Evaluation of Asphalt Mixes Made from Reclaimed Concrete Aggregates, MLR-85-07, 1986

Three comparable hot mixed asphalt paving mixes were produced using two different aggregates produced from reclaimed portland cement concrete paving and one from a crushed limestone aggregate. These were subjected both dry and soaked to indirect tensile tests to determine the wet strength retention. One mix made from reclaimed concrete demonstrated a slightly better strength retention than the limestone mix and the other less. Satisfactory asphalt paving mixes can be produced from reclaimed concrete pavements but the increased asphalt demand (about 1%) negates part of the potential savings.

Investigation of Steel-Stringer Bridges: Superstructures and Substructures, Volume I, TR-522, 2007

There are hundreds of structurally deficient or functionally obsolete bridges in the state of Iowa. With the majority of these bridges located on rural county roads where there is limited funding available to replace the bridges, diagnostic load testing can be utilized to determine the actual load carrying capacity of the bridge. One particular family or fleet of bridges that has been determined to be desirable for load testing consists of single-span bridges with non-composite, cast-in-place concrete decks, steel stringers, and timber substructures. Six bridges with poor performing superstructure and substructure from the aforementioned family of bridges were selected to be load tested. The six bridges were located on rural roads in five different counties in Iowa: Boone, Carroll, Humboldt, Mahaska, and Marshall. Volume I of this report focuses on evaluating the superstructure for this family of bridges. This volume discusses the behavior characteristics that influence the load carrying capacity of this fleet of bridges. In particular, the live load distribution, partial composite action, and bearing restraint were investigated as potential factors that could influence the bridge ratings. Implementing fleet management practices, the bridges were analyzed to determine if the load test results could be predicted to better analyze previously untested bridges. For this family of bridges it was found that the ratings increased as a result of the load testing demonstrating a greater capacity than determined analytically. Volume II of this report focuses on evaluating the timber substructure for this family of bridges. In this volume, procedures for detecting pile internal decay using nondestructive ultrasonic stress wave techniques, correlating nondestructive ultrasonic stress wave techniques to axial compression tests to estimate deteriorated pile residual strength, and evaluating load distribution through poor performing timber substructure elements by instrumenting and load testing the abutments of the six selected bridges are discussed. Also, in this volume pile repair methods for restoring axial and bending capacities of pile are developed and evaluated.

Investigation of Steel-Stringer Bridges: Superstructures and Substructures, Volume II, TR-522, 2007

Problems with unknown bridge foundations in Iowa are often associated with timber substructures. Timber piles are subject to biological and physical deterioration, which makes quantifying in-service pile capacity difficult. Currently there are no reliable means to estimate the residual carrying capacity of an in-service deteriorated pile; and thus, the overall safety of the bridge cannot be determined. The lack of reliable evaluation methods can lead to conservative and costly maintenance practices. This research study was undertaken to investigate procedures for assessing bridge substructures, and evaluating procedures for rehabilitating/strengthening/replacing inadequate substructure components. The report includes an extensive literature review, a field reconnaissance study of 49 bridges, a survey of substructure problems from the perspective of County Engineers, a laboratory study aiming to correlate nondestructive tests to residual pile strength and stiffness values, nondestructive and destructive load tests for 6 bridges with poor substructures, and finally a laboratory study evaluating selected repair methods.

The Network Company in Catalonia : ICT, Productivity, Competitiveness, Salaries and Performance in Catalonia's Companies. Research report (synthesis document)

Resum en anglès del projecte de recerca L'empresa xarxa a Catalunya. TIC, productivitat, competitivitat, salaris i beneficis a l'empresa catalana té com a objectiu principal constatar que la consolidació d'un nou model estratègic, organitzatiu i d'activitat empresarial, vinculat amb la inversió i l'ús de les TIC (o empresa xarxa), modifica substancialment els patrons de comportament dels resultats empresarials, en especial la productivitat, la competitivitat, les retribucions dels treballadors i el benefici. La contrastació empírica de les hipòtesis de treball l'hem feta per mitjà de les dades d'una enquesta a una mostra representativa de 2.038 empreses catalanes. Amb la perspectiva de l'impacte de la inversió i l'ús de les TIC no s'aprecia una relació directa entre els processos d'innovació digital i els resultats de l'activitat de l'empresa catalana. En aquest sentit, hem hagut de segmentar el teixit productiu català per a buscar les organitzacions en què el procés de coinnovació tecnològica digital i organitzativa és més present i en què la intensitat de l'ús del coneixement és un recurs molt freqüent per a poder copsar impactes rellevants en els principals resultats empresarials. Això és així perquè l'economia catalana, avui, presenta una estructura productiva dual.

