The Cup Anemometer, a Fundamental Meteorological Instrument for the Wind Energy Industry. Research at the IDR/UPM Institute

The results of several research campaigns investigating cup anemometer performance carried out since 2008 at the IDR/UPM Institute are included in the present paper. Several analysis of large series of calibrations were done by studying the effect of the rotor’s geometry, climatic conditions during calibration, and anemometers’ ageing. More specific testing campaigns were done regarding the cup anemometer rotor aerodynamics, and the anemometer signals. The effect of the rotor’s geometry on the cup anemometer transfer function has been investigated experimentally and analytically. The analysis of the anemometer’s output signal as a way of monitoring the anemometer status is revealed as a promising procedure for detecting anomalies.

Wind tunnel analysis of the aerodynamic loads on rolling stock over railway embankments: the effect of shelter windbreaks

Wind-flow pattern over embankments involves an overexposure of the rolling stock travelling on them to wind loads. Windbreaks are a common solution for changing the flow characteristic in order to decrease unwanted effects induced by the presence of crosswind. The shelter effectiveness of a set of windbreaks placed over a railway twin-track embankment is experimentally analysed. A set of two-dimensional wind tunnel tests are undertaken and results corresponding to pressure tap measurements over a section of a typical high-speed train are herein presented.The results indicate that even small-height windbreaks provide sheltering effects to the vehicles. Also, eaves located at the windbreak tips seem to improve their sheltering effect.

