Improvement in the Reduction Behavior of Novel ZrO(2)-CeO(2) Solid Solutions with a Tubular Nanostructure by Incorporation of Pd

In this work, 1 wt % Pd/ZrO(2)-CeO(2) mixed oxide nanotubes with 90 mol % CeO(2) were synthesized following a very simple, high-yield procedure and their properties were characterized by synchrotron radiation X-ray diffraction, X-ray absorption near-edge spectroscopy (XANES), and scanning and high-resolution transmission electron microscopy (SEM and HRTEM). In situ XANES experiments were carried out under reducing conditions to investigate the reduction behavior of these novel nanotube materials. The Pd/CeO(2)-based nanotubes exhibited the cubic phase (Fm3m space group). The nanotube walls were composed of nanoparticles with an average crystallite size of about 7 nm, and the nanotubes exhibited a large specific surface area (85 m(2).g(-1)). SEM and HRTEM studies showed that individual nanotubes were composed of a curved sheet of these nanoparticles. Elemental analysis showed that the Ce:Zr:Pd ratios appeared to be approximately constant across space, suggesting compositional homogeneity in the samples. XANES results indicated that the extent of reduction of these materials is low and that the Ce(4+) state is in the majority over the reduced Ce(3+) state. The results suggest that Pd cations-most likely Pd(2+)-form a Pd-Ce-Zr oxide solid solution and that the Pd(2+) is stabilized against reduction in this phase. However, incorporation of the Pd (1 wt %) into the crystal lattice of the nanotubes also appeared to destabilize Ce(4+) against reduction to Ce(3+) and caused a significant increase in its reducibility.

Effect of the Y(2)O(3)-ZrO(2) support composition on nickel catalyst evaluated in dry reforming of methane

Nickel catalysts with a load of 5 wt.% Ni, supported on pure ZrO(2) and ZrO(2) stabilized with 4 mol%, 8 mol% and 12 mol% of Y(2)O(3), were prepared by the polymerization method. The samples were characterized by X-ray diffraction (XRD), temperature-programmed reduction with hydrogen (TPR-H(2)), specific surface area (BET) and electronic paramagnetic resonance (EPR) and tested as catalysts for carbon dioxide reforming of methane. The XRD patterns showed the presence of the oxide precursor (NiO) and the tetragonal phase of a Y(2)O(3)-ZrO(2) solid solution. According to the TPR-H(2) analysis, the reduction of various NiO species was influenced by the composition of the support. Catalytic tests were conducted at 800 degrees C for 6 h, and the composition of the gaseous products and the catalytic conversion rate depended on the composition of the Y(2)O(3)-ZrO(2) solid solution and its influence on the supported NiO species. A direct relation was observed between the variation in the support, the nickel species supported on it and the performance in the catalytic tests. (C) 2008 Elsevier B.V. All rights reserved.

Structural changes and dynamic behaviour of vanadium oxide-based catalysts for gas-phase selective oxidations

