Comparison of algorithms for loss allocation in transmission networks considering power redispatch

An analysis of the performances of three important methods for generators and loads loss allocation is presented. The discussed methods are: based on pro-rata technique; based on the incremental technique; and based on matrices of circuit. The algorithms are tested considering different generation conditions, using a known electric power system: IEEE 14 bus. Presented and discussed results verify: the location and the magnitude of generators and loads; the possibility to have agents well or poorly located in each network configuration; the discriminatory behavior considering variations in the power flow in the transmission lines. © 2004 IEEE.

Hybrid three-phase HPF rectifier with programmable input current THD, using FPGA device and VHDL language

In this paper is proposed and analyzed a digital hysteresis modulation using a FPGA (Field Programmable Gate Array) device and VHDL (Hardware Description Language), applied at a hybrid three-phase rectifier with almost unitary input power factor, composed by parallel SEPIC controlled single-phase rectifiers connected to each leg of a standard 6-pulses uncontrolled diode rectifier. The digital control allows a programmable THD (Total Harmonic Distortion) at the input currents, and it makes possible that the power rating of the switching-mode converters, connected in parallel, can be a small fraction of the total average output power, in order to obtain a compact converter, reduced input current THD and almost unitary input power factor. Finally, the proposed digital control, using a FPGA device and VHDL, offers an important flexibility for the associated control technique, in order to obtain a programmable PFC (Power Factor Correction) hybrid three-phase rectifier, in agreement with the international standards (IEC, and IEEE), which impose limits for the THD of the AC (Alternate Current) line input currents. The proposed strategy is verified by experiments. © 2008 IEEE.

Technology assessment for power quality mitigation devices - Micro-DVR case study

This work presents a case study on technology assessment for power quality devices. A system compatibility test protocol for power quality mitigation devices was developed in order to evaluate the functionality of three-phase voltage restoration devices. In order to case test this test protocol, a development platform with reduced power for DVR (Dynamic Voltage Restorer), the Micro-DVR, was tested, and results were discussed based on voltage disturbances standards. ©2008 IEEE.

Análise de integridade de sinal e crosstalk em placa de circuito impresso

Pós-graduação em Engenharia Elétrica - FEIS

Isolamento passivo de vibrações aleatórias atuantes sobre equipamentos eletrônicos aeronaúticos embarcados

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Associação de agentes patogênicos isolados em análise microbiológica da água, com a presença de mastite clínica ou subclínica, em propriedades leiteiras da região de Cerqueira César-SP

Pós-graduação em Medicina Veterinária - FMVZ

Sistema especialista para automação do processo de aeração de grãos de milho em pequenas propriedades

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento e avaliação de equipamentos e metodologia para determinação de parâmetros físicos do solo relacionados a dias trabalháveis com máquinas agrícolas

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

NodePM: A Remote Monitoring Alert System for Energy Consumption Using Probabilistic Techniques

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Análise experimental de um trocador de calor por mudança de fase e desenvolvimento de um modelo numérico simplificado

Pós-graduação em Engenharia Mecânica - FEIS

Diagnóstico da gestão e do gerenciamento dos resíduos eletroeletrônicos gerados no campus da Faculdade de Engenharia de Guaratinguetá/Unesp

Currently, in Brazil, the quantity and quality of new types of wastes, discarded without criteria in urban areas, has been responsible for considerable impacts on public health and the environment. According to a report prepared by the Institute of Applied Economic Research (IPEA), the country loses about U.S. $ 8 billion annually, due lack of waste recycling, which go directly into landfills or dumps. Among these solid wastes are waste electrical and electronic equipment (WEEE), whose characteristics are complex, by having in its composition substances of high value-added and other health hazards which require different treatment of household waste. Aiming to fill the gap in Brazilian environmental legislation, on 02/08/2010, was sanctioned the National Policy Solid Waste (Law No. 12,305), already regulated on 23/12/2010 (Decree No 7404), whose based on the following principles:reduction of waste generation and toxicity of shared responsibility, proper planning management, social inclusion of waste pickers and sustainable production and consumption. Given the above, this work presented here, aims generally present a diagnosis of the current situation of electronic waste generated in the Faculty of Engineering, Campus Guaratinguetá, FEG / UNESP, to provide data for management and management of these waste, based on sustainability, the economic losses and minimizing environmental impacts and public health related to the flow and the improper disposal of these wastes

Exigências ambientais europeias: novos desafios competitivos para o complexo eletrônico brasileiro

The objective of this paper is to evaluate the implications of the european environmental requirements for electronic equipment on brazilian electronic industry sector. These deter-minations deal with elimination of hazardous substances and management of electronic products waste and have reached not only the electronic sector companies in international level, but brazilian electronic sector as well. Most brazilian companies of the electronic sector are getting complied with the requirement that restricts the use of hazardous substances. The main consequences of this process are technological innovations and changes on contractual relationships among companies. Foreign companies branches are more advanced than local ones in terms of timing of compliance to the new requirements and technological perfor-mance, showing an alignment with headquarter strategies. Not being complied with these requirements avoid companies to achieve commercial benefits and open space for questions about policies Brazil must take.

Anelastic behavior due to interstitial oxygen in SmBa(2)Cu(3)O7-delta

The composite SmBa2Cu3O7-delta (Sm-123), obtained by the substitution of the ion Y for Sm in the very well known and studied YBa2Cu3O7-delta (Y-123), is potentially attractive for better understanding superconductivity mechanisms and for its applications as electronic devices. Sm-123 samples show higher critical temperatures than Y-123 ones do and a larger solubility of Sm in Ba-Cu-O solvent, which makes their growth process faster. When oxygen is present interstitially, it strongly affects the physical properties of the material. The dynamics of oxygen can be investigated by anelastic spectroscopy measurements, a powerful technique for the precise determination of the oscillation frequency and the internal friction when atomic jumps are possible. Anelastic spectroscopy allows determining the elasticity modulus (related to the oscillation frequency) and the elastic energy loss (related to the internal friction) as a function of the temperature. The sample was also investigated by X-ray diffraction (XRD), scanning electronic microscopy (SEM), and electric resistivity. The results obtained show a thermally activated relaxation structure composed by at least 3 relaxation processes. These processes may be attributed to the jumps of oxygen atoms present of the Cu-O plane in the orthorhombic phase.

Metodologia de simulação numérica do comportamento térmico em equipamentos eletroeletrônicos

Pós-graduação em Engenharia Elétrica - FEIS

Contribuições para a melhoria da gestão de resíduos de eletroeletrônicos no Brasil, no contexto da sustentabilidade ambiental

Pós-graduação em Engenharia de Produção - FEG