Wind tunnel analysis of the flow topology over complex topographies

El principal objetivo de este trabajo es aportar conocimiento para contestar la pregunta: ¿hasta que punto los ensayos en túnel aerodinámico pueden contribuir a determinar las características que afectan la respuesta dinámica de los aerogeneradores operando en terreno complejo?. Esta pregunta no es nueva, de hecho, el debate en la comunidad científica comenzó en el primer tercio del siglo pasado y aún está intensamente vivo. El método generalmente aceptado para enfrentar el mencionado problema consiste en analizar un caso de estudio determinado en el cual se aplican tanto ensayos a escala real como análisis computacionales y ensayos en túnel aerodinámico. Esto no es ni fácil ni barato. Esta es la razón por la cual desde el experimento de Askervein en 1988, los modelizadores del flujo atmosférico tuvieron que esperar hasta 2007 a que el experimento de Bolund fuese puesto en marcha con un despliegue de medios técnicos equivalentes (teniendo en cuenta la evolución de las tecnologías de sensores y computación). El problema contempla tantos aspectos que ambas experiencias fueron restringidas a condiciones de atmósfera neutra con efectos de Coriolis despreciables con objeto de reducir la complejidad. Este es el contexto en el que se ha desarrollado la presente tesis doctoral. La topología del flujo sobre la isla de Bolund ha sido estudiada mediante la reproducción del experimento de Bolund en los túneles aerodinámicos A9 y ACLA16 del IDR. Dos modelos de la isla de Bolund fueron fabricados a dos escalas, 1:230 y 1:115. El flujo de entrada en el túnel aerodinámico simulando la capa límite sin perturbar correspondía a régimen de transición (transitionally rough regime) y fue usado como situación de referencia. El modelo a escala 1:230 fue ensayado en el túnel A9 para determinar la presión sobre su superficie. La distribución del coeficiente de presión sobre la isla proporcionó una visualización y estimación de una región de desprendimiento sobre el pequeño acantilado situado al frente de la misma. Las medidas de presión instantánea con suficiente grado de resolución temporal pusieron de manifiesto la no estacionariedad en la región de desprendimiento. El modelo a escala 1:115 fue ensayado utilizando hilo caliente de tres componentes y un sistema de velocimetría por imágenes de partículas de dos componentes. El flujo fue caracterizado por el ratio de aceleración, el incremento normalizado de energía cinética turbulenta y los ángulos de inclinación y desviación horizontal. Los resultados a lo largo de la dirección 270°y alturas de 2 m y 5 m presentaron una gran similitud con los resultados a escala real del experimento de Bolund. Los perfiles verticales en las localizaciones de las torres meteorológicas mostraron un acuerdo significativo con los resultados a escala real. El análisis de los esfuerzos de Reynolds y el análisis espectral en las localizaciones de los mástiles meteorológicos presentaron niveles de acuerdo variados en ciertas posiciones, mientras que en otras presentaron claras diferencias. El mapeo horizontal del flujo, para una dirección de viento de 270°, permitió caracterizar el comportamiento de la burbuja intermitente de recirculación sobre el pequeño acantilado existente al frente de la isla así como de la región de relajación y de la capa de cortadura en la región corriente abajo de Bolund. Se realizaron medidas de velocidad con alta resolución espacial en planos perpendiculares a la dirección del flujo sin perturbar. Estas medidas permitieron detectar y caracterizar una estructura de flujo similar a un torbellino longitudinal con regiones con altos gradientes de velocidad y alta intensidad de turbulencia. Esta estructura de flujo es, sin duda, un reto para los modelos computacionales y puede considerarse un factor de riesgo para la operación de los aerogeneradores. Se obtuvieron y analizaron distribuciones espaciales de los esfuerzos de Reynolds mediante 3CHW y PIV. Este tipo de parámetros no constituyen parte de los resultados habituales en los ensayos en túnel sobre topografías y son muy útiles para los modelizadores que utilizan simulación de grades torbellinos (LES). Se proporciona una interpretación de los resultados obtenidos en el túnel aerodinámico en términos de utilidad para los diseñadores de parques eólicos. La evolución y variación de los parámetros del flujo a lo largo de líneas, planos y superficies han permitido identificar como estas propiedades del flujo podrían afectar la localización de los aerogeneradores y a la clasificación de emplazamientos. Los resultados presentados sugieren, bajo ciertas condiciones, la robustez de los ensayos en túnel para estudiar la topología sobre terreno complejo y su comparabilidad con otras técnicas de simulación, especialmente considerando el nivel de acuerdo del conjunto de resultados presentados con los resultados a escala real. De forma adicional, algunos de los parámetros del flujo obtenidos de las medidas en túnel son difícilmente determinables en ensayos a escala real o por medios computacionales, considerado el estado del arte. Este trabajo fue realizado como parte de las actividades subvencionadas por la Comisión Europea como dentro del proyecto FP7-PEOPLE-ITN-2008WAUDIT (Wind Resource Assessment Audit and Standardization) dentro de la FP7 Marie-Curie Initial Training Network y por el Ministerio Español de Economía y Competitividad dentro del proyecto ENE2012-36473, TURCO (Determinación en túnel aerodinámico de la distribución espacial de parámetros estadísticos de la turbulencia atmosférica sobre topografías complejas) del Plan Nacional de Investigación (Subprograma de investigación fundamental no orientada 2012). El informe se ha organizado en siete capítulos y un conjunto de anexos. En el primer capítulo se introduce el problema. En el capítulo dos se describen los medios experimentales utilizados. Seguidamente, en el capítulo tres, se analizan en detalle las condiciones de referencia del principal túnel aerodinámico utilizado en esta investigación. En