Tailoring texture of γ-Y2Si2O7 by strong magnetic field alignment and two-step sintering

In this study, a well-dispersed γ-Y2Si2O 7 ethanol-based suspension with 30 vol% solid loading was prepared by adding 1 dwb% polyethylene imine dispersant, which allows feeble magnetic γ-Y2Si2O7 particles with anisotropic magnetic susceptibility to rotate in a 12 T strong magnetic field during slip casting, resulting in the development of a strong texture in green bodies. Pressureless sintering gives rise to more pronounced grain growth in the textured sample than in the untextured sample prepared without the magnetic field due to the rapid migration of the grain boundaries of the well-oriented grains, which was revealed by constant-heating-rate sintering kinetics. It was found that the use of two-step sintering is very efficient not only for inhibiting the grain growth but also for enhancing the texture. This implies that controlled grain growth is crucial for enhancing texture development in γ-Y2Si2O7.

A numerical study of the effect of loading conditions on tubular hydroforming

In this work, the mechanics of tubular hydroforming under various types of loading conditions is investigated. The main objective is to contrast the effects of prescribing fluid pressure or volume flow rate, in conjunction with axial displacement, on the stress and strain histories experienced by the tube and the process of bulging. To this end, axisymmetric finite element simulations of free hydroforming (without external die contact) of aluminium alloy tubes are carried out. Hill’s normally anisotropic yield theory along with material properties determined in a previous experimental study [A. Kulkarni, P. Biswas, R. Narasimhan, A. Luo, T. Stoughton, R. Mishra, A.K. Sachdev, An experimental and numerical study of necking initiation in aluminium alloy tubes during hydroforming, Int. J. Mech. Sci. 46 (2004) 1727–1746] are employed in the computations. It is found that while prescribed fluid pressure leads to highly non-proportional strain paths, specified fluid volume flow rate may result in almost proportional ones for the predominant portion of loading. The peak pressure increases with axial compression for the former, while the reverse trend applies under the latter. The implication of these results on failure by localized necking of the tube wall is addressed in a subsequent investigation.

Individual variation in in vitro efficacy of antiplatelet medication - aspirin and clopidogrel

Antiplatelet medication is known to decrease adverse effects in patients with atherothrombotic disease. However, despite ongoing antiplatelet medication considerable number of patients suffer from atherothrombotic events. The aims of the study were 1) to evaluate the individual variability in platelet functions and compare the usability of different methods in detecting it, 2) to assess variability in efficacy of antiplatelet medication with aspirin (acetylsalicylic acid) or the combination of aspirin and clopidogrel and 3) to investigate the main genetic and clinical variables as well as potential underlying mechanisms of variability in efficacy of antiplatelet medication. In comparisons of different platelet function tests in 19 healthy individuals PFA-100® correlated with traditional methods of measuring platelet function and was thus considered appropriate for testing individual variability in platelet activity. Efficacy of ongoing 100mg aspirin daily was studied in 101 patients with coronary artery disease (CAD). Aspirin response was measured with arachidonic acid (AA)-induced platelet aggregation, which reflects cyclo-oxygenase (COX)-1 dependent thromboxane (Tx) A2 formation, and PFA-100®, which evaluates platelet activation under high shear stress in the presence of collagen and epinephrine. Five percent of patients failed to show inhibition of AA-aggregation and 21% of patients had normal PFA-100® results despite aspirin and were thus considered non-responders to aspirin. Interestingly, the two methods of assessing aspirin efficacy, platelet aggregation and PFA-100®, detected different populations as being aspirin non-responders. It could be postulated that PFA-100® actually measures enhanced platelet function, which is not directly associated with TxA2 inhibition exerted by aspirin. Clopidogrel efficacy was assessed in 50 patients who received a 300mg loading dose of clopidogrel 2.5 h prior to percutaneous coronary intervention (PCI) and in 51 patients who were given a loading dose of 300mg combined with a five day treatment of 75mg clopidogrel daily mimicking ongoing treatment. Clopidogrel response was assessed with ADP-induced aggregations, due to its mechanism of action as an inhibitor of ADP-induced activation. When patients received only a loading dose of clopidogrel prior to PCI, 40% did not gain measurable inhibition of their ADP-induced platelet activity (inhibition of 10% or less). Prolongation of treatment so that all patients had reached a plateau of inhibition exerted by clopidogrel, decreased the incidence of non-responders to 20%. Polymorphisms of COX-1 and GP VI, as well as diabetes and female gender, were associated with decreased in vitro aspirin efficacy. Diabetes also impaired the in vitro efficacy of short-term clopidogrel. Decreased response to clopidogrel was associated with limited inhibition by ARMX, an antagonist of P2Y12-receptor, suggesting the reason for clopidogrel resistance to be receptor-dependent. Conclusions: Considerable numbers of CAD patients were non-responders either to aspirin, clopidogrel or both. In the future, platelet function tests may be helpful to individually select effective and safe antiplatelet medication for these patients.

