Thermal stability of newberyite Mg(PO3OH)•3H2O – a cave mineral from Skipton lava tubes, Victoria, Australia.

The mineral newberyite Mg(PO3OH)•3H2O is a mineral that has been found in caves such as the Skipton Lava Tubes (SW of Ballarat, Victoria, Australia), Moorba cave, Jurien Bay, Western Australia, and in the Petrogale Cave (Madura , Eucla, Western Australia). Because these minerals contain water, the minerals lend themselves to thermal analysis. The mineral newberyite is found to decompose at 145°C with a water loss of 31.96%, a result which is very close to the theoretical value. The result shows that the mineral is not stable in caves where the temperature exceeds this value. The implication of this result rests with the removal of kidney stones, which have the same composition as newberyite. Point heating focussing on the kidney stone results in the destruction of the kidney stone.

Thermal stability of crandallite CaAl3(PO4)2(OH)5•(H2O) – a ‘cave’ mineral from the Jenolan Caves

Thermogravimetry combined with evolved gas mass spectrometry has been used to characterise the mineral crandallite CaAl3(PO4)2(OH)5•(H2O) and to ascertain the thermal stability of this ‘cave’ mineral. X-ray diffraction proves the presence of the mineral and identifies the products after thermal decomposition. The mineral crandallite is formed through the reaction of calcite with bat guano. Thermal analysis shows that the mineral starts to decompose through dehydration at low temperatures at around 139°C while dehydroxylation occurs over the temperature range 200 to 700°C with loss of OH units. The critical temperature for OH loss is around 416°C and above this temperature the mineral structure is altered. Some minor loss of carbonate impurity occurs at 788°C. This study shows the mineral is unstable above 139°C. This temperature is well above the temperature in caves, which have a maximum temperature of 15°C. A chemical reaction for the synthesis of crandallite is offered and the mechanism for the thermal decomposition is given.

A mask-based approach for the geometric calibration of thermal-infrared cameras

Accurate and efficient thermal-infrared (IR) camera calibration is important for advancing computer vision research within the thermal modality. This paper presents an approach for geometrically calibrating individual and multiple cameras in both the thermal and visible modalities. The proposed technique can be used to correct for lens distortion and to simultaneously reference both visible and thermal-IR cameras to a single coordinate frame. The most popular existing approach for the geometric calibration of thermal cameras uses a printed chessboard heated by a flood lamp and is comparatively inaccurate and difficult to execute. Additionally, software toolkits provided for calibration either are unsuitable for this task or require substantial manual intervention. A new geometric mask with high thermal contrast and not requiring a flood lamp is presented as an alternative calibration pattern. Calibration points on the pattern are then accurately located using a clustering-based algorithm which utilizes the maximally stable extremal region detector. This algorithm is integrated into an automatic end-to-end system for calibrating single or multiple cameras. The evaluation shows that using the proposed mask achieves a mean reprojection error up to 78% lower than that using a heated chessboard. The effectiveness of the approach is further demonstrated by using it to calibrate two multiple-camera multiple-modality setups. Source code and binaries for the developed software are provided on the project Web site.

The role of physical activity in the lives of people with lymphoedema following cancer treatment : a social constructionist study