el capítulo tres se presentan resultados de ensayos de presión superficial sobre un modelo de la isla. Los principales resultados del experimento de Bolund se reproducen en el capítulo cinco. En el capítulo seis se identifican diferentes estructuras del flujo sobre la isla y, finalmente, en el capitulo siete, se recogen las conclusiones y una propuesta de lineas de trabajo futuras. ABSTRACT The main objective of this work is to contribute to answer the question: to which extend can the wind tunnel testing contribute to determine the flow characteristics that affect the dynamic response of wind turbines operating in highly complex terrains?. This question is not new, indeed, the debate in the scientific community was opened in the first third of the past century and it is still intensely alive. The accepted approach to face this problem consists in analysing a given case study where full-scale tests, computational modelling and wind tunnel testing are applied to the same topography. This is neither easy nor cheap. This is is the reason why since the Askervein experience in 1988, the atmospheric flow modellers community had to wait till 2007 when the Bolund experiment was setup with a deployment of technical means equivalent (considering the evolution of the sensor and computing techniques). The problem is so manifold that both experiences were restricted to neutral conditions without Coriolis effects in order to reduce the complexity. This is the framework in which this PhD has been carried out. The flow topology over the Bolund Island has been studied by replicating the Bolund experiment in the IDR A9 and ACLA16 wind tunnels. Two mock-ups of the Bolund island were manufactured at two scales of 1:230 and 1:115. The in-flow in the empty wind tunnel simulating the incoming atmospheric boundary layer was in the transitionally rough regime and used as a reference case. The 1:230 model was tested in the A9 wind tunnel to measure surface pressure. The mapping of the pressure coefficient across the island gave a visualisation and estimation of a detachment region on the top of the escarpment in front of the island. Time resolved instantaneous pressure measurements illustrated the non-steadiness in the detachment region. The 1:115 model was tested using 3C hot-wires(HW) and 2C Particle Image Velocimetry(PIV). Measurements at met masts M3, M6, M7 and M8 and along Line 270°were taken to replicate the result of the Bolund experiment. The flow was characterised by the speed-up ratio, normalised increment of the turbulent kinetic energy, inclination angle and turning angle. Results along line 270°at heights of 2 m and 5 m compared very well with the full-scale results of the Bolund experiment. Vertical profiles at the met masts showed a significant agreement with the full-scale results. The analysis of the Reynolds stresses and the spectral analysis at the met mast locations gave a varied level of agreement at some locations while clear mismatch at others. The horizontal mapping of the flow field, for a 270°wind direction, allowed to characterise the behaviour of the intermittent recirculation bubble on top of the front escarpment followed by a relaxation region and the presence of a shear layer in the lee side of the island. Further detailed velocity measurements were taken at cross-flow planes over the island to study the flow structures on the island. A longitudinal vortex-like structure with high mean velocity gradients and high turbulent kinetic energy was characterised on the escarpment and evolving downstream. This flow structure is a challenge to the numerical models while posing a threat to wind farm designers when siting wind turbines. Spatial distribution of Reynold stresses were presented from 3C HW and PIV measurements. These values are not common results from usual wind tunnel measurements and very useful for modellers using large eddy simulation (LES). An interpretation of the wind tunnel results in terms of usefulness to wind farm designers is given. Evolution and variation of the flow parameters along measurement lines, planes and surfaces indicated how the flow field could affect wind turbine siting. Different flow properties were presented so compare the level of agreement to full-scale results and how this affected when characterising the site wind classes. The results presented suggest, under certain conditions, the robustness of the wind tunnel testing for studying flow topology over complex terrain and its capability to compare to other modelling techniques especially from the level of agreement between the different data sets presented. Additionally, some flow parameters obtained from wind tunnel measurements would have been quite difficult to be measured at full-scale or by computational means considering the state of the art. This work was carried out as a part of the activities supported by the EC as part of the FP7- PEOPLE-ITN-2008 WAUDIT project (Wind Resource Assessment Audit and Standardization) within the FP7 Marie-Curie Initial Training Network and by the Spanish Ministerio de Economía y Competitividad, within the framework of the ENE2012-36473, TURCO project (Determination of the Spatial Distribution of Statistic Parameters of Flow Turbulence over Complex Topographies in Wind Tunnel) belonging to the Spanish National Program of Research (Subprograma de investigación fundamental no orientada 2012). The report is organised in seven chapters and a collection of annexes. In chapter one, the problem is introduced. In chapter two the experimental setup is described. Following, in chapter three, the inflow conditions of the main wind tunnel used in this piece of research are analysed in detail. In chapter three, preliminary pressure tests results on a model of the island are presented. The main results from the Bolund experiment are replicated in chapter five. In chapter six, an identification of specific flow strutures over the island is presented and, finally, in chapter seven, conclusions and lines for future works related to the presented one are included.

