Development of methods for the determination of cadmium and thallium in oil shale by-products with graphite furnace atomic absorption spectrometry using direct analysis.

2014

Applicability of pebble matrix filtration for the pre-treatment of surface waters containing high turbidity and NOM

Purification of drinking water is routinely achieved by use of conventional coagulants and disinfection procedures. However, there are instances such as flood events when the level of turbidity reaches extreme levels while NOM may be an issue throughout the year. Consequently, there is a need to develop technologies which can effectively treat water of high turbidity during flood events and natural organic matter (NOM) content year round. It was our hypothesis that pebble matrix filtration potentially offered a relatively cheap, simple and reliable means to clarify such challenging water samples. Therefore, a laboratory scale pebble matrix filter (PMF) column was used to evaluate the turbidity and natural organic matter (NOM) pre-treatment performance in relation to 2013 Brisbane River flood water. Since the high turbidity was only a seasonal and short term problem, the general applicability of pebble matrix filters for NOM removal was also investigated. A 1.0 m deep bed of pebbles (the matrix) partly in-filled with either sand or crushed glass was tested, upon which was situated a layer of granular activated carbon (GAC). Turbidity was measured as a surrogate for suspended solids (SS), whereas, total organic carbon (TOC) and UV Absorbance at 254 nm were measured as surrogate parameters for NOM. Experiments using natural flood water showed that without the addition of any chemical coagulants, PMF columns achieved at least 50% turbidity reduction when the source water contained moderate hardness levels. For harder water samples, above 85% turbidity reduction was obtained. The ability to remove 50% turbidity without chemical coagulants may represent significant cost savings to water treatment plants and added environmental benefits accrue due to less sludge formation. A TOC reduction of 35-47% and UV-254 nm reduction of 24-38% was also observed. In addition to turbidity removal during flood periods, the ability to remove NOM using the pebble matrix filter throughout the year may have the benefit of reducing disinfection by-products (DBP) formation potential and coagulant demand at water treatment plants. Final head losses were remarkably low, reaching only 11 cm at a filtration velocity of 0.70 m/h.

Optimal scheduling of multiple chlorine sources in water distribution systems

The specified range of free chlorine residual (between minimum and maximum) in water distribution systems needs to be maintained to avoid deterioration of the microbial quality of water, control taste and/or odor problems, and hinder formation of carcino-genic disinfection by-products. Multiple water quality sources for providing chlorine input are needed to maintain the chlorine residuals within a specified range throughout the distribution system. The determination of source dosage (i.e., chlorine concentrations/chlorine mass rates) at water quality sources to satisfy the above objective under dynamic conditions is a complex process. A nonlinear optimization problem is formulated to determine the chlorine dosage at the water quality sources subjected to minimum and maximum constraints on chlorine concentrations at all monitoring nodes. A genetic algorithm (GA) approach in which decision variables (chlorine dosage) are coded as binary strings is used to solve this highly nonlinear optimization problem, with nonlinearities arising due to set-point sources and non-first-order reactions. Application of the model is illustrated using three sample water distribution systems, and it indicates that the GA,is a useful tool for evaluating optimal water quality source chlorine schedules.

Optimization of HS-SPME analytical conditions using factorial design for trihalomethanes determination in swimming pool water samples

Trihalomethanes (THMs) are widely referred and studied as disinfection by-products (DBPs). The THMs that are most commonly detected are chloroform (TCM), bromodichloromethane (BDCM), chlorodibromomethane (CDBM), and bromoform (TBM). Several studies regarding the determination of THMs in swimming pool water and air samples have been published. This paper reviews the most recent work in this field, with a special focus on water and air sampling, sample preparation and analytical determination methods. An experimental study has been developed in order to optimize the headspace solid-phasemicroextraction (HS-SPME) conditions of TCM, BDCM, CDBM and TBM from water samples using a 23 factorial design. An extraction temperature of 45 °C, for 25min, and a desorption time of 5 min were found to be the best conditions. Analysis was performed by gas chromatography with an electron capture detector (GC-ECD). The method was successfully applied to a set of 27 swimming pool water samples collected in the Oporto area (Portugal). TCM was the only THM detected with levels between 4.5 and 406.5 μg L−1. Four of the samples exceeded the guideline value for total THMs in swimming pool water (100 μgL−1) indicated by the Portuguese Health Authority.