Lymphoedema is a chronic condition predominantly affecting the limbs, although it can involve the trunk and other areas of the body. It is characterised by swelling due to excess accumulation of fluid in body tissues. Secondary lymphoedema, which arises following cancer treatment, is the more common form of lymphoedema in developed countries. At least 20% of those diagnosed with the most common cancers will develop lymphoedema. This is a concern in Australia as incidence of these cancers is increasing. Cancer survival rates are also increasing. Currently, this equates to 9 300 new cases of secondary lymphoedema diagnosed each year. Considerable physical and psychosocial impacts of lymphoedema have been reported and its subsequent impact on health-related quality of life can exacerbate other side effects of cancer treatment. Exercise following cancer treatment has been shown to significantly reduce the impact of treatment side effects, improve quality of life and physical status. While participating in exercise does not increase risk nor exacerbate existing lymphoedema, reductions in incidence of lymphoedema exacerbations and associated symptoms have been observed in women participating in regular weight lifting following breast cancer treatment. Despite these benefits, lymphoedema prevention and management advice cautions people with lymphoedema against „repetitive use. or „overuse. of their affected arm. It is possible that this advice creates a barrier to participation in physical activity; however, little is known about the relationship between physical activity and lymphoedema. In addition, the majority of studies examining the experiences of people living with lymphoedema and the impact of the condition have been predominantly conducted internationally and have focused on women following breast cancer. This study sought to explore firstly, how men and women construct their experience of living with lymphoedema following treatment for a range of cancers in the context of everyday life in Australia; and secondly, to analyse the role of physical activity in the lives of those living with lymphoedema following cancer treatment. A social constructivist grounded theory approach was taken to explore these objectives as it is acknowledged that human actions and the meanings associated with these actions are influenced by the interaction between the self and the social world. It is also acknowledged that the research process itself is a social construction between the researcher and participant. Purposive sampling techniques were used to recruit a total of 29 participants from a variety of sources. Telephone interviews and focus groups were conducted to collect data. Data were concurrently collected and analysed and analysis was conducted using the constant comparative method. The core category that developed in objective one was „sense of self‟. The self was defined by perceptions participants held of themselves and their identity prior to a lymphoedema diagnosis and changes to their perceptions and identity since diagnosis. Three conceptual categories which related to each other and to „sense of self‟ were developed through the process of coding that represented the process of how participants constructed their experiences living with secondary lymphoedema in the context of everyday life. Firstly, altered normalcy reflected the physical and psychosocial changes experienced and the effect it had on their lives. Secondly, „accidental journey‟ reflected participants‟ journey with the heath care system prior to diagnosis through to longer term management. Thirdly, renegotiating control revealed participants perceived control over lymphoedema and their ability to participate in daily activities previously enjoyed. These findings revealed the failure of the broader health system to recognise the significant and chronic nature of a lymphoedema diagnosis following cancer treatment with greater understanding, knowledge and support from health professionals being needed. The findings also reveal access to health professionals trained in lymphoedema management, a comprehensive approach encompassing both physical and psychosocial needs and provision of practical and meaningful guidelines supported by scientific evidence would contribute to improved treatment and management of the condition. The key findings for objective two were that people with lymphoedema define physical activity in different ways. Physical activity post-diagnosis was perceived as important by most for a variety of reasons ranging from everyday functioning, to physical and psychosocial health benefits. Issues relating to the impact of lymphoedema on physical activity related to the impact on peoples‟ ability to be physically active, confusion about acceptable forms of physical activity and barriers that lymphoedema presented to being physically active. A relationship between how people construct their experiences with lymphoedema and the role of physical activity was also established. The contribution of physical activity to the lives of people living with lymphoedema following cancer treatment appeared to be influenced by their sense of self as socially constructed through their experiences prior to diagnosis and following diagnosis with lymphoedema. The influence of pre-lymphoedema habits, norms and beliefs suggests the importance of effective health promotion messages to encourage physical activity among the general population and specific messages and guidelines particular to the needs of those diagnosed with lymphoedema following cancer treatment. The influence of participant.s social constructions on the lymphoedema experience highlights the importance of improving interactions between the overall health care system and patients, providing a clear treatment plan, providing evidence-based and clear advice about participation in appropriate physical activity, which in doing so will limit the physical and psychosocial effect of lymphoedema and providing comprehensive physical and psychosocial support to those living with the condition and their families. This study has contributed to a deep understanding of people.s experiences with lymphoedema following cancer treatment and the role of physical activity in the context of daily life in Australia. Findings from this study lead to recommendations for advocacy, a comprehensive approach to diagnosis, treatment and management, and specific areas for future research.