Selective oxidation is one of the simplest functionalization methods and essentially all monomers used in manufacturing artificial fibers and plastics are obtained by catalytic oxidation processes. Formally, oxidation is considered as an increase in the oxidation number of the carbon atoms, then reactions such as dehydrogenation, ammoxidation, cyclization or chlorination are all oxidation reactions. In this field, most of processes for the synthesis of important chemicals used vanadium oxide-based catalysts. These catalytic systems are used either in the form of multicomponent mixed oxides and oxysalts, e.g., in the oxidation of n-butane (V/P/O) and of benzene (supported V/Mo/O) to maleic anhydride, or in the form of supported metal oxide, e.g., in the manufacture of phthalic anhydride by o-xylene oxidation, of sulphuric acid by oxidation of SO2, in the reduction of NOx with ammonia and in the ammoxidation of alkyl aromatics. In addition, supported vanadia catalysts have also been investigated for the oxidative dehydrogenation of alkanes to olefins , oxidation of pentane to maleic anhydride and the selective oxidation of methanol to formaldehyde or methyl formate [1]. During my PhD I focused my work on two gas phase selective oxidation reactions. The work was done at the Department of Industrial Chemistry and Materials (University of Bologna) in collaboration with Polynt SpA. Polynt is a leader company in the development, production and marketing of catalysts for gas-phase oxidation. In particular, I studied the catalytic system for n-butane oxidation to maleic anhydride (fluid bed technology) and for o-xylene oxidation to phthalic anhydride. Both reactions are catalyzed by systems based on vanadium, but catalysts are completely different. Part A is dedicated to the study of V/P/O catalyst for n-butane selective oxidation, while in the Part B the results of an investigation on TiO2-supported V2O5, catalyst for o-xylene oxidation are showed. In Part A, a general introduction about the importance of maleic anhydride, its uses, the industrial processes and the catalytic system are reported. The reaction is the only industrial direct oxidation of paraffins to a chemical intermediate. It is produced by n-butane oxidation either using fixed bed and fluid bed technology; in both cases the catalyst is the vanadyl pyrophosphate (VPP). Notwithstanding the good performances, the yield value didn’t exceed 60% and the system is continuously studied to improve activity and selectivity. The main open problem is the understanding of the real active phase working under reaction conditions. Several articles deal with the role of different crystalline and/or amorphous vanadium/phosphorous (VPO) compounds. In all cases, bulk VPP is assumed to constitute the core of the active phase, while two different hypotheses have been formulated concerning the catalytic surface. In one case the development of surface amorphous layers that play a direct role in the reaction is described, in the second case specific planes of crystalline VPP are assumed to contribute to the reaction pattern, and the redox process occurs reversibly between VPP and VOPO4. Both hypotheses are supported also by in-situ characterization techniques, but the experiments were performed with different catalysts and probably under slightly different working conditions. Due to complexity of the system, these differences could be the cause of the contradictions present in literature. Supposing that a key role could be played by P/V ratio, I prepared, characterized and tested two samples with different P/V ratio. Transformation occurring on catalytic surfaces under different conditions of temperature and gas-phase composition were studied by means of in-situ Raman spectroscopy, trying to investigate the changes that VPP undergoes during reaction. The goal is to understand which kind of compound constituting the catalyst surface is the most active and selective for butane oxidation reaction, and also which features the catalyst should possess to ensure the development of this surface (e.g. catalyst composition). On the basis of results from this study, it could be possible to project a new catalyst more active and selective with respect to the present ones. In fact, the second topic investigated is the possibility to reproduce the surface active layer of VPP onto a support. In general, supportation is a way to improve mechanical features of the catalysts and to overcome problems such as possible development of local hot spot temperatures, which could cause a decrease of selectivity at high conversion, and high costs of catalyst. In literature it is possible to find different works dealing with the development of supported catalysts, but in general intrinsic characteristics of VPP are worsened due to the chemical interaction between active phase and support. Moreover all these works deal with the supportation of VPP; on the contrary, my work is an attempt to build-up a V/P/O active layer on the surface of a zirconia support by thermal treatment of a precursor obtained by impregnation of a V5+ salt and of H3PO4. In-situ Raman analysis during the thermal treatment, as well as reactivity tests are used to investigate the parameters that may influence the generation of the active phase. Part B is devoted to the study of o-xylene oxidation of phthalic anhydride; industrially, the reaction is carried out in gas-phase using as catalysts a supported system formed by V2O5 on TiO2. The V/Ti/O system is quite complex; different vanadium species could be present on the titania surface, as a function of the vanadium content and of the titania surface area: (i) V species which is chemically bound to the support via oxo bridges (isolated V in octahedral or tetrahedral coordination, depending on the hydration degree), (ii) a polymeric species spread over titania, and (iii) bulk vanadium oxide, either amorphous or crystalline. The different species could have different catalytic properties therefore changing the relative amount of V species can be a way to optimize the catalytic performances of the system. For this reason, samples containing increasing amount of vanadium were prepared and tested in the oxidation of o-xylene, with the aim of find a correlations between V/Ti/O catalytic activity and the amount of the different vanadium species. The second part deals with the role of a gas-phase promoter. Catalytic surface can change under working conditions; the high temperatures and a different gas-phase composition could have an effect also on the formation of different V species. Furthermore, in the industrial practice, the vanadium oxide-based catalysts need the addition of gas-phase promoters in the feed stream, that although do not have a direct role in the reaction stoichiometry, when present leads to considerable improvement of catalytic performance. Starting point of my investigation is the possibility that steam, a component always present in oxidation reactions environment, could cause changes in the nature of catalytic surface under reaction conditions. For this reason, the dynamic phenomena occurring at the surface of a 7wt% V2O5 on TiO2 catalyst in the presence of steam is investigated by means of Raman spectroscopy. Moreover a correlation between the amount of the different vanadium species and catalytic performances have been searched. Finally, the role of dopants has been studied. The industrial V/Ti/O system contains several dopants; the nature and the relative amount of promoters may vary depending on catalyst supplier and on the technology employed for the process, either a single-bed or a multi-layer catalytic fixed-bed. Promoters have a quite remarkable effect on both activity and selectivity to phthalic anhydride. Their role is crucial, and the proper control of the relative amount of each component is fundamental for the process performance. Furthermore, it can not be excluded that the same promoter may play different role depending on reaction conditions (T, composition of gas phase..). The reaction network of phthalic anhydride formation is very complex and includes several parallel and consecutive reactions; for this reason a proper understanding of the role of each dopant cannot be separated from the analysis of the reaction scheme. One of the most important promoters at industrial level, which is always present in the catalytic formulations is Cs. It is known that Cs plays an important role on selectivity to phthalic anhydride, but the reasons of this phenomenon are not really clear. Therefore the effect of Cs on the reaction scheme has been investigated at two different temperature with the aim of evidencing in which step of the reaction network this promoter plays its role.