A dynamic factor model for mid-term forecasting of wind power generation

The main objective of this paper is the development and application of multivariate time series models for forecasting aggregated wind power production in a country or region. Nowadays, in Spain, Denmark or Germany there is an increasing penetration of this kind of renewable energy, somehow to reduce energy dependence on the exterior, but always linked with the increaseand uncertainty affecting the prices of fossil fuels. The disposal of accurate predictions of wind power generation is a crucial task both for the System Operator as well as for all the agents of the Market. However, the vast majority of works rarely onsider forecasting horizons longer than 48 hours, although they are of interest for the system planning and operation. In this paper we use Dynamic Factor Analysis, adapting and modifying it conveniently, to reach our aim: the computation of accurate forecasts for the aggregated wind power production in a country for a forecasting horizon as long as possible, particularly up to 60 days (2 months). We illustrate this methodology and the results obtained for real data in the leading country in wind power production: Denmark

Sistema eléctrico y de control de potencia de un túnel aerodinámico = Design of the power distribution and control system for a wind tunnel facility

El proyecto está basado en el estudio de la planta de potencia de un túnel aerodinámico. Para ello se ha realizado una breve introducción definiendo qué es un túnel aerodinámico, cuál es su propósito, qué tipos hay, etc. Posteriormente se ha escogido un tipo concreto de túnel entre todas las posibilidades y se ha procedido a su estudio. Se ha definido una forma y unas dimensiones y tras calcular las pérdidas de carga, se ha seleccionado la planta de potencia necesaria para compensar dichas pérdidas, dimensionándose también las conexiones de esta desde la acometida de potencia eléctrica. Por último se han dimensionado las conexiones correspondientes a la iluminación y los servicios que competen al túnel aerodinámico.

Nonlinear models for lateral dynamics of railway vehicles on bridges subject to wind action

The study of lateral dynamics of running trains on bridges is of importance mainly for the safety of the traffic, and may be relevant for laterally compliant bridges. These studies require threedimensional coupled vehicle-bridge models, wheree consideration of wheel to rail contact is a key aspect. Furthermore, an adequate evaluation of safety of rail traffic requires nonlinear models. A nonlinear coupled model is proposed here for vehicle-structure vertical and lateral dynamics. Vehicles are considered as fully three-dimensional multibody systems including gyroscopic terms and large rotation effects. The bridge structure is modeled by means of finite elements which may be of beam, shell or continuum type and may include geometric or material nonlinearities. The track geometry includes distributed track alignment irregularities. Both subsystems (bridge and vehicles) are described with coordinates in absolute reference frames, as opposed to alternative approaches which describe the multibody system with coordinates relative to the base bridge motion. The wheelrail contact employed is a semi-Hertzian model based on realistic wheel-rail profiles. It allows a detailed geometrical description of the contact patch under each wheel including multiple-point contact, flange contact and uplift. Normal and tangential stresses in each contact are integrated at each time-step to obtain the resultant contact forces. The models have been implemented within an existing finite element analysis software with multibody capabilities, Abaqus (Simulia Ltd., 2010). Further details of the model are presented in Antolín et al. (2012). Representative applications are presented for railway vehicles under lateral wind action on laterally compliant viaducts, showing the relevance of the nonlinear wheel-rail contact model as well as the interaction between bridge and vehicle.

Influencia del viento transversal en sistemas ferroviarios = Cross-wind effects on railway infrastructure

