Traffic queue estimation for metered motorway on-ramps through use of loop detector time occupancies

The primary objective of this study is to develop a robust queue estimation algorithm for motorway on-ramps. Real-time queue information is a vital input for dynamic queue management on metered on-ramps. Accurate and reliable queue information enables the management of on-ramp queue in an adaptive manner to the actual traffic queue size and thus minimises the adverse impacts of queue flush while increasing the benefit of ramp metering. The proposed algorithm is developed based on the Kalman filter framework. The fundamental conservation model is used to estimate the system state (queue size) with the flow-in and flow-out measurements. This projection results are updated with the measurement equation using the time occupancies from mid-link and link-entrance loop detectors. This study also proposes a novel single point correction method. This method resets the estimated system state to eliminate the counting errors that accumulate over time. In the performance evaluation, the proposed algorithm demonstrated accurate and reliable performances and consistently outperformed the benchmarked Single Occupancy Kalman filter (SOKF) method. The improvements over SOKF are 62% and 63% in average in terms of the estimation accuracy (MAE) and reliability (RMSE), respectively. The benefit of the innovative concepts of the algorithm is well justified by the improved estimation performance in congested ramp traffic conditions where long queues may significantly compromise the benchmark algorithm’s performance.

A Kalman filter based queue estimation algorithm using time occupancies for motorway on-ramps

The primary objective of this study is to develop a robust queue estimation algorithm for motorway on-ramps. Real-time queue information is the most vital input for a dynamic queue management that can treat long queues on metered on-ramps more sophistically. The proposed algorithm is developed based on the Kalman filter framework. The fundamental conservation model is used to estimate the system state (queue size) with the flow-in and flow-out measurements. This projection results are updated with the measurement equation using the time occupancies from mid-link and link-entrance loop detectors. This study also proposes a novel single point correction method. This method resets the estimated system state to eliminate the counting errors that accumulate over time. In the performance evaluation, the proposed algorithm demonstrated accurate and reliable performances and consistently outperformed the benchmarked Single Occupancy Kalman filter (SOKF) method. The improvements over SOKF are 62% and 63% in average in terms of the estimation accuracy (MAE) and reliability (RMSE), respectively. The benefit of the innovative concepts of the algorithm is well justified by the improved estimation performance in the congested ramp traffic conditions where long queues may significantly compromise the benchmark algorithm’s performance.

Citation success over time : theory or empirics?

This study investigates the citation patterns of theoretical and empirical papers published in a top economics journal, namely American Economic Review, over a period of almost 30 years, while also exploring the determinants of citation success. The results indicate that empirical papers attract more citation success than theoretical studies. However, the pattern over time is very similar. Moreover, among empirical papers it appears that the cross-country studies are more successful than single country studies focusing on North America data or other regions.

QoS differentiation in IEEE 802.11 wireless local area networks for real-time control

IEEE 802.11 based wireless local area networks (WLANs) are being increasingly deployed for soft real-time control applications. However, they do not provide quality-ofservice (QoS) differentiation to meet the requirements of periodic real-time traffic flows, a unique feature of real-time control systems. This problem becomes evident particularly when the network is under congested conditions. Addressing this problem, a media access control (MAC) scheme, QoS-dif, is proposed in this paper to enable QoS differentiation in IEEE 802.11 networks for different types of periodic real-time traffic flows. It extends the IEEE 802.11e Enhanced Distributed Channel Access (EDCA) by introducing a QoS differentiation method to deal with different types of periodic traffic that have different QoS requirements for real-time control applications. The effectiveness of the proposed QoS-dif scheme is demonstrated through comparisons with the IEEE 802.11e EDCA mechanism.

Translating vision research into policy and practice to improve visibility, and hence safety, of road workers at night

This case study report describes the stages involved in the translation of research on night-time visibility into standards for the safety clothing worn by roadworkers. Vision research demonstrates that when lights are placed on the moveable joints of the body and the person moves in a dark setting, the phenomenon known as “biological motion or biomotion” occurs, enabling rapid and accurate recognition of the human form although only the lights can be seen. QUT was successful in gaining funding from the Australian Research Council for a Linkage grant due to the support of the predecessors of the Queensland Department of Transport and Main Roads (TMR) to research the biomotion effect in on-road settings using materials that feature in roadworker clothing. Although positive results were gained, the process of translating the research results into policy, practices and standards relied strongly on the supportive efforts of TMR staff engaged in the review and promulgation of national standards. The ultimate result was the incorporation of biomotion marking into AS/NZS 4602.1 2011. The experiences gained in this case provide insights into the processes involved in translating research into practice.

