Characterization of residential chimney conditions for flue gas flow measurements

A literature survey and a theoretical study were performed to characterize residential chimney conditions for flue gas flow measurements. The focus is on Pitot-static probes to give sufficient basis for the development and calibration of a velocity pressure averaging probe suitable for the continuous dynamic (i.e. non steady state) measurement of the low flow velocities present in residential chimneys. The flow conditions do not meet the requirements set in ISO 10780 and ISO 3966 for Pitot-static probe measurements, and the methods and their uncertainties are not valid. The flow velocities in residential chimneys from a heating boiler under normal operating condi-tions are shown to be so low that they in some conditions result in voiding the assumptions of non-viscous fluid justifying the use of the quadratic Bernoulli equation. A non-linear Reynolds number dependent calibration coefficient that is correcting for the viscous effects is needed to avoid significant measurement errors. The wide range of flow velocity during normal boiler operation also results in the flow type changing from laminar, across the laminar to turbulent transition region, to fully turbulent flow, resulting in significant changes of the velocity profile during dynamic measurements. In addition, the short duct lengths (and changes of flow direction and duct shape) used in practice are shown to result in that the measurements are done in the hydrodynamic entrance region where the flow velocity profiles most likely are neither symmetrical nor fully developed. A measurement method insensitive to velocity profile changes is thus needed, if the flow velocity profile cannot otherwise be determined or predicted with reasonable accuracy for the whole measurement range. Because of particulate matter and condensing fluids in the flue gas it is beneficial if the probe can be constructed so that it can easily be taken out for cleaning, and equipped with a locking mechanism to always ensure the same alignment in the duct without affecting the calibration. The literature implies that there may be a significant time lag in the measurements of low flow rates due to viscous effects in the internal impact pressure passages of Pitot probes, and the significance in the discussed application should be studied experimentally. The measured differential pressures from Pitot-static probes in residential chimney flows are so low that the calibration and given uncertainties of commercially available pressure transducers are not adequate. The pressure transducers should be calibrated specifically for the application, preferably in combination with the probe, and the significance of all different error sources should be investigated carefully. Care should be taken also with the temperature measurement, e.g. with averaging of several sensors, as significant temperature gradients may be present in flue gas ducts.

Online and Offline Gaming as Support for English Education in Swedish Upper Elementary Schools with Focus on Reading Comprehension Online and Offline Gaming as Support for English Education in Swedish Upper Elementary Schools with Focus on Reading Comprehension : A literature review about online and offline gaming as a resource for developing English reading comprehension in Swedish schools in year 4-6

The aim of this degree thesis is to see what research says about the use of computer and video games to support upper elementary pupils’ development in English reading comprehension in Swedish schools. Other goals are to see how online and offline gaming can be integrated in the Swedish schools and what attitudes teachers have towards gaming. The method used is a systematic literature review and the purpose is to analyze chosen articles and to find relevant content that answers the research questions. Five articles were chosen from different databases and were systematically analyzed in this thesis. The results show that online gaming as support for education can be rewarding for some upper elementary pupils in English learning. However, in English reading comprehension there is not much research found which means that more research needs to be made within this area. Moreover, involving online gaming in English language learning seems to be a challenge for teachers mostly because of their lack of knowledge about the subject, even though they are positive to gaming. The lack of knowledge about the subject could be altered with more education and courses in the area.

