Automatic tread gaging machine. Technical report.

Mode of access: Internet.

Mode control in multimode optical fibre and its applications

This thesis describes an investigation into methods for controlling the mode distribution in multimode optical fibres. The major contributions presented in this thesis are summarised below. Emerging standards for Gigabit Ethernet transmission over multimode optical fibre have led to a resurgence of interest in the precise control, and specification, of modal launch conditions. In particular, commercial LED and OTDR test equipment does not, in general, comply with these standards. There is therefore a need for mode control devices, which can ensure compliance with the standards. A novel device consisting of a point-load mode-scrambler in tandem with a mode-filter is described in this thesis. The device, which has been patented, may be tuned to achieve a wide range of mode distributions and has been implemented in a ruggedised package for field use. Various other techniques for mode control have been described in this work, including the use of Long Period Gratings and air-gap mode-filters. Some of the methods have been applied to other applications, such as speckle suppression and in sensor technology. A novel, self-referencing, sensor comprising two modal groups in the Mode Power Distribution has been designed and tested. The feasibility of a two-channel Mode Group Diversity Multiplexed system has been demonstrated over 985m. A test apparatus for measuring mode distribution has been designed and constructed. The apparatus consists of a purpose-built video microscope, and comprehensive control and analysis software written in Visual Basic. The system may be fitted with a Silicon camera or an InGaAs camera, for measurement in the 850nm and 130nm transmission windows respectively. A limitation of the measurement method, when applied to well-filled fibres, has been identified and an improvement to the method has been proposed, based on modelled Laguerre Gauss field solutions.

Physical oceanography during SONNE cruise SO248 (BacGeoPac)

The data presented here were collected during the cruise SO248 (Project BacGeoPac) with the RV Sonne from Auckland, New Zealand to Dutch Harbor, Alaska/USA. The cruise lasted from May 1, 2016 to June 3, 2016 and 19 vertical CTD-hauls were conducted. The CTD system used during this cruise was a Sea-Bird Electronics Inc. SBE 911plus probe (SN 09-1266). The CTD was attached to a SBE 32 Carousel Water Sampler (SN 32-1119) containing 24 20-liter Ocean Test Equipment Inc. bottles. The system was equipped with double temperature (SBE 3) and conductivity sensors (SBE 4), a pressure sensor (Digiquartz) an oxygen (Aanderaa Optode 4831F) and, an altimeter (Bentos) and a chlorophyll fluorometer combined with a turbidity sensor (FluoroWetlabECO _AFL FL). The sensors were pre-calibrated by the manufacturers. The data were recorded with the Seasave V 7.23.2 software and processed using the SeaBird SBE Data Processing and the ManageCTD-software. The data were processed in the following way: Data obtained during adaptation of the CTD to ambient water conditions were removed manually. The "wildedit", "loopedit", "despike", "binavg" routines were applied. The data were also visually checked and a double sensor check was conducted. The accuracy of the double sensors derived from 56 data sets were: Temperature T = 0.0007 °C; Conductivity: C = 0,0071 mS/cm; Salinity S = 0.0081 psu. The salinity data (S by unsing pss78) were converted to absolute Salinity (SA) by using the TEOS 10 toolbox. The ship position data were derived from the shipboard GPS-system linked to the CTD data. The time zone is given in UTC. The oxygen CTD data were validated by additional measurements of 98 water samples using the Winkler titration method.

Análise de desempenho de um refrigerador de pequeno porte com drop in de refrigerantes hidrocarbonetos

From what was stated in the Montreal Protocol, the researchers and refrigeration industry seek substitutes for synthetic refrigerants -chlorofluorocarbons (CFCs) and HCFCs (HCFC) - that contribute to the depletion of the ozone layer. The phase-out of these substances was started using as one of the replacement alternatives the synthetic fluids based on hydro fluorocarbons (HFCs) that have zero potential depletion of the ozone layer. However, contribute to the process of global warming. HFC refrigerants are greenhouse gases and are part of the group of gases whose emissions must be reduced as the Kyoto Protocol says. The hydrocarbons (HC's), for not contribute to the depletion of the ozone layer, because they have very low global warming potential, and are found abundantly in nature, has been presented as an alternative, and therefore, are being used in new home refrigeration equipment in several countries. In Brazil, due to incipient production of domestic refrigerators using HC's, the transition refrigerants remain on the scene for some years. This dissertation deals with an experimental evaluation of the conduct of a drinking fountain designed to work with HFC (R-134a), operating with a mixture of HC's or isobutane (R-600a) without any modification to the system or the lubricating oil. In the refrigeration laboratory of Federal University of Rio Grande do Norte were installed, in a drinking fountain, temperature and pressure sensors at strategic points in the refrigeration cycle, connected to an acquisition system of computerized data, to enable the mapping and thermodynamics analysis of the device operating with R-134a or with a mixture of HC's or with R-600a. The refrigerator-test operating with the natural fluids (mixture of HC's or R-600a) had a coefficient of performance (COP) lower than the R-134a

Operator's manual including basic issue items list : test set, generator, and voltage regulator, automotive (Allen Electric and Equipment Co. model 30-82) (4910-270-3780).

"April 1965."

Operator, organizational, direct support, and general support maintenance manual (including repair parts and special tools list and depot maintenance repair parts and special tools) : test set, generator and voltage regulator, automotive, 12-and 24-volt systems (Allen Electric and Equipment Company model no. 30-92) (4910-092-9136).

"15 October 1971."

Operator, organizational, DS and GS maintenance manual for test set, guided missile system, AN/TSM-84 and electrical equipment shelter, S-250/G (modified) : (Lance guided missile system).

Includes index.

Organizational, direct support, and general support maintenance repair parts and special tools list for test stand, automotive generator, alternator, starter, and associated equipment, model GASR-500 : part number 7458-2, 7458-4, NSN 4910-01-041-8161, 4910-00-767-0218.

"May 1987."

Direct support and general support maintenance manual : test stand, automotive generator, alternator, starter, and associated equipment, model GASR-500 : part number 7458-2 ....

"June 1981."

Direct support and general support maintenance manual : receiver radio frequency noise measurement equipment including test set, radio frequency noise TS-3376/G (NSN 6625-00-237-2406), monitor, noise temperature ID-1915/G (NSN 5895-00-241-9367) for satellite communication terminal AN/FSC-78(V).

"June 1978."

General support maintenance repair parts and special tools list for test station, electronic equipment AN/USM-410(V)2 (NSN 6625-01-069-4223).

"18 October 1985."

Organizational and direct support maintenance manual for electronic equipment test facility TADS/PNVS augmentation equipment, 13082808-39, 13231600, 13231650, and 13231800.

"1 February 1986."

Comparison of ultrafine particle release from hardcopy devices in emission test chambers and office rooms

The release of ultrafine particles (UFP) from laser printers and office equipment was analyzed using a particle counter (FMPS; Fast Mobility Particle Sizer) with a high time resolution, as well as the appropriate mathematical models. Measurements were carried out in a 1 m³ chamber, a 24 m³ chamber and an office. The time-dependent emission rates were calculated for these environments using a deconvolution model, after which the total amount of emitted particles was calculated. The total amounts of released particles were found to be independent of the environmental parameters and therefore, in principle, they were appropriate for the comparison of different printers. On the basis of the time-dependent emission rates, “initial burst” emitters and constant emitters could also be distinguished. In the case of an “initial burst” emitter, the comparison to other devices is generally affected by strong variations between individual measurements. When conducting exposure assessments for UFP in an office, the spatial distribution of the particles also had to be considered. In this work, the spatial distribution was predicted on a case by case basis, using CFD simulation.