Preferential oxidation of CO in excess of H2 on Pt/CeO2–Nb2O5 catalysts

A series of CeO2–Nb2O5 mixed oxides with different Nb content, as well as the pure oxides, have been synthesized by co-precipitation with excess urea. These materials have been used as supports for platinum catalysts, with [Pt(NH3)4](NO3)2 as precursor. Both supports and catalysts have been characterized by several techniques: N2 physisorption at 77 K, X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, UV–vis spectroscopy, scanning electron microscopy, transmission electron microscopy, temperature-programmed reduction and temperature-programmed desorption (CO and H2), and their catalytic behaviour has been determined in the PROX reaction, both with an ideal gas mixture (CO, O2 and H2) and in simulated reformate gas containing CO2 and H2O. Raman spectroscopy analysis has shown the likely substitution of some Ce4+ cations by Nb5+ to some extent in supports with low niobium contents. Moreover, the presence of Nb in the supports hinders their ability to adsorb CO and to oxidize it to CO2. However, an improvement of the catalytic activity for CO oxidation is obtained by adding Nb to the support, although the Pt/Nb2O5 catalyst shows very low activity. The best results are found with the Pt/0.7CeO2–0.3Nb2O5 catalyst, which shows a high CO conversion (85%) and a high yield (around 0.6) after a reduction treatment at 523 K. The effect of the presence of CO2 and H2O in the feed has also been determined.

Design of high quality doped CeO2 solid electrolytes with nanohetero structure

Doped ceria (CeO2) compounds are fluorite related oxides which show oxide ionic conductivity higher than yttria-stabilized zirconia in oxidizing atmosphere. As a consequence of this, a considerable interest has been shown in application of these materials for low (400-650 degrees C) temperature operation of solid oxide fuel cells (SOFCs). In this paper, our experimental data about the influence of microstructure at the atomic level on electrochemical properties were reviewed in order to develop high quality doped CeO2 electrolytes in fuel cell applications. Using this data in the present paper, our original idea for a design of nanodomain structure in doped CeO2 electrolytes was suggested. The nanosized powders and dense sintered bodies of M doped CeO2 (M:Sm,Gd,La,Y,Yb, and Dy) compounds were fabricated. Also nanostiructural features in these specimens were introduced for conclusion of relationship between electrolytic properties and domain structure in doped CeO2. It is essential that the electrolytic properties in doped CeO2 solid electrolytes reflect in changes of microstructure even down to the atomic scale. Accordingly, a combined approach of nanostructure fabrication, electrical measurement and structure characterization was required to develop superior quality doped CeO2 electrolytes in the fuel cells.