The right to choose an assisted death : time for legislation?

The legal framework that operates at the end of life in Australia needs to be reformed. • Voluntary euthanasia and assisted suicide are currently unlawful. • Both activities nevertheless occur not infrequently in Australia, in part because palliative care cannot relieve physical and psychological pain and suffering in all cases. • In this respect, the law is deficient. The law is also unfair because it doesn’t treat people equally. Some people can be helped to die on their own terms as a result of their knowledge and/or connections while some are able to hasten their death by the refusal of life-sustaining treatment. But others do not have access to the means for their life to end. • A very substantial majority of Australians have repeatedly expressed in public opinion polls their desire for law reform on these matters. Many are concerned at what they see is happening to their loved ones as they reach the end of their lives, and want the confidence that when their time comes they will be able to exercise choice in relation to assisted dying. • The most consistent reason advanced not to change the law is the need to protect the vulnerable. There is a concern that if the law allows voluntary euthanasia and assisted suicide for some people, it will be expanded and abused, including pressures being placed on highly dependent people and those with disabilities to agree to euthanasia. • But there is now a large body of experience in a number of international jurisdictions following the legalisation of voluntary euthanasia and/or assisted suicide. This shows that appropriate safeguards can be implemented to protect vulnerable people and prevent the abuse that opponents of assisted dying have feared. It reveals that assisted dying meets a real need among a small minority of people at the end of their lives. It also provides reassurance to people with terminal and incurable disease that they will not be left to suffer the indignities and discomfort of a nasty death. • Australia is an increasingly secular society. Strong opposition to assisted death by religious groups that is based on their belief in divine sanctity of all human life is not a justification for denying choice for those who do not share that belief. • It is now time for Australian legislators to respond to this concern and this experience by legislating to enhance the quality of death for those Australians who seek assisted dying.

Groundwater visualisation system (GVS) : a software framework for integrated display and interrogation of conceptual hydrogeological models, data and time-series animation

Management of groundwater systems requires realistic conceptual hydrogeological models as a framework for numerical simulation modelling, but also for system understanding and communicating this to stakeholders and the broader community. To help overcome these challenges we developed GVS (Groundwater Visualisation System), a stand-alone desktop software package that uses interactive 3D visualisation and animation techniques. The goal was a user-friendly groundwater management tool that could support a range of existing real-world and pre-processed data, both surface and subsurface, including geology and various types of temporal hydrological information. GVS allows these data to be integrated into a single conceptual hydrogeological model. In addition, 3D geological models produced externally using other software packages, can readily be imported into GVS models, as can outputs of simulations (e.g. piezometric surfaces) produced by software such as MODFLOW or FEFLOW. Boreholes can be integrated, showing any down-hole data and properties, including screen information, intersected geology, water level data and water chemistry. Animation is used to display spatial and temporal changes, with time-series data such as rainfall, standing water levels and electrical conductivity, displaying dynamic processes. Time and space variations can be presented using a range of contouring and colour mapping techniques, in addition to interactive plots of time-series parameters. Other types of data, for example, demographics and cultural information, can also be readily incorporated. The GVS software can execute on a standard Windows or Linux-based PC with a minimum of 2 GB RAM, and the model output is easy and inexpensive to distribute, by download or via USB/DVD/CD. Example models are described here for three groundwater systems in Queensland, northeastern Australia: two unconfined alluvial groundwater systems with intensive irrigation, the Lockyer Valley and the upper Condamine Valley, and the Surat Basin, a large sedimentary basin of confined artesian aquifers. This latter example required more detail in the hydrostratigraphy, correlation of formations with drillholes and visualisation of simulation piezometric surfaces. Both alluvial system GVS models were developed during drought conditions to support government strategies to implement groundwater management. The Surat Basin model was industry sponsored research, for coal seam gas groundwater management and community information and consultation. The “virtual” groundwater systems in these 3D GVS models can be interactively interrogated by standard functions, plus production of 2D cross-sections, data selection from the 3D scene, rear end database and plot displays. A unique feature is that GVS allows investigation of time-series data across different display modes, both 2D and 3D. GVS has been used successfully as a tool to enhance community/stakeholder understanding and knowledge of groundwater systems and is of value for training and educational purposes. Projects completed confirm that GVS provides a powerful support to management and decision making, and as a tool for interpretation of groundwater system hydrological processes. A highly effective visualisation output is the production of short videos (e.g. 2–5 min) based on sequences of camera ‘fly-throughs’ and screen images. Further work involves developing support for multi-screen displays and touch-screen technologies, distributed rendering, gestural interaction systems. To highlight the visualisation and animation capability of the GVS software, links to related multimedia hosted online sites are included in the references.