L'empresa xarxa a Catalunya : TIC, productivitat, competitivitat, salaris i rendiment a les empreses de Catalunya. Informe final de recerca (volum II)

El projecte de recerca L'empresa xarxa a Catalunya. TIC, productivitat, competitivitat, salaris i beneficis a l'empresa catalana té com a objectiu principal constatar que la consolidació d'un nou model estratègic, organitzatiu i d'activitat empresarial, vinculat amb la inversió i l'ús de les TIC (o empresa xarxa), modifica substancialment els patrons de comportament dels resultats empresarials, en especial la productivitat, la competitivitat, les retribucions dels treballadors i el benefici. La contrastació empírica de les hipòtesis de treball l'hem feta per mitjà de les dades d'una enquesta a una mostra representativa de 2.038 empreses catalanes. Amb la perspectiva de l'impacte de la inversió i l'ús de les TIC no s'aprecia una relació directa entre els processos d'innovació digital i els resultats de l'activitat de l'empresa catalana. En aquest sentit, hem hagut de segmentar el teixit productiu català per a buscar les organitzacions en què el procés de coinnovació tecnològica digital i organitzativa és més present i en què la intensitat de l'ús del coneixement és un recurs molt freqüent per a poder copsar impactes rellevants en els principals resultats empresarials. Això és així perquè l'economia catalana, avui, presenta una estructura productiva dual.

L'empresa xarxa a Catalunya : TIC, productivitat, competitivitat, salaris i rendiment a les empreses de Catalunya. Informe final de recerca (volum I)

El projecte de recerca L'empresa xarxa a Catalunya. TIC, productivitat, competitivitat, salaris i beneficis a l'empresa catalana té com a objectiu principal constatar que la consolidació d'un nou model estratègic, organitzatiu i d'activitat empresarial, vinculat amb la inversió i l'ús de les TIC (o empresa xarxa), modifica substancialment els patrons de comportament dels resultats empresarials, en especial la productivitat, la competitivitat, les retribucions dels treballadors i el benefici. La contrastació empírica de les hipòtesis de treball l'hem feta per mitjà de les dades d'una enquesta a una mostra representativa de 2.038 empreses catalanes. Amb la perspectiva de l'impacte de la inversió i l'ús de les TIC no s'aprecia una relació directa entre els processos d'innovació digital i els resultats de l'activitat de l'empresa catalana. En aquest sentit, hem hagut de segmentar el teixit productiu català per a buscar les organitzacions en què el procés de coinnovació tecnològica digital i organitzativa és més present i en què la intensitat de l'ús del coneixement és un recurs molt freqüent per a poder copsar impactes rellevants en els principals resultats empresarials. Això és així perquè l'economia catalana, avui, presenta una estructura productiva dual.

An international university network for online teaching of pathology in Frenchspeaking countries