Morphologically Diverse Cerium Oxide Nanostructures and Nanofields for Multi functional applications.

The prospective impact of nanomaterials in science and technology has followed an increasing trend due to their unique chemical and physical properties compared to bulk. Significant advances in current technologies in areas such as clean energy production, electronics, medicine, and environment have fuelled major research and development efforts in nanotechnology around the world. This leads to the opportunity to use such nanostructured materials in novel applications and devices. Ceria, zirconia, alumina and titania are some of the major oxides which find vast applications as a nanomaterial on a wider side.

Mesoporous mixed Nb2O5-ZrO2 catalysts for dehydration of glucose into 5-hydroxymethylfurfural

Biomass is the world’s most important renewable carbon source, whose major component, carbohydrates, can be valorized by transformation into biofuels and high value-added chemicals. Among the latter, 5-hydroxymethylfurfural (HMF), obtained by C6 carbohydrates dehydration, is a versatile and key intermediate for the production of a large spectrum of biobased chemicals. Different catalytic systems have been evaluated for HMF production, mostly based on heterogeneous catalysis as alternative to the use of conventional mineral acids [1]. Moreover, niobium oxide has shown interesting properties as acid catalyst for dehydration of sugars [2-3]. On the other hand, the high surface area and large pore size of mesoporous solids make them suitable for many catalytic processes. In the present work, the dehydration of glucose to HMF has been evaluated by using different mesoporous mixed Nb2O5-ZrO2 in a biphasic water–Methyl Isobutyl Ketone (MIBK) solvent system to avoid the HMF degradation. Different experimental parameters, such as reaction temperature and time, as well as the addition of CaCl2 have been studied in order to maximize the HMF yield.N2 adsorption-desorption isotherms have corroborated the mesostructured character of catalysts, being all isotherms of Type IV according to the IUPAC classification. BET surface area decreases for catalysts with higher Zr content (Table 1). Likewise, pore volume and average pore diameter values diminish after Zr incorporation. Concerning the acid properties, a clear correlation between Nb and acidity can be observed, in such a way that total acidity, as deduced from NH3-TPD, decreases when the Zr content rises, and consequently the amount of Nb is reduced.These mesoporous Nb-Zr catalysts have been tested in the dehydration of glucose to HMF at 175 ºC under batch operation in aqueous solution, using MIBK as co-solvent. It can be observed that both glucose conversion and HMF yield increase with the Nb content, being maximum (90% and 36%, respectively) after 90 minutes for Nb2O5. This trend changes when CaCl2 is added to the reaction medium, improving the catalytic performance of mixed oxides and ZrO2, but Nb2O5 maintains similar results than without salt addition. This could be justified by the interaction between CaCl2 and Lewis acid sites, since zirconium oxide possesses a higher amount of this acid sites type.

Direct precipitation of lead zirconate titanate by the hydrothermal method

Direct precipitation of fine powders of lead zirconate titanate (PZT) in the complete range of solid solution, is investigated under hydrothermal conditions, starting from lead oxide and titania/zirconia mixed gels. The perovskite phase is formed in the temperature range of 165 – 340°C. Sequence of the hydrothermal reactions is studied by identifying the intermediate phases. The initial formation of PbO: TiO2 solid solution is followed by the reaction of the same with the remaining mixed gels giving rise to X-ray amorphous PZT phase. Further, through crystallite growth, the X-ray crystalline PZT is formed. This method can be extended for the preparation of PLZT powder as well. The resulting powders are sinterable to high density ceramics.

