Evaluation of serological tests for the diagnosis of Neospora caninum infection in dogs: Optimization of cut off titers and inhibition studies of cross-reactivity with Toxoplasma gondii

Diagnosis of Neospora caninum infection in dogs is based on serological assays such as the indirect fluorescent antibody test (IFAT) and enzyme-linked immunosorbent assays (ELISA). This study evaluated two serological tests (IFAT and ELISA) for the detection of IgG antibodies to N. caninum in 300 serum samples of dogs through the optimization of cut off titers by using the two-graph receiveroperating characteristic (TG-ROC) curve. In addition, the identification of major cross-reactive antigens with Toxoplasma gondii was investigated by inhibition ELISA and immunoblotting (IB) assays. IFAT and ELISA results showed 74% agreement, with a good negative concordance (P-neg=0.83), but a poor positive concordance (P-pos=0.42). The great majority (86%) of sera with positive concordant results (IFAT+/ELISA+) recognized at least two out of three N. caninum immunodominant antigens, particularly the 29-32 and 35-37 kDa bands. Optimization of cut off titers in IFAT and ELISA was performed considering the reactivity to at least two out of three N. caninum immunodominant antigens as infection markers, obtaining a titer of 50 for IFAT and 200 for ELISA. Seropositivity to N. caninuin was significantly associated with T gondii-seropositive samples, particularly in ELISA (55.4%). Inhibition ELISA curves for N. caninum showed a partial heterologous inhibition, indicating some degree of cross-reactivity between N. caninum and T gondii antigens. Inhibition IB assays showed a moderate heterologous inhibition for N. caninum antigens above 45-50 kDa. These results indicate that ELISA should be used critically when crude tachyzoite antigen preparations are employed, due to possible cross-reactivity with other related parasites as T gondii. Also, the cut off dilution of 1:50 in IFAT showed to be the most appropriated for N. caninum serology in dogs. Therefore, we suggest that N. caninum immunodominant antigens, specially the 17 and 29-32 kDa proteins, should be selected markers in serological assays for canine neosporosis. (c) 2006 Elsevier B.V. All rights reserved.

Effect of storage of cuttings on the rooting of different cultivars of cut chrysanthemums (Dendranthema grandiflora Tzvelev) for two different seasons

Chrysanthemums are commercially propagated through cuttings. Pre-rooting storage of cuttings in the dark is a common practice among growers and companies that work and trade with chrysanthemum cuttings. Therefore, the maximum storage period for cuttings and differences in tolerance among cultivars has been investigated. Adventitious roots of cuttings can originate in almost any tissue, including the epidermis, stem cortex and pericycle, ray parenchyma, immature xylem and phloem cells, and pith. The aims of this work were to determine the effect of time of cold storage of cuttings (0, 1, 2, 3, 4, 5 and 6 weeks) on the rooting of four cut chrysanthemum cultivars (Super White, Sheena, Dark Orange Reagan and Town Talk) for two seasons of the year (summer and winter), and also to determine the origin of root formation in chrysanthemum cuttings. The study was carried out as a randomized complete block design with 5 replications for each storage treatment. Each plot was comprised of three cuttings that were examined 14 days after the cutting procedure. During the winter, the roots were studied by scanning electron microscopy (SEM) at the Electron Microscope Laboratory. The following conclusions were made: in winter, cold storage affected the rooting of cuttings, mainly after two weeks of storage for all cultivars. The rooting percentage was lower in the winter and the cuttings could be preserved for a shorter period. The source and growth of roots in chrysanthemum cuttings was found to be endogenous. After three days, callus formed in the pericycle and the first emergence of adventitious roots occurred by the fourth day of rooting. During the summer, cold storage could be up to 4 weeks without any problems.

Water relations of cut inflorescences of Alpinia purpurata treated with seven pulsing solutions

Alpinia purpurata (Vieill) K. Schum, common name red ginger belongs to Zingiberaceae family, and is a perennial, with nice inflorescences composed of layers of bracts arranged in spirals. The utilization of keeping-quality solutions seeks to prolong vase-life and to maintain the quality of cut flowers. This research was performed to evaluate the effect of seven pulsing solutions (during 24 hours) on water relations, quality (turgor, browning and curvature) and the longevity of cut red ginger. The experiment followed complete randomized design, in factorial arrangement. The following treatments were studied: 1) distilled water (control), 2) sucrose 2% + 8-hidroxyquinoline citrate 200 ppm, 3) sucrose 2%, 4) sucrose 2% + citric acid, 5) benzyladenine 10 μM, 6) benzyladenine 10 μmol + sucrose 2%, 7) quaternary ammonia 0,5 mL/L. There was no significant (P>0.05) reduction of the relative water content (RWC) of the inflorescence bracts, among solutions, in the first period (7 days) and in the second period (14 days) and, between the two periods for all treatments. Significant differences among RWC of some treatments were recorded after 16 days of vase life. The utilization of benzyladenine, benzyladenine plus sucrose and sucrose plus citric acid, in the pulsing solution, allowed to keep the flowers quality for longer periods than the other treatments.

