AlN-based BAW resonators with CNT electrodes for gravimetric biosensing

Solidly mounted resonators (SMRs) with a top carbon nanotubes (CNTs) surface coating that doubles as an electrode and as a sensing layer have been fabricated. The influence of the CNTs on the frequency response of the resonators was studied by direct comparison to identical devices with a top metallic electrode. It was found that the CNTs introduced significantly less mass load on the resonators and these devices exhibited a greater quality factor, Q (>2000, compared to ∼1000 for devices with metal electrodes), which increases the gravimetric sensitivity of the devices by allowing the tracking of smaller frequency shifts. Protein solutions with different concentrations were loaded on the top of the resonators and their responses to mass-load from physically adsorbed coatings were investigated. Results show that resonators using CNTs as the top electrode exhibited a higher frequency change for a given load (∼0.25 MHz cm2 ng−1) compared to that of a metal thin film electrode (∼0.14 MHz cm2 ng−1), due to the lower mass of the CNTelectrodes and their higher active surface area compared to that of a thin film metal electrode. It is therefore concluded that the use of CNTelectrodes on resonators for their use as gravimetric biosensors is a significant improvement over metallic electrodes that are normally employed.

La absorción acústica a ruido de impacto en placas de aislamiento térmico de suelo radiante

Actualmente en el mercado existen una reducida variedad de materiales específicos de ruido de impactos. Los materiales que han de ser utilizados como material resiliente, han de cumplir unos valores muy bajos del módulo de elasticidad E. Mientras el valor del caucho blando está en el orden de los 100 kg/cm2, el valor del acero es de 2.100.000 kg/cm2 (21.000 veces mayor). Estos valores tan bajos hacen que diferencias de apenas 50 kg/cm2 produzcan variaciones muy importantes en las ganancias de aislamiento acústico. La realización de los ensayos de caracterización acústica a ruido de impacto en laboratorio es un proceso largo y caro. En primer lugar se necesita elaborar un forjado de referencia, que ha de ser ensayado de forma independiente. Con posterioridad, se ha de colocar la losa flotante, y volver a realizar la prueba. Con la diferencia de las medidas realizadas, se determinan los valores de módulo de elasticidad. Como alternativa a este método, en la ponencia del congreso “TECNIACÚSTICA GANDÍA 2006” sobre “estudio de cinco métodos para determinar las propiedades dinámicas de capas elásticas para la mejora del aislamiento a ruido de impactos”, presentada por Francisco Simón, David K. Anthony, Mª José Fernández, proponen un total de cinco alternativas al ensayo indicado en la norma. Al margen de las condiciones acústicas, las placas de suelo radiante necesitan garantizar unos valores mínimos de aislamiento térmico. Con las actuales necesidades normativas, la solución habitual consiste en la superposición de dos materiales: en primer lugar, inmediatamente sobre el forjado, se coloca el material encargado de proporcionar el aislamiento acústico, generalmente una lámina flexible de polietileno. Encima de ella se coloca la placa de aislamiento térmico, generalmente una plancha de poliestireno expandido con resaltes en las que se encajan las tuberías que conducen el agua calefactada. El poliestireno expandido convencional, no tiene unos valores de módulo elástico suficientemente bajo para poder actuar como material resiliente. Para conseguir estos valores, es necesario elastificar el material mediante su introducción en una prensa (Poliestireno expandido elastificado EEPS). La utilización de esta técnica es incompatible con el proceso de fabricación de planchas moldeadas con tetones para la integración de los soportes de las tuberías. La lámina flexible de polietileno, si tienes valores aceptables, tanto de aislamiento térmico como acústico, en cambio no es posible la integración de los tetones durante su proceso de fabricación para soportar las canalizaciones de agua. El objetivo de la investigación consiste en integrar en una única placa las características tanto térmicas como acústicas necesarias para satisfacer todas las necesidades. Como se ha indicado más arriba, los materiales resilientes han de cumplir unos valores muy bajos del módulo de elasticidad E. Mientras el valor del caucho blando está en el orden de los 100 kg/cm2, el valor del acero es de 2.100.000 kg/cm2 (21.000 veces mayor). Pero no es menos cierto que con acero, dando la forma adecuada (un helicoide) se consigue un elemento muy elástico, un muelle. Tal es así, que variando la forma se puede conseguir el módulo de elásticidad E deseado, resultando utilidades tan dispares como el resorte de un bolígrafo o la suspensión de un coche. Por otro lado, y como se ha indicado anteriormente, la determinación de los valores mecánicos de los materiales aislantes térmicos es cara y complicada. Como objetivo secundario de la investigación, se establece el proponer un ensayo alternativo, más rápido y económico que el propuesto por la norma para facilitar el estudio de nuevas alternativas, sin tener que hacer grandes desembolsos económicos en

