Influence of pH on the retention of heavy metal ions by fly ash

Clay liners have been widely used to contain toxic and hazardous wastes. Clays adsorb the contaminant cations due to their exchange capacity. To improve the performance of the clay liner, fly ash, a waste material arising out of combustion of coal has been studied as a pre-filter material. The results indicate that fly ash has the potential to retain heavy metal ions. This study concerns the retention of zinc by fly ash. The influence of pH on retention as well as leaching characteristics are examined. The results obtained from the retention experiments by permeameter method indicate that fly ash retains the zinc ions through precipitation in the pores as well as onto the surface when the ambient pH value is more than 6.9, and only through adsorption when the pH value is less than 6.9. It has been observed that fly ash did not release the retained zinc ions when the pH value is between 3.5 and 10.0. Hence, the retention of zinc ions by fly ash is likely to be permanent since the pH of most of the landfill leachates are between 3.7 to 8.8.

Influence of poling methods on the orientational dynamics of 2-methyl-4-nitro-aniline in poly(methyl methacrylate) studied by second harmonic generation

The magnitude and stability of the induced dipolar orientation of 2-methyl-4-nitroaniline (MNA)/poly(methyl methacrylate) (PMMA) guest/host system is investigated. The chromophores are aligned using both the corona discharge and contact electrode poling techniques. The magnitude of order parameter (also an indicator for the second order nonlinear susceptibility) is measured by recording absorbances of the poled (by the two different techniques) and unpoled PMMA films at different concentrations of MNA. Under the same conditions the corona poling technique creates a higher alignment of molecules along the field direction. The time dependence of the second harmonic intensity of the MNA/PMMA film prepared by the two techniques can be described by a Kohlrausch-Williams-Watts stretched exponential. The temperature dependence of the decay time constant is found to generally follow a modified Williams-Landel-Ferry (WLF) or Vogel-Tamann-Fulcher (VTF) equation. The glass transition temperature seems to be the single most important parameter for determining the relaxation time tau(T).

Influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304 during hot working

The influence of strain rate and state-of-stress on the formation of ferrite in stainless steel type AISI 304L, 304 and 304 as-cast, during hot working has been studied. Compression and torsion tests were conducted in the temperature range 1100 to 1250 degrees C and strain rate range 0.001 to 100 s(-1) on these materials, Ferrite formation occurs during deformation at temperatures above 1150 degrees C and strain rates above 10 s(-1), in stainless steel type AISI 304L and 304. The tendency for the formation of ferrite is more in as-cast 304 than in wrought 304, In as-cast 304 the ferrite forms at lower temperatures and strain rates, The tendency for the ferrite formation is more in torsion than in compression.

Influence of glycosidic linkage on the nature of carbohydrate binding in beta-prism I fold lectins: An X-ray and molecular dynamics investigation on banana lectin-carbohydrate complexes

The three crystal structures reported here provide details of the interactions of mannose and the mannosyl-alpha-1,3-mannose component of a pentamannose with banana lectin and evidence for the binding of glucosyl-alpha-1,2-glucose to the lectin. The known structures involving the lectin include a complex with glucosyl-beta-1,3-glucose. Modeling studies on the three disaccharide complexes with the reducing end and the nonreducing end at the primary binding site are also provided here. The results of the Xray and modeling studies show that the disaccharides with an alpha-1,3 linkage prefer to have the nonreducing end at the primary binding site, whereas the reducing end is preferred at the site when the linkage is beta-1,3 in mannose/glucose-specific beta-prism I fold lectins. In the corresponding galactose-specific lectins, however, alpha-1,3-linked disaccharides cannot bind the lectin with the nonreducing end at the primary binding site on account of steric clashes with an aromatic residue that occurs only when the lectin is galactose-specific. Molecular dynamics simulations based on the known structures involving banana lectin enrich the information on lectin-carbohydrate interactions obtained from crystal structures. They demonstrate that conformational selection as well as induced fit operate when carbohydrates bind to banana lectin.

Solid-state photobehaviour and crystal packing of o-chlorobenzylidene-DL-piperitone: influence of molecular topology on photobehaviour

C17H19ClO, M(r) = 274.7, triclinic, P1BAR, a = 11.154 (3), b = 12.685 (2), c = 12.713 (2) angstrom, alpha = 100.68 (1), beta = 113.58 (1), gamma = 104.50 (2)-degrees, V = 1511.1 (6) angstrom3, Z = 4, D(m) = 1.22, D(x) = 1.215 Mg m-3, Cu K-alpha, lambda = 1.5418 angstrom, mu = 2.16 mm-1, F(000) = 584, T = 293 K, R = 0.057 for 3481 observed reflections. The title compound is photostable in the crystalline state and lattice-energy calculations have been employed to rationalize the photobehaviour. The well-known beta-steering ability of the chloro group is not operative in this system as there are no Cl...Cl interactions in the crystal lattice. All five benzylidene-DL-piperitone structures so far studied are alpha-packed and the molecular topology appears to be a deciding factor even in the presence of steering groups.

The influence of pH on the corrosion of medium strength aerospace alloys 8090, 2091 and 2014

The influence of pH on the corrosion behaviour of two aluminium-lithium-copper-magnesium-zirconium (8090 and 2091) alloys was studied and compared with a standard aircraft alloy, 2014 (Al-4.4% Cu) and 99.9% pure Al. In constant exposure and potentiodynamic polarization studies conducted in 3.5% NaCl solution having different pH values, all the alloys exhibited high corrosion rates in acidic and alkaline environments, with a minimum in less hostile environments close to neutral pH. The pitting potentials for aluminium-lithium alloys were slightly lower than those for 2014 and pure Al. The effect of pH on the passive current density was also less for aluminium-lithium alloys.

