A novel preparation method of maleic anhydride grafted syndiotactic polystyrene and its blend performance with nylon6

This work is intended to provide a method for the preparation of maleic anhydride grafted syndiotactic polystyrene (sPS-g-MA). In particular, a novel solid reaction method by a radical grafting approach is investigated. The grafting reaction is performed at a solid state, where the syndiotactic polystyrene (sPS) is swollen in solvent at relatively low temperature compared to the conventional melt modification method. The formation of sPS-g-MA is directly confirmed by Fourier transform infrared spectroscopy and by the morphology observation of sPS/polyamide-6 (Nylon6) blends, when sPS-g-MA is used as a reactive compatibilizer.

Morphology and thermal and mechanical properties of PBT/HIPS and PBT/HIPS-g-GMA blends

The modification of high-impact polystyrene (HIPS) was accomplished by melt-grafting glycidyl methacrylate (GMA) on its molecular chains. Fourier transform infrared spectroscopy and electron spectroscopy for chemical analysis were used to characterize the formation of HIPS-g-GMA copolymers. The content of GMA in HIPS-g-GMA copolymer was determined by using the titration method. The effect of the concentrations of GMA and dicumyl peroxide on the degree of grafting was studied. A total of 1.9% of GMA can be grafted on HIPS. HIPS-g-GNU was used to prepare binary blends with poly(buthylene terephthalate) (PBT), and the evidence of reactions between the grafting copolymer and PBT in the blends was confirmed by scanning electron microscopy (SEM), dynamic mechanical analysis, and its mechanical properties. The SEM result showed that the domain size in PBT/HIPS-g-GMA blends was reduced significantly compared with that in PBT/HIPS blends; moreover, the improved strength was measured in PBT/HIPS-g-GMA blends and results from good interfacial adhesion. The reaction between ester groups of PBT and epoxy groups of HIPS-g-GMA can depress crystallinity and the crystal perfection of PBT.

Effect of the compatibilization of linear low-density polyethylene-g-acrylic acid on the morphology and mechanical properties of poly(butylene terephthalate)/linear low-density polyethylene blends

A poly(butylene terephthalate) (PBT)/linear low-density polyethylene (LLDPE) alloy was prepared with a reactive extrusion method, For improved compatibility of the blending system, LLDPE grafted with acrylic acid (LLDPE-g-AA) by radiation was adopted in place of plain LLDPE. The toughness and extensibility of the PBT/LLDPE-g-AA blends, as characterized by the impact strengths and elongations at break, were much improved in comparison with the toughness and extensibility of the PBT/LLDPE blends at the same compositions. However, there was not much difference in their tensile (or flexural) strengths and moduli. Scanning electron microscopy photographs showed that the domains of PBT/LLDPE-g-AA were much smaller and their dispersions were more homogeneous than the domains and dispersions of the PBT/ T,T PE blends. Compared with the related values of the PBT/LLDPE blends, the contents and melting temperatures of the usual spherulites of PBT in PBT/LLDPE-g-AA decreased.

聚β-羟基丁酸酯顺丁烯二酸酐接枝共聚物的等温结晶动力学和熔融行为

采用DSC方法对聚 β 羟基丁酸酯顺丁烯二酸酐接枝共聚物 (PHB g MA)的等温结晶动力学和熔融行为进行了研究 .结果表明 ,顺丁烯二酸酐的引入使得聚 β 羟基丁酸酯的结晶能力下降 ,但是并没有改变它的结晶成核机理和生长方式 .随着接枝率的增加 ,结晶活化能增加 .等温结晶后的PHB g MA表现出双熔融行为 ,这是在升温过程中发生熔融重结晶的结果

Preparation, characterization, and crystallization of naphthalene-labeled polypropylene

Naphthalene-labeled polypropylene (PP) was prepared by melt reaction of maleic anhydride-grafted-polypropylene (PP-g-MA) with 1-aminonaphthalene in a Barabender mixer chamber. The structure of the product was analyzed with fourier transform infrared (FT-IR), ultraviolet (UV) and fluorescence. The results showed that naphthyl groups grafted onto the PP molecular chains through the imide bonds formed between MA and 1-aminonaphthalene. The content of the chromophores was 1.8 X 10(-4) mol g(-1) measured by elemental analysis. Isothermal crystallization behavior was studied by differential scanning calorimeter (DSC). Labeled PP had a higher crystallization rate than PP-g-MA. Wide-angle X-Ray diffraction (WAXD) analysis revealed that labeled PP had higher crystallinity than PP-g-MA.

