Usinabilidade e integridade superficial de implantes dentários

Pós-graduação em Engenharia Mecânica - FEIS

Análise do processo de fresamento de MDF em centro de usinagem CNC

Pós-graduação em Engenharia Mecânica - FEG

Utilização de metaheurísticas combinada a diferentes métodos de aglutinação para a otimização de um processo de torneamento com múltiplas respostas

Pós-graduação em Engenharia Mecânica - FEG

Contribuição ao estudo do desgaste de bedames na usinagem de ligas de alumínio-silício

Pós-graduação em Engenharia Mecânica - FEIS

Análise do acabamento superficial e força de corte no torneamento de alumina a verde

In experimental conditions, cutting forces were studied during turning of green alumina billets, including their correlation with surface aspects of the workpiece. The correlation between cutting power and the removal rate are important parameters for defining the design of ceramic products, since inadequate parameters can produce excessive surface damage to the workpiece. This study examined the forces obtained during turning of alumina workpieces with 99.8% purity in their green state, by means of a three-point dynamometer, evaluating the cutting, feed and depth forces, using a cermet tool under constant machining conditions. Variables were compared with the forces, including surface finish, tool wear and temperature during machining. In the study, it was found that the depth of cut had no significant effect on the surface quality, and the cutting speed and feed influencing the finish. However, preliminary tests for selecting the cutting conditions showed that unsuitables cutting speeds and feeds generate severe damage to the workpiece surface. The best condition was 1.00 mm depth of cut, and the forces increasedfor with each pass performed, with the feed force the variable with greatest increases in relation to the cutting and depth forces, and wear of the cutting tool directly influenced the surface finish, generated by the highly abrasive nature of the alumina particles of the green compact. It is emphasized that the alumina in its green state showed high abrasive effect on the cutting tool during the turning process and the surface finishing of the green workpiece had a direct influence on the sintered workpiece.

Estudo da aplicação de mínima quantidade de fluido no fresamento de acabamento da liga Ti-6Al-4V

Pós-graduação em Engenharia Mecânica - FEG

A influência das variáveis do lixamento tubular na qualidade das peças de Eucalyptus grandis

In 2010, the Brazilian forest sector is represented by about 30,000 companies producing US$ 21 billion annually and account for approximately 5% of the gross domestic product (GDP) in the country. The sanding process is highly demanded in various stages of industrialization of the wood, when there is a need for a better quality surface finishing. The objective of this work was to analyze the influence of cutting speed and sandpaper granulometry on both the surface finishing of pieces of Eucalyptus grandis processed through tubular sanding and on the sanding efforts (force and power of sanding). Four cutting speeds were used (19.5, 22.7, 26 and 28.1 m/s), one advance speed (16 m/min) and three sets of sandpaper (80-100, 80-120 and 100-120) being one for chipping and another for finishing, respectively. A central data acquisition system was set up to capture the variables (cutting power, acoustic emission and vibration) in real time. The cutting force was obtained indirectly, through a frequency inverter. The roughness of the parts was measured by a roughness meter before and after sanding. The highest cutting speed used (28.1 m/s) consumed more power and generated more acoustic emission among the four speeds tested. Regarding the vibration, the lower cutting speed (19.5 m/ s) generated the highest vibration in the sander machine. It is concluded that the range of 100-120 sandpapers resulted in values of average roughness (Ra) lower than the other sets of sandpaper used, as it resulted in better surface finishing.

Análise do acabamento superficial e da potência consumida na usinagem de fresamento frontal e cilíndrico tangencial da madeira de eucalipto

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Utilização da função desirability na otimização do processo de usinagem da superliga NIMONIC 80A

In the current economic scenario, it is important to the incessant search for improvements in production quality and also in reducing costs. The great competition and technological innovation makes customers stay more and more demanding and seek multiple sources of improvement in production. The work aimed to use the general desirability to optimize a process involving multiple answers in machining experiment. The process of cylindrical turning is one of the most common processes of metal cutting machining and involves several factors, in which will be analysed the best combination of the input factors in machining process, with variable response to surface roughness (Ra) and cutting length (Lc) that vary important answers to measure process efficiency and product quality. The method is a case study, since it involves a study of a tool well addressed in the literature. Data analysis was used in the process of doctoral thesis of Ricardo Penteado on the theme using metaheuristicas combined with different methods of bonding for the optimization of a turning process of multiple responses, then used the desirability and analysis tool. Joint optimization by desirability, the method proposed the following combination of input variables, variable cutting speed at 90 m/min ( -1 level), the breakthrough in 0, 12 mm/revol. ( -1 level), the machining depth should be in 1.6 mm (level 1), gum used must be the TP2500 ( -1 level), in abundant fluid (level 1) and laminated material (level 1) to the maximization of the cutting length (Lc) and minimization of roughness (Ra)

