Structural changes and dynamic behaviour of vanadium oxide-based catalysts for gas-phase selective oxidations

Selective oxidation is one of the simplest functionalization methods and essentially all monomers used in manufacturing artificial fibers and plastics are obtained by catalytic oxidation processes. Formally, oxidation is considered as an increase in the oxidation number of the carbon atoms, then reactions such as dehydrogenation, ammoxidation, cyclization or chlorination are all oxidation reactions. In this field, most of processes for the synthesis of important chemicals used vanadium oxide-based catalysts. These catalytic systems are used either in the form of multicomponent mixed oxides and oxysalts, e.g., in the oxidation of n-butane (V/P/O) and of benzene (supported V/Mo/O) to maleic anhydride, or in the form of supported metal oxide, e.g., in the manufacture of phthalic anhydride by o-xylene oxidation, of sulphuric acid by oxidation of SO2, in the reduction of NOx with ammonia and in the ammoxidation of alkyl aromatics. In addition, supported vanadia catalysts have also been investigated for the oxidative dehydrogenation of alkanes to olefins , oxidation of pentane to maleic anhydride and the selective oxidation of methanol to formaldehyde or methyl formate [1]. During my PhD I focused my work on two gas phase selective oxidation reactions. The work was done at the Department of Industrial Chemistry and Materials (University of Bologna) in collaboration with Polynt SpA. Polynt is a leader company in the development, production and marketing of catalysts for gas-phase oxidation. In particular, I studied the catalytic system for n-butane oxidation to maleic anhydride (fluid bed technology) and for o-xylene oxidation to phthalic anhydride. Both reactions are catalyzed by systems based on vanadium, but catalysts are completely different. Part A is dedicated to the study of V/P/O catalyst for n-butane selective oxidation, while in the Part B the results of an investigation on TiO2-supported V2O5, catalyst for o-xylene oxidation are showed. In Part A, a general introduction about the importance of maleic anhydride, its uses, the industrial processes and the catalytic system are reported. The reaction is the only industrial direct oxidation of paraffins to a chemical intermediate. It is produced by n-butane oxidation either using fixed bed and fluid bed technology; in both cases the catalyst is the vanadyl pyrophosphate (VPP). Notwithstanding the good performances, the yield value didn’t exceed 60% and the system is continuously studied to improve activity and selectivity. The main open problem is the understanding of the real active phase working under reaction conditions. Several articles deal with the role of different crystalline and/or amorphous vanadium/phosphorous (VPO) compounds. In all cases, bulk VPP is assumed to constitute the core of the active phase, while two different hypotheses have been formulated concerning the catalytic surface. In one case the development of surface amorphous layers that play a direct role in the reaction is described, in the second case specific planes of crystalline VPP are assumed to contribute to the reaction pattern, and the redox process occurs reversibly between VPP and VOPO4. Both hypotheses are supported also by in-situ characterization techniques, but the experiments were performed with different catalysts and probably under slightly different working conditions. Due to complexity of the system, these differences could be the cause of the contradictions present in literature. Supposing that a key role could be played by P/V ratio, I prepared, characterized and tested two samples with different P/V ratio. Transformation occurring on catalytic surfaces under different conditions of temperature and gas-phase composition were studied by means of in-situ Raman spectroscopy, trying to investigate the changes that VPP undergoes during reaction. The goal is to understand which kind of compound constituting the catalyst surface is the most active and selective for butane oxidation reaction, and also which features the catalyst should possess to ensure the development of this surface (e.g. catalyst composition). On the basis of results from this study, it could be possible to project a new catalyst more active and selective with respect to the present ones. In fact, the second topic investigated is the possibility to reproduce the surface active layer of VPP onto a support. In general, supportation is a way to improve mechanical features of the catalysts and to overcome problems such as possible development of local hot spot temperatures, which could cause a decrease of selectivity at high conversion, and high costs of catalyst. In literature it is possible to find different works dealing with the development of supported catalysts, but in general intrinsic characteristics of VPP are worsened due to the chemical interaction between active phase and support. Moreover all these works deal with the supportation of VPP; on the contrary, my work is an attempt to build-up a V/P/O active layer on the surface of a zirconia support by thermal treatment of a precursor obtained by impregnation of a V5+ salt and of H3PO4. In-situ Raman analysis during the thermal treatment, as well as reactivity tests are used to investigate the parameters that may influence the generation of the active phase. Part B is devoted to the study of o-xylene oxidation of phthalic anhydride; industrially, the reaction is carried out in gas-phase using as catalysts a supported system formed by V2O5 on TiO2. The V/Ti/O system is quite complex; different vanadium species could be present on the titania surface, as a function of the vanadium content and of the titania surface area: (i) V species which is chemically bound to the support via oxo bridges (isolated V in octahedral or tetrahedral coordination, depending on the hydration degree), (ii) a polymeric species spread over titania, and (iii) bulk vanadium oxide, either amorphous or crystalline. The different species could have different catalytic properties therefore changing the relative amount of V species can be a way to optimize the catalytic performances of the system. For this reason, samples containing increasing amount of vanadium were prepared and tested in the oxidation of o-xylene, with the aim of find a correlations between V/Ti/O catalytic activity and the amount of the different vanadium species. The second part deals with the role of a gas-phase promoter. Catalytic surface can change under working conditions; the high temperatures and a different gas-phase composition could have an effect also on the formation of different V species. Furthermore, in the industrial practice, the vanadium oxide-based catalysts need the addition of gas-phase promoters in the feed stream, that although do not have a direct role in the reaction stoichiometry, when present leads to considerable improvement of catalytic performance. Starting point of my investigation is the possibility that steam, a component always present in oxidation reactions environment, could cause changes in the nature of catalytic surface under reaction conditions. For this reason, the dynamic phenomena occurring at the surface of a 7wt% V2O5 on TiO2 catalyst in the presence of steam is investigated by means of Raman spectroscopy. Moreover a correlation between the amount of the different vanadium species and catalytic performances have been searched. Finally, the role of dopants has been studied. The industrial V/Ti/O system contains several dopants; the nature and the relative amount of promoters may vary depending on catalyst supplier and on the technology employed for the process, either a single-bed or a multi-layer catalytic fixed-bed. Promoters have a quite remarkable effect on both activity and selectivity to phthalic anhydride. Their role is crucial, and the proper control of the relative amount of each component is fundamental for the process performance. Furthermore, it can not be excluded that the same promoter may play different role depending on reaction conditions (T, composition of gas phase..). The reaction network of phthalic anhydride formation is very complex and includes several parallel and consecutive reactions; for this reason a proper understanding of the role of each dopant cannot be separated from the analysis of the reaction scheme. One of the most important promoters at industrial level, which is always present in the catalytic formulations is Cs. It is known that Cs plays an important role on selectivity to phthalic anhydride, but the reasons of this phenomenon are not really clear. Therefore the effect of Cs on the reaction scheme has been investigated at two different temperature with the aim of evidencing in which step of the reaction network this promoter plays its role.