Atomic Layer Deposition and Photocatalytic Properties of Titanium Dioxide Thin Films

Photocatalytic TiO2 thin films can be highly useful in many environments and applications. They can be used as self-cleaning coatings on top of glass, tiles and steel to reduce the amount of fouling on these surfaces. Photocatalytic TiO2 surfaces have antimicrobial properties making them potentially useful in hospitals, bathrooms and many other places where microbes may cause problems. TiO2 photocatalysts can also be used to clean contaminated water and air. Photocatalytic oxidation and reduction reactions proceed on TiO2 surfaces under irradiation of UV light meaning that sunlight and even normal indoor lighting can be utilized. In order to improve the photocatalytic properties of TiO2 materials even further, various modification methods have been explored. Doping with elements such as nitrogen, sulfur and fluorine, and preparation of different kinds of composites are typical approaches that have been employed. Photocatalytic TiO2 nanotubes and other nanostructures are gaining interest as well. Atomic Layer Deposition (ALD) is a chemical gas phase thin film deposition method with strong roots in Finland. This unique modification of the common Chemical Vapor Deposition (CVD) method is based on alternate supply of precursor vapors to the substrate which forces the film growth reactions to proceed only on the surface in a highly controlled manner. ALD gives easy and accurate film thickness control, excellent large area uniformity and unparalleled conformality on complex shaped substrates. These characteristics have recently led to several breakthroughs in microelectronics, nanotechnology and many other areas. In this work, the utilization of ALD to prepare photocatalytic TiO2 thin films was studied in detail. Undoped as well as nitrogen, sulfur and fluorine doped TiO2 thin films were prepared and thoroughly characterized. ALD prepared undoped TiO2 films were shown to exhibit good photocatalytic activities. Of the studied dopants, sulfur and fluorine were identified as much better choices than nitrogen. Nanostructured TiO2 photocatalysts were prepared through template directed deposition on various complex shaped substrates by exploiting the good qualities of ALD. A clear enhancement in the photocatalytic activity was achieved with these nanostructures. Several new ALD processes were also developed in this work. TiO2 processes based on two new titanium precursors, Ti(OMe)4 and TiF4, were shown to exhibit saturative ALD-type of growth when water was used as the other precursor. In addition, TiS2 thin films were prepared for the first time by ALD using TiCl4 and H2S as precursors. Ti1-xNbxOy and Ti1-xTaxOy transparent conducting oxide films were prepared successfully by ALD and post-deposition annealing. Highly unusual, explosive crystallization behaviour occurred in these mixed oxides which resulted in anatase crystals with lateral dimensions over 1000 times the film thickness.

Segregation in the MgO–MgAl2O4 system processed from nitrate precursors

The occurrence of segregation and its influence on microstructural and phase evolution have been studied in MgO–MgAl2O4 powders synthesized by thermal decomposition of aqueous nitrate precursors. When the nitrate solutions of Mg and Al were spray-pyrolyzed on a substrate held at 673 or 573 K, homogeneous mixed oxides were produced. Spraying and drying the nitrate solutions at 473 K resulted in the formation of compositionally inhomogeneous, segregated oxide mixtures. It is suggested that segregation in the dried powders was caused by the difference in solubility of the individual nitrate salts in water which caused Mg-rich and Al-rich salts to precipitate during dehydration of the solutions. The occurrence of segregation in the powders sprayed at 473 K and not 573 or 673 K is ascribed to the sluggish rate at which the early stages of decomposition occurred during which the cations segregated. The phase evolution in segregated and segregation-free MgO–MgAl2O4 powders has been compared. The distinguishing feature of the segregated powders was the appearance of stoichiometric periclase grain dimensions in excess of 0.3 μm at temperatures as low as 973 K. By comparison, the segregation-free powders displayed broad diffraction peaks corresponding to fine-grained and nonstoichiometric periclase. The grain size was in the range 5–30 nm at temperatures up to 1173 K. The key to obtaining fine-grained periclase was the ability to synthesize (Mg Al)O solid solutions with the rock salt structure. In the temperature range 973–1173 K, spinel grain size varied from 5 to 40 nm irrespective of its composition and did not appear to be influenced by segregation.