Estudo da utilização de ferramentas a base de nitreto de silício (Si3N4) e alumina (Al2O3) na usinagem do ferro fundido vermicular

Machining is one of the most commonly manufacturing processes used in the modern world, consuming millions of dollars annually. Because of this, it is crucial for the automotive industry to reduce costs on their heat-resistant alloy machining processes, such as compacted graphite iron (CGI), which has shown an increasing trend of its application in diesel engine blocks, brakes disks, among other applications, due to its superior mechanical properties to gray cast iron. Despite this advantage, its use is still limited due to its difficulty of machining, moreover, cutting tools are displayed as the main factor in increasing the machining cost. Seeking an alternative to a better machinability of CGI, this paper aims to study two types of ceramic tools developed in Brazil, and benchmark their performance by dry turning. For this, were used CGI class 450 and two tools: ceramic of silicon nitride (Si3N4) and alumina-based (Al2O3), with a cutting speed (Vc) of 300, 400 and 500 m / min; feed (f) of 0.2 mm / rev and depth of cut (ap) of 0.5 mm, using three replicates and starting with new cutting edges. The results showed that the Al2O3 tool had the best performance in Vc of 500 m / min, while the Si3N4 tool had the best results in Vc of 300 m / min. This can be explained by the tool of Si3N4 based include soft intergranular phase, called amorphous, while alumina has higher abrasion resistance due to its high refractoriness. The results make it clear that the tools have significant potential for machining of compacted graphite iron, being necessary a strict control of the cutting parameters used

Utilização da função desirability na otimização do processo de usinagem da superliga NIMONIC 80A

In the current economic scenario, it is important to the incessant search for improvements in production quality and also in reducing costs. The great competition and technological innovation makes customers stay more and more demanding and seek multiple sources of improvement in production. The work aimed to use the general desirability to optimize a process involving multiple answers in machining experiment. The process of cylindrical turning is one of the most common processes of metal cutting machining and involves several factors, in which will be analysed the best combination of the input factors in machining process, with variable response to surface roughness (Ra) and cutting length (Lc) that vary important answers to measure process efficiency and product quality. The method is a case study, since it involves a study of a tool well addressed in the literature. Data analysis was used in the process of doctoral thesis of Ricardo Penteado on the theme using metaheuristicas combined with different methods of bonding for the optimization of a turning process of multiple responses, then used the desirability and analysis tool. Joint optimization by desirability, the method proposed the following combination of input variables, variable cutting speed at 90 m/min ( -1 level), the breakthrough in 0, 12 mm/revol. ( -1 level), the machining depth should be in 1.6 mm (level 1), gum used must be the TP2500 ( -1 level), in abundant fluid (level 1) and laminated material (level 1) to the maximization of the cutting length (Lc) and minimization of roughness (Ra)

Estudo da utilização de ferramentas a base de nitreto de silício (Si3N4) e alumina (Al2O3) na usinagem do ferro fundido vermicular

Machining is one of the most commonly manufacturing processes used in the modern world, consuming millions of dollars annually. Because of this, it is crucial for the automotive industry to reduce costs on their heat-resistant alloy machining processes, such as compacted graphite iron (CGI), which has shown an increasing trend of its application in diesel engine blocks, brakes disks, among other applications, due to its superior mechanical properties to gray cast iron. Despite this advantage, its use is still limited due to its difficulty of machining, moreover, cutting tools are displayed as the main factor in increasing the machining cost. Seeking an alternative to a better machinability of CGI, this paper aims to study two types of ceramic tools developed in Brazil, and benchmark their performance by dry turning. For this, were used CGI class 450 and two tools: ceramic of silicon nitride (Si3N4) and alumina-based (Al2O3), with a cutting speed (Vc) of 300, 400 and 500 m / min; feed (f) of 0.2 mm / rev and depth of cut (ap) of 0.5 mm, using three replicates and starting with new cutting edges. The results showed that the Al2O3 tool had the best performance in Vc of 500 m / min, while the Si3N4 tool had the best results in Vc of 300 m / min. This can be explained by the tool of Si3N4 based include soft intergranular phase, called amorphous, while alumina has higher abrasion resistance due to its high refractoriness. The results make it clear that the tools have significant potential for machining of compacted graphite iron, being necessary a strict control of the cutting parameters used

Surface integrity analysis when milling ultrafine-grained steels

This paper quantifies the effects of milling conditions on surface integrity of ultrafine-grained steels. Cutting speed, feed rate and depth of cut were related to microhardness and microstructure of the workpiece beneath machined surface. Low-carbon alloyed steel with 10.8 µm (as-received) and 1.7 µm (ultrafine) grain sizes were end milled using the down-milling and dry condition in a CNC machining center. The results show ultrafine-grained workpiece preserves its surface integrity against cutting parameters more than the as-received material. Cutting speed increases the microhardness while depth of cut deepens the hardened layer of the as-received material. Also, deformations of microstructure following feed rate direction were observed in workpiece subsurface.