Electrokinetic and Rheological Properties of Nano Zirconia in the Presence of Rhamnolipid Biosurfactant

In this paper, the effect of rhamnolipid biosurfactant on the electrokinetic and rheological behavior of nanozirconia particles is reported. The effect of pH, concentration of biosurfactant, and solids loading on ζ-potential and rheological behavior was investigated. ζ-potential measurements showed that adsorption of biosurfactant shifted the iso-electric point of zirconia with increasing biosurfactant concentration. The surface of zirconia became more electronegative in the presence of biosurfactant indicating a strong interaction. Maximum charge was obtained in the presence of about 230 ppm of biosurfactant. Rheological tests at pH 7 revealed that the zirconia suspension is viscous at high solids loading and addition of biosurfactant decreased the viscosity substantially especially at high solids loading (>50 wt%). Sedimentation tests confirmed that the biosurfactant is a good dispersant for zirconia particles at pH values of 7 and above.

Clinical Phenotype and Genetic Epidemiology of Schizophrenia in a Finnish Isolate

This study is part of the joint project "The Genetic Epidemiology and Molecular Genetics of schizophrenia in Finland" between the Departments of Mental Health and Alcohol Research, and Molecular Medicine at the National Public Health Institute. In the study, we utilized three nationwide health care registers: 1) the Hospital Discharge Register, 2) the Free Medication Register, and 3) the Disability Pension Register, plus the National Population Register, in order to identify all patients with schizophrenia born from 1940 to 1976 (N=33,731) in Finland, and their first degree-relatives. 658 patients with at least one parent born in a homogeneous isolate in northeastern Finland were identified, as well as 4904 familial schizophrenia patients with at least two affected siblings from the whole country. The comparison group was derived from the Health 2000 Study. We collected case records and reassessed the register diagnosis. Were contacted the isolate patients and a random sample of patients from the whole country to make diagnostic clinical interviews and to assess the negative and positive symptoms and signs of schizophrenia. In addition to these patients, we interviewed siblings who were initially healthy according to the Hospital Discharge Register. Of those with a register diagnosis of schizophrenia, schizoaffective or schizophreniform disorder, 69% received a record-based consensus diagnosis and 63% an interview-based diagnosis of schizophrenia. Patients with schizophrenia having first-degree relatives with psychotic disorder had more severe affective flattening and alogia than those who were the only affected individuals in their family. The novel findings were: 1) The prevalence of schizophrenia in the isolate was relatively high based on register (1.5%), case record (0.9-1.3%), and interview (0.7-1.2%) data. 2) Isolate patients, regardless of their familial loading for schizophrenia, had less delusions and hallucinations than the whole country familial patients, which may be related to the genetic homogeneity in the isolate. This phenotype encourages the use of endophenotypes in genetic analyses instead of diagnoses alone. 3) The absence of register diagnosis does not confirm that siblings are healthy, because 7.7% of siblings had psychotic symptoms already before the register diagnoses were identified in 1991. For genetic research, the register diagnosis should therefore be reassessed using either a structured interview or a best- estimate case note consensus diagnosis. Structured clinical interview methods need be considered also in clinical practice.

Experimental study on behaviour of concrete filled double skin tube columns under lateral impact loading

This paper presents an experimental investigation on the lateral impact response of axially loaded concrete filled double skin tube (CFDST) columns. A total of four test series are being conducted at Queensland University of Technology using a novel horizontal impact-testing rig. The test results reported in this paper are from the first test series, where the columns are pinned at both ends and impacted at mid-span. In the next three series, effects of support conditions, impact location and repeated impact will be treated. The main objectives of the current paper are to describe the innovative testing procedure and provide some insight into the lateral impact behavior and failure of simply supported axially pre-loaded CFDST columns. The results include time histories of impact forces, reaction forces, axial force and global lateral deflection. Based on the test data, the failure mode, peak impact force, peak reaction forces, maximum deflection and residual deflection, with and without axial load, are analyzed and discussed. The findings of this study will serve as a benchmark reference for future analysis and design of CFDST columns.

