Mineralogy and diagenesis: Their effect on acoustic and electrical properties of pelagic clays at DSDP Leg 86 Holes

Analysis of pelagic clay samples from Sites 576, 578, and 581 shows that physical, acoustic, and electrical trends with increasing burial depth are related to mineralogical and diagenetic changes. The properties of interest are bulk density (roo), porosity (phi), compressional-wave velocity (Vp) and velocity anisotropy (Ap), and electrical resistivity (Ro) and resistivity anisotropy (Ar). In general, as demonstrated in particular for the brown pelagic clay, the increase in roo, Vp, Ro, and to a lesser extent Ap and Ar with increasing depth is primarily caused by decreasing phi (and water content) as a result of compaction. The mineralogy and chemistry of the pelagic clays vary as a function of burial depth at all three sites. These variations are interpreted to reflect changes in the relative importance of detrital and diagenetic components. Mineralogical and chemical variations, however, play minor roles in determining variations in acoustic and electrical properties of the clays with increasing burial depth.

Real time power plant simulation platform for training on Electrical Protections and Automatic Voltage Regulators

Electrical Protection systems and Automatic Voltage Regulators (AVR) are essential components of actual power plants. Its installation and setting is performed during the commissioning, and it needs extensive experience since any failure in this process or in the setting, may entails some risk not only for the generator of the power plant, but also for the reliability of the power grid. In this paper, a real time power plant simulation platform is presented as a tool for improving the training and learning process on electrical protections and automatic voltage regulators. The activities of the commissioning procedure which can be practiced are described, and the applicability of this tool for improving the comprehension of this important part of the power plants is discussed. A commercial AVR and a multifunction protective relay have been tested with satisfactory results.

Paper-like electronic displays: Large-area rubber-stamped plastic sheets of electronics and microencapsulated electrophoretic inks

Electronic systems that use rugged lightweight plastics potentially offer attractive characteristics (low-cost processing, mechanical flexibility, large area coverage, etc.) that are not easily achieved with established silicon technologies. This paper summarizes work that demonstrates many of these characteristics in a realistic system: organic active matrix backplane circuits (256 transistors) for large (≈5 × 5-inch) mechanically flexible sheets of electronic paper, an emerging type of display. The success of this effort relies on new or improved processing techniques and materials for plastic electronics, including methods for (i) rubber stamping (microcontact printing) high-resolution (≈1 μm) circuits with low levels of defects and good registration over large areas, (ii) achieving low leakage with thin dielectrics deposited onto surfaces with relief, (iii) constructing high-performance organic transistors with bottom contact geometries, (iv) encapsulating these transistors, (v) depositing, in a repeatable way, organic semiconductors with uniform electrical characteristics over large areas, and (vi) low-temperature (≈100°C) annealing to increase the on/off ratios of the transistors and to improve the uniformity of their characteristics. The sophistication and flexibility of the patterning procedures, high level of integration on plastic substrates, large area coverage, and good performance of the transistors are all important features of this work. We successfully integrate these circuits with microencapsulated electrophoretic “inks” to form sheets of electronic paper.

Students at University of Michigan do research in the electrical engineering laboratory in the College of Engineering

Shown recording data are, left to right, John P. Vajda, Milwaukee WI, and James A. Lovell, Grand Rapids, MI. graduate students in electrical engineering.

Electrical Engineering Laboratory

l-r John P. Vajda, James A. Lovell grad students

Tomb, excavated artifact, Rabbits, Birds, Bamboo and Flowers, center portion: birds and flowers; from the western interior wall of the outer (xiaozhang) coffin

Liaoning. Faku. Yemaotai; hanging scroll, ink and colors on silk

Review of international geothermal activities and assessment of U.S. industry opportunities /

"LA-11066-MS ... UC-66."

Proceedings of the NMFS/EDS Workshop on Climate and Fisheries, April 26-29, 1976 : meetings held at the Center for Climatic and Environmental Assessment, Columbia, Mo.

"October 1976."

Thermal conductivity and electrical resistivity : standard reference materials--tungsten SRM's 730 and 799, from 4 to 3000K /

Includes bibliographical references.

Manpower resources in chemistry and chemical engineering

Mode of access: Internet.

Electrical engineering;

Mode of access: Internet.

Proceedings of 1st Ad-Hoc Forum of Scientific and Technical Information Analysis Center Managers, Directors, and Professional Analysts, held at Battelle Memorial Institute, Columbus, Ohio, November 9-11, 1965 /

"Conf-651131, General, miscellaneous, and progress reports (TID-4500)."

Goddard '66; a year in review at Goddard Space Flight Center, National Aeronautics and Space Administration.

Cover title.

Mechanics' pocket memoranda; a convenient pocketbook for all persons interested in mechanical engineering, steam engineering, electrical engineering, railroad engineering, hydraulic engineering, bridge engineering, etc.,

Mode of access: Internet.