Introduction: Building online courses is a highly time consuming task for teachers of a single university. Universities working alone create high-quality courses but often cannot cover all pathological fields. Moreover this often leads to duplication of contents among universities, representing a big waste of teacher time and energy. We initiated in 2011 a French university network for building mutualized online teaching pathology cases, and this network has been extended in 2012 to Quebec and Switzerland. Method: Twenty French universities (see & for details), University Laval in Quebec and University of Lausanne in Switzerland are associated to this project. One e-learning Moodle platform (http://moodle.sorbonne-paris-cite.fr/) contains texts with URL pointing toward virtual slides that are decentralized in several universities. Each university has the responsibility of its own slide scanning, slide storage and online display with virtual slide viewers. The Moodle website is hosted by PRES Sorbonne Paris Cité, and financial supports for hardware have been obtained from UNF3S (http://www.unf3s.org/) and from PRES Sorbonne Paris Cité. Financial support for international fellowships has been obtained from CFQCU (http://www.cfqcu.org/). Results: The Moodle interface has been explained to pathology teachers using web-based conferences with screen sharing. The teachers added then contents such as clinical cases, selfevaluations and other media organized in several sections by student levels and pathological fields. Contents can be used as online learning or online preparation of subsequent courses in classrooms. In autumn 2013, one resident from Quebec spent 6 weeks in France and Switzerland and created original contents in inflammatory skin pathology. These contents are currently being validated by senior teachers and will be opened to pathology residents in spring 2014. All contents of the website can be accessed for free. Most contents just require anonymous connection but some specific fields, especially those containing pictures obtained from patients who agreed for a teaching use only, require personal identification of the students. Also, students have to register to access Moodle tests. All contents are written in French but one case has been translated into English to illustrate this communication (http://moodle.sorbonne-pariscite.fr/mod/page/view.php?id=261) (use "login as a guest"). The Moodle test module allows many types of shared questions, making it easy to create personalized tests. Contents that are opened to students have been validated by an editorial committee composed of colleagues from the participating institutions. Conclusions: Future developments include other international fellowships, the next one being scheduled for one French resident from May to October 2014 in Quebec, with a study program centered on lung and breast pathology. It must be kept in mind that these e-learning programs highly depend on teachers' time, not only at these early steps but also later to update the contents. We believe that funding resident fellowships for developing online pathological teaching contents is a win-win situation, highly beneficial for the resident who will improve his knowledge and way of thinking, highly beneficial for the teachers who will less worry about access rights or image formats, and finally highly beneficial for the students who will get courses fully adapted to their practice.

Communicating Highway Safety: What Works, 2002

Few topics in transportation are of greater significance, now and in the future, than making today’s roads safe for those who use them. This study aims to assist the formulation of policy by examining the empirical evidence currently available on the ability of several forms of communication efforts and activities to increase knowledge about and affect attitudes and behavior toward highway safety practices. The objective of this effort is to provide a comparative synthesis of what works and what does not in highway safety campaigns across a large number of topical areas that have a mass media component. This was accomplished by conducting an extensive literature review to determine the current state of knowledge concerning what works and what has significant potential for wide use in future highway safety campaigns. An analytic framework for investigating highway safety campaigns was created. The framework includes (1) the types of media components, (2) the types of collaborations, (3) the context in which the campaign is intended to have impact, (4) the structure or procedural steps into which campaigns are organized, (5) the principles for what works in a campaign, and (6) the desired impact of a campaign on its target audience. The report reveals 25 characteristics of successful communication campaigns, strategies that stand a chance of achieving changes in knowledge, attitude, and behavior. The actual impact of mass communication remains unproven because of a perceived lag in the development of adequate evaluation techniques. Education by itself has not generally resulted in significant changes in the behaviors targeted, but education of the public and advocacy groups has often helped enact necessary legislation, transmit knowledge about the provisions and penalties of laws in ways that increase their deterrent effect, and generate public support for law enforcement programs. Even in such cases, however, when enforcement is inconsistent, public compliance frequently decreases with time. Approaches to traffic safety that emphasize the need for long-term individual- and community-based measures are found to be especially crucial for addressing complex problems like drinking and driving that are determined by a myriad of lifestyle and psychosocial factors.

Testing differentiation in diploid populations.

We examine the power of different exact tests of differentiation for diploid populations. Since there is not necessarily random mating within populations, the appropriate hypothesis to construct exact tests is that of independent sampling of genotypes. There are two categories of tests, FST-estimator tests and goodness of fit tests. In this latter category, we distinguish "allelic statistics", which account for the nature of alleles within genotypes, from "genotypic statistics" that do not. We show that the power of FST-estimator tests and of allelic goodness of fit tests are similar when sampling is balanced, and higher than the power of genotypic goodness of fit tests. When sampling is unbalanced, the most powerful tests are shown to belong to the allelic goodness of fit group.

NDA waveform estimation in the low-SNR regime

This correspondence addresses the problem of nondata-aidedwaveform estimation for digital communications. Based on the unconditionalmaximum likelihood criterion, the main contribution of this correspondenceis the derivation of a closed-form solution to the waveform estimationproblem in the low signal-to-noise ratio regime. The proposed estimationmethod is based on the second-order statistics of the received signaland a clear link is established between maximum likelihood estimation andcorrelation matching techniques. Compression with the signal-subspace isalso proposed to improve the robustness against the noise and to mitigatethe impact of abnormals or outliers.