Adaptación de una central térmica de carbón a la Directiva de Emisiones Industriales

El proyecto que se presenta a continuación recoge la adaptación de una Central Térmica de carbón al cumplimiento de la DIRECTIVA 2010/75/UE DEL PARLAMENTO EUROPEO Y DEL CONSEJO de 24 de noviembre de 2010 sobre las emisiones industriales. La Central sobre la que se realiza el proyecto tiene un grupo térmico de carbón suscritico refrigerado por agua, con una potencia a plena carga de 350 MWe y de 190 MWe a mínimo técnico. Genera 1 090 t/h de vapor a 540 °C y 168 kg/cm2 funcionando a plena carga. Actualmente las emisiones de NOx son de 650 mg/m3, (condiciones normales, seco, 6 % O2). El objeto del proyecto es reducir estas emisiones a un valor máximo de 200 mg/m3 en las mismas condiciones. El proyecto analiza detalladamente las condiciones actuales de operación de la instalación en cuanto a combustible utilizado, horas de funcionamiento, condiciones climáticas y producción. Se analiza así mismo, todas las técnicas disponibles en mercado para la reducción del NOx, diferenciando entre medidas primarias (actúan sobre los efectos de formación) y secundarias (limpieza de gases). Las medidas primarias ya están implementadas en la central, por tanto, el proyecto plantea la reducción con medidas secundarias. De las medidas secundarias analizadas se ha seleccionado la instalación de un Reactor de Reducción Selectiva Catalítica (Reactor SCR). Tras un análisis de los diferentes reactores y catalizadores disponibles se ha seleccionado un reactor de configuración High-dust, una disposición de catalizador en 3 capas más 1, cuyos componentes están basados en óxidos metálicos (TiO2, V2O5, WO3) y estructura laminar. Se ha buscado la instalación del reactor para operar a una temperatura inferior a 450 °C. Como agente reductor se ha seleccionado NH3 a una dilución del 24,5 %. El proyecto recoge también el diseño de todo el sistema de almacenamiento, evaporación, dilución e inyección de amoniaco. El resultado del proyecto garantiza una concentración en los gases de salida por la chimenea inferior 180 mg/m3(n) de NOx. La reducción del NOx a los límites establecidos, tienen un coste por MWh neto generado para la central, trabajando 60 % a plena carga y 40 % a mínimo técnico y una amortización de 10 años, de 4,10 €/MWh. ABSTRACT The following project shows the compliance adjustment of a coal-fired power station to the 2010/75/EU Directive of the European Parliament and Council 24th November 2010 on industrial emissions. The project is based on a power station with a subcritical thermal coal unit, cooled with water, with a maximum power of 350 MWe and a technical minimum of 190 MWe. It produces 1 090 t/h of steam at 540 ° C and 168 kg/cm2 operating under full load. Currently, NOx emissions are 650 mg / m3 (normal conditions, dry, 6% O2). The project aims to reduce these emissions to a maximum value of 200 mg / m3 under the same conditions. The project analyses in detail the current operating conditions of the system in terms of fuel used, hours of operation, climatic conditions and production. In addition, it also analyses every available technique of NOx reduction on the market, distinguishing between primary (acting on the effects of formation) and secondary measures (gas cleaning). Primary measures are already implemented in the plant, thus proposing reduction with secondary measures. Among the secondary measures analyzed, it has been selected to install a Selective Catalytic Reduction Reactor (SCR Reactor). Having researched the different reactors and catalysts available, for the reactor has been selected High-dust configuration, an arrangement of catalyst in 3 layers plus 1, whose components are based on metal oxides (TiO2, V2O5, WO3) and laminar structure. The reactor has been sought facility to operate at a temperature below 450 ° C. NH3 diluted to 24,5 % has been selected as reducing agent. The project also includes the design of the entire storage system, evaporation, dilution and ammonia injection. The results of the project ensure a gas concentration in the lower chimney exit below 180 mg / m3(n) NOx. The reduction of NOx to the established limits has a cost per net MWh generated in the plant, working at 60% of full load and at 40% of technical minimum, with an amortization of 10 years, 4,10 € / MWh.