Teaching grammar: A study of the common English grammar errors and grammar teaching methods that can be relevant for Swedish upper secondary schools

Grammar has always been an important part of language learning. Based on various theories, such as the universal grammar theory (Chomsky, 1959) and, the input theory (Krashen, 1970), the explicit and implicit teaching methods have been developed. Research shows that both methods may have some benefits and disadvantages. The attitude towards English grammar teaching methods in schools has also changed and nowadays grammar teaching methods and learning strategies, as a part of language mastery, are one of the discussion topics among linguists. This study focuses on teacher and learner experiences and beliefs about teaching English grammar and difficulties learners may face. The aim of the study is to conduct a literature review and to find out what scientific knowledge exists concerning the previously named topics. Along with this, the relevant steering documents are investigated focusing on grammar teaching at Swedish upper secondary schools. The universal grammar theory of Chomsky as well as Krashen’s input hypotheses provide the theoretical background for the current study. The study has been conducted applying qualitative and quantitative methods. The systematic search in four databases LIBRIS, ERIK, LLBA and Google Scholar were used for collecting relevant publications. The result shows that scientists’ publications name different grammar areas that are perceived as problematic for learners all over the world. The most common explanation of these difficulties is the influence of learner L1. Research presents teachers’ and learners’ beliefs to the benefits of grammar teaching methods. An effective combination of teaching methods needs to be done to fit learners’ expectations and individual needs. Together, they will contribute to the achieving of higher language proficiency levels and, therefore, they can be successfully applied at Swedish upper secondary schools.

Emissions Characterisation of residential pellet boilers during start-up and stop periods

In this study, gaseous emissions and particles are measured during start-up and stop periods for an over-fed boiler and an under-fed boiler. Both gaseous and particulate matter emissions are continuously measured in the laboratory. The measurement of gaseous emissions includes oxygen (O2), carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxide and (NO). The emissions rates are calculated from measured emissions concentrations and flue gas flow. The behaviours of the boilers during start-up and stop periods are analysed and the emissions are characterised in terms of CO, NO, TOC and particles (PM2.5 mass and number). The duration of the characterised periods vary between two boilers due to the difference in type of ignition and combustion control. The under-fed boiler B produces higher emissions during start-up periods than the over-fed boiler A. More hydrocarbon and particles are emitted by the under-fed boiler during stop periods. Accumulated mass of CO and TOC during start-up and stop periods contribute a major portion of the total mass emitted during whole operation. However, accumulated mass of NO and PM during start-up and stop periods are not significant as the duration of emission peak is relatively short.

EMISSIONS CHARACTERISTICS OF A RESIDENTIAL PELLET BOILER AND A STOVE

Gaseous and particulate emissions from a residential pellet boiler and a stove are measured at a realistic 6-day operation sequence and during steady state operation. The aim is to characterize the emissions during each phase in order to identify when the major part of the emissions occur to enable actions for emission reduction where the savings can be highest. The characterized emissions comprised carbon monoxide (CO), nitrogen oxide (NO), total organic carbon (TOC) and particulate matter (PM 2.5). In this study, emissions were characterised by mass concentration and emissions during start-up and stop phases were also presented in accumulated mass. The influence of start-up and stop phases on the emissions, average emission factors for the boiler and stove were analysed using the measured data from a six-days test. The share of start-up and stop emissions are significant for CO and TOC contributing 95% and 89% respectively at the 20kW boiler and 82% and 89% respectively at the 12 kW stove. NO and particles emissions are shown to dominate during stationary operation.

English-medium instruction in Sweden : Perspectives and practices in two upper secondary schools

This thesis presents English-medium instruction (EMI) in the Swedish context, focusing on perspectives and practices in two schools. The research question is as follows: How and why is EMI offered, chosen, and practiced in the Swedish upper secondary school today? The aim is to explore the status of the educational option, the reasons for offering EMI to stakeholders, the stakeholders’ beliefs about and goals of EMI, and the implementation of EMI in the classroom. A survey of all upper secondary schools in Sweden was conducted to ascertain the spread of content teaching through a foreign language. The educational context was studied from an ecological perspective using methods based in linguistic ethnography. Language alternation, academic language, and language hierarchy were all considered. Interviews were analysed for content; and classroom language use was analysed for language choice and function. The concepts of affordance and scaffolding together with translanguaging were key. The de facto policies of the micro contexts of the schools were examined in light of the declared national policy of the macro context of Sweden. The results indicate that the option in Swedish schools has not increased, and also tends to only be EMI—not Content and Language Integrated Learning (CLIL) or instruction through other languages. EMI is offered for prestige, an international profile, marketing potential and personal interest. EMI students are academically motivated and confident, and see the option as “fun”. 100% EMI in the lessons is not the goal or the practice. Translanguaging is abundant, but how language alternation is perceived as an affordance or not differs in the two schools. One focuses on how the languages are used while the other focuses on how much each language is used. In conclusion, the analysis suggests that a development of definitions and practices of EMI in Sweden is needed, especially in relation to language policy and language hierarchy.