Approche multidisciplinaire pour l’amélioration de l’estimation de l’exposition aux sous-produits de désinfection de l’eau en milieu domestique et en piscine

La désinfection de l’eau de consommation et des piscines induit la formation de sous-produits (SPD) potentiellement nocifs pour la santé, parmi lesquels les trihalométhanes (THM), les acides haloacétiques (HAA) et les chloramines (CAM). La difficulté d’estimer l’exposition humaine à ces SPD empêche de cerner précisément les risques sanitaires possiblement associés (i.e., cancérigènes, reprotoxiques, irritatifs). Nos travaux s’articulent autour d’une méthodologie consistant à intégrer des données d’occurrence environnementales à des modèles toxicocinétiques à base physiologique (TCBP) pour améliorer les mesures de l’exposition aux SPD. Cette approche multidisciplinaire veut prendre en compte de manière aussi appropriée que possible les deux composantes majeures des variations de cette exposition : les variations spatio-temporelles des niveaux de contamination environnementale et l’impact des différences inter- et intra-individuelles sur les niveaux biologiques. Cette thèse, organisée en deux volets qui explorent chacun successivement des aspects environnemental et biologique de la problématique, vise à contribuer au développement de cette stratégie innovante d’estimation de l’exposition et, plus généralement, à des meilleures pratiques en la matière. Le premier volet de la thèse s’intéresse à l’exposition en milieu domestique (i.e., résultant de l’utilisation de l’eau potable au domicile) et est consacré au cas complexe des THM, les plus abondants et volatils des SPD, absorbables par ingestion mais aussi par inhalation et voie percutanée. Les articles I et II, constitutifs de ce volet, documentent spécifiquement la question des variations inter- et intra- journalières de présence des SPD en réseau et de leurs impacts sur les estimateurs de l’exposition biologique. Ils décrivent l’amplitude et la diversité des variations à court terme des niveaux environnementaux, présentent les difficultés à proposer une façon systématique et « épidémiologiquement » pratique de les modéliser et proposent, de manière originale, une évaluation des mésestimations, somme toute modestes, des mesures biologiques de l’exposition résultant de leurs non-prise en compte. Le deuxième volet de la thèse se penche sur l’exposition aux SPD en piscine, d’un intérêt grandissant au niveau international, et se restreint au cas jugé prioritaire des piscines publiques intérieures. Ce volet envisage, pour quantifier l’exposition dans ce contexte particulier, l’extension de l’approche méthodologique préconisée, élaborée originellement pour application dans un contexte domestique : d’abord, à travers une analyse approfondie des variations des niveaux de contamination (eau, air) des SPD en piscine en vue de les modéliser (article III); puis en examinant, dans le cas particulier du chloroforme, le THM le plus abondant, la possibilité d’utiliser la modélisation TCBP pour simuler des expositions en piscine (article IV). Les résultats mettent notamment en évidence la difficulté d’appréhender précisément la contamination environnementale autrement que par un échantillonnage in situ tandis que la modélisation TCBP apparait, sur le plan toxicologique, comme l’outil le plus pertinent à ce jour, notamment au regard des autres approches existantes, mais qu’il convient d’améliorer pour mieux prédire les niveaux d’exposition biologique. Finalement, ces travaux illustrent la pertinence et la nécessité d’une approche multidisciplinaire et intégratrice et suggère, sur cette base, les pistes à explorer en priorité pour mieux évaluer l’exposition aux SPD et, in fine, cerner véritablement les risques sanitaires qui en résultent.