Metsäteollisuuden prosessien suunnittelu simulointiympäristössä

Prosessisimulointiohjelmistojen käyttö on yleistynyt paperiteollisuuden prosessien kartoituksessa ja kyseiset ohjelmistot ovat jo pitkään olleet myös Pöyry Engineering Oy:n työkaluja prosessisuunnittelussa. Tämän työn tavoitteeksi määritettiin prosessisimulointiohjelmistojen käytön selvittäminen suomalaisissa paperitehtaissa sekä prosessisimuloinnin tulevaisuuden näkymien arviointi metsäteollisuuden suunnittelupalveluissa liiketoiminnan kehittämiseksi. Työn teoriaosassa selvitetään mm. seuraavia asioita: mitä prosessisimulointi on, miksi simuloidaan ja mitkä ovat simuloinnin hyödyt ja haasteet. Teoriaosassa esitellään yleisimmät käytössä olevat prosessisimulointiohjelmistot, simulointiprosessin eteneminen sekä prosessisimuloinnin tuotteistamisen vaatimuksia. Työn kokeellisessa osassa selvitettiin kyselyn avulla prosessisimulointiohjelmistojen käyttöä Suomen paperitehtaissa. Kysely lähetettiin kaikille Suomen tärkeimmille paperitehtaille. Kyselyn avulla selvitettiin mm, mitä ohjelmia käytetään, mitä on simuloitu, mitä pitää vielä simuloida ja kuinka tarpeellisena prosessisimulointia pidetään. Työntulokset osoittavat, että kaikilla kyselyyn vastanneilla suomalaisilla paperitehtailla on käytetty prosessisimulointia. Suurin osa simuloinneista on tehty konelinjoihin sekä massa- ja vesijärjestelmiin. Tulevaisuuden tärkeimpänä kohteena pidetään energiavirtojen simulointia. Simulointimallien pitkäjänteisessä hyödyntämisessä ja ylläpidossa on kehitettävää, jossa simulointipalvelujen hankkiminen palveluna on tehtaille todennäköisin vaihtoehto. Johtopäätöksenä on se, että tehtailla on tarvetta prosessisimuloinnille. Ilmapiiri on kyselytuloksien mukaan suotuisa ja simulointi nähdään tarpeellisena työkaluna. Prosessisimuloinnin markkinointia, erillispalvelutuotteen lisäksi, kannattaisi kehittää siten, että simulointimallin ylläpito jatkuisi projektin jälkeen lähipalveluna. Markkinointi pitäisi tehdä jo projektin alkuvaiheessa tai projektin aikana. Simulointiohjelmien kirjosta suunnittelutoimiston kannattaa valita simulointiohjelmistoja, jotka sopivat sille parhaiten. Erityistapauksissa muiden ohjelmien hankintaa kannattaa harkita asiakkaan toivomusten mukaisesti.

Official Positions for FRAX® clinical regarding prior fractures from Joint Official Positions Development Conference of the International Society for Clinical Densitometry and International Osteoporosis Foundation on FRAX®.

The 2010 Position Development Conference addressed four questions related to the impact of previous fractures on 10-year fracture risk as calculated by FRAX(®). To address these questions, PubMed was searched on the keywords "fracture, epidemiology, osteoporosis." Titles of retrieved articles were reviewed for an indication that risk for future fracture was discussed. Abstracts of these articles were reviewed for an indication that one or more of the questions listed above was discussed. For those that did, the articles were reviewed in greater detail to extract the findings and to find additional past work and citing works that also bore on the questions. The official positions and the supporting literature review are presented here. FRAX(®) underestimates fracture probability in persons with a history of multiple fractures (good, A, W). FRAX(®) may underestimate fracture probability in individuals with prevalent severe vertebral fractures (good, A, W). While there is evidence that hip, vertebral, and humeral fractures appear to confer greater risk of subsequent fracture than fractures at other sites, quantification of this incremental risk in FRAX(®) is not possible (fair, B, W). FRAX(®) may underestimate fracture probability in individuals with a parental history of non-hip fragility fracture (fair, B, W). Limitations of the methodology include performance by a single reviewer, preliminary review of the literature being confined to titles, and secondary review being limited to abstracts. Limitations of the evidence base include publication bias, overrepresentation of persons of European descent in the published studies, and technical differences in the methods used to identify prevalent and incident fractures. Emerging topics for future research include fracture epidemiology in non-European populations and men, the impact of fractures in family members other than parents, and the genetic contribution to fracture risk.