Efectos de un programa de entrenamiento mediante electroestimulación de cuerpo completo en la composición corporal en dos mujeres

Introducción: El sobrepeso y la obesidad son definidos como una acumulación anormal o excesiva de grasa que puede ser perjudicial para la salud. Ambas están asociadas al padecimiento de un gran número de patologías como hipercolesterolemia, enfermedades cardiovasculares, problemas respiratorios o enfermedades musculo esquelética. Objetivos: Analizar los efectos de dos entrenamientos de electroestimulación de cuerpo completo, de 20 Hz y 85 Hz y dieta isocalórica durante 4 semanas, sobre la composición corporal en dos mujeres para observar cuál de ellos es más efectivo tanto para la pérdida de grasa corporal como para la ganancia de masa muscular. Material y métodos: Participaron dos mujeres sedentarias (Participante 1, programa de 85 Hz: Edad = 30 años, IMC = 33,0 kg/cm2 y porcentaje de grasa = 46,6; participante 2, programa de 20 Hz: Edad = 19 años, IMC= 23,9 kg/cm2 y porcentaje de grasa = 33,2) y sin experiencia en el entrenamiento de fuerza.

Regulation of the phosphorylation of the dopamine- and cAMP-regulated phosphoprotein of 32 kDa in vivo by dopamine D1, dopamine D2, and adenosine A2A receptors

Dopamine D1, dopamine D2, and adenosine A2A receptors are highly expressed in striatal medium-sized spiny neurons. We have examined, in vivo, the influence of these receptors on the state of phosphorylation of the dopamine- and cAMP-regulated phosphoprotein of 32 kDa (DARPP-32). DARPP-32 is a potent endogenous inhibitor of protein phosphatase-1, which plays an obligatory role in dopaminergic transmission. A dose-dependent increase in the state of phosphorylation of DARPP-32 occurred in mouse striatum after systemic administration of the D2 receptor antagonist eticlopride (0.1–2.0 mg/kg). This effect was abolished in mice in which the gene coding for the adenosine A2A receptor was disrupted by homologous recombination. A reduction was also observed in mice that had been pretreated with the selective A2A receptor antagonist SCH 58261 (10 mg/kg). The eticlopride-induced increase in DARPP-32 phosphorylation was also decreased by pretreatment with the D1 receptor antagonist SCH 23390 (0.125 and 0.25 mg/kg) and completely reversed by combined pretreatment with SCH 23390 (0.25 mg/kg) plus SCH 58261 (10 mg/kg). SCH 23390, but not SCH 58261, abolished the increase in DARPP-32 caused by cocaine (15 mg/kg). The results indicate that, in vivo, the state of phosphorylation of DARPP-32 and, by implication, the activity of protein phosphatase-1 are regulated by tonic activation of D1, D2, and A2A receptors. The results also underscore the fact that the adenosine system plays a role in the generation of responses to dopamine D2 antagonists in vivo.