Studio di fenomeni d'instabilità gravitativa sui fondali marini, con particolare riferimento all'isola di Stromboli

In the last decade the interest for submarine instability grew up, driven by the increasing exploitation of natural resources (primary hydrocarbons), the emplacement of bottom-lying structures (cables and pipelines) and by the development of coastal areas, whose infrastructures increasingly protrude to the sea. The great interest for this topic promoted a number of international projects such as: STEAM (Sediment Transport on European Atlantic Margins, 93-96), ENAM II (European North Atlantic Margin, 96-99), GITEC (Genesis and Impact of Tsunamis on the European Coast 92-95), STRATAFORM (STRATA FORmation on Margins, 95-01), Seabed Slope Process in Deep Water Continental Margin (Northwest Gulf of Mexico, 96-04), COSTA (Continental slope Stability, 00-05), EUROMARGINS (Slope Stability on Europe’s Passive Continental Margin), SPACOMA (04-07), EUROSTRATAFORM (European Margin Strata Formation), NGI's internal project SIP-8 (Offshore Geohazards), IGCP-511: Submarine Mass Movements and Their Consequences (05-09) and projects indirectly related to instability processes, such as TRANSFER (Tsunami Risk ANd Strategies For the European region, 06-09) or NEAREST (integrated observations from NEAR shore sourcES of Tsunamis: towards an early warning system, 06-09). In Italy, apart from a national project realized within the activities of the National Group of Volcanology during the framework 2000-2003 “Conoscenza delle parti sommerse dei vulcani italiani e valutazione del potenziale rischio vulcanico”, the study of submarine mass-movement has been underestimated until the occurrence of the landslide-tsunami events that affected Stromboli on December 30, 2002. This event made the Italian Institutions and the scientific community more aware of the hazard related to submarine landslides, mainly in light of the growing anthropization of coastal sectors, that increases the vulnerability of these areas to the consequences of such processes. In this regard, two important national projects have been recently funded in order to study coastal instabilities (PRIN 24, 06-08) and to map the main submarine hazard features on continental shelves and upper slopes around the most part of Italian coast (MaGIC Project). The study realized in this Thesis is addressed to the understanding of these processes, with particular reference to Stromboli submerged flanks. These latter represent a natural laboratory in this regard, as several kind of instability phenomena are present on the submerged flanks, affecting about 90% of the entire submerged areal and often (strongly) influencing the morphological evolution of subaerial slopes, as witnessed by the event occurred on 30 December 2002. Furthermore, each phenomenon is characterized by different pre-failure, failure and post-failure mechanisms, ranging from rock-falls, to turbidity currents up to catastrophic sector collapses. The Thesis is divided into three introductive chapters, regarding a brief review of submarine instability phenomena and related hazard (cap. 1), a “bird’s-eye” view on methodologies and available dataset (cap. 2) and a short introduction on the evolution and the morpho-structural setting of the Stromboli edifice (cap. 3). This latter seems to play a major role in the development of largescale sector collapses at Stromboli, as they occurred perpendicular to the orientation of the main volcanic rift axis (oriented in NE-SW direction). The characterization of these events and their relationships with successive erosive-depositional processes represents the main focus of cap.4 (Offshore evidence of large-scale lateral collapses on the eastern flank of Stromboli, Italy, due to structurally-controlled, bilateral flank instability) and cap. 5 (Lateral collapses and active sedimentary processes on the North-western flank of Stromboli Volcano), represented by articles accepted for publication on international papers (Marine Geology). Moreover, these studies highlight the hazard related to these catastrophic events; several calamities (with more than 40000 casualties only in the last two century) have been, in fact, the direct or indirect result of landslides affecting volcanic flanks, as observed at Oshima-Oshima (1741) and Unzen Volcano (1792) in Japan (Satake&Kato, 