Powder Diffraction of Components Subject to Corrosion in Fuse Cutouts with CeramicInsulation

Aiming identification of the components most affected by corrosion under saline environment conditions, we have carried out X-ray diffraction measurements in ceramic and bond materials, all in the powder form. The ceramic is analyzed before and after thermal annealing at 1000 degrees C, showing the same DRX peaks, although better defined after annealing. Identification suggests the presence of Al(6)Si(2)O(13) (Mullite) and SiO(2) (Quartz). Analysis of the junction (bond) material shows similar peaks, but a metallic preponderance is observed. Thermal annealing of the junction is done at much lower temperature, because it melts in the range 135 degrees C-170 degrees C, when a whitish smoke begins to show up along with strong sulfur odor.

Atributos químicos, produção e qualidade do capim braquiária em solos corrigidos com calcário e escória silicatada

As pastagens constituem a base dos sistemas de produção de bovinos, o que evidencia sua importância e a necessidade de outras práticas de manejo que resultem em maior eficiência desses sistemas. Assim, este trabalho teve como objetivo avaliar os atributos químicos do solo (pH, Ca, Mg e H+Al), o potencial produtivo e a composição química do capim braquiária (Brachiaria decumbens Stapf) em solo corrigido com diferentes doses de calcário e escória silicatada. O experimento foi conduzido em ambiente protegido no período de 2006/2007, na UNESP de Ilha Solteira. Foram testadas cinco doses de calcário e escória silicatada, 0,0; 0,5; 1,0; 1,5; 2,0 vezes a dose recomendada. O delineamento experimental foi inteiramente casualizado, com quatro repetições. Avaliou-se a composição química do solo após incubação dos corretivos, o perfilhamento, a matéria seca, proteína, FDN (fibra em detergente neutro) e FDA (fibra em detergente ácido). Ambos os corretivos proporcionaram ao solo efeito positivo em relação ao pH e teores de cálcio e magnésio. As variáveis matéria seca e FDA não foram influenciadas significativamente pelos tipos e doses de corretivos.

Avaliação oxidativa do biodiesel de pinhão manso em diferentes processos de purificação

The objective of this study was to analyze the oxidative stability of biodiesel from jatropha obtained from different purification processes, three wet processes with different drying (in a vacuum oven, conventional oven and in anhydrous sodium sulfate) and dry (purification with magnesium silicate adsorbent). Raw materials of different qualities (jatropha crop ancient and recent crop) were used. The Jatropha oil was extracted by mechanical extraction and refined. The Jatropha biodiesel was obtained by the transesterification reaction in ethyl route using alkaline catalysis. The biodiesel samples were characterized by analysis of water content, carbon residue, Absorption Spectroscopy in the Infrared Region and Thermogravimetry. Thermogravimetric curves of purified PUsv* PUsq* and had higher initial decomposition temperatures, indicating that the most stable, followed by samples PU* and PUSC*. Besides the sample SP* is a smaller initial temperature, confirming the sample without purification to be less thermally stable. The percentage mass loss of the purified samples showed conversion of about 98.5%. The results of analyzes carbon residue and infrared suggested that contamination by impurities is the main factor for decreased oxidative stability of biodiesel. The oxidative stability was assessed from periodic monitoring, using the techniques of Rancimat, peroxide index, acid value and Pressurized Differential Scanning Calorimetry. Samples of biodiesel from jatropha which showed better oxidative stability were of the best quality raw material and wet scrubbing: PUsq* with dry chemical, using anhydrous sodium sulfate and PUsv* with vacuum drying, which had oxidative stability 6 hours in Rancimat time 0 days, within the limits established by the Technical Regulation No. 4/2012 of the ANP, without the addition of antioxidant, suggesting that these procedures the least influence on the oxidative stability of biodiesel

Efeito da escória de siderurgia e calcário na disponibilidade de fósforo de um Latossolo Vermelho-Amarelo cultivado com cana-de-açúcar

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Efeito residual da escória de siderurgia como corretivo de acidez do solo na soqueira de cana-de-açúcar