High-pressure adsorption of supercritical gases on activated carbons: An improved approach based on the density functional theory and the bender equation of state

Adsorption of nitrogen, argon, methane, and carbon dioxide on activated carbon Norit R1 over a wide range of pressure (up to 50 MPa) at temperatures from 298 to 343 K (supercritical conditions) is analyzed by means of the density functional theory modified by incorporating the Bender equation of state, which describes the bulk phase properties with very high accuracy. It has allowed us to precisely describe the experimental data of carbon dioxide adsorption slightly above and below its critical temperatures. The pore size distribution (PSD) obtained with supercritical gases at ambient temperatures compares reasonably well with the PSD obtained with subcritical nitrogen at 77 K. Our approach does not require the skeletal density of activated carbon from helium adsorption measurements to calculate excess adsorption. Instead, this density is treated as a fitting parameter, and in all cases its values are found to fall into a very narrow range close to 2000 kg/m(3). It was shown that in the case of high-pressure adsorption of supercritical gases the PSD could be reliably obtained for the range of pore width between 0.6 and 3 run. All wider pores can be reliably characterized only in terms of surface area as their corresponding excess local isotherms are the same over a practical range of pressure.

Physical properties and sedimentology of 4 profiles fom the South Atlantic

Ultrasonic P wavc transmission seismograms recorded on sediment cores have been analyzed to study the acoustic and estimate the clastic properties of marine sediments from different provinces dominated by terrigenous, calcareous, amI diatomaceous sedimentation. Instantaneous frequencies computed from the transmission seismograms are displayed as gray-shaded images to give an acoustic overview of the lithology of each core. Ccntirneter-scale variations in the ultrasonic waveforms associated with lithological changes are illustrated by wiggle traces in detail. Cross-correlation, multiple-filter, and spectral ratio techniques are applied to derive P wave velocities and attenuation coefficients. S wave velocities and attenuation coefficients, elastic moduli, and permeabilities are calculated by an inversion scheme based on the Biot-Stoll viscoelastic model. Together wilh porosity measurements, P and S wave scatter diagrams are constructed to characterize different sediment types by their velocity- and attenuation-porosity relationships. They demonstrate that terrigenous, calcareous, and diatomaceous sediments cover different velocity- and attenuation-porosity ranges. In terrigcnous sediments, P wave vclocities and attenuation coefficients decrease rapidly with increasing porosity, whereas S wave velocities and shear moduli are very low. Calcareous sediments behave similarly at relatively higher porosities. Foraminifera skeletons in compositions of terrigenous mud and calcareous ooze cause a stiffening of the frame accompanied by higher shear moduli, P wave velocities, and attenuation coefficients. In diatomaceous ooze the contribution of the shear modulus becomes increasingly important and is controlled by the opal content, whereas attenuation is very low. This leads to the opportunity to predict the opal content from nondestructive P wave velocity measurements at centimeter-scale resolution.

Radionuclide measurements in sediments and water of the Kara Sea

In this report, the results of a 2000-2001 radiogeoecological investigation are presented for the region of the Ob and Yenisei estuaries and the adjacent Kara Sea. In order to study the behaviour and migration of Cs, Sr and Pu radionuclides in a river - sea system experimental research on the distribution of these radionuclides in the water column and surface sediments has been carried out. In addition, the role of suspended and dissolved organic matter on the behaviour of radionuclides in water solutions has been studied. The 137Cs and 239,240Pu concentrations in the upper 0-2cm layer of the sediments varied between 1,4 and 50,0 Bq/kg, with a mean of 12,4 Bq/kg, and between 0,065-1,96 Bq/kg, with a mean of 0,62 Bq/kg, respectively. There is a direct relationship of a specific radioactivity of 137Cs and 239,240Pu in the sediments and the content of clay fraction. The 137Cs, 90Sr and 239,240Pu concentrations in the water samples varied between 0,4 and 7,0 Bq/m**3 (mean of 3,6 Bq/m**3), 0,4 and 9,7 Bq/m**3 (mean of 3,3 Bq/m**3), and 0,01-0,3 Bq/m**3 (mean of 0,02 Bq/m**3), respectively. In the water samples the concentration of the water-soluble species l37Cs increases with increasing salinity, whereas the concentration of the 90Sr-radionuclide decreases with increasing salinity. This may be related to the physico-chemical behaviour of these radionuclides in water solutions and the influence of several sources on radioactive pollution in this basin. In sea water the suspended matter may absorb up to 10% 137Cs, 90Sr and 239,240Pu, in river water samples these values may reach 15-30%. More than 50% 90Sr and 239,240Pu is able to form complexes with dissolved organic matter. This effect is smaller in saline water. The comparison of the data of 137Cs radioactivity in the surface sediments in 1995 and 2000-2001 showed that the level of radioactivity has decreased.