A comparison of the role of two blue-green algae in THM and HAA formation

The contribution of two blue-green algae species, Anabaeria flos-aquae and Microcystis aeruginosa, to the formation of trihalomethanes (THMs) and haloacetic acids (HAAs) was investigated. The experiments examined the formation potential of these disinfection by-products (DBPs) from both algae cells and extracellular organic matter (EOM) during four algal growth phases. Algal cells and EOM of Anabaena and Microcystis exhibited a high potential for DBP formation. Yields of total THMs (TTHM) and total HAAs (THAA) were closely related to the growth phase. Reactivity of EOM from Anabaena was slightly higher than corresponding cells, while the opposite result was found for Microcystis. Specific DBP yields (yield/unit C) of Anabaena were in the range of 2-11 mu mol/mmol C for TTHM and 217 mu mol/mmol C for THAA, while those of Microcystis were slightly higher. With regard to the distributions of individual THM and HAA compounds, differences were observed between the algae species and also between cells and EOM. The presence of bromide shifted the dominant compounds from HAAs to THMs. (C) 2009 Elsevier Ltd. All rights reserved.

Assessment of potential climate change impacts on peatland dissolved organic carbon release and drinking water treatment from laboratory experiments

Catchments draining peat soils provide the majority of drinking water in the UK. Over the past decades, concentrations of dissolved organic carbon (DOC) have increased in surface waters. Residual DOC can cause harmful carcinogenic disinfection by-products to form during water treatment processes. Increased frequency and severity of droughts combined with and increased temperatures expected as the climate changes, have potentials to change water quality. We used a novel approach to investigate links between climate change, DOC release and subsequent effects on drinking water treatment. We designed a climate manipulation experiment to simulate projected climate changes and monitored releases from peat soil and litter, then simulated coagulation used in water treatment. We showed that the ‘drought’ simulation was the dominant factor altering DOC release and affected the ability to remove DOC. Our results imply that future short-term drought events could have a greater impact than increased temperature on DOC treatability.

Simulated climate change impact on summer dissolved organic carbon release from peat and surface vegetation: implications for drinking water treatment

Uncertainty regarding changes in dissolved organic carbon (DOC) quantity and quality has created interest in managing peatlands for their ecosystem services such as drinking water provision. The evidence base for such interventions is, however, sometimes contradictory. We performed a laboratory climate manipulation using a factorial design on two dominant peatland vegetation types (Calluna vulgaris and Sphagnum Spp.) and a peat soil collected from a drinking water catchment in Exmoor National Park, UK. Temperature and rainfall were set to represent baseline and future conditions under the UKCP09 2080s high emissions scenario for July and August. DOC leachate then underwent standard water treatment of coagulation/flocculation before chlorination. C. vulgaris leached more DOC than Sphagnum Spp. (7.17 versus 3.00 mg g−1) with higher specific ultraviolet (SUVA) values and a greater sensitivity to climate, leaching more DOC under simulated future conditions. The peat soil leached less DOC (0.37 mg g−1) than the vegetation and was less sensitive to climate. Differences in coagulation removal efficiency between the DOC sources appears to be driven by relative solubilisation of protein-like DOC, observed through the fluorescence peak C/T. Post-coagulation only differences between vegetation types were detected for the regulated disinfection by-products (DBPs), suggesting climate change influence at this scale can be removed via coagulation. Our results suggest current biodiversity restoration programmes to encourage Sphagnum Spp. will result in lower DOC concentrations and SUVA values, particularly with warmer and drier summers.

