An experimental and computational study of the formation of a streamwise shed vortex in a turbine stage

Shear layers shed by aircraft wings roll up into vortices. A similar, though far less common, phenomenon can occur in the wake of a turbomachine blade. This paper presents experimental data from a new single stage turbine that has been commissioned at the Whittle Laboratory. Two low aspect ratio stators have been tested with the same rotor row. Surface flow visualisation illustrates the extremely strong secondary flows present in both NGV designs. These secondary flows lead to conventional passage vortices but also to an intense vortex sheet which is shed from the trailing edge of the blades. Pneumatic probe traverse show how this sheet rolls up into a concentrated vortex in the second stator design, but not in the first. A simple numerical experiment is used to model the shear layer instability and the effects of trailing edge shape and exit yaw angle distribution are investigated. It is found that the latter has a strong influence on shear layer rollup: inhibiting the formation of a vortex downstream of NGV 1 but encouraging it behind NGV 2.

Investigation of extinction in unsteady flames in turbulent combustion by 2D-LIF of OH radials and flamelet analysis

An experimental and theoretical investigation of premixed turbulent combustion in an engine simulator is presented. The distribution of hydroxyl radicals formed in the combustion of propane/air mixtures was visualized by 2D-LIF and used to monitor the progress of the combustion process. For stoichiometric mixtures, images showed a continuous wrinkled flame front, while in lean (λ=1.5) mixtures, local flame extinction was observed as discontinuities in the reaction zone. A bright active reaction zone was still observed in flame inlets and closed concave structures. The effects of self-absorption and of collisional quenching on the fluorescence signal are considered and appear to have only a minor net influence on the shape and width of the flame front. The images are evaluated and interpreted in terms of the Lewis number effect and the laminar flamelet model. Analysis was performed by determining the contour lines of the images (specifically, the ratios of average maximum to equilibrium OH concentration) and comparing with corresponding ratios from unstrained flame simulations. The results show that although the degree of turbulence is not high enough for straining effects to be important, flamelet curvature does play a significant role in the combustion of lean mixtures; this is manifested by a mean effective flame velocity that is less than the laminar burning velocity. © 1991 Combustion Institute.

Health and disease status of Thai pangas, Pangasius hypophthalmus cultured in rural ponds of Mymensingh, Bangladesh

Thai pangas, Pangasius hypophthalmus is one of the important aquaculture species in Bangladesh. Over the last few years spectacular development has been taking place in Thai pangas farming in Mymensingh district. Due to availability of easy breeding and culture techniques as well as quick return, more and more people are converting their rice fields into pangas farms overnight. The present study was carried out to examine health and disease status of Thai pangas mainly through clinical, histopathological and bacteriological techniques. In addition, for collecting primary data on disease and health status of Thai pangas and the resultant socioeconomic impacts on rural households, questionnaire interview and participatory rural appraisal tools were used with selected farming households in three upazilas of Mymensingh district. The most prevalent diseases as reported by the farmers were red spot, followed by anal protrusion, tail and fin rot, pop eye, dropsy and gill rot. Other conditions like cotton wool type lesion, ulceration and white spot were reported but with lower incidence. Four isolates of Aeromonas hydrophila were recovered from kidney and lesion of diseased fish. Hemorrhage over the body especially near mouth and caudal region was noticed in the fishes associated with aeromonad infection. Internally, kidney, liver and spleen became swollen and enlarged. The isolates varied with their pathogenicity. All the four isolates were sensitive to Nitrofurantoin, Cotrimoxazole and Tetracycline but were resistant to Amoxycilline. An attempt was made to treat diseased fish with extracts from neem leaf, garlic and turmeric. Recovery of infection was monitored through mortality and histopathology. General histopathological changes of different organs were also studied. Extract from neem (Azadirachta indica) leaf gave better result. Telangiectasis, lamellar hypertrophy and hyperplasia hemorrhage, lamellar fusion, necrosis of lamellar epithelial cells, presence of parasites and their cysts were the major pathology of gills. Hemorrhagic lesion, pyknotic nuclei and melanomacrophage centers (MMC) were found in the liver of fish. Major pathologies in kidney of fish included presence of MMC, necrotic and ruptured kidney tubules, severe haemopoietic necrosis, and hemorrhage. The economic loss due to disease in Thai pangas farming was estimated from the difference between expected production and actual production. On an average, Thai pangas farmers of Mymensingh incur a loss of Tk. 23,104/ha/cycle due to fish disease (3.6% of expected total production). The loss, however, varied with location and size of farms, type of farmers and management practices. The study also highlighted fish health management related problems and recommended further work for the development of user-friendly farmer-oriented fish health management packages.