La-Doped Ba2In2O5 Electrolyte: Pechini Synthesis, Microstructure, Electrical Conductivity, and Application for CO Gas Sensing

Dense (Ba1―xLax)2In2O5+x (BLIO) electrolytes with different compositions (x = 0.4, 0.5, 0.6) were fabricated using powders obtained by the Pechini method. The formation of BLIO powders was investigated by using X-ray diffraction and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy. The calcination temperature and time were optimized. The sintered (Ba1―xLax)2In2O5+x electrolytes showed a relative density greater than ∼97%, and the major phase of three electrolyte compositions was indexed as a cubic perovskite. The electrical conductivity of BLIO ceramics at elevated temperatures in air was measured by ac-impedance spectroscopy. The activation energies for conduction in BLIO were 102 kJ mol―1 between 473 and 666 K and 118 kJ mol―1 between 769 and 873 K, which are comparable to that for 8 mol % yttria-stabilized cubic zirconia. Mixed-potential gas sensors utilizing BLIO-based electrolytes exhibited good sensitivity to different CO concentrations from ∼100 to ∼500 ppm and excellent selectivity to methane at around 873 K.

Estudo da desativação térmica de catalisadores à base de óxidos mistos de cério e zircônio

Em termos ambientais, os catalisadores automotivos se destacam pelos resultados altamente significativos alcançados após seu uso obrigatório em veículos leves. No entanto, as condições térmicas em que eles operam podem levar a um processo de perda de atividade significativa, após certo tempo de operação. Dentro desse contexto, este trabalho estudou o efeito da temperatura na desativação térmica de catalisadores automotivo modelo. Foram preparados catalisadores baseados em óxido misto de cério e zircônio na proporção 50% em mol de cério e zircônio (CZ). A partir dele foram produzidos os catalisadores Pd-CZ e Pd-CZ-LaAl. O catalisador Pd-CZ foi produzido pela impregnação do CZ com Pd na concentração de 0,5% m/m de CZ. O catalisador Pd-CZ-LaAl foi produzido a partir de uma mistura física do Pd-CZ com o suporte LaAl (alumina dopada com La na concentração de 1,9 % m/m de Al2O3), seguida de calcinação a 500˚C. Foram realizados envelhecimentos a 900C e 1200C em mufla com atmosfera oxidante por 12 e 36h. Os catalisadores foram caracterizados por um conjunto de técnicas físico-químicas. Foram realizadas análises de fisissorção de N2 para a medição da área específica e o estudo da evolução do diâmetro e volume de poros das amostras novas e envelhecidas. Análises de difração de raios X (DRX) foram feitas de forma a acompanhar possíveis transições de fases após o envelhecimento das amostras. Foi realizada análise química para validar a composição das amostras e ensaios de análise térmica para o catalisador CZ visando identificar a temperatura onde ocorre o fenômeno de segregação de fases. Realizaram-se ensaios de redução a temperatura programada (RTP) visando quantificar o consumo de hidrogênio e associá-lo à evolução da redutibilidade das amostras após o envelhecimento térmico. Finalmente, a avaliação catalítica foi realizada com base nas reações de oxidação do CO e do propano e de redução do NO pelo CO, através da obtenção de curvas de lightoff. As análises de DRX mostraram que o envelhecimento a 900C ocasionou alterações de fases da alumina, mas não foi verificada segregação de fases no CZ. Já a 1200C observou-se a referida segregação de fases, que coincide com a drástica queda na área específica das amostras, em alguns casos observando-se o colapso das propriedades texturais do catalisador. As análises de RTP mostraram que, em determinadas condições, o envelhecimento térmico promove a redutibilidade do sistema CZ e a introdução de Pd torna o catalisador mais facilmente redutível o que é evidenciado pelo deslocamento dos picos de redução para temperaturas mais baixas em comparação ao CZ puro. Os testes catalíticos mostraram que a introdução do Pd é um fator fundamental para a conversão do propano. Os catalisadores contendo Pd também converteram melhor o CO. Para os catalisadores envelhecidos a 1200C, o único resultado positivo foi no caso do Pd-CZ-LaAl que apesar deste tratamento térmico, ainda converteu o CO, propano e NO. Desta forma o catalisador Pd-CZ-LaAl apresentou resultados mais satisfatórios e isto evidencia que a mistura com LaAl melhora o desempenho e a estabilidade térmica do catalisador em altas temperaturas (acima de 300C).