2001; Brantley&Scott, 1993), Krakatau (1883) in Indonesia (Self&Rampino, 1981), Ritter Island (1888), Sissano in Papua New Guinea (Ward& Day, 2003; Johnson, 1987; Tappin et al., 2001) and Mt St. Augustine (1883) in Alaska (Beget& Kienle, 1992). Flank landslide are also recognized as the most important and efficient mass-wasting process on volcanoes, contributing to the development of the edifices by widening their base and to the growth of a volcaniclastic apron at the foot of a volcano; a number of small and medium-scale erosive processes are also responsible for the carving of Stromboli submarine flanks and the transport of debris towards the deeper areas. The characterization of features associated to these processes is the main focus of cap. 6; it is also important to highlight that some small-scale events are able to create damage to coastal areas, as also witnessed by recent events of Gioia Tauro 1978, Nizza, 1979 and Stromboli 2002. The hazard potential related to these phenomena is, in fact, very high, as they commonly occur at higher frequency with respect to large-scale collapses, therefore being more significant in terms of human timescales. In the last chapter (cap. 7), a brief review and discussion of instability processes identified on Stromboli submerged flanks is presented; they are also compared with respect to analogous processes recognized in other submerged areas in order to shed lights on the main factors involved in their development. Finally, some applications of multibeam data to assess the hazard related to these phenomena are also discussed.

Sviluppo di nuovi catalizzatori per la reazione di water gas shift a media temperatura

L’idrogeno è un elemento di elevato interesse economico, con una produzione industriale che supera i 55 x 1010 m3/anno e notevoli prospettive di sviluppo delle sue applicazioni. Attualmente l’idrogeno è prodotto principalmente in impianti di larga scala (circa 1000 m3/h) da combustibili fossili attraverso processi di steam reforming ed ossidazione parziale catalitica. Per aumentare la produzione di idrogeno un ruolo fondamentale è svolto dalla reazione di water gas shift (WGS) che abbatte il contenuto di CO, massimizzando la produzione di idrogeno. La reazione è condotta industrialmente in due stadi, operanti ad alta temperatura (HTS, circa 350 °C) e bassa temperatura (LTS, circa 250 °C), utilizzando rispettivamente catalizzatori a base di ferro o rame. Tuttavia, è evidente l’interesse per nuove formulazioni in grado di operare in un unico stadio a temperatura intermedia (MTS), mantenendo le caratteristiche ottimali di attività e stabilità. In questo lavoro di tesi, condotto in collaborazione con AIR LIQUIDE (F), è stato affrontato uno studio della reazione di WGS finalizzato allo sviluppo di nuove formulazioni attive e stabili nell’MTS. In particolare, sono stati sintetizzati precursori idrotalcitici Cu/Zn/Al (contenenti carbonati o silicati), con bassi contenuti di rame (diversamente da quanto riportato in letteratura), modulandone le proprietà chimico-fisiche, l’attività catalitica e la stabilità con il tempo di reazione. Si è osservato come i catalizzatori con minori contenuti di rame ed ottenuti da precursori contenenti carbonati mostrassero un’elevata attività e selettività nell’MTS, raggiungendo valori di conversione del CO analoghi a quelli all’equilibrio termodinamico già a 300 °C, indipendentemente dai valori del rapporto S/DG e del tempo di contatto. Tutti i catalizzatori mostrano un’elevata stabilità con il tempo di reazione, con incrementi del quantitativo del CO in uscita dopo 100h di circa lo 0,7 % v/v. I catalizzatori scaricati dopo le prove catalitiche evidenziano gli effetti dei processi di sinterizzazione (diminuzione dell’area superficiale ed incremento delle dimensioni dei cristalliti), la cui entità diminuisce al diminuire del contenuto di rame. Infine, confrontando l’attività dei migliori catalizzatori preparati in questo lavoro di tesi con quella di uno dei più utilizzati catalizzatori commerciali per la reazione di WGS a bassa temperatura, si sono osservati valori di attività analoghi, raggiungendo quelli di equilibrio per temperature  300°C, ma con una attività significativamente superiore nelle condizioni LTS, soprattutto considerando il valore del tempo di contatto inferiore a quelli comunemente utilizzati negli impianti industriali.

