Enhanced stability in CO2 of Ta doped BaCe0.9Y 0.1O3-δ electrolyte for intermediate temperature SOFCs

The influence of Ta concentration on the stability of BaCe 0.9-xTaxY0.1O3-δ (where x=0.01, 0.03 and 0.05) powders and sintered samples in CO2, their microstructure and electrical properties were investigated. The ceramic powders were synthesized by the method of solid state reaction, uniaxially pressed and sintered at 1550 °C to form dense electrolyte pellets. A significant stability in CO2 indicated by the X-ray analysis performed was observed for the samples with x≥0.03. The electrical conductivities determined by impedance measurements in the temperature range of 550-750 °C and in various atmospheres (dry argon, wet argon and wet hydrogen) increased with temperature but decreased with Ta concentration. The highest conductivities were observed in the wet hydrogen atmosphere, followed by those in wet argon, while the lowest were obtained in the dry argon atmosphere for each dopant concentration. The composition with Ta content of 3 mol% showed satisfactory characteristics: good resistance to CO2 in extreme testing conditions, while a somewhat reduced electrical conductivity is still comparable with that of BaCe0.9Y0.1O3-δ. © 2012 Elsevier Ltd and Techna Group S.r.l.

Estudos eletroquímico de filmes híbridos siloxano-PMMA como pré-tratamentos protetores contra corrosão para aço estanhado

Pós-graduação em Química - IQ

Estudo eletroquímico da corrosividade de biodiesel para aço carbono e outros materiais metálicos usados em veículos automotores

Pós-graduação em Química - IQ

Structure and properties of chemically synthesized BiFeO3. Influence of fuel and complexing agent

Perovskite, single multiferroic bismuth ferrite was prepared by two chemical methods: auto-combustion and soft chemical route. Influence of different fuels and complexing agents and thermal treatment on purity of bismuth ferrite powders and density of bismuth ferrite ceramics were investigated. X-ray diffraction technique (XRD) indicated that optimal temperatures and times for calcination and sintering are 600 degrees C for 2 h and 800 degrees C for 1 h with quenching, respectively. Scanning electron microscopy (SEM) analysis showed that soft route synthesized samples formed softer agglomerates and smaller grains with less secondary phases. Powders and pellets were characterized by Brunauer Emmett Teller (BET) specific surface area analysis, particle size distribution, Fourier transform infrared spectroscopy (FT-IR), dilatometry, Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), dielectric and magnetic measurements. Resistivity and origin of electrical resistance were studied by means of impedance measurements. (C) 2014 Elsevier Ltd and Techna Group S.r.l. All rights reserved.

Electrical conductivity of Ag-Na ion exchanged soda-lime glass

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural damage detection in an aeronautical panel using analysis of variance

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Membranas de biocelulose como substrato para o crescimento de nanofios de ZnO: síntese e aplicação

Pós-graduação em Química - IQ

Membranas de biocelulose como substrato para o crescimento de nanofios de ZnO: síntese e aplicação

Pós-graduação em Química - IQ

Characterization of flexible DNA films

Polymer electrolytes (PEs) are currently the focus of much attention as potential electrolytes in electrochemical devices such as batteries, display devices and sensors. Deoxyribonucleic acid (DNA) as an important biological macromolecule has electric conducting electrochemical properties and unique three dimensional structures. With the goal of developing a new family of environmentally friendly multifunctional biohybrid materials displaying simultaneously high ionic conductivity we have produced in the present work, flexible films based on DNA, incorporating ionic liquids (ILs). Over the last decade ILs have been employed as a new media in electrochemistry and electroanalysis. The materials studied here have been characterized by means of Differential Scanning Calorimetry, Complex Impedance Spectroscopy and Cyclic Voltammetry. (C) 2012 Elsevier B.V. All rights reserved.