The use of polyacrylamides (PAMs) for removing natural organic matter (NOM) from Paraiba do Sul River (Brazil)

This work assesses the efficiency of polyacrylamides for natural organic matter (NOM) removal from Paraiba do Sul River (Brazil) raw water for drinking purposes. Jar tests were performed following an experimental design protocol. Three kinds of polyacrylamides (anionic, cationic, and non-ionic) at 0.2 mg L(-1) were tested. After coagulation, turbidity, DOC, UVA(254) and SCAN (UV-absorbing material) were determined. Color and pH were also measured. It was found that polyacrylamides did not reduce the amounts of alum and lime needed in the process and that the amount of alum alone for removing UV-absorbing organic matter is significantly higher. Efficiency of the coagulation process decreased as follows: non-ionic -> cationic -> anionic -> no polyacrylamide. Removal efficiencies for the best case were: 100%, 90%, 83%, and 68% for turbidity, DOC, UVA(254), and SCAN, respectively.

Risk assessment of trihalomethanes from tap water in Fortaleza, Brazil

The cancer risks (CR) by oral ingestion, dermal absorption, and inhalation exposure of trihalomethanes (THM) from tap water of ten districts in Fortaleza, Brazil were estimated. The mean levels of THM compounds were obtained in Fortaleza tap water as follow: 63.9 mu g L(-1) for chloroform (CHCl(3)), 40.0 mu g L(-1) for bromodichloromethane (CHBrCl(2)), and 15.6 mu g L(-1) for dibromochloromethane (CHBr(2)Cl). Bromoform (CHBr(3)) was not detected. The mean CR for THMs in tap water is 3.96 x 10(-4). The results indicate that Fortaleza residents have a higher CR by inhalation than dermal absorption and oral ingestion. The CR for CHCl(3) contributes with 68% as compared with the total CR, followed by CHBrCl(2) (21%), and CHBr(2)Cl (11%). The hazard index (HI) is about ten times lower than unity, not indicating non-cancer effects.

Presença de trihalometanos e qualidade sanitária da água nas estações de tratamento e reservatórios domiciliares nos municípios de Araraquara e Bariri/SP

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Tratamientos avanzados de agua potable para eliminación de materia orgánica disuelta : aplicación del BAC