Produção de biodiesel pela rota heterogênea empregando catalisadores a base de Zn e Al

Nos últimos anos, a busca por fontes de energia renováveis e o desenvolvimento de novas tecnologias para a produção de biocombustíveis têm sido objeto de intensa investigação. O biodiesel é um combustível biodegradável, derivado de fontes renováveis e é obtido em escala industrial principalmente através da reação de transesterificação de óleos vegetais e/ou gorduras animais com metanol na presença de catalisadores homogêneos, como NaOH. Entretanto, a utilização de catalisadores heterogêneos tem sido sugerida por diversos autores, por apresentar vantagens como a eliminação dos problemas de separação e purificação dos produtos obtidos. No presente trabalho foi investigada a produção de biodiesel a partir da transesterificação do óleo de soja com metanol utilizando óxidos mistos de Zn e Al como catalisadores sólidos básicos. A influência das variáveis: temperatura, concentração de catalisador e relação molar metanol/óleo de soja na produção de biodiesel foi avaliada. Os catalisadores preparados apresentaram predominantemente sítios básicos e foram ativos frente à reação estudada, sendo os resultados mais promissores apresentados pelo óxido misto com relação molar Al/(Al+Zn)=0,50, obtido por tratamento térmico à 450C, que apresentou rendimentos em ésteres metílicos de até 98,5% sob condições específicas. A metodologia da superfície de resposta foi utilizada visando estabelecer as condições ótimas para maximizar o rendimento em ésteres metílicos, tendo sido encontradas a temperatura de 165oC e a concentração de catalisador de 5,8% m/m em relação massa de óleo, no caso da relação molar metanol/óleo de soja limitada em 15. Essa limitação teve como objetivo garantir um processo viável em escala comercial

Síntese e caracterização de TiO2 puro e modificado para aplicações ambientais

Fotocatalisadores baseados em nanopartículas de dióxido de titânio modificados fornecem soluções em potencial para a mineralização de poluentes orgânicos em meio aquoso. Agentes modificadores têm sido amplamente investigados com o objetivo de promover a fotoativação pela luz visível. Foram estudadas a nível fundamental até aqui, as modificações estruturais, texturais e óticas causadas pela introdução de silício e nitrogênio na rede da titânia. Titânias puras (TiO2) e modificadas nanoestruturadas, particularmente titânias modificadas com silício (TiO2-SiO2), com razões atômicas Si/Ti de 0,1, 0,2 e 0,3 foram sintetizadas pelo método sol-gel a partir da hidrólise ácida de isopropóxido de titânio(IV) e tetraetoxisilano. As metodolo-gias sintéticas desenvolvidas tentaram aderir aos princípios da Química Verde, dispensando o uso de atmosfera inerte e temperatura e pressão elevadas, o que foi alcançado utilizando-se, principalmente, a agitação ultrassônica. Titânias modificadas com silício e dopadas com ni-trogênio (TiO2-SiO2-N) foram obtidas a partir do pré-tratamento de TiO2-SiO2 a 500 C ao ar e então submetidas ao fluxo de amônia (NH3) a 600 C por 1-3 h e, após resfriamento, foram recozidas a 400 C ao ar. Amostras distintas foram caracterizadas, na forma de pó seco e após calcinação entre 400600 C, por difração de raios X, adsorção de nitrogênio, microscopia eletrônica de varredura e espectroscopia de refletância difusa no UV-Visível. As titânias pu-ras, obtidas principalmente variando-se a razão de hidrólise, foram cristalizadas na forma de anatásio como fase predominante até 600 C, além de traços de brookita presente até 500 C. O rutilo foi identificado a partir de 600 C como fase minoritária, embora apresentando tama-nhos de cristal significativamente maiores que os estimados para o cristal de anatásio. As titâ-nias modificadas com até 20% de silício apresentaram notável estabilidade térmica, evidenci-ada pela presença exclusiva de anatásio até 900 C. Foi também observado o aparecimento de macroporos com diâmetro médio em torno de 55 nm após calcinação a 400 C, diferentemente do que se observou nas amostras em geral. A introdução de baixo teor de silício assegurou às titânias calcinadas valores elevados de área específica, atribuído ao efeito de contenção acentuada na taxa de crescimento do cristal. As titânias modificadas com silício e as titânias puras obtidas com taxa de hidrólise 25:1 para a razão H2O : Ti apresentaram mesoporos com diâmetros médios de mesma dimensão do cristal. As titânias modificadas com silício e dopa-das com nitrogênio apresentaram absorção na região visível entre 400-480 nm, com discreta redução da energia de band gap para as transições eletrônicas consideradas. Titânias calcina-das a 300−400 C apresentaram desempenho fotocatalítico semelhante ao TiO2 P25 da De-gussa sob irradiação UV, na degradação do azo corante Reactive Yellow 145 em soluções a-quosas em pH 5 a 20 1C