Impact resistance and evaluation of retained strength on geotextiles

Over the last few decades, geotextiles have progressively been incorporated into geotechnical applications, especially in the field of coastal engineering. Geotextile materials often act as separator and a filter layer between rocks laid above and subgrade beneath. This versatile material has gradually substituted traditional granular materials because of its ease of installation, consistent quality and labour costefficiency. However, geotextiles often suffer damage during installation due to high dynamic bulk loading of rock placement. This can degrade geotextiles' mechanical strength. The properties considered in this paper include the impact resistance and retained strength of geotextiles. In general, the greater the impact energy applied to geotextiles, the greater the potential for damage. Results highlight the inadequacy of using index derived values as an indicator to determine geotextile performance on site because test results shows that geotextiles (staple fibre (SF) and continuous filament (CF)) with better mechanical properties did not outperform lower mechanical strength materials. The toughest CF product with a CBR index value of 9696N shows inferior impact resistance compared to SF product with the least CBR strength (2719N) given the same impact energy of 9.02 kJ. Test results also indicated that the reduction of strength for CF materials were much greater (between 20 and 50%) compared to SF materials (between 0 and 5%) when subjected to the same impact energy of 4.52 kJ.

The effect of ageing on microstructure and nanoindentation behaviour of dc magnetron sputter deposited nickel rich NiTi films

Nickel rich NiTi films were sputter deposited on p-doped Si left angle bracket1 0 0right-pointing angle bracket substrates maintained at 300 °C. The films were subsequently solution treated at 700 °C for 30 min followed by ageing at 400 and 500 °C for 5 h. The microstructure of the films was examined by TEM and these studies revealed that the NiTi films were mostly amorphous in the as-deposited condition. The subsequent solution treatment and ageing resulted in crystallization of the films with the film aged at 400 °C exhibiting nanocrystalline grains and three phases viz. B2 (austenite), R and Ni3Ti2 whereas the film aged at 500 °C shows micron sized grains and two phases viz. R and Ni3Ti2. Nanoindentation studies revealed that the nature of the load versus indentation depth response for the films aged at 400 and 500 °C was different. For the same load, the indenter penetrated to a much greater depth for the film aged at 400 °C as compared to the film aged at 500 °C. Also the ratio of the residual indentation depth (hf) to maximum indentation depth (hmax) is lower for the film aged at 400 °C as compared to the film aged at 500 °C. This was attributed to the occurrence of stress induced martensitic transformation of the B2 phase present in the film aged at 400 °C during indentation loading which results in a transformation strain in addition to the normal elastic and plastic strains and its subsequent recovery on unloading. The hardness and elastic modulus measured using the Oliver and Pharr analysis was also found to be lower for the film aged at 400 °C as compared to the film aged at 500 °C which was also primarily attributed to the same effect.

Prediction of fatigue strength in plain and reinforced concrete beams

A fatigue crack propagation model for concrete is proposed based on the concepts of fracture mechanics. This model takes into account the loading history, frequency of applied load, and size, effect parameters. Using this model, a method is described based on linear elastic fracture mechanics to assess the residual strength of cracked plain and reinforced concrete (RC) beams. This could be used to predict the residual strength (load carrying capacity) of cracked or damaged plain and reinforced concrete beams at a given level of damage. It has been seen that the fatigue crack propagation rate increases as. the size of plain concrete, beam increases indicating an increase in brittleness. In reinforced concrete (RC) beams, the fracture process becomes stable only when the beam is sufficiently reinforced.