Energy efficient and economic renovation of residential buildings with low-temperature heating and air heat recovery

With the building sector accounting for around 40% of the total energy consumption in the EU, energy efficiency in buildings is and continues to be an important issue. Great progress has been made in reducing the energy consumption in new buildings, but the large stock of existing buildings with poor energy performance is probably an even more crucial area of focus. This thesis deals with energy efficiency measures that can be suitable for renovation of existing houses, particularly low-temperature heating systems and ventilation systems with heat recovery. The energy performance, environmental impact and costs are evaluated for a range of system combinations, for small and large houses with various heating demands and for different climates in Europe. The results were derived through simulation with energy calculation tools. Low-temperature heating and air heat recovery were both found to be promising with regard to increasing energy efficiency in European houses. These solutions proved particularly effective in Northern Europe as low-temperature heating and air heat recovery have a greater impact in cold climates and on houses with high heating demands. The performance of heat pumps, both with outdoor air and exhaust air, was seen to improve with low-temperature heating. The choice between an exhaust air heat pump and a ventilation system with heat recovery is likely to depend on case specific conditions, but both choices are more cost-effective and have a lower environmental impact than systems without heat recovery. The advantage of the heat pump is that it can be used all year round, given that it produces DHW. Economic and environmental aspects of energy efficiency measures do not always harmonize. On the one hand, lower costs can sometimes mean larger environmental impact; on the other hand there can be divergence between different environmental aspects. This makes it difficult to define financial subsidies to promote energy efficiency measures.

Emissions from realistic operation of residential wood pellets heating systems

Emissions from residential combustion appliances vary significantly depending on the firing behaviours and combustion conditions, in addition to combustion technologies and fuel quality. Although wood pellet combustion in residential heating boilers is efficient, the combustion conditions during start-up and stop phases are not optimal and produce significantly high emissions such as carbon monoxide and hydrocarbon from incomplete combustion. The emissions from the start-up and stop phases of the pellet boilers are not fully taken into account in test methods for ecolabels which primarily focus on emissions during operation on full load and part load. The objective of the thesis is to investigate the emission characteristics during realistic operation of residential wood pellet boilers in order to identify when the major part of the annual emissions occur. Emissions from four residential wood pellet boilers were measured and characterized for three operating phases (start-up, steady and stop). Emissions from realistic operation of combined solar and wood pellet heating systems was continuously measured to investigate the influence of start-up and stop phases on total annual emissions. Measured emission data from the pellet devices were used to build an emission model to predict the annual emission factors from the dynamic operation of the heating system using the simulation software TRNSYS. Start-up emissions are found to vary with ignition type, supply of air and fuel, and time to complete the phase. Stop emissions are influenced by fan operation characteristics and the cleaning routine. Start-up and stop phases under realistic operation conditions contribute 80 – 95% of annual carbon monoxide (CO) emission, 60 – 90% total hydrocarbon (TOC), 10 – 20% of nitrogen oxides (NO), and 30 – 40% particles emissions. Annual emission factors from realistic operation of tested residential heating system with a top fed wood pelt boiler can be between 190 and 400 mg/MJ for the CO emissions, between 60 and 95 mg/MJ for the NO, between 6 and 25 mg/MJ for the TOC, between 30 and 116 mg/MJ for the particulate matter and between 2x10-13 /MJ and 4x10-13 /MJ for the number of particles. If the boiler has the cleaning sequence with compressed air such as in boiler B2, annual CO emission factor can be up to 550 mg/MJ. Average CO, TOC and particles emissions under realistic annual condition were greater than the limits values of two eco labels. These results highlight the importance of start-up and stop phases in annual emission factors (especially CO and TOC). Since a large or dominating part of the annual emissions in real operation arise from the start-up and stop sequences, test methods required by the ecolabels should take these emissions into account. In this way it will encourage the boiler manufacturers to minimize annual emissions. The annual emissions of residential pellet heating system can be reduced by optimizing the number of start-ups of the pellet boiler. It is possible to reduce up to 85% of the number of start-ups by optimizing the system design and its controller such as switching of the boiler pump after it stops, using two temperature sensors for boiler ON/OFF control, optimizing of the positions of the connections to the storage tank, increasing the mixing valve temperature in the boiler circuit and decreasing the pump flow rate. For 85 % reduction of start-ups, 75 % of CO and TOC emission factors were reduced while 13% increase in NO and 15 % increase in particle emissions was observed.