Influence of processing conditions on quality aspects of potato-based fresh pasta

Gnocchi is a typical Italian potato-based fresh pasta that can be either homemade or industrially manufactured. The homemade traditional product is consumed fresh on the day it is produced, whereas the industrially manufactured one is vacuum-packed in polyethylene and usually stored at refrigerated conditions. At industrial level, most kinds of gnocchi are usually produced by using some potato derivatives (i.e. flakes, dehydrated products or flour) to which soft wheat flour, salt, some emulsifiers and aromas are added. Recently, a novel type of gnocchi emerged on the Italian pasta market, since it would be as much similar as possible to the traditional homemade one. It is industrially produced from fresh potatoes as main ingredient and soft wheat flour, pasteurized liquid eggs and salt, moreover this product undergoes steam cooking and mashing industrial treatments. Neither preservatives nor emulsifiers are included in the recipe. The main aim of this work was to get inside the industrial manufacture of gnocchi, in order to improve the quality characteristics of the final product, by the study of the main steps of the production, starting from the raw and steam cooked tubers, through the semi-finished materials, such as the potato puree and the formulated dough. For this purpose the investigation of the enzymatic activity of the raw and steam cooked potatoes, the main characteristics of the puree (colour, texture and starch), the interaction among ingredients of differently formulated doughs and the basic quality aspects of the final product have been performed. Results obtained in this work indicated that steam cooking influenced the analysed enzymes (Pectin methylesterase and α- and β-amylases) in different tissues of the tuber. PME resulted still active in the cortex, it therefore may affect the texture of cooked potatoes to be used as main ingredient in the production of gnocchi. Starch degrading enzymes (α- and β-amylases) were inactivated both in the cortex and in the pith of the tuber. The study performed on the potato puree showed that, between the two analysed samples, the product which employed dual lower pressure treatments seemed to be the most suitable to the production of gnocchi, in terms of its better physicochemical and textural properties. It did not evidence aggregation phenomena responsible of hard lumps, which may occur in this kind of semi-finished product. The textural properties of gnocchi doughs were not influenced by the different formulation as expected. Among the ingredients involved in the preparation of the different samples, soft wheat flour seemed to be the most crucial in affecting the quality features of gnocchi doughs. As a consequence of the interactive effect of the ingredients on the physicochemical and textural characteristics of the different doughs, a uniform and well-defined split-up among samples was not obtained. In the comparison of different kinds of gnocchi, the optimal physicochemical and textural properties were detected in the sample made with fresh tubers. This was probably caused not only by the use of fresh steam cooked potatoes, but also by the pasteurized liquid eggs and by the absence of any kind of emulsifier, additive or preserving substance.

New catalysts for the water gas shift reaction at middle-temperature

H2 demand is continuously increasing since its many relevant applications, for example, in the ammonia production, refinery processes or fuel cells. The Water Gas Shift (WGS) reaction (CO + H2O = CO2 + H2 DeltaH = -41.1 kJ.mol-1) is a step in the H2 production, reducing significantly the CO content and increasing the H2 one in the gas mixtures obtained from steam reforming. Industrially, the reaction is carried out in two stages with different temperature: the first stage operates at high temperature (350-450 °C) using Fe-based catalysts, while the second one is performed at lower temperature (190-250 °C) over Cu-based catalysts. However, recently, an increasing interest emerges to develop new catalytic formulations, operating in a single-stage at middle temperature (MTS), while maintaining optimum characteristics of activity and stability. These formulations may be obtained by improving activity and selectivity of Fe-based catalysts or increasing thermal stability of Cu-based catalysts. In the present work, Cu-based catalysts (Cu/ZnO/Al2O3) prepared starting from hydrotalcite-type precursors show good homogeneity and very interesting physical properties, which worsen by increasing the Cu content. Among the catalysts with different Cu contents, the catalyst with 20 wt.% of Cu represents the best compromise to obtain high catalytic activity and stability. On these bases, the catalytic performances seem to depend on both metallic Cu surface area and synergetic interactions between Cu and ZnO. The increase of the Al content enhances the homogeneity of the precursors, leading to a higher Cu dispersion and consequent better catalytic performances. The catalyst with 20 wt.% of Cu and a molar ratio M(II)/M(III) of 2 shows a high activity also at 250 °C and a good stability at middle temperature. Thus, it may be considered an optimum catalyst for the WGS reaction at middle temperature (about 300 °C). Finally, by replacing 50 % (as at. ratio) of Zn by Mg (which is not active in the WGS reaction), better physical properties were observed, although associate with poor catalytic performances. This result confirms the important role of ZnO on the catalytic performances, favoring synergetic interactions with metallic Cu.