Adaptando Metalib al usuario : la experiencia de la UOC

The implementation of Metalib in UOC's Library was framed within a project centred on the end user. For the adaptation of Metalib to the users' needs and search behaviour, we carried out three tests: - One with students, conducted by a consulting company; - A second one with teachers, carried out by the Library; - The third, with teachers and staff, also was carried out by the Library, after having made some changes resulting from the first and second tests. The tests, made with the software Morae, underlined a number of difficulties to understand the concepts related to metasearching. The tests also showed difficulties in navigating and in managing search results. All the information gathered was used to improve navigation through the interface. The presentation tells about the tests' methodology, the conclusions reached through this experience, and the decisions finally taken by the Library to improve the Metalib interface.

Natural or naturalized? phylogeography suggests that the abundant sea urchin arbacia lixula Is a recent Colonizer of the Mediterranean

We present the global phylogeography of the black sea urchin Arbacia lixula, an amphi-Atlantic echinoid with potential to strongly impact shallow rocky ecosystems. Sequences of the mitochondrial cytochrome c oxidase gene of 604 specimens from 24 localities were obtained, covering most of the distribution area of the species, including the Mediterranean and both shores of the Atlantic. Genetic diversity measures, phylogeographic patterns, demographic parameters and population differentiation were analysed. We found high haplotype diversity but relatively low nucleotide diversity, with 176 haplotypes grouped within three haplogroups: one is shared between Eastern Atlantic (including Mediterranean) and Brazilian populations, the second is found in Eastern Atlantic and the Mediterranean and the third is exclusively from Brazil. Significant genetic differentiation was found between Brazilian, Eastern Atlantic and Mediterranean regions, but no differentiation was found among Mediterranean sub-basins or among Eastern Atlantic sub-regions. The star-shaped topology of the haplotype network and the unimodal mismatch distributions of Mediterranean and Eastern Atlantic samples suggest that these populations have suffered very recent demographic expansions. These expansions could be dated 94-205 kya in the Mediterranean, and 31-67 kya in the Eastern Atlantic. In contrast, Brazilian populations did not show any signature of population expansion. Our results indicate that all populations of A. lixula constitute a single species. The Brazilian populations probably diverged from an Eastern Atlantic stock. The present-day genetic structure of the species in Eastern Atlantic and the Mediterranean is shaped by very recent demographic processes. Our results support the view (backed by the lack of fossil record) that A. lixula is a recent thermophilous colonizer which spread throughout the Mediterranean during a warm period of the Pleistocene, probably during the last interglacial. Implications for the possible future impact of A. lixula on shallow Mediterranean ecosystems in the context of global warming trends must be considered.

The Development of an Internal Testing Process for a Bluetooth Product

BlueGiga Technologies on uusi Bluetooth -teknologiaa soveltava pk-yritys. Yrityksen tuotekehitysprosessia täydentämään tarvittiin testausprosessi. Testausprosessin luominen oli haastavaa, koska Bluetooth -teknologia on uutta ja yritys on vielä nuori. Lisäksi se integroi kovo- ja ohjelmistokomponentteja tuotteissaan. Testaus aloitettiin evaluoimalla standardinmukaista tapaa dokumentoida testit. Tämän jälkeen tutkittiin BlueGigan ohjelmistokehitysprosessin suhdetta olemassa oleviin ohjelmistokehitysprosesseihin. Samanaikaisesti perehdyttiin Bluetooth -kvalifikaation testaukselle asettamiin vaatimuksiin. Tämän seurauksena TTCN:ää kokeiltiin helppolukuisen testitapauksen määrittelyssä. Käyttötapauksiin perustuvan testauksen sopivuutta Wireless Remote Access Platform:in (WRAP) testaamiseen arvioitiin kokeilemalla sitä Man-to-Machine -käyttötapauksen testaamisessa. Yllämainittujen tehtävien aikana kerätyn tiedon ja hankittujen kokemusten pohjalta laadittiin testausprosessi, joka kattaa yksikkö-, integraatio- ja järjestelmätason testauksen. Painopiste on järjestelmätason testauksessa. Prosessi määrittelee myös vastuuhenkilön tai -henkilöt eri testaustasoille.