Are schools able to bring sense into pupils' lives? - an experiment to use Antonovsky's concept sense of coherence from a school perspective. : Paper presented at the ENIRDEM conference in Kilkenny, Ireland 26th-29th September, 2002

Young people now spend a longer and longer period of their lives at school then ever before. Not always because that they want to, but because society has nothing else to offer. The situation in many schools may also, in different aspects, be seen as highly problematic. Andersson (2001) has, for example, found in a large longitudinal study - The Life Project – that schools seem to be adapted to the needs of only a minority of the students - around 30%. On the other hand school is badly adjusted to the requirements of another 30 %. This group of students often find school meaningless, uninteresting and boring. For these students school is mostly a waste of time. In such circumstances, it seems natural that society has a responsibility to offer young people a meaningful time at school, both here and now and to prepare them for a future live as adults, not only as a part of the work force.As a part of departure I briefly describe the model that Antonovsky has developed and try to use it in a school context instead. I have here, of course, no possibility to make a deeper analysis of a complex problem such as this.In Antonovsky’s spirit, using a salutogenic perspective, instead of asking ourselves why do pupils fail or perhaps also not like being at school we have to ask, instead: What it is that makes pupils successful? From this background the purpose of this paper is to discuss some aspects of how pupils may use different strategies to handle their school situation in a proper way.

"Magistrander" teachers linking schools and university : experiences from the University of Dalarna, Sweden

For some time, a debate has been going on in Sweden on how to link schools and universities to create more efficient and mutually beneficial co-operation. A pilot scheme at the University of Dalarna, financed by the State and local authorities, has created special posts for teachers allowing them to work part time in school and part time at the university. The teachers involved become “magistrander”, post-graduate students working towards a Master’s degree. Initiatives of this type raise some important questions:• What impact, if any, does this type of programme have on teachers’ skills and on activities taking place in schools?• Does it affect courses and research at the university taking part in this co-operation?The purpose of this paper is to discuss expectations and results based on experiences from the University of Dalarna.

Degree projects improving co-operation between the teacher education program and schools : - Swedish experiences

