Processamento e caracterização de compósitos de resina fenólica com nanotubos de carbono com aplicações aeroespaciais

Este trabalho de pesquisa consistiu na obtenção de compósitos nanoestruturados utilizando matrizes poliméricas termorrígidas e nanotubos de carbono (CNT) e posterior caracterização de suas propriedades mecânicas, térmicas, elétricas, reológicas e demais características físico-químicas para aplicações aeroespaciais. As atividades experimentais para a realização deste trabalho foram, em sua maioria, conduzidas na Alemanha. Durante o desenvolvimento deste trabalho de pesquisa, foi possível entender melhor como deve ser realizada a purificação, funcionalização e dispersão de CNT em compósitos poliméricos. Desta forma, CNT foram caracterizados e utilizados como reforços para a obtenção de compósitos nanoestruturados em matrizes termorrígidas (resina fenólica). Estes compósitos foram processados, por meio de cura em autoclave e avaliados com relação aos seus desempenhos mecânicos, físico-químicos e morfológicos. Duas metodologias foram utilizadas para permitir a dispersão dos CNT: dispersão em solução aquosa e por calandragem (TRC). Os resultados obtidos mostram que a metodologia mais adequada para dispersar os CNT em resina fenólica é a partir do processo por calandragem e que teores superiores a 0,5% em massa de CNT não resultam em melhorias significativas quanto aos desempenhos viscoelástico, térmico, elétrico e mecânico destes compósitos. Ainda, a partir dos ensaios reológicos e elétricos, foi observado que teores abaixo de 0,2% em massa de CNT já são suficientes para promover a percolação dos CNT na resina fenólica, gerando mudanças significativas no comportamento físico-químico do compósito nanoestruturado. A partir deste trabalho de pesquisa...

Processamento do compósito de fibra de capim-sapê / epóxi e avaliação da resistência à flexão “t” de Student

In recent years a great worldwide interest has arisen for the development of new technologies that enable the use of products with less environmental impact. The replacement of synthetic fiber plants is a possibility very important because this fiber is renewable, biodegradable and few cost and cause less environmental impact. Given the above, this work proposes to develop polymeric composites of epoxy resin and study the behavior of these materials. Both, the epoxy resin used as matrix in the manufacture of sapegrass fiber composite, as tree composites formed by: epoxy/unidirectional sapegrass long fiber, 75% epoxy/25% short fiber, by volume, and 80% epoxy/20% short fiber, by volume, were characterized by bending, and the composites produced with short fibers random were inspected by Optical Microscopy and Acoustics Inspection (C-Scan). For the analysis of the sapegrass fiber morphology, composites 75% epoxy/25% short fiber (sheet chopped) and 80% epoxy/20% short fiber images were obtained by optical microscope and the adhesion between polymer/fiber was visualized. As results, the flexural strength of composites epoxy/unidirectional long fibers, 75% epoxy/25% short fiber and 80% epoxy/20% short fiber were 70.36 MPa, 21.26 MPa, 25.07 MPa, respectively. Being that composite showed that the best results was made up of long fibers, because it had a value of higher flexural strength than other composites analyzed

Comportamentos, térmico e mecânico, de compósitos de polipropileno e resíduo da hidrólise enzimática do bagaço de cana de açúcar

Pós-graduação em Engenharia Mecânica - FEG

Compósitos preparados a partir de resíduo industrial de couro com elastômeros termoplásticos obtidos através de blendas de polietileno de baixa densidade e borracha natural

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento e caracterização de compósitos poli(tereftalato de etileno) reciclado (PET reciclado) com flocos de vidro.