Performance of an electronic tongue during monitoring 2-rnethylisoborneol and geosmin in water samples

2-Methylisoborneol (MIB) and geosmin (GSM) are sub products from algae decomposition and, depending on their concentration, can be toxic: otherwise, they give unpleasant taste and odor to water. For water treatment companies it is important to constantly monitor their presence in the distributed water and avoid further costumer complaints. Lower-cost and easy-to-read instrumentation would be very promising in this regard. In this study, we evaluate the potentiality of an electronic tongue (ET) system based on non-specific polymeric sensors and impedance measurements in monitoring MIB and GSM in water samples. Principal component analysis (PCA) applied to the generated data matrix indicated that this ET was capable to perform with remarkable reproducibility the discrimination of these two contaminants in either distilled or tap water, in concentrations as low as 25 ng L-1. Nonetheless, this analysis methodology was rather qualitative and laborious, and the outputs it provided were greatly subjective. Also, data analysis based on PCA severely restricts automation of the measuring system or its use by non-specialized operators. To circumvent these drawbacks, a fuzzy controller was designed to quantitatively perform sample classification while providing outputs in simpler data charts. For instance, the ET along with the referred fuzzy controller performed with a 100% hit rate the quantification of MIB and GSM samples in distilled and tap water. The hit rate could be read directly from the plot. The lower cost of these polymeric sensors allied to the especial features of the fuzzy controller (easiness on programming and numerical outputs) provided initial requirements for developing an automated ET system to monitor odorant species in water production and distribution. (C) 2012 Elsevier B.V. All rights reserved.

Self-assembled films from chitosan and poly(vinyl sulfonic acid) on Nafion® for direct methanol fuel cell

Chitosan/poly(vinyl sulfonic acid) (PVS) films have been prepared on Nafion® membranes by the layer-by-layer (LbL) method for use in direct methanol fuel cell (DMFC). Computational methods and Fourier transform infrared (FTIR) spectra suggest that an ionic pair is formed between the sulfonic group of PVS and the protonated amine group of chitosan, thereby promoting the growth of LbL films on the Nafion® membrane as well as partial blocking of methanol. Chronopotentiometry and potential linear scanning experiments have been carried out for investigation of methanol crossover through the Nafion® and chitosan/PVS/Nafion® membranes in a diaphragm diffusion cell. On the basis of electrical impedance measurements, the values of proton resistance of the Nafion® and chitosan/PVS/Nafion® membranes are close due to the small thickness of the LbL film. Thus, it is expected an improved DMFC performance once the additional resistance of the self-assembled film is negligible compared to the result associated with the decrease in the crossover effect.

