in the temperature, springs start softening and therefore the fundamental frequency decreases. So for a given structure, one can modify the original fundamental frequency by changing the applied voltage. Coupled thermal effects result in non-uniform heating. It is observed from measurements and simulations that some parts of the beam become very hot and therefore soften more. Consequently, at higher voltages, the structure (equivalent to a single resonator) behaves like coupled resonators and exhibits peak splitting. In this mode, the given resonator can be used as a band rejection filter. This process is reversible and repeatable. For the designed structure, it is experimentally shown that by varying the voltage from 1 to 16V, the resonant frequency could be changed by 28%.

Modulation of Electronic and Self-Assembly Properties of a Donor-Acceptor-Donor-Based Molecular Materials via Atomistic Approach

The performance of molecular materials in optoelectronic devices critically depends upon their electronic properties and solid-state structure. In this report, we have synthesized sulfur and selenium based (T4BT and T4BSe) donor-acceptor-donor (D-A-D) organic derivatives in order to understand the structure-property correlation in organic semiconductors by selectively tuning the chalcogen atom. The photophysical properties exhibit a significant alteration upon varying a single atom in the molecular structure. A joint theoretical and experimental investigation suggests that replacing sulfur with selenium significantly reduces the band gap and molar absorption coefficient because of lower electronegativity and ionization potential of selenium. Single-crystal X-ray diffraction analysis showed differences in their solid-state packing and intermolecular interactions. Subsequently, difference in the solid-state packing results variation in self-assembly. Micorstructural changes within these materials are correlated to their electrical resistance variation, investigated by conducting probe atomic force microscopy (CP-AFM) measurements. These results provide useful guidelines to understand the fundamental properties of D-A-D materials prepared by atomistic modulation.

Structure and properties of an amorphous ferromagnetic alloy

The structure and the electrical and magnetic properties of an amorphous alloy containing approximately 80 at .% iron, 13 at.% phos phorus and 7 at.% carbon (Fe_(80)Fe_(13)C_7) obtained by rapid quenching from the liquid state have been studied. Transmission electron diffraction data confirm the amorphous nature of this alloy. An analysis of the radial distribution function obtained from X-ray diffraction data indicates that the number of nearest neighbors is approximately seven, at a distance of 2.6A. The structure of the alloy can be related to that of silicate glasses and is based on a random arrangement of trigonal prisms of Fe_2P and Fe_3C types in which the iron atoms have an average ligancy of seven. Electrical resistance measurements show that the alloys are metallic. A minimum in the electrical resistivity vs. temperature curve is observed between 10° K to 50° K depending on the specimen, and the temperature at which the minimum occurs is related to the degree of local ordering. The Fe-P-C amorphous alloys are ferromagnetic. The Curie temperature measured by the induction method and by Mossbauer spectroscopy is 315° C. The field dependence of the magneto-resistance at temperatures from liquid helium to room temperature is similar to that found in crystalline iron. The ordinary Hall coefficient is approximately 10^(-11) volt-cm/amp-G. The spontaneous Hall coefficient is about 0.6 x 10^(-9) volt-cm/amp-G and is practically independent of temperature from liquid helium temperature up to 300° c.

Lattice anomalies and magnetic states in Fe_5Si_3-Mn_5Si_3 alloys

The lattice anomalies and magnetic states in the (Fe_100-xMn_x)₅Si₃ alloys have been investigated. Contrary to what was previously reported, results of x-ray diffraction show a second phase (α') present in Fe-rich alloys and therefore strictly speaking a complete solid solution does not exist. Mössbauer spectra, measured as a function of composition and temperature, indicate the presence of two inequivalent sites, namely 6(g) site (designated as site I) and 4(d) (site II). A two-site model (TSM) has been introduced to interpret the experimental findings. The compositional variation of lattice parameters a and c, determined from the x-ray analysis, exhibits anomalies at x = 22.5 and x = 50, respectively. The former can be attributed to the effect of a ferromagnetic transition; while the latter is due to the effect of preferential substitution between Fe and Mn atoms according to TSM.

The reduced magnetization of these alloys deduced from magnetic hyperfine splittings has been correlated with the magnetic transition temperatures in terms of the molecular field theory. It has been found from both the Mössbauer effect and magnetization measurements that for composition 0 ≤ x ˂ 50 both sites I and II are ferromagnetic at liquid-nitrogen temperature and possess moments parallel to each other. In the composition range 50 ˂ x ≤ 100 , the site II is antiferromagnetic whereas site I is paramagnetic even at a temperature below the bulk Néel temperatures. In the vicinity of x = 50 however, site II is in a state of transition between ferromagnetism and antiferromagnetism. The present study also suggests that only Mn in site II are responsible for the antiferromagnetism in Mn₅Si₃ contrary to a previous report.

Electrical resistance has also been measured as a function of temperature and composition. The resistive anomalies observed in the Mn-rich alloys are believed to result from the effect of the antiferromagnetic Brillouin zone on the mobility of conduction electrons.

Verificação experimental da largura colaborante em mesas de lajes nervuradas.