Comparison of sensory characteristics and biochemical parameters in commercial frozen prawns

Commercial samples of frozen shrimp of different styles of presentation and size grades were tested for sensory, physical (cooked yield and pH) and biochemical characteristics (moisture, total nitrogen, water extractable nitrogen, nonprotein nitrogen, alpha amino nitrogen, total volatile nitrogen and trimethylamine nitrogen). The test results are compared and correlated. The order of preference of the samples were HL>PUD>P & D. There was significant correlation between sensory score of cooked sample and WEN, NPN and ∞ – NHsub(2)-N values. TVN and TMA-N did not exhibit any correlation with sensory score. It is inferred that in quality measurement of frozen shrimps of commerce the quantity of water soluble components and the total dry matter can be used to support the sensory test results.

Different mechanisms involved in adaptation to stable and unstable dynamics.

Recently, we demonstrated that humans can learn to make accurate movements in an unstable environment by controlling magnitude, shape, and orientation of the endpoint impedance. Although previous studies of human motor learning suggest that the brain acquires an inverse dynamics model of the novel environment, it is not known whether this control mechanism is operative in unstable environments. We compared learning of multijoint arm movements in a "velocity-dependent force field" (VF), which interacted with the arm in a stable manner, and learning in a "divergent force field" (DF), where the interaction was unstable. The characteristics of error evolution were markedly different in the 2 fields. The direction of trajectory error in the DF alternated to the left and right during the early stage of learning; that is, signed error was inconsistent from movement to movement and could not have guided learning of an inverse dynamics model. This contrasted sharply with trajectory error in the VF, which was initially biased and decayed in a manner that was consistent with rapid feedback error learning. EMG recorded before and after learning in the DF and VF are also consistent with different learning and control mechanisms for adapting to stable and unstable dynamics, that is, inverse dynamics model formation and impedance control. We also investigated adaptation to a rotated DF to examine the interplay between inverse dynamics model formation and impedance control. Our results suggest that an inverse dynamics model can function in parallel with an impedance controller to compensate for consistent perturbing force in unstable environments.

Effects of socking [sic] density on ammonia excretion and the growth of Nile tilapia (Oreochromis niloticus L.)

The effects of stocking density (10, 15, 50 & 75 fish in 65L tank) and ammonia excretion on the growth of Nile tilapia, Oreochromis niloticus (12.19 ± 1.21 g) were investigated. Increasing stocking density of Nile tilapia from 15 fish/tank (2.81 g fish/L) to 75 fish/tank (14.07 g fish/L) resulted in associated increase in ammonia level (1.48 ± 0.87 mg/L to 26.44 ± 11.4 mg/L) and significantly lower growth rates. Significantly better feed conversion ratios were found for fish reared at lower (15 fish/tank) stocking densities compared to higher (75 fish/tank) stocking densities. Individual growth rates were significantly better for fish reared at a lower stocking density 15 fish/tank compared to higher stocking density 75 fish/tank and size variation (coefficient of variation in weight) were positively correlated with stocking density. Although water exchange did not have a significant effect on the growth of Nile tilapia for fish stocked at 10 fish/tank (1.88 g fish/L) and 50 fish/tank (9.38 g fish/L), however, the fish in the higher stocking density (9.38 g fish/L) groups and without water exchange, significantly changed the coloration of their bodies (silver to black) which may be due to the lower oxygen levels combined with higher ammonia levels. Ammonia level increased with increasing stocking density and without water exchange. In this study, it may be suggested that when fish reared at higher stocking densities then water exchange must be taken in to consideration so as to help avoid environmental and physiological stress to the fish.

A survey on relation of morphological, molecular and phylogenetic structure of zoanthids of the islands located in the Hormoz Strait (Hormoz, Qeshm, Larak, Hengam)

The order Zoantharia (Zoanthids) is one of the most neglected orders of cnidarians in the Persian Gulf. The present study aims to investigate the biodiversity of this order with morphological and molecular examination in the Persian Gulf. For this purpose, 123 colonies of zoanthids with variety of shape and colors have been collected from intertidal and shallow water zone of four islands, i. e. Hengam, Qeshm, Larak and Hormoz. After sampling, morphological characteristics of each specimen were recorded based on in situ photographs. Then DNA was extracted using the cetyl trimethyl ammonium bromide (CTAB) method. Both mitochondrial 16S ribosomal DNA (mt 16S rDNA) and cytochrome oxidase subunit I (COI) gene fragments were amplified and sequenced. The results of preliminary morphological identification integrated with two mitochondrial markers sequencing demonstrated the presence of five different species in this region; Zoanthus sansibaricus, Palythoa mutuki, Palythoa cf. mutuki, Palythoa tuberculosa and Neozoanthus persicus?. Although at first sight, morphological properties were not successful to delineate zoanthid species, they become reliable criteria to identify and delineate species in field studies after molecular identification.