Anti-osteoporosis activity of Astragalus membranaceus Bunge extract in experimental rats

Purpose: To investigate the anti-osteoporosis effect of Astragalus membranaceus (Fisch.) Bunge. extract (AMBE) in experimental rats. Method: Female Sprague-Dawley rats were randomly divided into six groups: control group, ovariectomy (OVX) with vehicle group, OVX with 17β-estradiol (E2, 25 μg/kg/day) group, and OVX with AMBE doses (60, 120 and 240 mg/kg/day) groups. Daily oral administration of AMBE or E2 was started 4 weeks after OVX and lasted for 16 weeks. The bone mineral density (BMD) of L4 vertebrae and right femurs was evaluated. The length of each femur was measured with a micrometer, and the center of diaphysis was determined. Three representative L4 vertebrae were selected to evaluate trabecular microarchitecture. Serum alkaline phosphatase (ALP), urinary calcium (U-Ca), urinary phosphorus (UP), urinary creatinine (Cr) and osteocalcin (OC) levels were measured. Results: AMBE dose-dependently inhibited the bone mineral density (BMD) reduction of L4 vertebrae (0.27 ± 0.03 g/cm2, p < 0.05) and femurs (0.23 ± 0.03 g/cm2, p < 0.05) caused by OVX and prevented the deterioration of trabecular microarchitecture (p < 0.05), which were accompanied by a significant decrease in skeletal remodeling (p < 0.05) as evidenced by the lower levels of bone turnover markers. A higher dosage of AMBE treatment (240 mg/kg/day) increased U-Ca/Cr (0.27 ± 0.03 mmol/mmol), ALP (137.23 ± 16.72 U/L), U-P/Cr (4.18 ± 0.27 mmol/mmol) and OC (8.47 ± 0.26 mmol/L) levels (both p < 0.05). Conclusion: The findings of this study indicate that AMBE prevents OVX-induced osteoporosis in rats.

Annual crop rotation of tropical pastures with no-till soil as affectedby lime surface application.

Soil acidity and low natural fertility are the main limiting factors for grain production in tropical regionssuch as the Brazilian Cerrado. The application of lime to the surface of no-till soil can improve plant nutrition, dry matter production, crop yields and revenue. The present study, conducted at the Lageado Experimental Farm in Botucatu, State of São Paulo, Brazil, is part of an ongoing research project initi-ated in 2002 to evaluate the long-term effects of the surface application of lime on the soil?s chemical attributes, nutrition and kernel/grain yield of peanut (Arachis hypogaea), white oat (Avena sativa L.) and maize (Zea mays L.) inter cropped with palisade grass (Urochloa brizantha cv. Marandu), as well as the forage dry matter yield of palisade grass in winter/spring, its crude protein concentration, estimated meat production, and revenue in a tropical region with a dry winter during four growing seasons. The experiment was designed in randomized blocks with four replications. The treatments consisted of four rates of lime application (0, 1000, 2000 and 4000 kg ha−1), performed in November 2004. The surface application of limestone to the studied tropical no-till soil was efficient in reducing soil acidity from the surface down to a depth of 0.60 m and resulted in greater availability of P and K at the soil surface. Ca and Mg availability in the soil also increased with the lime application rate, up to a depth of 0.60 m. Nutrient absorption was enhanced with liming, especially regarding the nutrient uptake of K, Ca and Mg by plants.Significant increases in the yield components and kernel/grain yields of peanut, white oat and maize were obtained through the surface application of limestone. The lime rates estimated to achieve the maximum grain yield, especially in white oat and maize, were very close to the rates necessary to increase the base saturation of a soil sample collected at a depth of 0?0.20 m to 70%, indicating that the surface liming of 2000 kg ha−1is effective for the studied tropical no-till soil. This lime rate also increases the forage dry matter yield, crude protein concentration and estimated meat production during winter/spring in the maize-palisade grass inter cropping, provides the highest total and mean net profit during the four growing seasons, and can improve the long-term sustainability of tropical agriculture in the Brazilian Cerrado.

