Tamanho de gotas de pontas de pulverização em diferentes condições operacionais por meio da técnica de difração do raio laser

The present study aimed to evaluate the droplet spectrum of hydraulic nozzles, under different pressures and spray liquid compositions, using a laser particle size analyzer. In a completely randomized design, two air induction twin flat-fan nozzles (AD-IA/D 11002 and AD-IA/D11004) and two hollow-cone nozzles (MAG - 2 and MAG - 4) were evaluated, in factorial design 3 x 2: tree spray pressures (207, 276 and 345 kPa for twin flat-fan nozzles, and 414, 483 and 552 kPa for cone nozzles); and two spray liquid compositions (water and water plus phosphatydilcoline + propionic acid adjuvant). The addition of adjuvant reduced the volume median diameter for the AD-IA/D 11002 and 11004 nozzles; however it had an opposite effect with the MAG - 4 nozzles and not changed with the MAG - 2 nozzles. In adverse weather conditions, it is not recommended the use of hollow cone spray nozzle, even with the addition of adjuvant tested because of the high risk potential of drift.

The importance of Leptospira interrogans serovars Icterohaemorrhagiae and Canicola in coastal zone and in southern fields of Rio Grande do Sul, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo clínico comparativo entre sutura convencional e vaporização a laser de dióxido de carbono (CO2) em pele de ratos

The proposal of this study was to compare a wound healing between conventional suture and vaporization with CO2 laser in rats skin. ln such case 24 rats were utilized, making two longitudinal incisions in dorsum by scalpel. ln the left side incision the wound was sutured with nylon thread. ln the right side incision the wound were close by approach and vaporized with C02 laser, defocusing, 8 watts in continuous mode. The wound healing was followed by clinical photographic taking at the times: immediately after the procedure, 24 hours, 3, 7, 14, and 21 days. The results showed an early delay of reparation in healing vaporized in comparison with the sutured one, however occurred 21 days both repair tissue showed the same clinical characteristic. This results suggested that the C02 laser can be used by eventual substitute of suture.

Resistência de união ao microcisalhamento de sistemas adesivos autocondicionates com graus de acidez distintos: efeito de diferentes tratamentos em substrato dentinário normal e hipermineralizado artificialmente

Pós-graduação em Ciências Odontológicas - FOAR

Caracterização da pulverização de mistura de tanque com diferentes pontas de jato plano

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Planejamento do plantio e da colheita de cana-de-açúcar utilizando técnicas matemáticas de otimização

Pós-graduação em Agronomia (Energia na Agricultura) - FCA

Conjuntos minimais de sistemas lineares por partes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of 808 nm low-level laser therapy in exercise-induced skeletal muscle fatigue in elderly women

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effects of Low-Level Laser Therapy on Biceps Braquialis Muscle Fatigue in Young Women

Objective: This study aims to investigate the effects of low-level laser therapy (LLLT) on biceps brachi muscular fatigue in 20 young females. Background data: Exhausting physical activity leads to muscular fatigue, which could decrease muscular strength, and may cause impairment in motor control and muscle pain. Several biochemical and biophysical resources have been studied in an attempt to accelerate the recovery of muscle fatigue. Among these, LLLT is emphasized. Methods: Twenty subjects were randomized in one laser group and one placebo group in two sessions of a crossover design experimental procedure; the second session taking place within 7 days of the first. In the first session, subjects underwent a collection of surface electromyographic (SEMG) data of the biceps brachii muscle, followed by active or placebo LLLT at the same muscle, followed then by another EMG sample of biceps brachii. Blood samples were collected five times during the experimental procedure. Second session procedures were identical to the first, with exception of LLLT, which was the opposite of the first session. The fatigue protocol consisted of 60sec of elbow flexion-extension movement performed with 75% of one maximum repetition. Blood lactate, EMG fatigue, and the number of elbow flexion-extension repetitions during the fatigue protocol were used to evaluate the effects of laser therapy (808nm wavelength, 100mW output power, power density of 35.7 W/cm(2), 70sec each point and 7J/point on eight points). Results: No statistical differences were found for eletromyographic fatigue and blood lactate values between groups. Mean numbers of elbow flexion-extension repetitions were 22.6 +/- 7.58 after placebo, and 25.1 +/- 9.89 after active LLLT group, but these differences were not statistically significant (p=0.342). Conclusions: LLLT had limited effects on delaying muscle fatigue in a young female sample, although a tendency was observed in the active laser group toward showing lower electromyography fatigue of biceps brachii muscle. No intergroup differences were found in the number of muscle contractions and lactate concentration.

Probing color coherence effects in pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Color Stability of Resin Used for Caries Infiltration After Exposure to Different Staining Solutions

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Er:YAG-Laser and Sodium Hypochlorite Influence on Bond to Dentin

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fabrication of Zinc Oxide Nanowires/Polymer Composites by Two-Photon Polymerization

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Clinical Trial Evaluating Color Change and Tooth Sensitivity Throughout and Following In-office Bleaching

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of Nd:YAG Laser on the Bond Strength of Self-etching and Conventional Adhesive Systems to Dental Hard Tissues

Purpose: The aim of this study was to investigate the influence of Nd:YAG laser on the shear bond strength to enamel and dentin of total and self-etch adhesives when the laser was applied over the adhesives, before they were photopolymerized, in an attempt to create a new bonding layer by dentin-adhesive melting.Material and Methods: One-hundred twenty bovine incisors were ground to obtain flat surfaces. Specimens were divided into two substrate groups (n=60): substrate E (enamel) and substrate D (dentin). Each substrate group was subdivided into four groups (n=15), according to the surface treatment accomplished: X (Xeno III self-etching adhesive, control), XL (Xeno III + laser Nd:YAG irradiation at 140 mJ/10 Hz for 60 seconds + photopolymerization, experimental), S (acid etching + Single Bond conventional adhesive, Control), and SL (acid etching + Single Bond + laser Nd:YAG at 140 mJ/10 Hz for 60 seconds + photopolymerization, experimental). The bonding area was delimited with 3-mm-diameter adhesive tape for the bonding procedures. Cylinders of composite were fabricated on the bonding area using a Teflon matrix. The teeth were stored in water at 37 degrees C/48 h and submitted to shear testing at a crosshead speed of 0.5 mm/min in a universal testing machine. Results were analyzed with three-way analysis of variance (ANOVA; substrate, adhesive, and treatment) and Tukey tests (alpha=0.05). ANOVA revealed significant differences for the substrate, adhesive system, and type of treatment: lased or unlased (p<0.05). The mean shear bond strength values (MPa) for the enamel groups were X=20.2 +/- 5.61, XL=23.6 +/- 4.92, S=20.8 +/- 4.55, SL=22.1 +/- 5.14 and for the dentin groups were X=14.1 +/- 7.51, XL=22.2 +/- 6.45, S=11.2 +/- 5.77, SL=15.9 +/- 3.61. For dentin, Xeno III self-etch adhesive showed significantly higher shear bond strength compared with Single Bond total-etch adhesive; Nd:YAG laser irradiation showed significantly higher shear bond strength compared with control (unlased).Conclusion: Nd:YAG laser application prior to photopolymerization of adhesive systems significantly increased the bond strength to dentin.