Photofixierung von Lipidmembranen aus Glykolipopolymeren auf Goldoberflächen

Ziel war Herstellung und Charakterisierung festkörperunterstützter Membransysteme aus Glykolipopolymeren auf Goldoberflächen, mit elektrischen Eigenschaften, die denen der Schwarzfilmmembranen entsprechen. Um diese Eigenschaften mit impedanzspektroskopischen Techniken messen zu können, ist die Präparation der Membranen auf Goldfilmen notwendig. Eine direkte Verankerung der Glykolipopolymermoleküle (GLP) auf der Goldoberfläche ist nicht möglich, daher werden die untersuchten GLP mit Hilfe von photoreaktiven Molekülen kovalent auf der Goldoberfläche immobilisiert. Untersuchten Abstandhalter waren Thio-Polyethylenglykol und eine Mischung zweier Alkanthiole, bestehend aus 1-Thiohexanol und Bis-(Aminododecyl)-disulfid. Thio-PEG-Monoschichten zeigten sehr unterschiedliche Schichtdicken, weil die Moleküle auf der Oberfläche sehr unterschiedliche Konformationen annehmen können, die eine regelmässige Anordnung erschweren. Langmuir-Blodgett Übertrag sowie die durchgeführte photochemische Fixierung der GLP-Moleküle auf Thio-PEG Schichten führte zu Eigenschaften, die auf den Aufbau einer Lipidmonolage hinweisen. Diese stellte jedoch im Bereich der Lipidmoleküle keine geschlossene Schicht dar. Es kommen als Abstandhaltermoleküle für die Photofunktionalisierung nur Moleküle in Frage, die aufgrund ihrer Eigenschaften eine regelmässige Anordnung auf der Goldoberfläche anstreben. Diese Voraussetzung erfüllt am besten die Gruppe der Alkanthiole. Terminal funktionalisierte Alkanthiole müssen jedoch mit nicht oder anderweitig funktionalisierten Alkanthiolen verdünnt assembliert werden, um weitergehende Funktionalisierungen einzugehen. Die untersuchten GLP lassen sich aufgrund ihrer amphiphilen Struktur an der Wasser-Luft Grenzfläche vororientieren. In allen Fällen gelingt auch der Langmuir-Blodgett Übertrag der komprimierten Schicht, sowie, nach der für die Anbindung notwendigen Trocknung, die photochemisch kovalente Fixierung der Monoschicht durch Bestrahlung mit UV-Licht. Damit konnte erstmals die photochemisch kovalente Fixierung von GLPs auf der Goldoberfläche gezeigt werden. Untersuchungen erfolgten an einem Copolymer sowie zwei unterschiedlichen Homopolymermolekülen. Der unterschiedliche molekulare Aufbau der GLP spiegelt sich in ihrem Verhalten an der Wasser-Luft Grenzfläche sowie in den Eigenschaften der gebildeten Monoschichten wieder. Die Copolymer-Schichten zeigten sehr unterschiedliche Schichtdicken. Auch die EIS-Daten sind schlecht reproduzierbar. Dies ist auf die molekulare Struktur des Copolymers zurückzuführen. Gänzlich unterschiedlich verhalten sich die Homopolymere. Aufgrund ihrer Struktur lassen sie sich zu dichten Schichten komprimieren. Messungen der Fluoreszenzerholung nach Photobleichung (FRAP) zeigen homogene aber nicht fluide Schichten. Die photochemisch kovalente Fixierung des Moleküls auf der Goldoberfläche konnte durch SPR- sowie EIS-Messungen nachgewiesen werden. Die EIS-Messungen zeigen Werte, die sich in Bereichen der idealen Modellmembran bewegen. Der erfolgreiche Einbau von Valinomycin konnte bestätigt werden. FRAP Untersuchungen zeigten die Bildung homogener Schichten. Diese sind jedoch im Bereich der proximalen Lipidschicht nicht fluide. Um die Fluidität in Anlehnung an die Eigenschaften der natürlichen Membranen zu erhöhen, wurden die photochemisch kovalent fixierten Anker-Glykolipopolymer-Moleküle durch Mischung mit freien Lipiden lateral verdünnt. Auch die kovalente Fixierung der GLP-Bausteine innerhalb gemischten Schichten konnte erfolgreich demonstriert werden. Die Schichten zeigten sich jedoch, mit Ausnahme der Schichten aus 50mol% Homopolymer und 50mol% Lipid, inhomogen. Nach Photobleichung durch den Laserblitz kam es nur bei den 50mol%:50mol% -Schichten (Ho: Lipid) zur Erholung der Fluoreszenz, was auf das Vorliegen von beweglichen Lipidmolekülen innerhalb der Membran schliessen lässt. Der Versuch der Inkorporation von Valinomycin gelang ebenfalls. Alle genannten Ergebnisse deuten darauf hin, dass die molekulare Architektur der hergestellten Schichten durch die unterschiedlichen Längendimensionen des Homopolymer-Moleküls einerseits, sowie des Lipids andererseits nicht für alle Mischungsverhältnisse ausreichend stabil ist. Die für die kovalente Fixierung erforderliche Trocknung der Schicht führt zu einer deutlichen Verminderung des Wassergehaltes des Systems und einer daraus resultierenden starken Destabilisierung der aufgebauten Schichten. Insgesamt gesehen stellt somit die photochemische Fixierung der glykosidischen Homopolymer-Membranen ein vielversprechendes Modellsystem dar.