El viento, como factor medio-ambiental, ha sido objeto de numerosos estudios por los efectos que induce tanto en vehículos como en estructuras. Dentro del ámbito ferroviario, las cargas aerodinámicas debidas a la acción del viento transversal pueden poner en compromiso la seguridad de los vehículos en circulación, pudiendo llegar a ocasionar el vuelco del mismo. Incluso el sistema de cables encargado de realizar el suministro eléctrico necesario para la tracción del tren, conocido como catenaria, es sensible a la acción del viento. De hecho, al igual que ocurre en ciertas estructuras de cables, la interacción entre las fuerzas aerodinámicas no estacionarias y la catenaria puede ocasionar la aparición de oscilaciones de gran amplitud debido al fenómeno de galope. Una forma sencilla de reducir los efectos no deseados de la acción del viento, es la instalación de barreras cortavientos aguas arriba de la zona que se desea proteger. La instalación de estos dispositivos, reduce la velocidad en la estela generada, pero también modifica las propiedades del flujo dentro de la misma. Esta alteración de las condiciones del flujo puede contribuir a la aparición del fenómeno de galope en estructuras caracterizadas por su gran flexibilidad, como la catenaria ferroviaria. Estos dos efectos contrapuestos hacen evidente la importancia de mantener cierta visión global del efecto introducido por la instalación de barreras cortavientos en la plataforma ferroviaria. A lo largo de este documento, se evalúa desde un enfoque multidisciplinar el efecto inducido por las barreras cortavientos en varios subsistemas ferroviarios. Por un lado se analizan las mejoras en la estabilidad lateral del vehículo mediante una serie de ensayos en túnel de viento. La medición de la distribución de presiones en la superficie de un modelo bidimensional de vehículo ferroviario proporciona una buena estimación del nivel de protección que se consigue en función de la altura de una barrera cortavientos. Por otra parte, se analiza la influencia del mismo juego de barreras cortavientos en las características del flujo situado sobre la plataforma ferroviaria, mediante la utilización de anemometría de hilo caliente (HWA) y velocimetría de imágenes de párticulas (PIV). En particular se centra la atención en las características en la posición correspondiente a los hilos conductores de la catenaria. En la última parte del documento, se realiza un análisis simplificado de la aparición oscilaciones en la catenaria, por el efecto de la inestabilidad de galope. La información obtenida sobre las características del flujo se combinan con las propiedades aerodinámicas del hilo de contacto, obtenidas en mediante una serie de ensayos en túnel de viento. De esta manera se realiza una evaluación del riesgo a la aparición de este tipo de inestabilidad aeroeslástica aplicada a una catenaria ferroviaria situada sobre un viaducto tipo. ABSTRACT Wind as an environmental factor may induce undesirable effects on vehicles and structures. The analysis of those effects has caught the attention of several researchers. Concerning the railway system, cross-wind induces aerodynamic loads on rolling stock that may increase the overturning risk of the vehicle, threatening its safe operation. Even the cable system responsible to provide the electric current required for the train traction, known as the railway overhead or catenary, is sensitive to the wind action. In fact, the interaction between the unsteady aerodynamic forces and the railway overhead may trigger the development of undamped oscillations due to galloping phenomena. The inclusion of windbreaks upstream the area that needs wind protection is a simple mean to palliate the undesirable effects caused by the wind action. Although the presence of this wind protection devices reduces the wind speed downstream, they also modify the flow properties inside their wake. This modification on the flow characteristics may ease the apparition of the galloping phenomena on flexible structures, such as the railway overhead. This two opposite effects require to maintain a global perspective on the analysis of the influence of the windbreak presence. In the present document, a multidisciplinary analysis on the effect induced by windbreaks on several railways subsystems is conducted. On the one hand, a set of wind tunnel tests is conducted to assess the improvement on the rolling stock lateral stability. The qualitative estimation of the shelter effect, as function of the windbreak height, is established through the pressure distribution measured on the surface of a two-dimensional train model. On the other hand, the flow properties above the railway platform are assessed using the same set of windbreaks. Two experimental techniques are used to measure the flow properties, hot-wire anemometry (HWA) and particle image velocimetry (PIV). In particular, the attention is focused on the flow characteristics on the contact wire location. A simplified analysis on the catenary oscillations due to galloping phenomena is conducted in the last part of the document. Both, the flow characterization performed via PIV and the aerodynamic properties of the contact wire cross-section are combined. In this manner, the risk of the aeroelastic instabilities on a railway overhead placed on a railway bridge is assessed through a practical application.

Sistema eléctrico y de control de potencia de un tunel aerodinámico = Design of the power distributation and control system for a wind tunnel facility

La utilización de túneles aerodinámicos en ingeniería civil está cada vez más demandada debido al actual desarrollo urbanístico, esto es, la necesidad de edificios cada vez más altos en los que concentrar mayor cantidad de población, puentes y estructuras que faciliten el paso de medios de transporte alternativos, la importancia de los aspectos artísticos en la construcción (además de los funcionales), etc. Son muchos los factores que pueden hacer necesario el ensayo de alguna de esas estructuras en un túnel aerodinámico, y no existe un criterio universal a la hora de decidir si conviene o no hacerlo.

On the Analytical Approach to Present Engineering Problems: Photovoltaic Systems Behavior, Wind Speed Sensors Performance, and High-Speed Train Pressure Wave Effects in Tunnels

At present, engineering problems required quite a sophisticated calculation means. However, analytical models still can prove to be a useful tool for engineers and scientists when dealing with complex physical phenomena. The mathematical models developed to analyze three different engineering problems: photovoltaic devices analysis; cup anemometer performance; and high-speed train pressure wave effects in tunnels are described. In all cases, the results are quite accurate when compared to testing measurements.