Experimental and computer simulation validation of ultrasound phase interference created by lateral inhomogeneity of transit time in replica bone marrow composite models

Purpose: The measurement of broadband ultrasonic attenuation (BUA) in cancellous bone for the assessment of osteoporosis follows a parabolic-type dependence with bone volume fraction; having minima values corresponding to both entire bone and entire marrow. Langton has recently proposed that the primary BUA mechanism may be significant phase interference due to variations in propagation transit time through the test sample as detected over the phase-sensitive surface of the receive ultrasound transducer. This fundamentally simple concept assumes that the propagation of ultrasound through a complex solid : liquid composite sample such as cancellous bone may be considered by an array of parallel ‘sonic rays’. The transit time of each ray is defined by the proportion of bone and marrow propagated, being a minimum (tmin) solely through bone and a maximum (tmax) solely through marrow. A Transit Time Spectrum (TTS), ranging from tmin to tmax, may be defined describing the proportion of sonic rays having a particular transit time, effectively describing lateral inhomogeneity of transit time over the surface of the receive ultrasound transducer. Phase interference may result from interaction of ‘sonic rays’ of differing transit times. The aim of this study was to test the hypothesis that there is a dependence of phase interference upon the lateral inhomogenity of transit time by comparing experimental measurements and computer simulation predictions of ultrasound propagation through a range of relatively simplistic solid:liquid models exhibiting a range of lateral inhomogeneities. Methods: A range of test models was manufactured using acrylic and water as surrogates for bone and marrow respectively. The models varied in thickness in one dimension normal to the direction of propagation, hence exhibiting a range of transit time lateral inhomogeneities, ranging from minimal (single transit time) to maximal (wedge; ultimately the limiting case where each sonic ray has a unique transit time). For the experimental component of the study, two unfocused 1 MHz ¾” broadband diameter transducers were utilized in transmission mode; ultrasound signals were recorded for each of the models. The computer simulation was performed with Matlab, where the transit time and relative amplitude of each sonic ray was calculated. The transit time for each sonic ray was defined as the sum of transit times through acrylic and water components. The relative amplitude considered the reception area for each sonic ray along with absorption in the acrylic. To replicate phase-sensitive detection, all sonic rays were summed and the output signal plotted in comparison with the experimentally derived output signal. Results: From qualtitative and quantitative comparison of the experimental and computer simulation results, there is an extremely high degree of agreement of 94.2% to 99.0% between the two approaches, supporting the concept that propagation of an ultrasound wave, for the models considered, may be approximated by a parallel sonic ray model where the transit time of each ray is defined by the proportion of ‘bone’ and ‘marrow’. Conclusions: This combined experimental and computer simulation study has successfully demonstrated that lateral inhomogeneity of transit time has significant potential for phase interference to occur if a phase-sensitive ultrasound receive transducer is implemented as in most commercial ultrasound bone analysis devices.