Estudio experimental del desgaste del flanco y de la rugosidad superficial en el torneado en seco de alta velocidad del acero AISI 316L

La mejora continua de los procesos de fabricación es fundamental para alcanzar niveles óptimos de productividad, calidad y coste en la producción de componentes y productos. Para ello es necesario disponer de modelos que relacionen de forma precisa las variables que intervienen en el proceso de corte. Esta investigación tiene como objetivo determinar la influencia de la velocidad de corte y el avance en el desgaste del flanco de los insertos de carburos recubiertos GC1115 y GC2015 y en la rugosidad superficial de la pieza mecanizada de la pieza en el torneado de alta velocidad en seco del acero AISI 316L. Se utilizaron entre otros los métodos de observación científica, experimental, medición, inteligencia artificial y estadísticos. El inserto GC1115 consigue el mejor resultado de acuerdo al gráfico de medias y de las ecuaciones de regresión múltiple de desgaste del flanco para v= 350 m/min, mientras que para las restantes velocidades el inserto GC2015 consigue el mejor desempeño. El mejor comportamiento en cuanto a la rugosidad superficial de la pieza mecanizada se obtuvo con el inserto GC1115 en las velocidades de 350 m/min y 400 m/min, en la velocidad de 450 m/min el mejor resultado correspondió al inserto GC2015. Se analizaron dos criterios nuevos, el coeficiente de vida útil de la herramienta de corte en relación al volumen de metal cortado y el coeficiente de rugosidad superficial de la pieza mecanizada en relación al volumen de metal cortado. Fueron determinados los modelos de regresión múltiple que permitieron calcular el tiempo de mecanizado de los insertos sin que alcanzaran el límite del criterio de desgaste del flanco. Los modelos desarrollados fueron evaluados por sus capacidades de predicción con los valores medidos experimentalmente. ABSTRACT The continuous improvement of manufacturing processes is critical to achieving optimal levels of productivity, quality and cost in the production of components and products. This is necessary to have models that accurately relate the variables involved in the cutting process. This research aims to determine the influence of the cutting speed and feed on the flank wear of carbide inserts coated by GC1115 and GC2015 and the surface roughness of the workpiece for turning dry high speed steel AISI 316L. Among various scientific methods this study were used of observation, experiment, measurement, statistical and artificial intelligence. The GC1115 insert gets the best result according to the graph of means and multiple regression equations of flank wear for v = 350 m / min, while for the other speeds the GC2015 insert gets the best performance. Two approaches are discussed, the life ratio of the cutting tool relative to the cut volume and surface roughness coefficient in relation to the cut volume. Multiple regression models were determined to calculate the machining time of the inserts without reaching the limit of the criterion flank wear. The developed models were evaluated for their predictive capabilities with the experimentally measured values.

An investigation of the relationship between temperature, forces and tool wear in turning and drilling

Developing a means of predicting tool life has been and continues to be a focus of much research effort. A common experience in attempting to replicate such efforts is an inability to achieve the levels of agreement between theory and practice of the original researcher or to extrapolate the work to different materials or cutting conditions to those originally used. This thesis sets out to examine why most equations or models when replicated do not give good agreements. One reason which was found is that researchers in wear prediction, their predictions are limited because they generally fail to properly identify the nature of wear mechanisms operative in their study. Also they fail to identify or recognise factors having a significant influence on wear such as bar diameter. Also in this research the similarities and differences between the two processes of single point turning and drilling are examined through a series of tests. A literature survey was undertaken in wear and wear prediction. As a result it was found that there was a paucity in information and research in the work of drilling as compared to the turning operation. This was extended to the lack of standards that exist for the drilling operation. One reason for this scarcity in information on drilling is due to the complexity of the drilling and the tool geometry of the drill. In the comparative drilling and turning tests performed in this work, the same tool material; HSS, and similar work material was used in order to eliminate the differences which may occur due to this factor. Results of the tests were evaluated and compared for the two operations and SEM photographs were taken for the chips produced. Specific test results were obtained for the cutting temperatures and forces of the tool. It was found that cutting temperature is influenced by various factors like tool geometry and cutting speed, and the temperature itself influenced the tool wear and wear mechanisms that act on the tool. It was found and proven that bar diameter influences the temperature, a factor not considered previously.