Cutting performance of diamond coated Si3N4 tool during turning

Silicon nitride cutting tools have been used successfully for machining hard materials, like: cast irons, nickel based alloys, etc. However these cutting tools with diamond coating present little information on dry turning operations of gray cast iron. In the present work, Si3N4 square inserts was developed, characterized and subsequently coated with diamond for dry machining operations on gray cast iron. All experiments were conducted with replica. It was used a 1500, 3000, 4500 m cutting length, feed rate of 0.33 mm/rev and keeping the depth of cut constant and equal to 1 mm. The results show that wear in the tool tips of the Si3N4 inserts, in all cutting conditions, was caused by both mechanical and chemical processes. To understand the tool wear mechanisms, a morphological analysis of the inserts, after experiments, has been performed by SEM and optical microscopy. Diamond coated PVD inserts showed to be capable to reach large cutting lengths when machining gray cast iron. © (2010) Trans Tech Publications.

Quality of cut and basecutter blade configuration for the mechanized harvest of green sugarcane

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Dynamics of soil exploration by fine roots down to a depth of 10 m throughout the entire rotation in Eucalyptus grandis plantations

Although highly weathered soils cover considerable areas in tropical regions, little is known about exploration by roots in deep soil layers. Intensively managed Eucalyptus plantations are simple forest ecosystems that can provide an insight into the belowground growth strategy of fast-growing tropical trees. Fast exploration of deep soil layers by eucalypt fine roots may contribute to achieving a gross primary production that is among the highest in the world for forests. Soil exploration by fine roots down to a depth of 10 m was studied throughout the complete cycle in Eucalyptus grandis plantations managed in short rotation. Intersects of fine roots, less than 1 mm in diameter, and medium-sized roots, 1-3 mm in diameter, were counted on trench walls in a chronosequence of 1-, 2-, 3.5-, and 6-year-old plantations on a sandy soil, as well as in an adjacent 6-year-old stand growing in a clayey soil. Two soil profiles were studied down to a depth of 10 m in each stand (down to 6 m at ages 1 and 2 years) and 4 soil profiles down to 1.5-3.0 m deep. The root intersects were counted on 224 m(2) of trench walls in 15 pits. Monitoring the soil water content showed that, after clear cutting, almost all the available water stored down to a depth of 7 m was taken up by tree roots within 1.1 year of planting. The soil space was explored intensively by fine roots down to a depth of 3 m from 1 year after planting, with an increase in anisotropy in the upper layers throughout the rotation. About 60% of fine root intersects were found at a depth of more than 1 m, irrespective of stand age. The root distribution was isotropic in deep soil layers and kriged maps showed fine root clumping. A considerable volume of soil was explored by fine roots in eucalypt plantations on deep tropical soils, which might prevent water and nutrient losses by deep drainage after canopy closure and contribute to maximizing resource uses.

Application of acoustoelasticity to measure the stress generated by milling in ASTM A36 steel plates

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Accuracy of radiographic examination in determining the depth of approximal carious lesions in primary molars

The purpose of this study was to evaluate the accuracy of the depth of carious lesions on bitewing radiographs. Methods Recently extracted primary molars had their proximal surfaces evaluated visually (EC) and classified as healthy surface (0), signs that suggest the presence of carious lesions in enamel (1), signs of a superficial lesion in dentin (2) and carious lesions in deep dentin (3). Results The results were obtained by consensus between the investigators. The gold standard was determined by histological analysis. The values of sensitivity, specificity, accuracy and area under the ROC (Receiver Operating Characteristic) curve were evaluated. There was equilibrium between sensitivity (76.92% EC and 88.46% ER) and specificity (95.83% EC and 95.83% ER). Accuracy was 86.01% (EC) and 88.46% (ER). The Spearman correlation test was used to prove the correlation between clinical and radiographic examinations (0.886), for clinical and histological (0.736) and for radiographic and histological analysis (0.843).

Pulsing With Low Concentration Gibberellin Plus Benzyladenine or Commercial Floral Preservatives Affect Postharvest Longevity, Quality, and Leaf Chlorosis of Cut Lilies and Gladioli

Effects of pulsing with different concentrations of gibberellin plus benzyladenine (GA(4+7) + BA), a proprietary mixture of GA(4+7) plus BA in a commercial floral preservative (GA(4+7) + BA + preservative), or a propriety mixture of sugar plus acidifier developed for bulbous flowers (floral bulb preservative) were studied on postharvest performance and quality of cut lily (Lilium hybrids) and gladiolus ( Gladiolus hybrids) flowers. Pulsing of cut stems of lily with GA(4+7) + BA at 5 or 2 mL.L-1 GA(4+7) + BA + preservative for 20 hours at 3 +/- 1 degrees C extended the vase life and controlled leaf chlorosis of 'Cobra'oriental lily and 'Cappuccino'and Pot Corn'asiatic lily. Cut 'Orange Art'asiatic lily performed best when pulsed with GA(4+7) + BA at 10 mg.L-1. For cut gladiolus, pulsing with GA(4+7) + BA at 10 mg.L-1 extended the vase life of 'Alice', 'Mammoth', and 'Passion', while 'Scarlet'had the longest vase life when pulsed with 5 mg.L-1 GA(4+7) + BA. GA(4+7) + BA + preservative also extended the vase life and controlled leaf chlorosis, but the floral bulb preservative had no effect on vase life extension or preventing leaf chlorosis of lilies. Gladiolus cultivars had no or minor leaf chlorosis during vase period. Overall, overnight pulsing with GA(4+7) + BA + or GA(4+7) + BA + preservative extended the vase life and prevented leaf chlorosis