The growing concern with the solid residues management, observed in the last decade, due to its huge amount and impact, has motivated the search for recycling processes, where these residues can be reprocessed to generate new products, enlarging the cycle of materials and energy which are present. Among the polymeric residues, there is poly (ethylene terephthalate) (PET). PET is used in food packaging, preferably in the bottling of carbonated beverages. The reintegration of post-consumer PET in half can be considered a productive action mitigation of environmental impacts caused by these wastes and it is done through the preparation of several different products at the origin, i.e. food packaging, with recycling rates increasing to each year. This work focused on the development and characterization mechanical, thermal, thermo-mechanical, dynamic mechanical thermal and morphology of the pure recycled PET and recycled PET composites with glass flakes in the weight fraction of 5%, 10% and 20% processed in a single screw extruder, using the following analytical techniques: thermogravimetry (TG), differential scanning calorimetry (DSC), tensile, Izod impact, Rockwell hardness, Vicat softening temperature, melt flow rate, burn rate, dynamic mechanical thermal analysis (DMTA) and scanning electron microscopy (SEM). The results of thermal analysis and mechanical properties leading to a positive evaluation, because in the thermograms the addition of glass flakes showed increasing behavior in the initial temperatures of thermal decomposition and melting crystalline, Furthermore was observed growing behavior in the mechanical performance of polymer composites, whose morphological structure was observed by SEM, verifying a good distribution of glass flakes, showing difference orientation in the center and in the surface layer of test body of composites with 10 and 20% of glass flakes. The results of DMTA Tg values of the composites obtained from the peak of tan ä showed little reductions due to poor interfacial adhesion between PET and recycled glass flakes.

Processamento e caracterização de compósitos Poli(METACRILATO DE METILA)/Sílica (PMMA/SiO2)

Currently the search for new materials with properties suitable for specific applications has increased the number of researches that aim to address market needs. The poly (methyl methacrylate) (PMMA) is one of the most important polymers of the family of polyacrylates and polymethacrylates, especially for its unique optical properties and weathering resistance, and exceptional hardness and gloss. The development of polymer composites by the addition of inorganic fillers to the PMMA matrix increases the potential use of this polymer in various fields of application. The most commonly used inorganic fillers are particles of silica (SiO2), modified clays, graphite and carbon nanotubes. The main objective of this work is the development of PMMA/SiO2 composites at different concentrations of SiO2, for new applications as engineering plastics. The composites were produced by extrusion of tubular film, and obtained via solution for application to commercial PMMA plates, and also by injection molding, for improved the abrasion and scratch resistance of PMMA without compromising transparency. The effects of the addition of silica particles in the polymer matrix properties were evaluated by the maximum tensile strength, hardness, abrasion and scratch resistance, in addition to preliminary characterization by torque rheometry and melt flow rate. The results indicated that it is possible to use silica particles in a PMMA matrix, and a higher silica concentration produced an increase of the abrasion and scratch resistance, hardness, and reduced tensile strength

Comportamento magnético de compósitos de matriz polimérica com adição de ferritas

Polymer matrix composites offer advantages for many applications due their combination of properties, which includes low density, high specific strength and modulus of elasticity and corrosion resistance. However, the application of non-destructive techniques using magnetic sensors for the evaluation these materials is not possible since the materials are non-magnetizable. Ferrites are materials with excellent magnetic properties, chemical stability and corrosion resistance. Due to these properties, these materials are promising for the development of polymer composites with magnetic properties. In this work, glass fiber / epoxy circular plates were produced with 10 wt% of cobalt or barium ferrite particles. The cobalt ferrite was synthesized by the Pechini method. The commercial barium ferrite was subjected to a milling process to study the effect of particle size on the magnetic properties of the material. The characterization of the ferrites was carried out by x-ray diffraction (XRD), field emission gun scanning electron microscopy (FEG-SEM) and vibrating sample magnetometry (VSM). Circular notches of 1, 5 and 10 mm diameter were introduced in the composite plates using a drill bit for the non-destructive evaluation by the technique of magnetic flux leakage (MFL). The results indicated that the magnetic signals measured in plates with barium ferrite without milling and cobalt ferrite showed good correlation with the presence of notches. The milling process for 12 h and 20 h did not contribute to improve the identification of smaller size notches (1 mm). However, the smaller particle size produced smoother magnetic curves, with fewer discontinuities and improved signal-to-noise ratio. In summary, the results suggest that the proposed approach has great potential for the detection of damage in polymer composites structures

Plásticos reforçados a base de tecidos híbridos: efeitos da anisotropia e geometria normativa na caracterização mecânica e da fratura