A escória de siderurgia, como material corretivo e efeito residual prolongado, pode beneficiar culturas de ciclo longo, a exemplo da cana-de-açúcar, minimizando a queda de produção ao longo do ciclo produtivo. Este trabalho objetivou avaliar diferentes níveis de saturação por bases, utilizando, como corretivo do solo, a escória de siderurgia, comparando-a com calcário calcítico, nas alterações de alguns atributos químicos do solo, bem como na resposta da soqueira da cana-de-açúcar. Para isto, realizou-se um experimento com a variedade SP 80-1842, durante o terceiro e o quarto corte, nos anos agrícolas 2000/01 e 2001/02. Os tratamentos, dispostos em blocos casualizados, em esquema fatorial com quatro repetições, constaram de duas fontes de corretivos, calcário calcítico e escória de siderurgia, e quatro níveis de correção, estimados pelo método da saturação por bases (V %): testemunha (sem correção) e com correção para V % de 50; 75 e 100, tendo sido tais corretivos aplicados na época do plantio da cana-de-açúcar. O calcário calcítico e a escória de siderurgia promoveram efeito residual benéfico, após 48 meses da aplicação, na correção da acidez do solo e na elevação do valor da saturação por bases; a maior dose de calcário causou efeito depressivo no perfilhamento, no número de colmos industrializáveis e na produção da cana-de-açúcar, fato não observado com uso da escória de siderurgia; a aplicação da escória de siderurgia e do calcário, em pré-plantio, promoveu efeito residual positivo na produção da soqueira de cana-de-açúcar.

Produção e composição bromatológica da forragem do capim-mombaça (Panicum maximum Jacq.), submetidos a diferentes fontes e doses de corretivo de acidez

The experiment was carried in protected (greenhouse) atmosphere, in University of Engineering, UN-ESP of Ilha Solteira-SP, with the objective of evaluating sources (limestone and calcium silicate slag) and doses (0,0 0,5 1,0 1,5 2,0 times the recommended dose) of corrective in the bromatolouic composition, tillering and production of dry matter of the grass mombaca (Nuncio? maximum Jacq.). The lineation was completely randomized design, with four repetitions. It was evaluated the tiller number, the production of dry matter, the gross protein, neutral detergent fiber (NDF) and acid detergent fiber (ADF). The corrective influenced the tillering in almost all of the countings. The limestone provided larger production of dry matter in the doses of 1,5 and 2,0 times the recommended dose. The bromatologic composition of the forage was not influenced by the corrective and doses.

Produtividade e qualidade industrial do arroz de terras altas em função da disponibilidade hídrica e adubação

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Petrologia dos granitóides brasilianos associados à zona de cisalhamento Remígio-Pocinhos(PB)

The Brasiliano Cycle in the Seridó Belt (NE Brazil) is regarded mostly as a crustal reworking event, characterized by transcurrent or transpressional shear zones which operated under high temperature and low pressure conditions. In the eastern domain of this belt- the so-called São José de Campestre Massif (SJCM), a transtensional deformation regime is evidenced by extensional components or structures associated to the strikeslip shear zones. The emplacement of the Neoproterozoic Brasiliano granitoids is strongly controled by these discontinuities. Located in the southern border of the SJCM, the Remígio-Pocinhos shear zone (RPSZ) displays, in its northern half, top to the SW extensional movement which progressively grade, towards its southern half, to a dextral strike-slip kinematics, defining a negative semi-flower structure. This shear zone is overprinted upon allocthonous metasediments of the Seridó Group and an older gneiss-migmatite complex, both of which containing metamorphic parageneses from high amphibolite to granulite facies (the latter restricted to the strike-slip zone), defining the peak conditions of deformation. Several granitoid plutons are found along this structure, emplaced coeval with the shearing event. Individually, such bodies do not exceed 30 km2 in outcropping area and are essentially parallel to the trend of the shear zone. Petrographic, textural and geochemical data allow to recognize five different granitoid suites along the RPSZ: porphyritic granites (Serra da Boa Vista and Jandaíra), alkaline granites (Serra do Algodão and Serra do Boqueirão) and medium to coarse-grained granites (Olivedos) as major plutons, while microgranite and aluminous leucogranite sheets occur as minor intrusions. The porphyritic granites are surrounded by metasediments and present sigmoidal or en cornue shapes parallel to the trend of the RPSZ, corroborating the dextral kinematics. Basic to intermediate igneous enclaves are commonly associated to these bodies, frequently displaying mingling textures with the host granitoids. Compositionally these plutons are made up by titanite-biotite monzogranites bearing amphibole and magnetite; they are peraluminous and show affinities to the monzonitic, subalkaline series. Peraluminous, ilmenite-bearing biotite monzogranites and titanite-biotite monzogranites correspond, respectivally, to the Olivedos pluton and the microgranites. The Olivedos body is hosted by metasediments, while the microgranites intrude the gneiss-migmatite complex. Being highly evolved rocks, samples from these granites plot in the crustal melt fields in discrimination diagrams. Nevertheless, their subtle alignment also looks consistent with a monzonitic, subalkaline affinity. These chemical parameters make them closer to the I-type granites. Alkaline, clearly syntectonic granites are also recognized along the RPSZ. The Serra do Algodão and Serra do Boqueirão bodies display elongated shapes parallel to the mylonite belt which runs between the northern, extensional domain and the southern strike-slip zone. The Serra do Algodão pluton shows a characteristic isoclinal fold shape structure. Compositionally they encompass aegirine-augite alkali-feldspar granites and quartz-bearing alkaline syenite bearing garnet (andradite) and magnetite plus ilmenite as opaque phases. These rocks vary from meta to peraluminous, being correlated to the A-type granites. Aluminous leucogranites bearing biotite + muscovite ± sillimanite ± garnet (S-type granites) are frequent but not volumetrically important along the RPSZ. These sheet-like bodies may be folded or boudinaged, representing partial melts extracted from the metasediments during the shear zone development. Whole-rock Rb-Sr isotope studies point to a minimum 554��10 Ma age for the crystalization of the porphyritic granites. The alkaline granites and the Olivedos granite produced ca. 530 Ma isochrons which look too young; such values probably represent the closure of the Rb-Sr radiometric clock after crystallization and deformation of the plutons, at least 575 Ma ago (Souza et al. 1998). The porphyritic and the alkaline granites crystallized under high oxygen fugacity conditions, as shown by the presence of both magnetite and hematite in these rocks. The presence of ilmenite in the Olivedos pluton suggests less oxidizing conditions. Amphibole and amphibole-plagioclase thermobarometers point to minimum conditions, around 750°C and 6 Kbars, for the crystallization of the porphyritic granites. The zirconium geothermometer indicates higher temperatures, in the order of 800°C, for the porphyritic granites, and 780°C for the Olivedos pluton. Such values agree with the thermobarometric data optained for the country rocks (5,7 Kbar and 765°C; Souza et al. 1998). The geochemical and isotope data set point to a lower crustal source for the porphyritic and the alkaline granites. Granulite facies quartz diorite to tonalite gneisses, belonging or akin to the gneiss-migmatite complex, probably dominate in the source regions. In the case of the alkaline rocks, subordinate contributions of mantle material may be present either as a mixing magma or as a previously added component to the source region. Tonalite to granodiorite gneisses, with some metasedimentary contribution, may be envisaged for the Olivedos granite. The diversity of granitoid rocks along the RPSZ is explained by its lithospheric dimension, allowing magma extraction at different levels, from the middle to lower crust down to the mantle. The presence of basic to intermediate enclaves, associated to the porphyritic granites, confirm the participation of mantle components in the magma extraction system along the RPSZ. This mega-structure is part of the network of Brasiliano-age shear zones, activated by continental collision and terrane welding processes at the end of the Neoproterozoic