Avaliação de aditivos para remoção catalítica de SOx em unidades de fcc

Os óxidos de enxofre (SOx) são um dos maiores poluentes atmosféricos e um dos precursores da chuva ácida. Um levantamento feito na Petrobrás mostrou que cerca de 17% dos SOx emitidos numa refinaria são oriundos do processo de FCC. Com o avanço dos controles ambientais, traduzido numa legislação mais restritiva, a técnica de incorporação de aditivos para remoção de SOx em UFCCs apresenta-se como a alternativa de menor custo frente outras tecnologias de abate das emissões de SOx. No presente trabalho, foram estudados aditivos constituídos por compostos derivados de hidrotalcitas com a substituição parcial do magnésio e do alumínio por cobre e/ou manganês, sendo estes impregnados ou não por dióxido de cério. Estes aditivos foram submetidos a testes de desempenho em uma unidade multi-propósito acoplada a um micro-GC/TCD. Em todos os testes, a corrente gasosa para a etapa de adsorção oxidativa foi de 1700 ppm de SO2 e 1,5% O2 em He e, para a etapa de regeneração, 30% H2/He. No primeiro conjunto de testes, realizou-se uma adsorção a 720C de 10 min e regeneração com um patamar a 530C, seguido de um TPR até 800C. Observou-se que as amostras impregnadas com cério apresentaram o melhor desempenho na remoção de SO2, indicando que o cério pode ter um papel de promotor da oxidação de SO2 a SO3. Os resultados do TPR mostram que as amostras com cério e com manganês parecem apresentar menores temperaturas de redução dos sulfatos, apesar das maiores liberações de H2S serem identificadas nas amostras com cobre. No segundo conjunto de testes, a adsorção foi a 720C durante 35 min e a regeneração a 650C por 5 minutos em um patamar de 5 minutos, seguida de um TPR até 800C. Para os tempos de sulfatação curtos (5 e 10 min), os resultados confirmaram o efeito positivo que a incorporação de CeO2 apresenta sobre a adsorção oxidativa do SO2. Todavia, para tempos de reação maiores (35 min), não se observou uma correlação clara entre a composição química do catalisador e a quantidade total de SOx removida. Os aditivos foram ainda testados em ciclos de reação-regeneração em condições equivalentes ao segundo conjunto de testes descrito. De um modo geral, os aditivos que contêm cobre têm uma vida útil superior aos demais, possivelmente, pelo fato do cobre ter importante papel na regeneração do aditivo