A wind tunnel two-dimensional parametric investigation of biplane configurations

This paper presents an experimental and systematic investigation about how geometric parameters on a biplane configuration have an influence on aerodynamic parameters. This experimental investigation has been developed in a two-dimensional approach. Theoretical studies about biplanes configurations have been developed in the past, but there is not enough information about experimental wind tunnel data at low Reynolds number. This two-dimensional study is a first step to further tridimensional investigations about the box wing configuration. The main objective of the study is to find the relationships between the geometrical parameters which present the best aerodynamic behavior: the highest lift, the lowest drag and the lowest slope of the pitching moment. A tridimensional wing-box model will be designed following the pattern of the two dimensional study conclusions. It will respond to the geometrical relationships that have been considered to show the better aerodynamic behavior. This box-wing model will be studied in the aim of comparing the advantages and disadvantages between this biplane configuration and the plane configuration, looking for implementing the box-wing in the UAV?s field. Although the box wing configuration has been used in a small number of existing UAV, prestigious researchers have found it as a field of high aerodynamic and structural potential.

Offshore wind foundation design: some key issues

Despite the growth of the offshore wind industry, there are currently doubts relating to the design of wind facilities in the sea. This paper expounds current, already identified structural uncertainties: problems for soil characterization and transition piece (TP) design. This document also introduces new doubts or issues to be researched in the near future in this field (wave theory, scour process, wave load actions, scale difficulty, etc.), not as yet identified due to the scarce experience in the offshore wind industry. With this in mind, technical offshore wind standards related to foundation design have been reviewed.

The development of a wind tunnel DAQ system by using Labview tools

This paper presents the experimental three-year learning activity developed by a group of teachers in a wind tunnel facility. The authors, leading a team of students, carried out a project consisting of the design, assembly and testing of a wind tunnel. The project included all stages of the process from its initial specifications to its final quality flow assessments, going through the calculation of each element, and the building of the whole wind tunnel. The group of (final year) students was responsible for the whole wind tunnel project as a part of their bachelor degree project. The paper focuses on the development of wind tunnel data acquisition software. This automatic tool is essential to improve the automation of the data acquisition of the wind tunnel facility systems, in particular for a 6DOF multi-axis force/torque sensor. This work can be considered as a typical example of real engineering practice: a set of specifications that has to be modified due to the constraints imposed throughout the project, in order to obtain the final result