Pirometamorfismo nos arenitos da Formação Açu, Bacia Potiguar, NE do Brasil

Pyrometamorphism results from conditions of high temperatures and very low pressures provoked by the intrusion of hypabyssal basic bodies into sedimentary or metassedimentary hosting rocks. The onshore portion of the Potiguar Basin in NE Brazil offers examples of this type of metamorphism nearby the contacts of Paleogene to Neogene plugs, sills and dikes of diabases and basalts crosscutting sandstones, siltstones and shales of the Açu Formation (Albian-Cenomanian). The thermal effects over these rocks are reflected on textures and minerals assemblages that characterize the sanidinite facies of metamorphism, often with partial melting of the feldspathic and mica-rich matrix. The liquid formed is potassic and peraluminous, with variably colored rhyolitic glass (colorless, yellow, brown) comprising microcrystals of tridymite, sanidine and clinoenstatite, besides residual detrital clasts of quartz and rarely zircon, staurolite and garnet. Lenses of shale intercalated within the sandstones display crystallites of Fe-cordierite (sekaninaite), mullite, sanidine, armalcolite (Fe-Ti oxide) and brown spinel. The rocks formed due to the thermal effect of the intrusions are called buchites for which two types are herein described: a light one derived from feldspathic sandstone and siltstone protoliths; and a dark one derived from black shale protoliths. Textures indicating partial melting and minerals such as sanidine, mullite, tridymite and armalcolite strongly demonstrate that during the intrusion of the basic bodies the temperature reached 1,000-1,150°C, and was followed by quenching. Cooling of the interstitial melts has as consequences the closure of pores and decrease of the permeability of the protolith, which varies from about 17-11% in the unaffected rocks to zero in the thermally modified types. Although observed only at contacts and over small distances, the number of basic intrusions hosted within the Potiguar Basin in both onshore and offshore portions leaves opened the possibility of important implications of the thermal effects over the hydrocarbon exploration in this area as well in other Cretaceous and Paleozoic basins in Brazil

Aplicação de escória siderúrgica calcário e ureia em latossolo cultivado com arroz