As most current studies, reinforced plastics have been, in recent years, a viable alternative in building structural elements of medium and large, since the lightness accompanied by high performance possible. The design of hybrid polymer composites (combination of different types of reinforcements) may enable structural applications thereof, facing the most severe service conditions. Within this class of composite materials, reinforced the underlying tissues hybrid high performance are taking space when your application requires high load bearing and high rigidity. The objective of this research work is to study the challenges in designing these fabrics bring these materials as to its mechanical characterization and fracture mechanisms involved. Some parameters associated with the process and / or form of hybridization stand out as influential factors in the final performance of the material such as the presence of anisotropy, so the fabric weave, the process of making the same, normative geometry of the specimens, among others. This sense, four laminates were developed based hybrid reinforcement fabrics involving AS4 carbon fiber, kevlar and glass 49-E as the matrix epoxy vinyl ester resin (DERAKANE 411-350). All laminates were formed each with four layers of reinforcements. Depending on the hybrid fabric, all the influencing factors mentioned above have been studied for laminates. All laminates were manufactured industrially used being the lamination process manual (hand-lay-up). All mechanical characterization and study of the mechanism of fracture (fracture mechanics) was developed for laminates subjected to uniaxial tensile test, bending in three and uniaxial compression. The analysis of fracture mechanisms were held involving the macroscopic, optical microscopy and scanning electron microscopy

Estudo de falha em placas laminadas usando métodos analíticos e numéricos

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia de Manutenção

Structure-property relationships in polymer nanocomposites

Tese de Doutoramento em Ciência e Engenharia de Polímeros e Compósitos

Optimization of magnetoelectric composites based on electroactive polymers for energy harvesting and sensor application

Tese de Doutoramento em Engenharia de Materiais.

Análise de pilares esbeltos de concreto armado confinados através do método dos elementos finitos

o confinamento é uma técnica que tem sido cada vez mais aplicada no reforço e reabilitação de peças comprimidas de concreto, com o objetivo de aumentar sua capacidade resistente e recuperá-las de eventuais deteriorações. Este trabalho apresenta um modelo não-linear fisico e geométrico, baseado no Método dos Elementos Finitos, para a análise de pilares esbeltos de concreto armado, sob estado triplo de tensões. Neste estudo, são utilizados elementos finitos isoparamétricos tridimensionais para o concreto e um modelo incorporado de armadura. O comportamento do concreto é descrito por um modelo elasto-viscoplástico, que permite a análise da estrutura sob cargas de curta e longa duração. Para representação do concreto ao longo do tempo, utiliza-se um modelo de camadas superpostas. A fissuração do concreto é representada através de um modelo de fissuras distribuídas, onde se considera a contribuição do concreto entre fissuras. É admitida aderência perfeita entre os materiais. O aço é modelado como um material elastoplástico perfeito ou com endurecimento linear, e os materiais utilizados para confinamento, como os compósitos de fibras de carbono, são modelados como um caso particular do modelo elastoplástico definido para o aço. O modelo não-linear geométrico foi desenvolvido com base na formulação Lagrangeana Total. Consideram-se grandes deslocamentos e pequenas deformações. Os resultados obtidos através do modelo computacional são cOnITontados com resultados experimentais disponíveis na literatura, de modo a validar o modelo matemático e a metodologia numérica. Boa correlação é obtida entre os resultados numéricos e experimentais, que confirmam estudos prévios realizados por diversos autores, na medida em que são verificados significativos ganhos de resistência e/ou ductilidade em pilares comprimidos de concreto, devido ao confinamento.

Viabilidade de utilização de um compósito a partir de resíduos para a construção de casas populares

Conselho Nacional de Desenvolvimento Científico e Tecnológico

Viabilidade de utilização de um compósito de matriz cerâmica com cargas recicláveis na fabricação de equipamentos solares

Composite materials can be defined as materials formed from two or more constituents with different compositions, structures and properties, which are separated by an interface. The main objective in producing composites is to combine different materials to produce a single device with superior properties to the component unit. The present study used a composite consisting of plaster, cement, EPS, tire, PET and water to build prototype solar attempt to reduce the manufacturing cost of such equipment. It was built two box type solar cookers, a cooler to be cooled by solar energy, a solar dryer and a solar cooker concentration. For these prototypes were discussed the processes of construction and assembly, determination of thermal and mechanical properties, and raising the performance of such solar systems. Were also determined the proportions of the constituents of the composite materials according to specific performance of each prototype designed. This compound proved to be feasible for the manufacture of such equipment, low cost and easy manufacturing and assembly processes

Desempenho de reatores anaeróbios horizontais com manta de lodo e de leito fixo, em série, tratando águas residuárias do beneficiamento do café por via úmida

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)