Los procesos de biofiltración por carbón activo biológico se han utilizado desde hace décadas, primeramente en Europa y después en Norte América, sin embargo no hay parámetros de diseño y operación específicos que se puedan utilizar de guía para la biofiltración. Además, el factor coste a la hora de elegir el carbón activo como medio de filtración impacta en el presupuesto, debido al elevado coste de inversión y de regeneración. A la hora de diseñar y operar filtros de carbón activo los requisitos que comúnmente se buscan son eliminar materia orgánica, olor, y sabor de agua. Dentro de la eliminación de materia orgánica se precisa la eliminación necesaria para evitar subproductos en la desinfección no deseados, y reducir los niveles de carbono orgánico disuelto biodegradable y asimilable a valores que consigan la bioestabilidad del agua producto, a fin de evitar recrecimiento de biofilm en las redes de distribución. El ozono se ha utilizado durante años como un oxidante previo a la biofiltración para reducir el olor, sabor, y color del agua, oxidando la materia orgánica convirtiendo los compuestos no biodegradables y lentamente biodegradables en biodegradables, consiguiendo que puedan ser posteriormente eliminados biológicamente en los filtros de carbón activo. Sin embargo la inestabilidad del ozono en el agua hace que se produzcan ácidos carboxilos, alcoholes y aldehídos, conocidos como subproductos de la desinfección. Con esta tesis se pretende dar respuesta principalmente a los siguientes objetivos: análisis de parámetros requeridos para el diseño de los filtros de carbón activo biológicos, necesidades de ozonización previa a la filtración, y comportamiento de la biofiltración en un sistema compuesto de coagulación sobre un filtro de carbón activo biológico. Los resultados obtenidos muestran que la biofiltración es un proceso que encaja perfectamente con los parámetros de diseño de plantas con filtración convencional. Aunque la capacidad de eliminación de materia orgánica se reduce a medida que el filtro se satura y entra en la fase biológica, la biodegradación en esta fase se mantienen estable y perdura a lo lago de los meses sin preocupaciones por la regeneración del carbón. Los valores de carbono orgánico disuelto biodegradable se mantienen por debajo de los marcados en la literatura existente para agua bioestable, lo que hace innecesaria la dosificación de ozono previa a la biofiltración. La adición de la coagulación con la corrección de pH sobre el carbón activo consigue una mejora en la reducción de la materia orgánica, sin afectar a la biodegradación del carbón activo, cumpliendo también con los requerimientos de turbidez a la salida de filtración. Lo que plantea importantes ventajas para el proceso. Granular activated carbon filters have been used for many years to treat and produce drinking water using the adsorption capacity of carbon, replacing it once the carbon lost its adsorption capacity and became saturated. On the other hand, biological activated carbon filters have been studied for decades, firstly in Europe and subsequently in North America, nevertheless are no generally accepted design and operational parameters documented to be used as design guidance for biofiltration. Perhaps this is because of the cost factor; to choose activated carbon as a filtration media requires a significant investment due to the high capital and regeneration costs. When activated carbon filters are typically required it is for the reduction of an organic load, removal of colour, taste and / or odour. In terms of organic matter reduction, the primary aim is to achieve as much removal as possible to reduce or avoid the introduction of disinfection by products, the required removal in biodegradable dissolved organic carbon and assimilable organic carbon to produce a biologically stable potable water which prohibits the regrowth of biofilm in the distribution systems. The ozone has historically been used as an oxidant to reduce colour, taste and odour by oxidizing the organic matter and increasing the biodegradability of the organic matter, enhancing the effectiveness of organic removal in downstream biological activated carbon filters. Unfortunately, ozone is unstable in water and reacts with organic matter producing carboxylic acids, alcohols, and aldehydes, known as disinfection by products. This thesis has the following objectives: determination of the required parameters for the design of the biological activated filters, the requirement of ozonization as a pre-treatment for the biological activated filters, and a performance assessment of biofiltration when coagulation is applied as a pretreatment for biological activated carbon filters. The results show that the process design parameters of biofiltration are compatible with those of conventional filtration. The organic matter removal reduces its effectiveness as soon as the filter is saturated and the biological stage starts, but the biodegradation continues steadily and lasts for a long period of time without the need of carbon regeneration. The removal of the biodegradable dissolved organic carbon is enough to produce a biostable water according to the values shown on the existing literature; therefore ozone is not required prior to the filtration. Furthermore, the addition of coagulant and pH control before the biological activated carbon filter achieves a additional removal of organic matter, without affecting the biodegradation that occurs in the activated carbon whilst also complying with the required turbidity removal.

Reduction of haloacetonitriles and haloacetones in natural waters using ceramic nanofiltration membranes

Póster presentado en 19th International Congress of Chemical and Process Engineering, Prague, Czech Republic August 28th-September 1st, 2010.

Effect of gamma-irradiation on total organic carbon and trihalomethane formation potential

This research was conducted to study the use of radiation in water treatment as an alternative to chlorination which has caused health concerns due to the formation of harmful disinfection by-products. Groundwater solutions from the Biscayne aquifer were radiated with Cobalt-60 gamma radiation and studied for changes in dissolved organic carbon (DOC), UV absorbance at 254 nm (UV254), fluorescence and trihalomethane formation potential (THMFP). Molecular fractionations were conducted by ultrafiltration. Effect of the combination of radiation/peroxide was studied for DOC and UV254. Radiation showed significant removal in DOC and THMFP. Similar results were seen in the fluorescence and UV absorbance experiments. Radiation/peroxide did not improve the DOC removal. Radiation of the groundwater samples broke the larger molecular weight fractions in to smaller fractions.

Changes in roughness of denture base and reline materials by chemical disinfection or microwave irradiation: Surface roughness of denture base and reline materials

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)