Isothermal crystallization kinetics of PEO in poly(ethylene terephthalate)-poly(ethylene oxide) segmented copolymers. I. Effect of the sofi-block length

The isothermal crystallization kinetics of poly(ethylene oxide) (PEO) block in two poly(ethylene terephthalate) (PET)-PEO segmented copolymers was studied with differential scanning calorimetry. The Avrami equation failed to describe the overall crystallization process, but a modified Avrami equation, the Q equation, did. The crystallizability of the PET block and the different lengths of the PEO block exerted strong influences on the crystallization process, the crystallinity, and time final morphology of the PEO block. The mechanism of nucleation and the growth dimension of the PEG block were different because of the crystallizability of time PET block and the compositional heterogeneity. The crystallization of the PEO block was physically constrained by the microstructure of time PET crystalline phase, which resulted in a lower crystallization rate. However, this influence became weak with the increase in the soft-block length. (C) 2000 John Wiley & Sons, Inc.

Toughening PA1010 with a functionalized saturated polyolefin elastomer

Polyamide (PA)1010 is blended with a saturated polyolefin elastomer, ethylene-cu-olefin copolymer (EOCP). To improve the compatibility of PA1010 with EOCP, different grafting rates of EOCP with maleic anhydride (MA) are used. The reaction between PA1010 and EOCP-g-MA during extrusion is verified through an extraction test. Mechanical properties, such as notched Izod impact strength, elongation at break, etc., are examined as a function of grafting rate and weight fraction of elastomer. It was found that in the scale of grafting rate (0.13-0.92 wt %), 0.51 wt % is an extreme point for several mechanical properties. Elastomer domains of PA1010/ EOCP-g-MA blends show a finer and more uniform dispersion in the matrix than that of PA1010/EOCP blends. For the same grafting rate, the average sizes of elastomer particles are almost independent on the contents of elastomer, but for different grafting rates, the particle sizes are decreased with increasing grafting rate. The copolymer formed during extrusion strengthens the interfacial adhesion and acts as an emulsifier to prevent the aggregation of elastomer in the process of blending. (C) 2000 John Wiley & Sons, Inc.

Effect of compatibilization on the properties of HIPS/PA1010 blends

Blends consisting of high-impact polystyrene (HIPS) as the matrix and polyamide 1010 (PA1010) as the dispersed phase were prepared by mixing. The grafting copolymers of HIPS and maleic anhydride (MA), the compatibilizer precursors of the blends, were synthesized. The contents of the IMA in the grafting copolymers are 4.7 wt % and 1.6 wt %, and were assigned as HAM and LMA, respectively. Different blend morphologies were observed by scanning electron microscopy (SEM); the domain size of the PA1010 dispersed phase in the HIPS matrix of compatibilized blends decreased comparing with that of uncompatibilized blends. For the blend with 25 wt % HIPS-g-MA component, the T-c of PA1010 shifts towards lower temperature, from 178 to 83 degrees C. It is found that HIPS-g-MA used as the third component has profound effect on the mechanical properties of the resulting blends. This behavior has been attributed to the chemical reaction taking place in situ during the mixing between the two components of PA1010 and HIPS-g-MA. (C) 2000 John Wiley & Sons, Inc.

Chlorohydrin water swellable rubber compatibilized by an amphiphilic craft copolymer. I. Synthesis and characterization of compatibilizer PVA-g-PBA

The graft copolymerization of butyl acrylate onto poly(vinyl alcohol) with eerie ammonium nitrate as redox initiator in a aqueous medium has been investigated. The formation of graft copolymer was confirmed by means of IR, scanning electron microscopy (SEM), and wide-angle X-ray diffraction (WAXD). The percentage of mononer conversion and percentage of grafting varied with concentrations of initiator, nitric acid, monomer, macromolecular backbone (X-n = 1750, M = 80 000), reaction temperature and reaction time. Some inorganic salts and organic solvents have a great influence upon grafting. The reaction mechanism has been explored, and rate equations for the reaction are established. (C) 2000 John Wiley & Sons, Inc.

Morphology, thermal behavior, and mechanical properties of PA6/UHMWPE blends with HDPE-g-MAH as a compatibilizing agent

A functionalized high-density polyethylene (HDPE) with maleic anhydride (MAH) was prepared using a reactive extruding method. This copolymer was used as a compatibilizer of blends of polyamide 6 (PA6) and ultrahigh molecular weight polyethylene (UHMWPE). Morphologies were examined by a scanning electron microscope. It was found that the dimension of UHMWPE and HDPE domains in the PA6 matrix decreased dramatically, compared with that of the uncompatibilized blending system. The size of the UHMWPE domains was reduced from 35 mu m (PA6/UHMWPE, 80/20) to less than 4 mu m (PA6/UHMWPE/HDPE-g-MAH, 80/20/20). The tensile strength and Izod impact strength of PA6/UHMWPE/HDPE-g-MAH (80/20/20) were 1.5 and 1.6 times as high as those of PA6/UHMWPE: (80/20), respectively. This behavior could be attributed to chemical reactions between the anhydride groups of HDPE-g-MAH and the terminal amino groups of PA6 in PA6/UHMWPE/HDPE-g-MAH blends. Thermal analysis was performed to confirm that the above chemical reactions took place during the blending process. (C) 2000 John Wiley & Sons, Inc.