Produzione di idrogeno mediante reforming ciclico dell'etanolo

This work deals with a study on the feasibility of a new process, aimed at the production of hydrogen from water and ethanol (a compound obtained starting from biomasses), with inherent separation of hydrogen from C-containing products. The strategy of the process includes a first step, during which a metal oxide is contacted with ethanol at high temperature; during this step, the metal oxide is reduced and the corresponding metallic form develops. During the second step, the reduced metal compound is contacted at high temperature with water, to produce molecular hydrogen and with formation of the original metal oxide. In overall, the combination of the two steps within the cycle process corresponds to ethanol reforming, where however COx and H2 are produced separately. Various mixed metal oxides were used as electrons and ionic oxygen carriers, all of them being characterized by the spinel (inverse) structure typical of Me ferrites: MeFe2O4 (Me=Co, Ni, Fe or Cu). The first step was investigated in depth; it was found that besides the generation of the expected CO, CO2 and H2O, the products of ethanol anaerobic oxidation, also a large amount of H2 and coke were produced. The latter is highly undesired, since it affects the second step, during which water is fed over the pre-reduced spinel at high temperature. The behavior of the different spinels was affected by the nature of the divalent metal cation; magnetite was the oxide showing the slower rate of reduction by ethanol, but on the other hand it was that one which could perform the entire cycle of the process more efficiently. Still the problem of coke formation remains the greater challenge to solve.

Entwicklung und Charakterisierung von Gassterilisationsprozessen am Beispiel der Oberflächensterilisation mittels Wasserstoffperoxid und Ethylenoxid

Bei der Auswahl einer Sterilisationsmethode stehen, gemäß den Vorgaben des Europäischen Arzneibuches, die Sterilisation mittels Hitze (Dampf bzw. Heißluft) oder ionisierender Strahlung im Vordergrund. Diese so genannten Referenzverfahren verfügen neben einem breiten Wirkungsspektrum über eine hohe Effektivität und zeichnen sich durch eine gute Reproduzierbarkeit aus. Häufig jedoch verbieten die physikalisch – chemischen Eigenschaften des zu sterilisierenden Gutes eine Anwendung der Referenzverfahren. In derartigen Fällen muss nach geeigneten Alternativverfahren gesucht werden, will man eine aseptische Herstellung vermeiden. Besonders bei thermolabilen Gütern hat sich der Einsatz von gasförmigen Agenzien mit keimtötender Wirkung bewährt. Bei entsprechenden Rahmenbedingungen ist hier eine Sterilisation unterhalb der Raumtemperatur möglich. Die vorliegende Arbeit untersucht die Anwendbarkeit der Ethylenoxidsterilisation bzw. der Sterilisation mittels gasförmigen Wasserstoffperoxids (Vapour Phase Hydrogen Peroxide) auf verschiedene Materialoberflächen am Beispiel zweier aktueller Anwendungen aus der pharmazeutischen Industrie. Dabei werden die Vor- und Nachteile der beiden Verfahren aufgezeigt und in Relation zu den Referenzverfahren gestellt. Im Rahmen der abschließenden mikrobiologischen Leistungsbeurteilung beider Verfahren werden verschiedene methodische Ansätze, wie Halbzyklus und Fraction Negative Analysis zur Anwendung gebracht und bewertet.