Numerical models to simulate the thermal performance of LSF wall panels

Fire safety of buildings has been recognised as very important by the building industry and the community at large. Gypsum plasterboards are widely used to protect light gauge steel frame (LSF) walls all over the world. Gypsum contains free and chemically bound water in its crystal structure. Plasterboard also contains gypsum (CaSO4.2H2O) and calcium carbonate (CaCO3). The dehydration of gypsum and the decomposition of calcium carbonate absorb heat, and thus are able to protect LSF walls from fires. Kolarkar and Mahendran (2008) developed an innovative composite wall panel system, where the insulation was sandwiched between two plasterboards to improve the thermal and structural performance of LSF wall panels under fire conditions. In order to understand the performance of gypsum plasterboards and LSF wall panels under standard fire conditions, many experiments were conducted in the Fire Research Laboratory of Queensland University of Technology (Kolarkar, 2010). Fire tests were conducted on single, double and triple layers of Type X gypsum plasterboards and load bearing LSF wall panels under standard fire conditions. However, suitable numerical models have not been developed to investigate the thermal performance of LSF walls using the innovative composite panels under standard fire conditions. Continued reliance on expensive and time consuming fire tests is not acceptable. Therefore this research developed suitable numerical models to investigate the thermal performance of both plasterboard assemblies and load bearing LSF wall panels. SAFIR, a finite element program, was used to investigate the thermal performance of gypsum plasterboard assemblies and LSF wall panels under standard fire conditions. Appropriate values of important thermal properties were proposed for plasterboards and insulations based on laboratory tests, literature review and comparisons of finite element analysis results of small scale plasterboard assemblies from this research and corresponding experimental results from Kolarkar (2010). The important thermal properties (thermal conductivity, specific heat capacity and density) of gypsum plasterboard and insulation materials were proposed as functions of temperature and used in the numerical models of load bearing LSF wall panels. Using these thermal properties, the developed finite element models were able to accurately predict the time temperature profiles of plasterboard assemblies while they predicted them reasonably well for load bearing LSF wall systems despite the many complexities that are present in these LSF wall systems under fires. This thesis presents the details of the finite element models of plasterboard assemblies and load bearing LSF wall panels including those with the composite panels developed by Kolarkar and Mahendran (2008). It examines and compares the thermal performance of composite panels developed based on different insulating materials of varying densities and thicknesses based on 11 small scale tests, and makes suitable recommendations for improved fire performance of stud wall panels protected by these composite panels. It also presents the thermal performance data of LSF wall systems and demonstrates the superior performance of LSF wall systems using the composite panels. Using the developed finite element of models of LSF walls, this thesis has proposed new LSF wall systems with increased fire rating. The developed finite element models are particularly useful in comparing the thermal performance of different wall panel systems without time consuming and expensive fire tests.

Embracing Sharia-Compliant products through regulatory amendment to achieve parity of treatment

This article recognises the potential importance of Islamic finance products in Australia, along with the current regulatory impediments preventing Australia from becoming a leader in the Asia-Pacific Islamic finance market. Taking into account the potential importance of, and impediments to, Islamic finance, this article highlights, through the historical development and contemporary state of Islamic finance, its economic, social and political benefits to Australia. Once a case for embracing Islamic finance is made, the main current regulatory impediments to Australia becoming a key player in the Islamic finance market within the Asia-Pacific region are highlighted. This article then argues that, rather than requiring any separate regulatory regime, the current regulatory impediments may be overcome through amendments to existing laws to ensure parity of treatment in Australia between the Islamic finance market and the conventional finance market. The Australian income tax regime is utilised as a case study demonstrate how parity of treatment could be achieved via amendment by taking two frequent and separate Islamic finance transactions. This article concludes that the economic, social and political benefits potentially warrant Australia embracing Islamic finance and that, with the right regulatory measures, Australia could lay the foundation to become a leader in the Asia-Pacific Islamic finance market.

The use of thermal imaging in assessing skin temperature following cryotherapy : a review

Nineteen studies met the inclusion criteria. A skin temperature reduction of 5–15 °C, in accordance with the recent PRICE (Protection, Rest, Ice, Compression and Elevation) guidelines, were achieved using cold air, ice massage, crushed ice, cryotherapy cuffs, ice pack, and cold water immersion. There is evidence supporting the use and effectiveness of thermal imaging in order to access skin temperature following the application of cryotherapy. Thermal imaging is a safe and non-invasive method of collecting skin temperature. Although further research is required, in terms of structuring specific guidelines and protocols, thermal imaging appears to be an accurate and reliable method of collecting skin temperature data following cryotherapy. Currently there is ambiguity regarding the optimal skin temperature reductions in a medical or sporting setting. However, this review highlights the ability of several different modalities of cryotherapy to reduce skin temperature.