Studies in power hardware in the loop (PHIL) simulation using real-time digital simulator (RTDS)

In power hardware in the loop (PHIL) simulations, a real-time simulated power system is interfaced to a piece of hardware, usually called hardware under test (HuT). A PHIL test can be realized using several simulation tools. Among them Real Time Digital Simulator (RTDS) is an ideal tool to perform complex power system simulations in near real-time. Stable operation of the entire system, along with the accuracy of simulation results are the main concerns regarding a PHIL simulation. In this paper, a simulated power network on RTDS will be interfaced to HuT through a voltage source converter (VSC). Issues around stability and other interface problems are studied and a new method to stabilize some unstable PHIL cases is proposed. PHIL simulation results in PSCAD and RSCAD are presented.

Sitting-time, physical activity and depressive symptoms in mid-aged women

Background: Associations between sitting-time and physical activity (PA) with depression are unclear. Purpose: To examine concurrent and prospective associations between both sitting-time and PA with prevalent depressive symptoms in mid-aged Australian women. Methods: Data were from 8,950 women, aged 50-55 years in 2001, who completed mail surveys in 2001, 2004, 2007 and 2010. Depressive symptoms were assessed using the Center for Epidemiological Studies Depression questionnaire. Associations between sitting-time (≤4, >4-7, >7 hrs/day) and PA (none, some, meeting guidelines) with depressive symptoms (symptoms/no symptoms) were examined in 2011 in concurrent and lagged mixed effect logistic modeling. Both main effects and interaction models were developed. Results: In main effects modeling, women who sat >7 hrs/day (OR 1.47, 95%CI 1.29-1.67) and women who did no PA (OR 1.99, 95%CI 1.75-2.27) were more likely to have depressive symptoms than women who sat ≤4 hrs/day and who met PA guidelines, respectively. In interaction modeling, the likelihood of depressive symptoms in women who sat >7 hrs/day and did no PA was triple that of women who sat ≤4 hrs/day and met PA guidelines (OR 2.96, 95%CI 2.37-3.69). In prospective main effects and interaction modeling, sitting-time was not associated with depressive symptoms, but women who did no PA were more likely than those who met PA guidelines to have future depressive symptoms (OR 1.26, 95%CI 1.08-1.47). Conclusions: Increasing PA to a level commensurate with PA guidelines can alleviate current depression symptoms and prevent future symptoms in mid-aged women. Reducing sitting-time may ameliorate current symptoms.

Vitamin D status and skin cancer risk independent of time outdoors : 11-year prospective study in and Australian community

Vitamin D may have anti-skin cancer effects, but population-based evidence is lacking. We therefore assessed associations between vitamin D status and skin cancer risk in an Australian subtropical community. We analyzed prospective skin cancer incidence for 11 years following baseline assessment of serum 25(OH)-vitamin D in 1,191 adults (average age 54 years) and used multivariable logistic regression analysis to adjust risk estimates for age, sex, detailed assessments of usual time spent outdoors, phenotypic characteristics, and other possible confounders. Participants with serum 25(OH)-vitamin D concentrations above 75 nmol  l(-1) versus those below 75 nmol  l(-1) more often developed basal cell carcinoma (odds ratio (OR)=1.51 (95% confidence interval (CI): 1.10-2.07, P=0.01) and melanoma (OR=2.71 (95% CI: 0.98-7.48, P=0.05)). Squamous cell carcinoma incidence tended to be lower in persons with serum 25(OH)-vitamin D concentrations above 75 nmol  l(-1) compared with those below 75 nmol  l(-1) (OR=0.67 (95% CI: 0.44-1.03, P=0.07)). Vitamin D status was not associated with skin cancer incidence when participants were classified as above or below 50 nmol  l(-1) 25(OH)-vitamin D. Our findings do not indicate that the carcinogenicity of high sun exposure can be counteracted by high vitamin D status. High sun exposure is to be avoided as a means to achieve high vitamin D status.