Analisi del ciclo di vita di processi chimici industriali: applicazione alla sintesi di acrilonitrile mediante reazione di ammonossidazione

La green chemistry può essere definita come “l’utilizzo di una serie di principi che riducono o eliminano l’uso o la formazione di sostanze pericolose nella progettazione, produzione e applicazione di prodotti chimici”. . È in questo contesto che si inserisce la metodologia LCA (Life Cycle Assessment), come strumento di analisi e di valutazione. Lo scopo del presente lavoro di tesi è l’analisi degli impatti ambientali associati a processi chimici, ambito ancora poco sviluppato nella letteratura degli studi di LCA. Viene studiato e modellato il ciclo di vita (dall’ottenimento delle materie prime fino alla produzione del prodotto) della reazione di ammonossidazione per la produzione di acrilonitrile, valutando e comparando due alternative di processo: quella tradizionale, che utilizza propilene ( processo SOHIO), e le vie sintetiche che utilizzano propano, ad oggi poco sviluppate industrialmente. Sono stati pertanto creati sei scenari: due da propene (SOHIO FCC, con propene prodotto mediante Fluid Catalytic Cracking, e SOHIO Steam), e quattro da propano (ASAHI, MITSUBISHI, BP povero e ricco in propano). Nonostante la produzione dell’alcano abbia un impatto inferiore rispetto all’olefina, dovuto ai minori stadi di processo, dai risultati emerge che l’ammonossidazione di propano ha un impatto maggiore rispetto a quella del propene. Ciò è dovuto ai processi catalitici che utilizzano propano, che differiscono per composizione e prestazioni, rispetto a quelli da propene: essi risultano meno efficienti rispetto ai tradizionali, comportando maggiori consumi di reattivi in input . Dai risultati emerge che gli scenari da propano presentano maggiori impatti globali di quelli da propene per le categorie Cambiamento climatico, Formazione di materiale e Consumo di combustibili fossili. Invece per la categoria Consumo di metalli un impatto maggiore viene attribuito ai processi che utilizzano propene, per la maggior percentuale di metalli impiegata nel sistema catalitico, rispetto al supporto. L’analisi di contributo, eseguita per valutare quali sono le fasi più impattanti, conferma i risultati. Il maggior contributo per la categoria Consumo di combustibili fossili è ascrivibile ai processi di produzione del propano, dell’ammoniaca e del solfato di ammonio ( legato all’ammoniaca non reagita ). Stessi risultati si hanno per la categoria Cambiamento climatico, mentre per la categoria Formazione di materiale particolato, gli impatti maggiori sono dati dai processi di produzione del solfato di ammonio, del propano e dell’acido solforico (necessario per neutralizzare l’ammoniaca non reagita). Per la categoria Consumo di metalli, il contributo maggiore è dato dalla presenza del catalizzatore. È stata infine eseguita un’analisi di incertezza tramite il metodo Monte Carlo, verificando la riproducibilità dei risultati.

Advanced Waste-To-Energy Cycles

The increase in environmental and healthy concerns, combined with the possibility to exploit waste as a valuable energy resource, has led to explore alternative methods for waste final disposal. In this context, the energy conversion of Municipal Solid Waste (MSW) in Waste-To-Energy (WTE) power plant is increasing throughout Europe, both in terms of plants number and capacity, furthered by legislative directives. Due to the heterogeneous nature of waste, some differences with respect to a conventional fossil fuel power plant have to be considered in the energy conversion process. In fact, as a consequence of the well-known corrosion problems, the thermodynamic efficiency of WTE power plants typically ranging in the interval 25% ÷ 30%. The new Waste Framework Directive 2008/98/EC promotes production of energy from waste introducing an energy efficiency criteria (the so-called “R1 formula”) to evaluate plant recovery status. The aim of the Directive is to drive WTE facilities to maximize energy recovery and utilization of waste heat, in order to substitute energy produced with conventional fossil fuels fired power plants. This calls for novel approaches and possibilities to maximize the conversion of MSW into energy. In particular, the idea of an integrated configuration made up of a WTE and a Gas Turbine (GT) originates, driven by the desire to eliminate or, at least, mitigate limitations affecting the WTE conversion process bounding the thermodynamic efficiency of the cycle. The aim of this Ph.D thesis is to investigate, from a thermodynamic point of view, the integrated WTE-GT system sharing the steam cycle, sharing the flue gas paths or combining both ways. The carried out analysis investigates and defines the logic governing plants match in terms of steam production and steam turbine power output as function of the thermal powers introduced.

A chemical loop approach for methanol reforming

Over the past few years, the switch towards renewable sources for energy production is considered as necessary for the future sustainability of the world environment. Hydrogen is one of the most promising energy vectors for the stocking of low density renewable sources such as wind, biomasses and sun. The production of hydrogen by the steam-iron process could be one of the most versatile approaches useful for the employment of different reducing bio-based fuels. The steam iron process is a two-step chemical looping reaction based (i) on the reduction of an iron-based oxide with an organic compound followed by (ii) a reoxidation of the reduced solid material by water, which lead to the production of hydrogen. The overall reaction is the water oxidation of the organic fuel (gasification or reforming processes) but the inherent separation of the two semireactions allows the production of carbon-free hydrogen. In this thesis, steam-iron cycle with methanol is proposed and three different oxides with the generic formula AFe2O4 (A=Co,Ni,Fe) are compared in order to understand how the chemical properties and the structural differences can affect the productivity of the overall process. The modifications occurred in used samples are deeply investigated by the analysis of used materials. A specific study on CoFe2O4-based process using both classical and in-situ/ex-situ analysis is reported employing many characterization techniques such as FTIR spectroscopy, TEM, XRD, XPS, BET, TPR and Mössbauer spectroscopy.

