Effect of brood source on the growth of rohu (Labeo rohita Ham.) fingerlings reared in glass tanks with formulated diets

A 60 day long feeding trial was conducted in an indoor static water system with rohu fingerlings (Labeo rohita Ham.) originating from wild brood, private and public hatcheries (denoted as A B and C respectively). They were fed on formulated diet having 34% crude protein level using indigenous ingredients. The effect of brood source on growth as well as their responses to formulated diet was observed. On the basis of the observed growth rate, food conversion ratio, protein efficiency ratio, apparent net protein utilization and apparent protein digestibility, fingerling source A showed significantly (p<0.05) higher growth, while the sources B and C produced no significantly different (p>0.05) in terms of these parameters. The results of the present study demonstrated that the fingerlings of wild source were of best quality in terms of growth and food utilization in comparison to those had the sources from hatcheries.

Culture feasibility of african catfish (Clarias gariepinus Lin.) fry in glass tank and synthetic hapa system using supplemental diets

An experiment was carried out with 1 0 days old Clarias gariepinus fry over a period of 42 days to determine the effects of different feeds on growth and survival of African catfish fry in glass tanks. The experiment was designed into four treatments each having three replications. Thus treatment 1 (T1) was named as Tank Tubifex (TT) and treatment 2 (T2) as Tank Sabinco (TS), treatment 3 as Pond Tubifex (PT), and treatment 4 (T4) as Pond Sabinco (PS). Live Tubifex (protein levels 64.48%) was supplied to treatments 1 and 3 and rest of the treatments were supplied Sabinco starter-1 (protein levels 40.13%). The highest and the lowest growth in total length and weight were 12.90cm, 18.77g and 6.17cm, 4.04g recorded from the treatments 3 and 2, respectively. Growth of catfish fry under treatment 3 in terms of both length and weight were significantly higher (P<0.01) than those of the other treatments. However treatment 2 showed the significantly lowest (P<0.01) growth performance among the various treatments. The highest survival rate (92%) was also obtained with treatment 3. Tubifex proved to be the best larval feed in respect of growth and survival rate.

Transitions in the erosive wear behavior of a glass-ceramic

The mechanisms of material removal were investigated during the erosive wear of a glass-ceramic. The effects of erodent particle shape, velocity and angle were studied. Single impacts and incremental erosion tests were performed, to study the development of surface features and to elucidate the mechanisms of material removal. It was found that transitions in mechanism occurred which depended on the particle shape, impact velocity and impact angle. The mechanisms of material removal, for erosion by silica sand, changed from fine scale fracture and plastic processes below a transition point to large-scale cracking of the surface above. Spherical glass beads caused wear dominated by fatigue, with a very strong dependence of wear rate on the impact conditions. This work indicates that laboratory erosion testing of glass-ceramic and other brittle materials should reflect the conditions present in practice, and that account must be taken of possible changes in wear mechanisms.

Failure mechanisms and toughness of Al2O3 ductile-particle toughened ceramics and SiC fibre-ceramic composites

The development of high performance ceramics and ceramic composites often relies on assumptions about their behaviour during loading and at failure. A crucial influence on the mechanical properties of these materials is the degree of sub-critical cracking, which post mortem investigations cannot adequately reveal. Hence a clear picture of the dynamic micromechanisms of cracking is required if applications of fracture and damage mechanics to theoretical models is to be meaningful.

Waveguide lasers in Er:Yb-doped phosphate glass fabricated by femtosecond laser writing

Advanced waveguide lasers, operating both in continuous wave and pulsed regimes, have been realized in an active phosphate glass by direct writing with femtosecond laser pulses. Stable single mode operation was obtained; the laser provided more than 50 m W in single longitudinal and transverse mode operation with 21% slope efficiency. Furthermore, by combining a high gain waveguide and an innovated fiber-pigtailed saturable absorber based on carbon nanotubes, a mode-locked ring laser providing transform limited 1.6 ps pulses was demonstrated. © 2007 IEEE.

Fabrication and mechanical property of carbon nanotube/metal composites

Carbon nanotubes (CNTs) are known to exhibit extraordinary mechanical properties such as high tensile strength, the highest Young modulus etc. These, combining with their large aspect ratio, make CNTs an excellent additive candidate to complement or substitute traditional carbon black or glass fiber fillers for the development of nano-reinforced composites. CNTs have thus far been used as additives in polymers, ceramics and metals to be pursued on practical applications of their composites. © 2010 IEEE.

Experiments with fibre-glass sheathing as a protection against marine wood-boring organisms

Wooden test panels of different species of wood sheathed with fibre-glass reinforced plastic were subjected to immersion tests along with corresponding controls in Cochin Port area and the effect of the protective coating studied.

Mode-locked and single-longitudinal-mode waveguide lasers fabricated by femtosecond laser pulses in Er:Yb-doped phosphate glass

Mode-locked and single-longitudinal-mode waveguide lasers, manufactured by femtosecond laser writing in Er-Yb-doped phosphate glasses, are presented. Transform-limited 1.6-ps pulses and a cw output power exceeding 50 mW have been obtained in the two regimes. © 2007 Optical Society of America.

Structural use of glass

... .10) i=1 i=1 in which I is the number of data points included in the fit. ... the least squares method can be used to estimate parameters of any model, ...