Escape depth of secondary electrons from electron-irradiated polymers

Measurements on polymers (Teflon FEP and Mylar) have shown that the secondary electron emission from uncharged surfaces exceeds that from surfaces containing a positive surface charge. The reduced emission of charged surfaces is due to recombination between electrons undergoing emission and trapped holes within the charged layer. During the experiments the surface of the material was kept at a negative potential to assure that all secondary electrons reaching the surface from within the material are actually emitted. An analysis of the results yielded the maximum escape depth of the secondary electrons, and showed that the ratio of the maximum escape depth of the secondaries from Mylar to the maximum escape depth from Teflon is almost the same as the ratio of the corresponding second crossover energies of this polymers.

Dependence of brittle-to-ductile transition on crystallographic direction in diamond turning of single-crystal silicon

The objective of this paper is to show the dependence relationship between the crystallographic orientations upon brittle-to-ductile transition during diamond turning of monocrystalline silicon. Cutting tests were performed using a -5 degrees rake angle round nose diamond tool at different machining scales. At the micrometre level, the feedrate was kept constant at 2.5 micrometres per revolution (mu m/r), and the depth of cut was varied from 1 to 5 mu m. At the submicrometre level, the depth of cut was kept constant at 500 nm and the feedrate varied from 5 to 10 mu m/r. At the micrometre level, the uncut shoulder generated with an interrupted cutting test procedure provided a quantitative measurement of the ductile-to-brittle transition. Results show that the critical chip thickness in silicon for ductile material removal reaches a maximum of 285 nm in the [100] direction and a minimum of 115 nm in the [110] direction, when the depth of cut was 5 mu m. It was found that when a submicrometre depth of cut was applied, microcracks were revealed in the [110] direction, which is the softer direction in silicon. Micro Raman spectroscopy was used to estimate surface residual stress after machining. Compressive residual stress in the range 142 MPa and smooth damage free surface finish was probed in the [100] direction for a depth of cut of 5 mu m, whereas residual stresses in the range 350 MPa and brittle damage was probed in the [110] direction for a depth of cut of 500 nm.

Influence of HSM cutting parameters on the surface integrity characteristics of hardened AISI H13 steel

The purpose of this study is to evaluate the influence of the cutting parameters of high-speed machining milling on the characteristics of the surface integrity of hardened AISI H13 steel. High-speed machining has been used intensively in the mold and dies industry. The cutting parameters used as input variables were cutting speed (v c), depth of cut (a p), working engagement (a e) and feed per tooth (f z ), while the output variables were three-dimensional (3D) workpiece roughness parameters, surface and cross section microhardness, residual stress and white layer thickness. The subsurface layers were examined by scanning electron and optical microscopy. Cross section hardness was measured with an instrumented microhardness tester. Residual stress was measured by the X-ray diffraction method. From a statistical standpoint (the main effects of the input parameters were evaluated by analysis of variance), working engagement (a e) was the cutting parameter that exerted the strongest effect on most of the 3D roughness parameters. Feed per tooth (f z ) was the most important cutting parameter in cavity formation. Cutting speed (v c) and depth of cut (a p) did not significantly affect the 3D roughness parameters. Cutting speed showed the strongest influence on residual stress, while depth of cut exerted the strongest effect on the formation of white layer and on the increase in surface hardness.

Solutions to common issues in widefield microscopy: vignetting, mosaicing and depth of focus

In this thesis we have developed solutions to common issues regarding widefield microscopes, facing the problem of the intensity inhomogeneity of an image and dealing with two strong limitations: the impossibility of acquiring either high detailed images representative of whole samples or deep 3D objects. First, we cope with the problem of the non-uniform distribution of the light signal inside a single image, named vignetting. In particular we proposed, for both light and fluorescent microscopy, non-parametric multi-image based methods, where the vignetting function is estimated directly from the sample without requiring any prior information. After getting flat-field corrected images, we studied how to fix the problem related to the limitation of the field of view of the camera, so to be able to acquire large areas at high magnification. To this purpose, we developed mosaicing techniques capable to work on-line. Starting from a set of overlapping images manually acquired, we validated a fast registration approach to accurately stitch together the images. Finally, we worked to virtually extend the field of view of the camera in the third dimension, with the purpose of reconstructing a single image completely in focus, stemming from objects having a relevant depth or being displaced in different focus planes. After studying the existing approaches for extending the depth of focus of the microscope, we proposed a general method that does not require any prior information. In order to compare the outcome of existing methods, different standard metrics are commonly used in literature. However, no metric is available to compare different methods in real cases. First, we validated a metric able to rank the methods as the Universal Quality Index does, but without needing any reference ground truth. Second, we proved that the approach we developed performs better in both synthetic and real cases.