Influence of Alkali Ions in Enhancing the Nonlinearity of ZnO-Bi2O3-Co3O4 Varistor Ceramics

Zinc oxide ceramic varistors with simplified compositions of ZnO+Bi2O3+Co3O4+M(2)O (M=K or Na) show nonlinearity coefficients (alpha) of 40-75. The electron paramagnetic resonance spectra and optical reflectance spectra show that there is a direct interdependence between the oxidation state of transition metals and the alkali ions. The X-ray photoelectron spectra indicate that the alkali ions preserve a higher oxidation state of cobalt, Co(III), in the grain boundary regions than in the grain interiors having more Co(II). Admittance spectroscopy shows that, while the nature of traps remains unaltered, the trap density increases with the concentration of alkali ions near the interface. The observed defect states are associated with the grain bulk than with the grain boundary interfaces, as indicated by the isothermal capacitance transient signals

Influence of carbide particles on the dynamic recrystallization of as-cast 304 stainless steel: a study using secondary ion mass spectrometric (SIMS) analysis

The domain of dynamic recrystallization (DRX) in as-cast 304 stainless steel material occurs at higher temperatures (1250 degrees C) and lower strain rates (0.001 s(-1)) than in wrought 304 stainless steel (1100 degrees C and 0.01 s(-1)). The above result has been explained earlier on the basis of a simple theoretical DRX model involving the rate of nucleation versus rate of grain boundary migration. The present investigation is aimed at examining experimentally the influence of carbide particles on the DRX of ascast 304 using secondary ion mass spectrometric (SIMS) analysis. Isothermal compression tests at a constant true strain rate have been performed on wrought 304 and as-cast 304 materials in the temperature and strain rate ranges of 1000 to 1250 degrees C and 0.001 to 1 s(-1) respectively. The SIMS analysis carried out on the deformed samples revealed that the large carbides present in the as-cast 304 material strongly influence the DRX process. In as-cast 304 material, the presence of large carbide particles in the microstructure shifts the DRX domain to higher temperature and lower strain rate in comparison with wrought 304 material.

Influence of cadmium on lipid peroxidation and antioxidant enzymes in isolated rat hepatocytes

Cadmium (Cd) influences lipid peroxidation (LPO) by enhancing peroxidation of membrane lipids and by disturbing the antioxidant system of cells. In isolated rat hepatocytes, LPO was observed in cells incubated with Cd (50-250 mu M) for various time periods up to 90 min. The antioxidant enzymes such as superoxide dismutase (SOD) and catalase (CAT) were inhibited along with depletion of glutathione (GSH) in hepatocytes treated with Cd. The results show that Cd influences LPO in rat hepatocytes due to decrease in antioxidant status.

Influence of growth below and above T-c on the morphology and domain structure in flux-grown KTP crystals

KTP crystals have been grown below and above the ferroelectric transition temperature by flux method employing both spontaneous and top-seeded solution growth techniques. A slight morphological difference has been observed in these crystals when grown below and above the T-c. Ferroelectric domains are studied in these crystals by selective domain etching. It is seen that the ferroelectric domains in crystals grown spontaneously below T, show a complicated structure. A systematic investigation of the factors influencing domain structure has been carried out. Stress to some extent has been shown to affect the domain structure. Finally, a convenient way of converting the multidomain crystals into monodomain ones is described.

Influence of metalaxyl on Glomus fasciculatum associated with wheat (Triticum aestivum L)

Soil incorporation of metalaxyl [methyl N-(2-methoxyacetyl)-N-(2,6,xylyl)-DL-alaninate] significantly enhanced root colonization of the vesicular-arbuscular (VA) mycorrhizal fungi Glomus fasciculatum associated with wheat. The stimulatory response of VA mycorrhizal fungi to low concentration of metalaxyl resulted in increased plant biomass production, nutrient uptake and grain yield of wheat. However, higher concentrations of metalaxyl, particularly 2.5 ppm of metalaxyl affected the mycorrhizal infection and seed yield of wheat, Addition of urban compost to an extent ameliorated the toxic effect of fungicide on VA mycorrhizal colonization, plant growth and yield of wheat when compared to unamended soil.

Influence of the ferromagnetic layer on the pair breaking and low alternating current field magnetic response in superconductor/ferromagnet bilayer

We investigate the influence of the ferromagnetic layer on the magnetic and transport properties of YBa2Cu3O7-delta in YBa2Cu3O7-delta (YBCO)/La0.7Sr0.3MnO3 (LSMO) bilayers. The temperature dependent dc magnetization study reveals the presence of magnetic anisotropy in YBCO/LSMO bilayer as compared to the pure YBCO layer. The ac susceptibility study on YBCO/LSMO bilayers reveals stronger pinning and the temperature dependent critical current is found to be less prone to temperature. Besides, the current (I) dependent electrical transport studies on YBCO/LSMO exhibit a significant reduction in the superconducting T-c with increase in I and it follows I-2/3 dependence in accord with the pair breaking effect. The higher reduction of superconducting T-c in YBCO/LSMO is believed to be due to the enhanced pair-breaking induced by the spin polarized carriers being injected into the superconductor. (C) 2011 American Institute of Physics. doi: 10.1063/1.3560029]

Influence of foam/glass-epoxy interface on the macroscopic compressive failure features

The effect on the macroscopic compressive failure features of introduction of two flexible foam layers, either together at mid-region or separately at two locations that are away from the midregion, into a glass-epoxy (G-E) system is studied in this work. In this experimental approach an attempt to look at the possible influence the foam/G-E interface region has on the way the materials respond to compressive loading is made by involving an analyses of macrofractographic features. While foam-free samples fail by extensive ear formation and separation nearer to the mid-region, the foam bearing ones display pronounced interface separation. The positioning of the foam sheet(s) has a bearing on the failure features.