Zinc aluminium layered double hydroxides for the removal of iodine and iodide from aqueous solutions

129I is a radioactive isotope of iodine that is readily absorbed by the body. In this paper we investigated the potential of a 3:1 Zn/Al layered double hydroxide (LDH) as a sorbent for the removal of iodine and iodide from water. Synthetic Zn6Al2(OH)16(CO3)∙4H2O was prepared by the co-precipitation before thermal activation. The LDH was treated with solutions containing iodide and iodine. It was found that iodine could be more easily removed from solution than iodide. Powder X-ray diffraction revealed the destruction of the LDH structure during thermal activation and the successful reformation of a similar LDH material after treatment with the iodide or iodine solution. Thermal decomposition of all samples studied by thermogravimetry appeared to be similar. A new decomposition mechanism similar to one previously described in the literature was proposed for the Zn/Al LDH. The total mass loss of samples treated with iodide and iodine was significantly lower than that of the original LDH indicating that iodine species may form non-removable anions when intercalated into the LDH structure. Evolved gas mass spectrometry failed to detect any iodine species lost as gases during the decomposition of iodide treated LDH however, small quantities of iodine species were observed during decomposition of samples treated with iodine solution.

Porous Ca-Si-based nanospheres : a potential intra-canal disinfectant-carrier for infected canal treatment

The aim of this study is to develop a new intra-canal disinfectant-carrier for infected canal treatment. To achieve this purpose, a new porous Ca-Si (CS)-based nanosphere was synthesized and characterized. Results showed that the nanospheres can infiltrate into dentinal tubules and released the ampicillin over one week time in a sustained manner. The release of ampicillin from spheres has significantly antibacterial property. Extensive and well-organized in vitro mineralization and crystallization of apatite were induced on the surface of dentin slices covered by CS nanospheres. All these features indicate that the porous CS nanospheres may be developed into a new intra-canal disinfectant-carrier for infected canal treatment.

Quality-of-life among head and neck cancer survivors at one year after treatment – A systematic review

Abstract Background: The importance of quality-of-life (QoL) research has been recognised over the past two decades in patients with head and neck (H&N) cancer. The aims of this systematic review are to evaluate the QoL status of H&N cancer survivors one year after treatment and to identify the determinants affecting their QoL. Methods: Pubmed, Medline, Scopus, Sciencedirect and CINAHL (2000–2011) were searched for relevant studies, and two of the present authors assessed their methodological quality. The characteristics and main findings of the studies were extracted and reported. Results: Thirty-seven studies met the inclusion criteria, and the methodological quality of the majority was moderate to high. While patients of the group in question recover their global QoL by 12 months after treatment, a number of outstanding issues persist – deterioration in physical functioning, fatigue, xerostomia and sticky saliva. Age, cancer site, stage of disease, social support, smoking, feeding tube placement and alcohol consumption are the significant determinants of QoL at 12 months, while gender has little or no influence. Conclusions: Regular assessments should be carried out to monitor physical functioning,degree of fatigue, xerostomia and sticky saliva. Further research is required to develop appropriate and effective interventions to deal with these issues, and thus to promote the patients’ QoL.

Inactivation and structural changes of E. Cloacae and B. Subtilis Endospores during IR laser water treatment

IR radiation has been studied for micro-organism inactivation of bacterial spores on metal substrates [1] and on metal and paper substrates [2]. A near-point near infrared laser water treatment apparatus for use in dental hand-pieces was also developed [3]. To date water sterilisation research using a mid-IR laser technique is very rare. According to the World Health Organisation [4], examinations for faecal indicator bacteria remain the most sensitive and specific way of assessing the hygienic quality of water. Bacteria that fall into this group are E. coli, other coliform bacteria (including E. cloacae) and to a lesser extent, faecal streptococci [5]. Protozoan cysts from organisms which cause giardiasis are the most frequently identified cause of waterborne diseases in developed countries [6,7]. The use of aerobic bacterial endospores to monitor the efficiency of various water treatments has been shown to provide a reliable and simple indicator of overall performance of water treatment[8,9].The efficacy of IR radiation for water disinfection compared to UV treatment has been further investigated in the present study. In addition FTIR spectroscopy in conjunction with Principle Component Analysis was used to characterise structural changes within the bacterial cells and endospores following IR laser treatment. Changes in carbohydrate content of E. cloacae following IR laser treatment were observed.