Aerodynamic loads on bluff bodies under wind gusts

Esta tesis doctoral se ha centrado en el estudio de las cargas aerodinámicas no estacionario en romos cuerpos o no aerodinámicos (bluff bodies). Con este objetivo se han identificado y analizado los siguientes puntos: -Caracterización del flujo medido con diferentes tipos de tubos de Pitot y anemómetro de hilo caliente en condiciones de flujo no estacionario inestable generado por un túnel aerodinamico de ráfagas. -Diseño e integración de los montajes experimentales requeridos para medir las cargas de viento internas y externas que actúan sobre los cuerpos romos en condiciones de flujo de viento con ráfagas. -Implementación de modelos matemáticos semi-empíricos basados en flujo potencial y las teorías fenomenológicas pertinentes para simular los resultados experimentales. -En diversan condiciones de flujo con ráfagas, la identificación y el análisis de la influencia de los parámetros obtenida a partir de los modelos teóricos desarrollados. -Se proponen estimaciones empíricas para averiguar los valores adecuados de los parámetros que influyente, mediante el ajuste de los resultados experimentales y los predichos teóricamente. Los montajes experimentales se has reakizado en un tunel aerodinamico de circuito abierto, provisto de baja velocidad, cámara de ensayes cerrada, un nuevo concepto de mecanismo generador de ráfaga sinusoidal, diseñado y construido en el Instituto de Microgravedad "Ignacio Da Riva" de la Universidad Politécnica de Madrid, (IDR / UPM). La principal característica de este túnel aerodynamico es la capacidad de generar un flujo con un perfil de velocidad uniforme y una fluctuación sinusoidal en el tiempo. Se han realizado pruebas experimentales para estudiar el efecto de los flujos no estacionarios en cuerpos romos situados en el suelo. Se han propuesto dos modelos teóricos para diterminar las cargas de presión externas e internas respectivamente. Con el fin de satisfacer la necesidad de la crea ráfagas de viento sinusoidales para comprobar las predicciones de los modelos teóricos, se han obtenido velocidades de hasta 30 m/s y frecuencias ráfaga de hasta 10 Hz. La sección de la cámara de ensayos es de 0,39 m x 0,54 m, dimensiónes adecuadas para llevar a cabo experimentos con modelos de ensayos. Se muestra que en la gama de parámetros explorados los resultados experimentales están en buen acuerdo con las predicciones de los modelos teóricos. Se han realizado pruebas experimentales para estudiar los efectos del flujo no estacionario, las cuales pueden ayudar a aclarar el fenómeno de las cargas de presión externa sobre los cuerpos romos sometidos a ráfagas de viento: y tambien para determinan las cargas de presión interna, que dependen del tamaño de los orificios de ventilación de la construcción. Por último, se ha analizado la contribución de los términos provenientes del flujo no estacionario, y se han caracterizado o los saltos de presión debido a la pérdida no estacionario de presión a través de los orificios de ventilación. ABSTRACT This Doctoral dissertation has been focused to study the unsteady aerodynamic loads on bluff bodies. To this aim the following points have been identified and analyzed: -Characterization of the flow measured with different types of Pitot tubes and hot wire anemometer at unsteady flow conditions generated by a gust wind tunnel. -Design and integrating of the experimental setups required to measure the internal and external wind loads acting on bluff bodies at gusty wind flow conditions. -Implementation of semi-empirical mathematical models based on potential flow and relevant phenomenological theories to simulate the experimental results.-At various gusty flow conditions, extracting and analyzing the influence of parameters obtained from the developed theoretical models. -Empirical estimations are proposed to find out suitable values of the influencing parameters, by fitting the experimental and theoretically predicted results. The experimental setups are performed in an open circuit, closed test section, low speed wind tunnel, with a new sinusoidal gust generator mechanism concept, designed and built at the Instituto de Microgravedad “Ignacio Da Riva” of the Universidad Politécnica de Madrid, (IDR/UPM). The main characteristic of this wind tunnel is the ability to generate a flow with a uniform velocity profile and a sinusoidal time fluctuation of the speed. Experimental tests have been devoted to study the effect of unsteady flows on bluff bodies lying on the ground. Two theoretical models have been proposed to measure the external and internal pressure loads respectively. In order to meet the need of creating sinusoidal wind gusts to check the theoretical model predictions, the gust wind tunnel maximum flow speed and, gust frequency in the test section have been limited to 30 m/s and 10 Hz, respectively have been obtained. The test section is 0.39 m × 0.54 m, which is suitable to perform experiments with testing models. It is shown that, in the range of parameters explored, the experimental results are in good agreement with the theoretical model predictions. Experimental tests have been performed to study the unsteady flow effects, which can help in clarifying the phenomenon of the external pressure loads on bluff bodies under gusty winds: and also to study internal pressure loads, which depend on the size of the venting holes of the building. Finally, the contribution of the unsteady flow terms in the theoretical model has been analyzed, and the pressure jumps due to the unsteady pressure losses through the venting holes have been characterized.

A study on the inclusion of forest canopy morphology data in numerical simulations for the purpose of wind resource assessment

A series of numerical simulations of the flow over a forest stand have been conducted using two different turbulence closure models along with various levels of canopy morphology data. Simulations have been validated against Stereoscopic Particle Image Velocimetry measurements from a wind tunnel study using one hundred architectural model trees, the porosities of which have been assessed using a photographic technique. It has been found that an accurate assessment of the porosity of the canopy, and specifically the variability with height, improves simulation quality regardless of the turbulence closure model used or the level of canopy geometry included. The observed flow field and recovery of the wake is in line with characteristic canopy flows published in the literature and it was found that the shear stress transport turbulence model was best able to capture this detail numerically.

Wind pumps for irrigating greenhouse crops: Comparison in different socio-economical frameworks

A methodology is applied for economic evaluation of water pumping technologies. Different socioeconomic frameworks are considered for Spain, Cuba and Pakistan. The levelised cost of energy is used to determine the best technology. Wind speed, distance to grid, water storage size and elevation are considered. The water elevation has greater influence on wind pumps than on solar PV pumping.