Dalla generazione di modelli 3D densi mediante TLS e fotogrammetria alla modellazione BIM

La tesi tratta la ricerca di procedure che permettano di rilevare oggetti utilizzando il maggior numero di informazioni geometriche ottenibili da una nuvola di punti densa generata da un rilievo fotogrammetrico o da TLS realizzando un modello 3D importabile in ambiente FEM. Il primo test si è eseguito su una piccola struttura, 1.2x0.5x0.2m, in modo da definire delle procedure di analisi ripetibili; la prima consente di passare dalla nuvola di punti “Cloud” all’oggetto solido “Solid” al modello agli elementi finiti “Fem” e per questo motivo è stata chiamata “metodo CSF”, mentre la seconda, che prevede di realizzare il modello della struttura con un software BIM è stata chiamata semplicemente “metodo BIM”. Una volta dimostrata la fattibilità della procedura la si è validata adottando come oggetto di studio un monumento storico di grandi dimensioni, l’Arco di Augusto di Rimini, confrontando i risultati ottenuti con quelli di altre tesi sulla medesima struttura, in particolare si è fatto riferimento a modelli FEM 2D e a modelli ottenuti da una nuvola di punti con i metodi CAD e con un software scientifico sviluppato al DICAM Cloud2FEM. Sull’arco sono state eseguite due tipi di analisi, una lineare sotto peso proprio e una modale ottenendo risultati compatibili tra i vari metodi sia dal punto di vista degli spostamenti, 0.1-0.2mm, che delle frequenze naturali ma si osserva che le frequenze naturali del modello BIM sono più simili a quelle dei modelli generati da cloud rispetto al modello CAD. Il quarto modo di vibrare invece presenta differenze maggiori. Il confronto con le frequenze naturali del modello FEM ha restituito differenze percentuali maggiori dovute alla natura 2D del modello e all’assenza della muratura limitrofa. Si sono confrontate le tensioni normali dei modelli CSF e BIM con quelle ottenute dal modello FEM ottenendo differenze inferiori a 1.28 kg/cm2 per le tensioni normali verticali e sull’ordine 10-2 kg/cm2 per quelle orizzontali.

Beneficial effects of exercise : shifting the focus from body weight to other markers of health

Background: Exercise is widely promoted as a method of weight management, while the other health benefits are often ignored. The purpose of this study was to examine whether exercise-induced improvements in health are influenced by changes in body weight. Methods: Fifty-eight sedentary overweight/obese men and women (BMI 31.8 (SD 4.5) kg/m2) participated in a 12-week supervised aerobic exercise intervention (70% heart rate max, five times a week, 500 kcal per session). Body composition, anthropometric parameters, aerobic capacity, blood pressure and acute psychological response to exercise were measured at weeks 0 and 12. Results: The mean reduction in body weight was −3.3 (3.63) kg (p<0.01). However, 26 of the 58 participants failed to attain the predicted weight loss estimated from individuals’ exercise-induced energy expenditure. Their mean weight loss was only −0.9 (1.8) kg (p<0.01). Despite attaining a lower-than-predicted weight reduction, these individuals experienced significant increases in aerobic capacity (6.3 (6.0) ml/kg/min; p<0.01), and a decreased systolic (−6.00 (11.5) mm Hg; p<0.05) and diastolic blood pressure (−3.9 (5.8) mm Hg; p<0.01), waist circumference (−3.7 (2.7) cm; p<0.01) and resting heart rate (−4.8 (8.9) bpm, p<0.001). In addition, these individuals experienced an acute exercise-induced increase in positive mood. Conclusions: These data demonstrate that significant and meaningful health benefits can be achieved even in the presence of lower-than-expected exercise-induced weight loss. A less successful reduction in body weight does not undermine the beneficial effects of aerobic exercise. From a public health perspective, exercise should be encouraged and the emphasis on weight loss reduced.