The effect of spirulina (fresh and dry) on some biological factors in Penaeus semisulcatus larvae

Spirulina is a filamentous cyanobacteria with many applications in food and drug industries, as a food in human, aquaculture, vet and poultry industries… . Semi and mass culture of Spirulina carries out in different countries. This study was carried out in five phases in order to produce this microalga in Iran. The first phase, Spirulina pure stock was imported from Indonesia. After identification of species, it was cultured in laboratory until we took 20 liters of biomass. The semi-mass culture was carried out in green house. Cell concentration and size of Spirulina were recorded during culture daily and their growth rates were calculated. After two weeks, when the size of Spirulina was suitable, biomass of Spirulina was harvested then accumulated Spirulina weighted and dried in 24 hours in laboratory. In order to microbiological study, the samples of Spirulina (dry and fresh) were cultured on blood agar medium and coliforms were counted. The chemical composition of produced Spirulina was measured by standard methods. Fatty acid and amino acid profiles were acquired by GC and HPLC instruments, respectively. The amount of chlorophyll in Spirulina was determined by spectroscopy method. Also astaxanthin pigment as an important carotenoid was measured by HPLC in Spirulina and Penaeus semisulcatus larvae fed on Spirulina. At final phase of this project, larva fed on produced Spirulina (biomass and dry powder) was compared to Z plus, microencapsulated Spirulina (M.C.F) and Chaetoceros algae as control. This experiment was carried from zoa to early post larvae stage then survival and growth rate of larvae were recorded. The growth rate of larvae was evaluated with ANOVA test and survival rate of treatments was assessed by Log Rank (Mantel –Cox) test. Also during larvae stage, two parameters of water such as nitrate and nitrite were measured in zoa, mysis and post larvae stages. The results of this study were shown that colifom counts were 1.85×106 and 92.3×105 coliform per ml in fresh and dry spirulina, respectively. Protein percent of dry spirulina was 50.93 % (dry weight) and the amount of astaxanthin in spirulina and larvae fed on spirulina were 0.21 and 0.01 mg/kg, respectively. The most survival rate of larvae were observed in zoa III (88.8%) with Z plus supplement treatment, in mysis III (76.5%) combination of Z plus and dry spirulina in comparative between treatments. Larvae growth (4.5mm) of control in early post larvae was the best.

Genetic status of selected fish taxa in relation to conservation of genetic and species diversity in the Victoria and Kyoga Lake basins

Cichlids are known for their explosive radiation especially in the African Great Lakes marked with a high level of lake endemism. These fishes have been characterized mainly along trophic and habitat differences, by variation in morphological structures such as teeth and jaws and by differences in body shape and coloration. Cichlids are important as a microcosm of macroevolution. The explosive radiation, young evolutionary scale, and the isolation of groups characterized with high levels of endemism and presence of living fossils makes the group important for evolutionary and genetic studies. Lake Victoria region cichlids which are isolated and relatively more recent in evolution were the last to be appreciated in their diversity. Recently Ole Seehausen has found scores of rock fishes in Lake Victoria which were up to then thought to be absent from the Lake and only known to occur in Lakes Malawi and Tanganyika. Greenwood put together the species groups of Lake Victoria, and later in the early 1980's revised the classification of haplochromine species to reflect the phyletic origin and interrelationship of the various groups in Lake Victoria region. Melan Stiassny has been interested in early evolution of cichlids while the likes of Paul Fuerst and Lees Kaufman and Axel Meyer have been interested and are working to explain the speciation mechanisms responsible for the explosive radiation and evolution of cichlids. Locally S.B Wandera and his student Getrude Narnulemo are spearheading the biodiversity and taxonomic studies of cichlids in Lake Victoria region

Biology, ecology and the fishery of Mukene, Rastrineobola argentea

Food and feeding, condition factor, breeding periods, growth and size at first maturity of a small pelagic cyprinid Rastrineobola argentea (P.) in Lake Victoria are determined. Fishing gears and methods that have been used in the exploitation of the species and could be harmful to the fishery are outlined. Management measures leading to possible sustainable exploitation of the fishery are suggested. Adult R. argentea feed on zooplankton during daytime. Juveniles feed on planktonic early instars of lakefly larvae. Although the species breeds throughout the year, two breeding peaks were observed during the drier months of August and December January. Least breeding was observed in the rainy months of April-May and October November. Fishes from the open water station at Bugaia showed higher numbers of breeding individuals than those from inshore areas. The mean monthly condition factor of fish from Napoleon Gulf confirmed breeding peaks as obtained from the number of fish with ripe gonads. The species showed a mean instantaneous growth rate (K) of 1.75 and attains length infinity (Lx) of 54mm. Females of the species in these waters show a reduced size at maturity as compared to ten years ago when exploitation of the species was at minimal levels. The males have however not changed much.