Autenticazione d’origine, stima della Freshness quality e studio del profilo nutrizionale come elementi fondanti per la valorizzazione dell’alimento ittico

Questa tesi è dedicata alla qualità dell'alimento ittico in tre delle sue possibili accezioni. Dopo aver spiegato il complicato rapporto del consumatore con gli alimenti ittici e come l'Unione Europea abbia cercato di fare chiarezza al riguardo, gli argomenti di discussione saranno: Autenticazione d'origine La polpa di 160 esemplari di spigola (Dicentrachus labrax), suddivisi tra selvatici, allevati intensivamente e allevati estensivamente, provenienti dall'Italia e dall'estero per un totale di 18 fonti indagate, è stati analizzata individualmente per caratterizzarne la componente lipidica, isotopica e minerale e verificare le potenzialità di queste informazioni ai fini della autenticazione di origine in senso lato. Stima della Freshness Quality Numerosi lotti di seppia (Sepia officinalis), nasello (Merluccius merluccius) e triglia di fango (Mullus barbatus) sono stati sottoposti a due possibili modalità di stoccaggio sotto ghiaccio fondente, per indagare come, nell’arco della loro vita commerciale, ne evolvessero importanti connotati chimici (cataboliti dell’ATP e loro rapporti), fisici (proprietà dielettriche dei tessuti) e sensoriali (Quality Index Methods specie-specifici. Studio del profilo nutrizionale La componente lipidica di numerosi lotti di mazzancolla (Penaeus kerathurus), canocchia (Squilla mantis) e seppia (Sepia officinalis) è stata caratterizzata allo stato crudo e dopo cottura secondo tecniche “dedicate” per stabilire il contributo di queste matrici come fonte di acidi grassi polinsaturi della serie omega 3 e per pervenire alla determinazione dei loro coefficienti di ritenzione vera.

Sistemi catalitici per la reazione di water - gas shift a media temperatura

Negli ultimi anni l’interesse nei confronti dell’H2 è cresciuto notevolmente per l’aumento della richiesta energetica mondiale. Uno dei processi più importanti per la produzione di H2 utilizza la reazione di Water-Gas Shift (WGS) per il trattamento delle correnti in uscita dai processi di steam reforming o di ossidazione parziale catalitica. CO + H2O  CO2 + H2 ∆H0298 = -41,2 KJ/mol Sono quindi stati sviluppati sistemi catalitici attivi nella reazione di WGS a media temperatura (circa 300 °C). Partendo da sistemi catalitici a base di Cu/Zn/Al, ottenuti da precursori idrotalcitici e sviluppati in lavori di tesi precedenti, sono state effettuate modifiche nella composizione al fine di aumentarne l’attività e la stabilità. L’aggiunta di piccole quantità di Mg ha un effetto positivo sull’attività dei sistemi catalitici, con effetti più evidenti a 250 °C. Tuttavia, l’aumento del contenuto di Mg, sebbene migliori le proprietà fisiche del catalizzatore (area superficiale e dispersione del Cu) sia del campione calcinato che di quello scaricato dopo reazione, peggiora drasticamente l’attività catalitica. L’aggiunta di piccole quantità di Mg sembra portare alla stabilizzazione della specie attiva Cu+ e promuovere un meccanismo redox superficiale (Cu0 e Cu+). E’ possibile correlare la conversione del CO con il rapporto ZnO/Cu, confermando il ruolo nella reazione di WGS dell’interazione Cu0/ZnO libero. La sostituzione di Mg con Ba comporta un miglioramento delle prestazioni catalitiche, in particolare nelle condizioni MTS (300 °C), suggerendo una più facile dissociazione dell’acqua legata alla stabilizzazione degli ossidrili da parte dei siti basici. È però accompagnato da una diminuzione della stabilità nelle condizioni di reazione. L’aggiunta di piccole quantità di La, Ce o Zr (con un rapporto Al/R = 50 mol/mol) incrementa la stabilità termica, sia in termini di proprietà fisiche che di attività catalitica. A seguito dei cicli termici di invecchiamento accelerato, infatti, non si riscontrano importanti diminuzioni di attività catalitica, evidenziando un’elevata stabilità della fase attiva.