Effect of the Summer Months on Body Weight and Composition in College Women

BACKGROUND AND OBJECTIVES: College students and young adults are experiencing the greatest increases in rates of obesity, and 20% of college students are classified as obese. The objective of this study was to compare changes and rates of change in body weight and body composition between the freshman academic year and the summer after the freshman year among female college students. METHODS: Participants were recruited early in their freshman year of college to participate in a prospective longitudinal study examining changes in body weight and composition over the college years. Height and weight were measured, and body composition was assessed using dual energy x-ray absorptiometry (DEXA) at the beginning and end of the freshman year. Upon return from the summer for their sophomore year, participants returned to have all measurements repeated. Sixty-nine female participants completed all three visits. RESULTS: Body weight increased 1.3 kg during the academic period and an additional 0.1 kg during the summer period. Body mass index (BMI) increased between the first two visits but did not change between the last two visits. However, percent fat increased at each visit. Fat-free mass significantly increased 0.5 kg over the academic year but decreased by 1.1 kg over the summer (p<0.05). Greater rates of change were detected in percent fat, fat-free mass, and BMI during the summer compared with the academic year (p<0.05). CONCLUSIONS: Differences in body composition between the academic and summer periods may reflect changes in living situations between these periods. Unfavorable changes during the summer suggest the need to promote healthy lifestyles to freshman women before they leave campus for the summer

A poly(D,L-lactide) resin for the preparation of tissue engineering scaffolds by stereolithography

Porous polylactide constructs were prepared by stereolithography, for the first time without the use of reactive diluents. Star-shaped poly(D,L-lactide) oligomers with 2, 3 and 6 arms were synthesised, end-functionalised with methacryloyl chloride and photocrosslinked in the presence of ethyl lactate as a non-reactive diluent. The molecular weights of the arms of the macromers were 0.2, 0.6, 1.1 and 5 kg/mol, allowing variation of the crosslink density of the resulting networks. Networks prepared from macromers of which the molecular weight per arm was 0.6 kg/mol or higher had good mechanical properties, similar to linear high molecular weight poly(D,L-lactide). A resin based on a 2-armed poly(D,L-lactide) macromer with a molecular weight of 0.6 kg/mol per arm (75 wt%), ethyl lactate (19 wt%), photo-initiator (6 wt%), inhibitor and dye was prepared. Using this resin, films and computer-designed porous constructs were accurately fabricated by stereolithography. Pre-osteoblasts showed good adherence to these photocrosslinked networks. The proliferation rate on these materials was comparable to that on high molecular weight poly(D,L-lactide) and tissue culture polystyrene.

Ureaplasma colonization of amniotic fluid and efficacy of antenatal corticosteroids for preterm lung maturation in sheep

Objective: To assess the efficacy of maternal betamethasone for improving preterm lung function, in the presence of inflammation induced by amniotic fluid ureaplasma colonization. ----- ----- Study design: Ewes bearing single fetuses were randomized to receive an intra-amniotic injection of Ureaplasma parvum (serovar 6; 2×107 colony forming units) or vehicle at 86±2 days of pregnancy (mean±SD: term is 150d), followed by maternal intramuscular betamethasone (0.5mg/kg) or saline, either 2 or 7 days before delivery of lambs at 123±1d. ----- ----- Results: Amniotic fluid IL-8 was elevated by ureaplasmas (p=0.049) but unaffected by betamethasone. Lung inflammation induced by ureaplasmas was not affected by betamethasone. Lung compliance was increased by ureaplasma colonization (p=0.009) and betamethasone (p=0.042), and effects were additive. Lung surfactant was increased by ureaplasma colonization (p<0.001) and betamethasone 7 days (p=0.001), but not 2 days, before delivery. ----- ----- Conclusion: Inflammation improves preterm lung function due to increases in surfactant. Antenatal corticosteroids further augment lung function, through an apparently independent mechanism.