Preparation, characterization and electrical conductivity studies of MWCNT/ZnO nanoparticles hybrid

Multiwall carbon nanotubes (MWCNTs) were decorated with crystalline zinc oxide nanoparticles (ZnO NPs) by wet chemical route to form MWCNT/ZnO NPs hybrid. The hybrid sample was characterized by scanning and transmission electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. Electrical conductivity of the hybrid can be tuned by varying the ZnO NPs content in the hybrid. In order to investigate the effect of nanoparticles loading on the conduction of MWCNTs network, electrical conductivity studies have been carried out in the wide temperature range 1.5-300K. The electrical conductivity of the hybrid below 100K is explained with the combination of variable range hopping conduction and thermal fluctuation induced tunnelling model. (C) 2009 Elsevier B.V. All rights reserved.

Diffusion of Pure CH4 and Its Binary Mixture with CO2 in Faujasite NaY: A Combination of Neutron Scattering Experiments and Molecular Dynamics Simulations

The self-diffusion properties of pure CH4 and its binary mixture with CO2 within MY zeolite have been investigated by combining an experimental quasi-elastic neutron scattering (QENS) technique and classical Molecular dynamics simulations. The QENS measurements carried out at 200 K led to an unexpected self-diffusivity profile for Pure CH4 with the presence of a maximum for a loading of 32 CH4/unit cell, which was never observed before for the diffusion of apolar species in azeolite system With large windows. Molecular dynamics simulations were performed using two distinct microscopic models for representing the CH4/NaY interactions. Depending on the model, we are able to fairly reproduce either the magnitude or the profile of the self-diffusivity.Further analysis allowed LIS to provide some molecular insight into the diffusion mechanism in play. The QENS measurements report only a slight decrease of the self-diffusivity of CH4 in the presence of CO2 when the CO2 loading increases. Molecular dynamics simulations successfully capture this experimental trend and suggest a plausible microscopic diffusion mechanism in the case of this binary mixture.

Strength design of composite beam using gradient and particle swarm optimization

This work addresses the optimum design of a composite box-beam structure subject to strength constraints. Such box-beams are used as the main load carrying members of helicopter rotor blades. A computationally efficient analytical model for box-beam is used. Optimal ply orientation angles are sought which maximize the failure margins with respect to the applied loading. The Tsai-Wu-Hahn failure criterion is used to calculate the reserve factor for each wall and ply and the minimum reserve factor is maximized. Ply angles are used as design variables and various cases of initial starting design and loadings are investigated. Both gradient-based and particle swarm optimization (PSO) methods are used. It is found that the optimization approach leads to the design of a box-beam with greatly improved reserve factors which can be useful for helicopter rotor structures. While the PSO yields globally best designs, the gradient-based method can also be used with appropriate starting designs to obtain useful designs efficiently. (C) 2006 Elsevier Ltd. All rights reserved.

Interface stresses in a composite cylindrical shell under ring loading

The problem of a two-layer circular cylindrical shell subjected to radial ring loading has been solved theoretically. The solution is developed by uniting the elasticity solution through Love function approach for the inner thick shell with the Flügge shell theory for the thin outer shell. Numerical work has been done with a digital computer for different values of shell geometry parameters and material constants. The general behaviour of the composite shell has been studied in the light of these numerical results.

Ring loading of a long, thin, circular cylindrical shell enclosing a soft, solid core: A recalculation by the love function method of elasticity.

The problem is solved using the Love function and Flügge shell theory. Numerical work has been done with a computer for various values of shell geometry parameters and elastic constants.

Mechanical and Thermal Properties of Eva Blended with Biodegradable Ethyl Cellulose

In this study, biodegradable blend of Poly (Ethylene-co-Vinyl Acetate) (EVA) and Ethyl Cellulose (EC) were prepared. Ethylene vinyl alcohol (EVOH) copolymer was used as an interfacial compatibilizer to enhance adhesion between EVA and EC. The melt blended compatibilized biocomposites were examined for mechanical and thermal properties as per the ASTM standards. It has been found that the EC has a reinforcing effect on EVA leading to enhanced tensile strength and also impart biodegradability. Thus, a high loading of 50% EC could be added without compromising Much on the mechanical properties. Analysis of the tensile data using predictive theories showed an enhanced interaction of the dispersed phase (EC) and the matrix (EVA). The compatibilizing effects of EVOH on these blends were confirmed by the significant improvement in the mechanical properties comparable with neat EVA as also observed by SEM microscopy. The TGA thermograms exhibits two-stage degradation and as EC content increases, the onset temperature for thermal degradation reduces. (C) 2009 Wiley Periodicals, Inc. J Appl Polym Sci 116: 1044-1056, 2010