3D nanostructured microcarriers for cell therapy in regenerative medicine

Supercritical Emulsion Extraction technology (SEE-C) was proposed for the production of poly-lactic-co-glycolic acid microcarriers. SEE-C operating parameters as pressure, temperature and flow rate ratios were analyzed and the process performance was optimized in terms of size distribution and encapsulation efficiency. Microdevices loaded with bovine serum insulin were produced with different sizes (2 and 3 µm) or insulin charges (3 and 6 mg/g) and with an encapsulation efficiency of 60%. The microcarriers were characterized in terms of insulin release profile in two different media (PBS and DMEM) and the diffusion and degradation constants were also estimated by using a mathematical model. PLGA microdevices were also used in a cultivation of embryonic ventricular myoblasts (cell line H9c2 obtained from rat) in a FBS serum free medium to monitor cell viability and growth in dependence of insulin released. Good cell viability and growth were observed on 3 µm microdevices loaded with 3 mg/g of insulin. PLGA microspheres loaded with growth factors (GFs) were charged into alginate scaffold with human Mesenchimal Steam Cells (hMSC) for bone tissue engineering with the aim of monitoring the effect of the local release of these signals on cells differentiation. These “living” 3D scaffolds were incubated in a direct perfusion tubular bioreactor to enhance nutrient transport and exposing the cells to a given shear stress. Different GFs such as, h-VEGF, h-BMP2 and a mix of two (ratio 1:1) were loaded and alginate beads were recovered from dynamic (tubular perfusion system bioreactor) and static culture at different time points (1st, 7th, 21st days) for the analytical assays such as, live/dead; alkaline phosphatase; osteocalcin; osteopontin and Van Kossa Immunoassay. The immunoassay confirmed always a better cells differentiation in the bioreactor with respect to the static culture and revealed a great influence of the BMP-2 released in the scaffold on cell differentiation.

Vanillin production from ferulic acid with Pseudomonas fluorescens BF13-1p4

Bioconversion of ferulic acid to vanillin represents an attractive opportunity for replacing synthetic vanillin with a bio-based product, that can be label “natural”, according to current food regulations. Ferulic acid is an abundant phenolic compound in cereals processing by-products, such as wheat bran, where it is linked to the cell wall constituents. In this work, the possibility of producing vanillin from ferulic acid released enzymatically from wheat bran was investigated by using resting cells of Pseudomonas fluorescens strain BF13-1p4 carrying an insertional inactivation of vdh gene and ech and fcs BF13 genes on a low copy number plasmid. Process parameters were optimized both for the biomass production phase and the bioconversion phase using food-grade ferulic acid as substrate and the approach of changing one variable while fixing the others at a certain level followed by the response surface methodology (RSM). Under optimized conditions, vanillin up to 8.46 mM (1.4 g/L) was achieved, whereas highest productivity was 0.53 mmoles vanillin L-1 h-1). Cocktails of a number of commercial enzyme (amylases, xylanases, proteases, feruloyl esterases) combined with bran pre-treatment with steam explosion and instant controlled pressure drop technology were then tested for the release of ferulic acid from wheat bran. The highest ferulic acid release was limited to 15-20 % of the ferulic acid occurring in bran, depending on the treatment conditions. Ferulic acid 1 mM in enzymatic hydrolyzates could be bioconverted into vanillin with molar yield (55.1%) and selectivity (68%) comparable to those obtained with food-grade ferulic acid after purification from reducing sugars with a non polar adsorption resin. Further improvement of ferulic acid recovery from wheat bran is however required to make more attractive the production of natural vanillin from this by-product.

Innovative processes for syngas production

The research of new advanced processes for syngas production is a part of a European project for the production of a new Gas to Liquid Process (NextGTL). The crucial points in the production of GTL process are the energy required for the air separation used in autothermal reforming or the heat required for steam reforming and the efficiency in carbon utilization. Therefore a new multistep oxy-reforming process scheme was developed at lower temperature with intermediate H2 membrane separation to improve the crucial parameter. The process is characterized by a S/C of 0.7 and O2/C of 0.21 having a smoothed temperature profile in which kinetic regime is easily obtained. Active catalysts for low temperature oxy-reforming process have been studied working at low pressure to discriminate among the catalyst and at high pressure to prove it on industrial condition. It allows the selection of the Rh as active phase among single and bimetallic VIII group metal. The study of the matrix composition and thermal treatment has been carried out on Rh-Mg/Al hydrotalcite selected as reference catalyst. The research to optimize the catalyst lead to enhanced performances through the identification of a limitation of the Rh reduction from the oxides matrix as key point to increase the Rh performances. The Rh loading have been studied to allow the catalyst scale up for pilot process in Chieti in a shape of Rh-HT on honeycomb ceramic material. The developed catalyst has enhanced methane conversion in a inch diameter monolith reactor if compared with the semi-industrial catalyst chosen in the project as the best reference.