In 1977, when teacher education inSwedenwas incorporated into the university system, the main reason was to transform it into an academic tradition. Now, nearly 30 years later, there is still tension between the academic and the vocational tradition; they show up as different and separated elements in a program that is meant to prepare students for a career as a teacher and for a possible future career as a researcher in this field. This tension gives rise to a risk of allowing parallel “tracks” to develop and of isolating the degree thesis work from other courses. On the teacher-training program in which we are involved, close co-operation with partner-schools, where the practical part of the program takes place, has been established. Here, the students´ degree theses are an important factor in making this co-operation work on a concrete level. Accordingly, the purpose of the degree thesis is both to reflect problems in schools and contribute to better teaching in the individual school, but also to offer relevant educational subject matter to the students, which may be adapted as an element in the university’s research environments. From these points of view, the degree thesis is an important part of teacher education and rather more than just a single course. The degree thesis should be an element that gives the students an opportunity to show that they have reached central goals in the teacher education program. It should also be an integral part in the development of critical and scholarly thinking, deepening pedagogical and didactic knowledge and giving the students an opportunity to apply research methods. We will here use two minor case studies: one that compares teacher education programs in five Swedish universities and one minor study at one of those universities, in order to elaborate on the questions: - What purpose has a degree thesis and what role does it play in teacher education? - What criteria are relevant to assessing a degree thesis and what qualities do the degree theses have? - Is it possible to assess a degree thesis fairly and what happens to students who do not pass? - How could the degree thesis be used to improve the contact between the teacher education program and its partner schools in order to contribute to the development of the individual school?

Do inspections of schools influence head teachers’ leadership?

This paper seeks to describe and discuss the impact of inspections of schools in Sweden. It outlines the political context, based on New Public Management (NPM) theory, according to what role the Schools Inspectorate is supposed to play in order to govern and control. Attention is also devoted, referring an on-going case study, to how inspections influence head teachers and their leadership in their everyday work.   Reports from the Schools inspectorate are public. This forces both politicians and head teachers to take measures. In this case, the head teachers perceived that the inspection reports confirmed what they already knew, but it also gave them an alibi and a tool to push their teachers to take part in everyday school development work. During the first year after the inspection the head teachers mainly strived to adjust formal deficiencies in local steering documents. However, some of the deviations reported from the Schools inspectorate are regarding pedagogical problems that are complicated and difficult to handle. As interventions in many cases will show up much later the results are, for example as increased goal fulfilment, in this case, still an open question. Nevertheless, it seems obvious that the Schools Inspectorate must be seen as a result of the governing philosophy that denotes New Public Management NPM).

Assessing the physical environment of older people’s residential care facilities: development of the Swedish version of the Sheffield Care Environment Assessment Matrix (S-SCEAM)

Background There is emerging evidence that the physical environment is important for health, quality of life and care, but there is a lack of valid instruments to assess health care environments. The Sheffield Care Environment Assessment Matrix (SCEAM), developed in the United Kingdom, provides a comprehensive assessment of the physical environment of residential care facilities for older people. This paper reports on the translation and adaptation of SCEAM for use in Swedish residential care facilities for older people, including information on its validity and reliability. Methods SCEAM was translated into Swedish and back-translated into English, and assessed for its relevance by experts using content validity index (CVI) together with qualitative data. After modification, the validity assessments were repeated and followed by test-retest and inter-rater reliability tests in six units within a Swedish residential care facility that varied in terms of their environmental characteristics. Results Translation and back translation identified linguistic and semantic related issues. The results of the first content validity analysis showed that more than one third of the items had item-CVI (I-CVI) values less than the critical value of 0.78.  After modifying the instrument, the second content validation analysis resulted in I-CVI scores above 0.78, the suggested criteria for excellent content validity. Test-retest reliability showed high stability (96% and 95% for two independent raters respectively), and inter-rater reliability demonstrated high levels of agreement (95% and 94% on two separate rating occasions). Kappa values were very good for test-retest (κ= 0.903 and 0.869) and inter-rater reliability (κ= 0.851 and 0.832). Conclusions Adapting an instrument to a domestic context is a complex and time-consuming process, requiring an understanding of the culture where the instrument was developed and where it is to be used. A team, including the instrument’s developers, translators, and researchers is necessary to ensure a valid translation and adaption. This study showed preliminary validity and reliability evidence for the Swedish version (S-SCEAM) when used in a Swedish context. Further, we believe that the S-SCEAM has improved compared to the original instrument and suggest that it can be used as a foundation for future developments of the SCEAM model.