Pollinators of an endemic and endangered species, Mammillaria gaumeri (Cactaceae), in its natural habitat (coastal dune) and in a botanical garden.

Mammillaria gaumeri (Britton & Ross) Orcutt (Cactaceae), an endemic plant of the Yucatan Peninsula, is included by the Mexican government in the list of species that require special protection. Its natural habitat is now restricted to fragmented areas and protection programs involve botanical gardens in growing individuals rescued from disturbed areas. Little information is available on the reproductive characteristics of this species and nothing is known of its pollinators. We investigated the visitors of M. gaumeri flowers, collecting and observing bee species in its natural habitat (i.e., coastal dune) and in a botanical garden, where coastal dune vegetation had been created. Observations were made on plants whose density was artificially increased by grouping flowering individuals. At each site, we: 1) collected insects visiting the flowers; 2) recorded number of visits; and 3) video-recorded bee movements on the flowers. As expected, the number of bee species and visitation frequency were higher at the botanical garden than at the coastal dune. After landing on a flower, bees either inspected the anthers or dived among them. These behaviors, carried out by all observed species, seemed related to the state of the anthers (full or empty of pollen) and stigma lobes (opened or closed). Specifically, visits lasted longer when anthers were full of pollen and stigma lobes were opened. The same bee species recorded on the dune were also recorded at the botanical garden, suggesting that the artificial dune at the botanical garden offered suitable conditions for the natural pollinators of this endangered cactus.

Comparison of serum and whole-blood specimens for the detection of Candida DNA in critically ill, non-neutropenic patients

In contrast to the multitude of studies on fungal PCR assay methods, little work has been reported evaluating Candida PCR performance when using whole blood compared with serum in candidaemic patients. Here, a comparison of the performance of whole-blood and serum specimens using a set of real-time PCR Candida species assays is described. Specimens were collected prospectively from non-neutropenic adults who were recruited to a diagnostic clinical trial, the primary purpose of which was to verify the performance of the assays using serum; in all, 104 participants also had whole-blood specimens submitted for analysis in addition to the serum specimen. Of these participants, 10 had laboratory-confirmed candidaemia and 94 were categorized as being 'unlikely' to have invasive Candida infection. PCR results from the whole-blood specimens are presented here and compared with the results from serum specimens in this subgroup among whom both specimen types were obtained contemporaneously. All participants with candidaemia were PCR-positive from serum samples; however, only seven were PCR-positive from whole blood. All specimens from patients in the 'unlikely' category were PCR-negative in both types of specimen. Moreover, DNA extraction from serum required 1 h; extraction from whole blood required approximately 3 h. These data tentatively suggest that, overall, serum is an appropriate specimen for Candida PCR for detection of candidaemia in non-neutropenic adults.

The Behavior of compressively loaded stiffener runout specimens - Part II: Finite element analysis

The termination of stiffeners in composite aircraft structures give rise to regions of high interlaminar shear and peel stresses as the load in the stiffener is diffused into the skin. This is of particular concern in co-cured composite stiffened structures where there is a relatively low resistance to through-thickness stress components at the skin-stiffener interface. In Part I, experimental results of tested specimens highlighted the influence of local design parameters on their structural response. Indeed some of the observed behavior was unexpected. There is a need to be able to analyse a range of changes in geometry rapidly to allow the analysis to form an integral part of the structural design process.

This work presents the development of a finite element methodology for modelling the failure process of these critical regions. An efficient thick shell element formulation is presented and this element is used in conjuction with the Virtual Crack Closure Technique (VCCT) to predict the crack growth characteristics of the modelled specimens. Three specimens were modelled and the qualitative aspects of crack growth were captured successfully. The shortcomings in the quantitative correlation between the predicted and observed failure loads are discussed. There was evidence to suggest that high through-thickness compressive stresses enhanced the fracture toughness in these critical regions.