Performance configurations over time: implications for growth-and profit-oriented strategies

Entrepreneurship research and practice places emphasis on company growth as a measure of entrepreneurial success. In many cases, there has been a tendency to give growth a very central role, with some researchers even seeing growth as the very essence of entrepreneurship (Cole, 1949; Sexton, 1997; Stevenson & Gumpert, 1991). A large number of empirical studies of the performance of young and/or small firms use growth as the dependent variable (see reviews by Ardishvili, Cardozo, Harmon, & Vadakath, 1998; Delmar, 1997; Wiklund, 1998). By contrast, the two most prominent views of strategic management – strategic positioning (Porter, 1980) and the resource-based view (Barney, 1991; Wernerfelt, 1984) – are both concerned with achieving competitive advantage and regard achieving economic rents and profitability relative to other competitors as the central measures of firm performance. Strategic entrepreneurship integrates these two perspectives and is simultaneously concerned with opportunity seeking and advantage seeking (Hitt, Ireland, Camp, & Sexton, 2002; Ireland, Hitt, & Sirmon, 2003). Consequently, both company growth and relative profitability are together relevant measures of firm performance in the domain of strategic entrepreneurship.

Nutritional analysis of gastric contents and body condition score at a single time point in feral horses in Australia

Objective: To determine the impact of a free-choice diet on nutritional intake and body condition of feral horses. Animals: Cadavers of 41 feral horses from 5 Australian locations. Procedures: Body condition score (BCS) was determined (scale of 1 to 9), and the stomach was removed from horses during postmortem examination. Stomach contents were analyzed for nutritional variables and macroelement and microelement concentrations. Data were compared among the locations and also compared with recommended daily intakes for horses. Results: Mean BCS varied by location; all horses were judged to be moderately thin. The BCS for males was 1 to 3 points higher than that of females. Amount of protein in the stomach contents varied from 4.3% to 14.9% and was significantly associated with BCS. Amounts of water-soluble carbohydrate and ethanol-soluble carbohydrate in stomach contents of feral horses from all 5 locations were higher than those expected for horses eating high-quality forage. Some macroelement and microelement concentrations were grossly excessive, whereas others were grossly deficient. There was no evidence of ill health among the horses. Conclusions and Clinical Relevance: Results suggested that the diet for several populations of feral horses in Australia appeared less than optimal. However, neither low BCS nor trace mineral deficiency appeared to affect survival of the horses. Additional studies on food sources in these regions, including analysis of water-soluble carbohydrate, ethanol-soluble carbohydrate, and mineral concentrations, are warranted to determine the provenance of such rich sources of nutrients. Determination of the optimal diet for horses may need revision.

Combined electrophoretic deposition–anodization method to fabricate reduced graphene oxide–TiO2 nanotube films

We directly constructed reduced graphene oxide–titanium oxide nanotube (RGO–TNT) film using a single-step, combined electrophoretic deposition–anodization (CEPDA) method. This method, based on the simultaneous anodic growth of tubular TiO2 and the electrophoretic-driven motion of RGO, allowed the formation of an effective interface between the two components, thus improving the electron transfer kinetics. Composites of these graphitic carbons with different levels of oxygen-containing groups, electron conductivity and interface reaction time were investigated; a fine balance of these parameters was achieved.

Analysis of regionally enhanced GPS orbit and clock solutions and contribution to improvement of real-time precise point positioning

This work experimentally examines the performance benefits of a regional CORS network to the GPS orbit and clock solutions for supporting real-time Precise Point Positioning (PPP). The regionally enhanced GPS precise orbit solutions are derived from a global evenly distributed CORS network added with a densely distributed network in Australia and New Zealand. A series of computational schemes for different network configurations are adopted in the GAMIT-GLOBK and PANDA data processing. The precise GPS orbit results show that the regionally enhanced solutions achieve the overall orbit improvements with respect to the solutions derived from the global network only. Additionally, the orbital differences over GPS satellite arcs that are visible by any of the five Australia-wide CORS stations show a higher percentage of overall improvements compared to the satellite arcs that are not visible from these stations. The regional GPS clock and Uncalibrated Phase Delay (UPD) products are derived using the PANDA real time processing module from Australian CORS networks of 35 and 79 stations respectively. Analysis of PANDA kinematic PPP and kinematic PPP-AR solutions show certain overall improvements in the positioning performance from a denser network configuration after solution convergence. However, the clock and UPD enhancement on kinematic PPP solutions is marginal. It is suggested that other factors, such as effects of ionosphere, incorrectly fixed ambiguities, may be the more dominating, deserving further research attentions.