Advanced spectroscopic techniques and chemometric analysis for atmospheric organic aerosol characterization and source apportionment

Atmospheric aerosol particles directly impact air quality and participate in controlling the climate system. Organic Aerosol (OA) in general accounts for a large fraction (10–90%) of the global submicron (PM1) particulate mass. Chemometric methods for source identification are used in many disciplines, but methods relying on the analysis of NMR datasets are rarely used in atmospheric sciences. This thesis provides an original application of NMR-based chemometric methods to atmospheric OA source apportionment. The method was tested on chemical composition databases obtained from samples collected at different environments in Europe, hence exploring the impact of a great diversity of natural and anthropogenic sources. We focused on sources of water-soluble OA (WSOA), for which NMR analysis provides substantial advantages compared to alternative methods. Different factor analysis techniques are applied independently to NMR datasets from nine field campaigns of the project EUCAARI and allowed the identification of recurrent source contributions to WSOA in European background troposphere: 1) Marine SOA; 2) Aliphatic amines from ground sources (agricultural activities, etc.); 3) Biomass burning POA; 4) Biogenic SOA from terpene oxidation; 5) “Aged” SOAs, including humic-like substances (HULIS); 6) Other factors possibly including contributions from Primary Biological Aerosol Particles, and products of cooking activities. Biomass burning POA accounted for more than 50% of WSOC in winter months. Aged SOA associated with HULIS was predominant (> 75%) during the spring-summer, suggesting that secondary sources and transboundary transport become more important in spring and summer. Complex aerosol measurements carried out, involving several foreign research groups, provided the opportunity to compare source apportionment results obtained by NMR analysis with those provided by more widespread Aerodyne aerosol mass spectrometers (AMS) techniques that now provided categorization schemes of OA which are becoming a standard for atmospheric chemists. Results emerging from this thesis partly confirm AMS classification and partly challenge it.

Modelling, simulation and characterization of epithelial cell culture biochip

A microfluidic Organ-on-Chip has been developed for monitoring the epithelial cells monolayer. Equivalent circuit Model was used to determine the electrical properties from the impedance spectra of the epithelial cells monolayer. Black platinum on platinum electrodes was electrochemically deposited onto the surface of electrodes to reduce the influence of the electrical double layer on the impedance measurements. Measurements of impedance with an Impedance Analyzer were done to validate the equivalent circuit model and the decrease of the double layer effect. A Lock-in Amplifier was designed to measure the impedance.

Immobilizing bacteriorhodopsin on a single electron transistor

As awareness of potential human and environmental impacts from toxins has increased, so has the development of innovative sensors. Bacteriorhodopsin (bR) is a light activated proton pump contained in the purple membrane (PM) of the bacteria Halobacterium salinarum. Bacteriorhodopsin is a robust protein which can function in both wet and dry states and can withstand extreme environmental conditions. A single electron transistor(SET) is a nano-scale device that exploits the quantum mechanical properties of electrons to switch on and off. SETs have tremendous potential in practical applications due to their size, ultra low power requirements, and electrometer-like sensitivity. The main goal of this research was to create a bionanohybrid device by integrating bR with a SET device. This was achieved by a multidisciplinary approach. The SET devices were created by a combination of sputtering, photolithography, and focused ion beam machining. The bionanomaterial bacteriorhodopsin was created through oxidative fermentation and a series of transmembrane purification processes. The bR was then integrated with the SET by electrophoretic deposition, creating a bionanohybrid device. The bionanohybrid device was then characterized using a semiconductor parametric analyzer. Characterization demonstrated that the bR modulated the operational characteristics of the SET when bR was activated with light within its absorbance spectrum. To effectively integrate bacteriorhodopsin with microelectromechanical systems (MEMS) and nanoelectromechanical systems (NEMS), it is critical to know the electrical properties of the material and to understand how it will affect the functionality of the device. Tests were performed on dried films of bR to determine if there is a relationship between inductance, capacitance, and resistance (LCR) measurements and orientation, light-on/off, frequency, and time. The results indicated that the LCR measurements of the bR depended on the thickness and area of the film, but not on the orientation, as with other biological materials such as muscle. However, there was a transient LCR response for both oriented and unoriented bR which depended on light intensity. From the impedance measurements an empirical model was suggested for the bionanohybrid device. The empirical model is based on the dominant electrical characteristics of the bR which were the parallel capacitance and resistance. The empirical model suggests that it is possible to integrate bR with a SET without influencing its functional characteristics.