Determination of activation energy for thermal regeneration of EL2 from its metastable state by thermally stimulated photocurrent measurements

It is shown that thermally stimulated photocurrent measurements provide a simple and effective method of determining the activation energy of thermal regeneration rate of EL2 from the metastable state to the normal state in undoped semi‐insulating GaAs. The thermal regeneration rate r is found to be 2.5×108 exp(−0.26 eV/kT) s−1.

Flame retardant polyphosphate esters: 1. Condensation polymers of bisphenols with aryl phosphorodichloridates: synthesis, characterization and thermal studies

Polyphosphate esters were synthesized by the solution polycondensation of bisphenols with aryl phosphorodichloridates. The polymers were characterized by i.r. and 1H, 13C and 31P n.m.r. spectroscopy. The molecular weights were determined by end group analysis using 1H and 31P n.m.r. spectral data. The thermal stability of the polymers was analysed by thermogravimetry.

Flame retardant polyphosphate esters: 2. Condensation polymers of bisphenol A with alkyl phosphorodichloridates: synthesis, characterization and thermal studies

Polyphosphate esters based on bisphenol A and alkyl phosphorodichloridates have been synthesized and characterized by i.r. and n.m.r. spectroscopy. The molecular weights were calculated from 31P n.m.r. The thermal stability of the polymers were analysed by thermogravimetry.

Growth of titanium oxide overlayers by thermal oxidation of titanium

This paper describes a theoretical model for the growth of titanium oxide by thermal oxidation of titanium. It is shown that this model can explain the formation of layers of different oxides of titanium and the changes in these layers with variations in the conditions of oxidation. Some experimental X-ray diffraction results which support the model are also given.

Correlation of acoustic and thermal anomalies in ferroelectric crystals

The Pippard-Janovec relations are derived for correlating the anomalous elastic coefficient and the anomalous specific heat near the phase transitions of ferroelectric crystals. These relations are verified in the case of ferroelectric triglycine selenate crystal.

Thermal expansion and phase transition in NaVO3

The present x-ray study has been undertook in order to correlate the phase transition in sodium metavanadate NaVO3 crystal with its structural aspects. The thermal expansion behaviour of NaVO3 was studied from room temperature up to 500 C, well beyond the transition temperature.

Thermal stresses in a spherical shell with a conical nozzle

A thermal stress problem of a spherical shell with a conical nozzle is solved using a continuum approach. The thermal loading consists of a steady temperature which is uniform on the inner and outer surfaces of the shell and the conical nozzle but may vary linearly across the thickness. The thermal stress problem is converted to an equivalent boundary value problem and boundary conditions are specified at the junction of the spherical shell and conical nozzle. The stresses are obtained for a uniform increase in temperature and for a linear variation of temperature across the thickness of the shell, and are presented in graphical form for ready use.

A simple model for protein thermal denaturation

Whether proteins denature in all-or-none fashion or in a continuous fashion is as yet an unresolved problem. The all-or-none process implies that while the process of denaturation is going on, only two kinds of protein molecules can exist. One is completely unchanged and the other is altered. The altered protein molecules are indistinguishable. Underlying the 'continuum' models is the assumption that all the chains in a protein globule undergo similar changes so that it is enough to consider a single chain.

Studies on LDPE-cyanoethylated lignocellulosics blends using epoxy functionalized LDPE as compatibilizer

Rubberwood flour and cellulose have been plasticized by cyanoethylation and then blended with low-density polyethylene (LDPE). A small quantity of epoxy functionalized polyethylene i.e., polyethylene-co-glycidyl methacrylate (PEGMA) has been added to further enhance the mechanical properties. The mechanical properties were measured according to the standard ASTM methods. SEM analysis was performed for both fractured and unfractured blend specimens. The mechanical properties were improved by the addition of PEGMA compatibilizer. LDPE blends with cyanoethylated wood flour (CYWF) showed higher tensile strength and modulus than cyanoethylated cellulose CYC-LDPE blends. However CYC-LDPE blends exhibited higher relative elongation at break values as compared with the former. The TGA analysis showed lowering of thermal stability as the filler content is increased and degradation temperature of LDPE is shifted slightly to lower temperature. DSC analysis showed loss of crystallinity for the LDPE phase as the filler content is increased for both types of blends. Dielectric properties of the blends were similar to LDPE, but were lowered on adding PEGMA. (c) 2006 Wiley Periodicals, Inc.

Kinetics of TiO2-catalyzed ultrasonic degradation of rhodamine dyes

The ultrasonic degradation of two dyes, Rhodamine B (C28H31ClN2O3) and Rhodamine Blue (C28H32N2O3), were studied in the absence of catalyst and in the presence of two catalysts (combustion-synthesized anatase TiO2 and commercial Degussa P-25 TiO2. The rate of degradation of catalyzed reaction was higher than that obtained with in the absence of the catalysts. Among the catalysts, combustion-synthesized anatase TiO2 degraded the dyes faster when compared to the degradation with commercial Degussa P-25 catalyst. A Langmuir-Hinshelwood kinetic model was developed and the kinetic rate parameters were determined. The effect of other operating parameters, such as initial concentration, pH, temperature, and power intensity, was also investigated. The degradation rate increased with decreasing pH, increasing temperature, and higher intensity.

Thermal and photochemical cycloaddition reactions of thiocarbonyls: a qualitative molecular orbital analysis

A comprehensive analysis of thermal and photochemical reactions of thiocarbonyls has been undertaken within the PMO framework employing MINDO/3 orbital energies and wavefunctions. The model is generally successful in rationalizing the observed regiochemistry of such reactions. In particular, the indicated regiochemistry for [4 + 2] thermal cycloadditions of saturated thiones to 2-substituted dienes, for the dimerization of α,β-unsaturated thiones, and for the photochemical cycloadditions of thioketones and thioenones are all in agreement with experimental observations. Interesting predictions are also made concerning cycloadditions of saturated, conjugated, and arylalkyl thiones which have not yet been studied experimentally. The analysis reveals the decisive role played by secondary orbital interactions in determining the observed product selectivity in the photochemical reactions between thioenone and olefins.