LLDPE-g-AA的流变行为及力学性能

利用毛细管流变仪研究了线性低密度聚乙烯接枝丙烯酸 (LLDPE - g -AA)的流变行为。结果表明 ,在高的剪切应力下LLDPE -g -AA的表观粘度比纯LLDPE的小 ,并改进了树脂的流动性和加工性。LLDPE - g -AA的表观粘度随接枝丙烯酸含量的增加而降低 ,说明接枝到LLDPE分子链上的丙烯酸起到了内润滑剂的作用。利用Instron 112 1拉力机测试了LLDPE - g -AA的力学性能 ,结果表明其拉伸强度、杨氏模量和断裂伸长率与纯LLDPE相比没有明显的变化

实时BIA技术对蛋白A与免疫球蛋白G相互作用的研究

应用实时BIA技术 ,探讨了蛋白A与小鼠免疫球蛋白G (MIgG)之间的相互作用 ,求出相互作用的动力学速率常数ka=5 0 7× 1 0 4 (mol/L) - 1 s- 1 ,kd=9 65× 1 0 - 5(s- 1 ) ,结合常数KA=5 2 5× 1 0 8(mol/L) - 1 .同时使用蛋白A固定的传感片用于MIgG浓度的检测 ,在 0 64～ 1 2mg/L浓度区间内 ,MIgG的响应值与其浓度有非常好的线性关系.

The compatibility and morphology of HIPS/PC and HIPS-g-GMA/PC blends

The compatibility and morphology of HIPS/PC and HIPS-g-GMA/PC blends were studied. The compatibility and morphology of HIPS/PC blends were characterized by DSC and SEM, respectively. The result of DSC shows that T-g of PS doesn't change with the blend composition, and T-g of PC decreases with the increase in weight fraction of HIPS, which indicates that the PC/HIPS blend is a partially miscible system. Results of SEM indicate that the decrease in T-g of PC results from PS interpenetrating into the phase of PC, and no change in T-g of PS results from PC not interpenetrating into the phase of PS. The copolymer of HIPS-g-GMA was prepared by reactive grafting method. The IR spectrum shows that GMA is grafted on the chain of HIPS. The compatibility and morphology of HIPS-gGMA (35)/PC (65) were studied by DSC and SEM. PC (65)/HEPS-g-GMA (35) blend exhibits reduced size of disperse phase, enhanced interface adhesion and lower T-g of PC phase as compared with the PC(65)/HIPS(35) blend. It implies that HIPS-g-GMA is an effective compatibilizer of the HIPS/PC blend.

Nonisothermal crystallization kinetics: poly(ethylene terephthalate)-poly(ethylene oxide) segmented copolymer and poly(ethylene oxide) homopolymer

The nonisothermal crystallization behavior of polyethylene oxide (PEO) in poly(ethylene terephthalate)poly(ethylene oxide) (PETPEO) segmented copolymer and PEO homopolymer has been studied by means of differential scanning calorimetry, as well as transmission electron microscope. The kinetics of PEO in copolymer and PEO homopolymer under nonisothermal crystallization condition has been analyzed by Ozawa equation. The results show that Ozawa equation only describes the crystallization behavior of PEO-6000 homopolymer successfully, but fails to describe the whole crystallization process of PEO in copolymer because the secondary crystallization in the later stage could not be neglected. Due to the constraint of PET segments imposed on the PEO segments, a distinct two stage of crystallization of PEO in copolymer has been investigated by using Avrami equation modified by Jeziorny to deal with the nonisothermal crystallization data. In the case of PEO-6000 homopolymer, good linear relation for the whole crystallization process is obtained owing to the secondary crystallization does not occur under our experimental condition. (C) 2001 Elsevier Science Ltd. All rights reserved.

聚β-羟基丁酸酯顺丁烯二酸酐接枝共聚物的研究

采用DSC、TGA、POM和WAXD等方法对聚 β 羟基丁酸酯 (PHB)及其接枝顺丁烯二酸酐共聚物 (PHB g MA)的结晶行为、热稳定性和生物降解特性进行了研究 .结果表明接枝产物的热稳定性明显优于PHB ,热分解温度提高了 2 0余度 ;结晶行为发生很大的变化 .结晶速率减小 ,结晶温度降低 ,冷结晶温度升高 ,球晶的织态结构也随着MA接枝量的变化发生明显变化 ,并且接枝MA促进了PHB的生物降解