Retail prices of split, smoked, dried bream and dried Lake Tanganyika sardines at Lusaka markets, 1968-1970

This paper reports the results of a retail price survey at Lusaka markets on split, smoked, dried bream (Tilapia spp.) in 1968-69 and dried Lake Tanganyika sardines (Limnothrissa miodon and Stolothrissa tanangicae) in 1969-70. During the survey periods the average prices of these products maintained a level 70% to 130% higher than those fixed by the Government. Price fluctuations in relation to season, size and quality of the products were discussed. The prices were affected by season and size of the products but not by quality in terms of appearance and smell of the non-cooked products.

Silhouette-based object phenotype recognition using 3D shape priors

This paper tackles the novel challenging problem of 3D object phenotype recognition from a single 2D silhouette. To bridge the large pose (articulation or deformation) and camera viewpoint changes between the gallery images and query image, we propose a novel probabilistic inference algorithm based on 3D shape priors. Our approach combines both generative and discriminative learning. We use latent probabilistic generative models to capture 3D shape and pose variations from a set of 3D mesh models. Based on these 3D shape priors, we generate a large number of projections for different phenotype classes, poses, and camera viewpoints, and implement Random Forests to efficiently solve the shape and pose inference problems. By model selection in terms of the silhouette coherency between the query and the projections of 3D shapes synthesized using the galleries, we achieve the phenotype recognition result as well as a fast approximate 3D reconstruction of the query. To verify the efficacy of the proposed approach, we present new datasets which contain over 500 images of various human and shark phenotypes and motions. The experimental results clearly show the benefits of using the 3D priors in the proposed method over previous 2D-based methods. © 2011 IEEE.

Effect of buried depth and diameter on uplift of underground structures in liquefied soils

In an earthquake, underground structures located in liquefiable soil deposits are susceptible to floatation following an earthquake event due to their lower unit weight relative to the surrounding saturated soil. The uplift displacement of an underground structure in liquefiable soil deposit can be affected by the buried depth and size of the structure. Dynamic centrifuge tests have been carried out to investigate the influence of these factors by measuring the uplift displacement of shallow model circular structures. Ratios for the buried depth and diameter effects of the structure are introduced to compare the uplift displacement in different soil and earthquake conditions. With the depth effect and diameter effect ratios, the uplift displacement of a buoyant structure in liquefiable soil can also be estimated based on performance of similar structures in comparable soil condition and subjected to a similar earthquake event. © 2012 Elsevier Ltd.

Enhancement of Construction Equipment Detection in Video Frames by Combining with Tracking

Vision-based object detection has been introduced in construction for recognizing and locating construction entities in on-site camera views. It can provide spatial locations of a large number of entities, which is beneficial in large-scale, congested construction sites. However, even a few false detections prevent its practical applications. In resolving this issue, this paper presents a novel hybrid method for locating construction equipment that fuses the function of detection and tracking algorithms. This method detects construction equipment in the video view by taking advantage of entities' motion, shape, and color distribution. Background subtraction, Haar-like features, and eigen-images are used for motion, shape, and color information, respectively. A tracking algorithm steps in the process to make up for the false detections. False detections are identified by catching drastic changes in object size and appearance. The identified false detections are replaced with tracking results. Preliminary experiments show that the combination with tracking has the potential to enhance the detection performance.

Insight into differences in nanoindentation properties of bone.

Nanoindentation provides the ideal framework to determine mechanical properties of bone at the tissue scale without being affected by the size, shape, and porosity of the bone. However, the values of tissue level mechanical properties vary significantly between studies. Since the differences in the bone sample, hydration state, and test parameters complicate direct comparisons across the various studies, these discrepancies in values cannot be compared directly. The objective of the current study is to evaluate and compare mechanical properties of the same bones using a broad range of testing parameters. Wild type C56BL6 mice tibiae were embedded following different processes and tested in dry and rehydrated conditions. Spherical and Berkovich indenter probes were used, and data analysis was considered within the elasto-plastic (Oliver-Pharr), viscoelastic and visco-elastic-plastic frameworks. The mean values of plane strain modulus varied significantly depending on the hydration state, probe geometry and analysis method. Indentations in dry bone analyzed using a visco-elastic-plastic approach gave values of 34 GPa. After rehydrating the same bones and indenting them with a spherical tip and utilizing a viscoelastic analysis, the mean modulus value was 4 GPa, nearly an order of magnitude smaller. Results suggest that the hydration state, probe geometry and the limitations and assumptions of each analysis method influence significantly the measured mechanical properties. This is the first time that such a systematic study has been carried out and it has been concluded that the discrepancies in the mechanical properties of bone measured by nanoindentation found in the literature should not be attributed only to the differences between the bones themselves, but also to the testing and analysis protocols.