Este trabalho apresenta um estudo experimental para determinação da largura colaborante em mesas de lajes nervuradas de concreto armado. Esta largura é definida comumente utilizando-se as recomendações contidas nas diversas normas e procedimentos já consagrados de estruturas de concreto armado. Visando a determinação da largura da mesa que efetivamente contribui na capacidade resistente da seção de lajes nervuradas, foram instrumentados e ensaiados modelos que buscaram reproduzir faixas de nervuras e painéis de laje. As faixas possuíam dimensões reais de duas nervuras principais, enquanto as lajes reproduziam painéis em escala reduzida (1:2). Em parte dos modelos, foram inseridos extensômetros de resistência elétrica nas armaduras e no concreto, além de transdutores para verificação das flechas. Foram calculadas as larguras a partir das curvas de tensões e flechas verificadas experimentalmente. Verificou-se, também, a influência da presença de tubulação embutida ao longo da mesa das faixas de laje.

Caracterização microestrutural e análise de tensões residuais pelo método do furo cego em tubo de seção quadrada com costura.

Tensões residuais são uma das principais causas de falhas em componentes mecânicos submetidos a processos de fabricação. O objetivo do trabalho foi medir as tensões residuais presentes em um tubo quadrado soldado por resistência elétrica de alta frequência e caracterizar microestruturalmente o seu material. Para a caracterização, foram utilizadas técnicas de microscopia óptica (MO), microscopia eletrônica de varredura (MEV) e análise química quantitativa. Para a medição das tensões residuais, foi utilizado o método do furo cego, baseado na norma ASTM E837-08, onde rosetas (strain-gages) são coladas à peça para medir as deformações geradas devido à usinagem de um pequeno furo no local de medição. As deformações foram associadas às tensões residuais através de equações baseadas na Lei de Hooke. A caracterização revelou uma microestrutura composta basicamente de ferrita e perlita, típica de aços com baixo teor de carbono, corroborando com a especificação fornecida pelo fabricante. As tensões residuais encontradas foram trativas e mostraram-se elevadas, com alguns valores acima do limite de escoamento do material.

Influência da superexpressão da claudina-3 na radiorresposta de células de câncer de cólon

O câncer colorretal (CCR) é o terceiro tipo de câncer mais incidente no mundo para o sexo masculino, o segundo para o sexo feminino e a radioterapia é um dos tratamentos de primeira linha no combate a este tipo de câncer. Durante a progressão do CCR as células sofrem alterações morfogenéticas, sendo a desorganização do complexo juncional apical (CJA) um dos eventos iniciais desse processo. As junções oclusivas (JTs) são um dos principais componentes da CJA e desempenham papel importante no controle do fluxo paracelular, na determinação da polaridade celular e na transdução de sinais relacionados com a progressão tumoral. As claudinas são proteínas transmembrana, constituintes das JTs e cumprem um importante papel no controle desses eventos. Alterações na expressão das claudinas são observadas em tumores de diferentes órgãos e têm sido relacionadas com a progressão tumoral. No entanto os mecanismos que regulam essas alterações e sua consequência na progressão do CCR são poucos conhecidos. Desta forma, o presente estudo teve como objetivo avaliar a influência da superexpressão da claudina-3 na radiorresposta de células CCR. Nossos resultados mostraram que a superexpressão de claudina-3 minimiza alterações morfológicas causadas pela radiação, causa diminuição da resistência elétrica transepitelial e não tem efeito na permeabilidade a macromoléculas após a irradiação. Além disso, observamos que a superexpressão de claudina-3 aumenta o potencial proliferativo das células e que esta característica torna as células mais sensíveis a radiação. Porém quando avaliamos eventos celulares relacionados a progressão tumoral observamos que apesar da radiação diminuir a capacidade migratória das progênies, as células que superexpressam claudina-3 apresentam migração mais elevada. Além disso, verificamos que a superexpressão de claudina-3 diminui a invasão e a capacidade de formação de colônias frente ao tratamento com a radiação. Em seguida fomos avaliar o efeito da inibição das vias de proliferação (MEK/ERK) e sobrevivência (PI3K-Akt) na resposta das células que superexpressam claudina-3 frente a radiação. Observamos que a inibição de MEK é capaz de sensibilizar as células que superexpressam claudina-3 à radiação no ensaio de proliferação celular, no entanto a inibição de MEK e PI3K antes da exposição à radiação é capaz aumentar a migração e a capacidade de formação de colônias de células que superexpressam claudina-3 contribuindo para o aumento do potencial maligno. Em conjunto nossos resultados mostram que a superexpressão de claudina-3 contribui para um fenótipo mais maligno, no entanto frente ao tratamento com a radiação é capaz de sensibilizar as células.

Instrument for the measurement of the fore and aft tilt of otterboards

A portable self-contained instrument has been designed and developed for the measurement of the Fore and Aft tilt of otter boards within the range —22° to + 22° with an accuracy of ± 1°. An underwater transducer fitted on the otter board converts its tilt into corresponding electrical resistance which is measured in an ohmmeter on board, both being connected by electric cable.

Effect of electric stimulation on heart beat and body muscle in fish

The effect of AC and DC electric stimulations on the heart-rate and the entire body of Heteropneustis fossillis, Tilapia mossambica and Macrobrachium rosenbergii were studied and presented in kymograph tracings. The reaction of spinal cord in Puntius ticto, Heteropneustis fossilis and Tilapia mossambica to D. C. field was observed to find out its role in electric shocks. A test-check of the electrical resistance of a few species was also conducted. The effect of D. C. and A.C. on the body muscle was found to be the same as that in the case of frog. Different degrees of cardiac slowing were observed in AC and DC. Unbalanced galvanotropic movements were also noticed in spinal fishes.