A escória de siderurgia é um silicato de cálcio e fonte de silício, que tem ação corretiva da acidez do solo semelhante à do calcário. Apesar do seu grande potencial de uso como corretivo e fertilizante, existem poucas informações sobre seus efeitos nos atributos químicos do solo. O estudo foi realizado com a cultura do arroz, objetivando-se avaliar os efeitos da aplicação da escória de siderurgia, calcário e ureia nas alterações dos atributos químicos de um Latossolo Vermelho distrófico. Os tratamentos constaram da combinação de duas fontes de materiais corretivos (calcário e escória de siderurgia), em três doses (1,3 g dm-3 2,6 g dm-3 e 5,2 g dm-3; três doses de N (80 mg dm-3 160 mg dm-3e 320 mg dm-3, aplicadas na forma de ureia; e uma testemunha, dispostas em blocos casualizados, em esquema fatorial, com quatro repetições. Após o período de 90 dias de incubação do solo e 120 dias de cultivo da cultura do arroz, coletaram-se amostras do solo, para análise química. A escória de siderurgia foi viável como corretivo de acidez do solo e a adubação nitrogenada em arroz contribuiu para incrementos na acidez do solo, diminuindo a saturação por bases e o teor de Ca e Mg. A aplicação de escória de siderurgia favoreceu a disponibilidade de silício, entretanto, quando associada à adubação nitrogenada, não alterou o teor deste elemento no solo.

Tissue response to experimental dental cements prepared from a modified power glass composition

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Desenvolvimento da aveia branca e disponibilidade de fósforo em razão da aplicação de silicato de potássio

A aplicação de silicato de potássio pode aumentar a disponibilidade de fósforo no solo, além de influenciar no crescimento da aveia branca. Objetivou-se neste trabalho avaliar o efeito da aplicação de doses de silicato de potássio no solo no desenvolvimento da aveia branca e na disponibilidade de fósforo. O delineamento experimental foi inteiramente ao acaso, em esquema fatorial 2 x 4, com seis repetições. Os tratamentos foram 20 e 200 mg dm-3 de P2O5 combinados com 0, 150, 300 e 450 mg dm-3 de Si, aplicados por ocasião da semeadura. Após a colheita, determinaram-se a matéria seca de folhas + colmos, das panículas e o total da parte aérea. A palha das panículas foi separada para avaliação dos teores de P e Si nas folhas + colmos, grãos e palha das panículas. As concentrações de Si e P no solo foram avaliadas após colheita das plantas. A aplicação de silicato aumenta os teores de Si no solo e influencia na maior disponibilidade de fósforo. A matéria seca de folhas + colmos é incrementada pelo silicato quando os teores iniciais de P são baixos. Mesmo com a dose elevada de P, a aplicação de silicato aumenta a disponibilidade de P no solo e a absorção pelas plantas. Os teores de Si na palha das panículas, folhas + colmos e grãos são influenciados pela maior disponibilidade do elemento no solo.

Influence of atypical pluviosity on phytoplankton assemblages in a stretch of a large sub-tropical river (Brazil)

This study aimed to evaluate the influence of alterations in pluviosity and ecological variables on microphytoplankton (> 20 mu m) structure (composition, richness, diversity, and abundance) and its biomass (chlorophyll-a), comparing different regions in a stretch of the low Igua double dagger u River and in some tributaries. Phytoplankton was sampled in 10 stations (5 in Igua double dagger u River and 5 in tributaries) during a dry period (April/2004) and an atypical rainy period (June/2004). The conductivity showed significant difference among the sampling points. Temperature, dissolved oxygen, pH, silicate, and nitrate showed significant differences between the dry and wet periods. Phytoplankton was composed of 149 taxa, and the most representative class was Chlorophyceae (71 taxa), followed by Bacillariophyceae (35 taxa), and Cyanophyceae (25 taxa). During the rainy period, stations of Igua double dagger u River showed higher taxa number and total density compared to the tributaries, but the values were similar in the dry period. Tributaries presented higher diversity and equitability in both periods. Except by two stations in Igua double dagger u River, the higher taxa number, densities and biomass occurred in the dry period, associated to low levels of suspended matter. The canonical correspondence analysis indicated the dominance of Bacillariophyceae and Chrysophyceae in the rainy period related to nitrate and suspended matter. Two other groups were observed in the dry period: one formed by Cyanophyceae, Dinophyceae, and Rhodophyceae, related to temperature and nitrite and other by Euglenophyceae and Chlorophyceae related to total phosphorus and silicate. The groups suggest adequate conditions of the physical, chemical and climatic factors to the establishment of the algae classes. Phytoplanktonic assemblages responded quickly to the environmental regional variations under strong influence of pluviosity, while in the dry period, homogeneity among stations and environmental variables was observed. The importance of climatic events is relevant in ecological studies in a temporal scale.

Compositional and structural changes at the anodic surface of thermally poled soda-lime float glass

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Uranium distribution and radon exhalation from Brazilian dimension stones

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)