Construção, caracterização e aplicação de eletrodos para descarga por arco de cátodo oco

The system built to characterize electrodes and, consequently, deposited fine films are constituted by a hollow cathode that works to discharges and low pressures (approximately 10-3 to 5 mbar), a source DC (0 to 1200 V), a cylindrical camera of closed borossilicato for flanges of stainless steel with an association of vacuum bombs mechanical and spread. In the upper flange it is connected the system of hollow cathode, which possesses an entrance of gas and two entrances for its refrigeration, the same is electrically isolated of the rest of the equipment and it is polarized negatively. In front of the system of hollow cathode there is a movable sample in stainless steel with possibility of moving in the horizontal and vertical. In the vertical, the sample can vary its distance between 0 and 70 mm and, in the horizontal, can leave completely from the front of the hollow cathode. The sample and also the cathode hollow are equipped with cromel-alumel termopares with simultaneous reading of the temperatures during the time of treatment. In this work copper electrodes, bronze, titanium, iron, stainless steel, powder of titanium, powder of titanium and silício, glass and ceramic were used. The electrodes were investigated relating their geometry change and behavior of the plasma of the cavity of hollow cathode and channel of the gas. As the cavity of hollow cathode, the analyzed aspects were the diameter and depth. With the channel of the gas, we verified the diameter. In the two situations, we investigated parameters as flow of the gas, pressure, current and applied tension in the electrode, temperature, loss of mass of the electrode with relationship at the time of use. The flow of gas investigated in the electrodes it was fastened in a work strip from 15 to 6 sccm, the constant pressure of work was among 2.7 to 8 x 10-2 mbar. The applied current was among a strip of work from 0,8 to 0,4 A, and their respective tensions were in a strip from 400 to 220 V. Fixing the value of the current, it was possible to lift the curve of the behavior of the tension with the time of use. That curves esteem in that time of use of the electrode to its efficiency is maximum. The temperatures of the electrodes were in the dependence of that curves showing a maximum temperature when the tension was maximum, yet the measured temperatures in the samples showed to be sensitive the variation of the temperature in the electrodes. An accompaniment of the loss of mass of the electrode relating to its time of use showed that the electrodes that appeared the spherical cavities lost more mass in comparison with the electrodes in that didn't appear. That phenomenon is only seen for pressures of 10-2 mbar, in these conditions a plasma column is formed inside of the channel of the gas and in certain points it is concentrated in form of spheres. Those spherical cavities develop inside of the channel of the gas spreading during the whole extension of the channel of the gas. The used electrodes were cut after they could not be more used, however among those electrodes, films that were deposited in alternate times and the electrodes that were used to deposit films in same times, those films were deposited in the glass substrata, alumina, stainless steel 420, stainless steel 316, silício and steel M2. As the eletros used to deposit films in alternate time as the ones that they were used to deposit in same times, the behavior of the thickness of the film obeyed the curve of the tension with relationship the time of use of the electrode, that is, when the tension was maximum, the thickness of the film was also maximum and when the tension was minimum, the thickness was minimum and in the case where the value of the tension was constant, the thickness of the film tends to be constant. The fine films that were produced they had applications with nano stick, bio-compatibility, cellular growth, inhibition of bacterias, cut tool, metallic leagues, brasagem, pineapple fiber and ornamental. In those films it was investigated the thickness, the adherence and the uniformity characterized by sweeping electronic microscopy. Another technique developed to assist the production and characterization of the films produced in that work was the caloteste. It uses a sphere and abrasive to mark the sample with a cap impression, with that cap form it is possible to calculate the thickness of the film. Through the time of life of the cathode, it was possible to evaluate the rate of waste of its material for the different work conditions. Values of waste rate up to 3,2 x 10-6 g/s were verified. For a distance of the substratum of 11 mm, the deposited film was limited to a circular area of 22 mm diameter mm for high pressures and a circular area of 75 mm for pressure strip. The obtained films presented thickness around 2,1 µm, showing that the discharge of arch of hollow cathode in argon obeys a curve characteristic of the tension with the time of life of the eletrodo. The deposition rate obtained in this system it is of approximately 0,18 µm/min

Design Aspects of a Broadband Beam-Reconfigurable Leaky-Wave Antenna

Design aspects of a novel beam-reconfigurable pla-nar series-fed array are addressed to achieve beam steering with frequency tunability over a relatively broad bandwidth. The design is possible thanks to the use of the complementary strip-slot, which is an innovative broadly matched microstrip radiator, and the careful selection of the phase shifter parameters.

Problemas de corte : métodos exactos y aproximados para formulaciones mono y multi-objetivo

Los problemas de corte y empaquetado son una familia de problemas de optimización combinatoria que han sido ampliamente estudiados en numerosas áreas de la industria y la investigación, debido a su relevancia en una enorme variedad de aplicaciones reales. Son problemas que surgen en muchas industrias de producción donde se debe realizar la subdivisión de un material o espacio disponible en partes más pequeñas. Existe una gran variedad de métodos para resolver este tipo de problemas de optimización. A la hora de proponer un método de resolución para un problema de optimización, es recomendable tener en cuenta el enfoque y las necesidades que se tienen en relación al problema y su solución. Las aproximaciones exactas encuentran la solución óptima, pero sólo es viable aplicarlas a instancias del problema muy pequeñas. Las heurísticas manejan conocimiento específico del problema para obtener soluciones de alta calidad sin necesitar un excesivo esfuerzo computacional. Por otra parte, las metaheurísticas van un paso más allá, ya que son capaces de resolver una clase muy general de problemas computacionales. Finalmente, las hiperheurísticas tratan de automatizar, normalmente incorporando técnicas de aprendizaje, el proceso de selección, combinación, generación o adaptación de heurísticas más simples para resolver eficientemente problemas de optimización. Para obtener lo mejor de estos métodos se requiere conocer, además del tipo de optimización (mono o multi-objetivo) y el tamaño del problema, los medios computacionales de los que se dispone, puesto que el uso de máquinas e implementaciones paralelas puede reducir considerablemente los tiempos para obtener una solución. En las aplicaciones reales de los problemas de corte y empaquetado en la industria, la diferencia entre usar una solución obtenida rápidamente y usar propuestas más sofisticadas para encontrar la solución óptima puede determinar la supervivencia de la empresa. Sin embargo, el desarrollo de propuestas más sofisticadas y efectivas normalmente involucra un gran esfuerzo computacional, que en las aplicaciones reales puede provocar una reducción de la velocidad del proceso de producción. Por lo tanto, el diseño de propuestas efectivas y, al mismo tiempo, eficientes es fundamental. Por esta razón, el principal objetivo de este trabajo consiste en el diseño e implementación de métodos efectivos y eficientes para resolver distintos problemas de corte y empaquetado. Además, si estos métodos se definen como esquemas lo más generales posible, se podrán aplicar a diferentes problemas de corte y empaquetado sin realizar demasiados cambios para adaptarlos a cada uno. Así, teniendo en cuenta el amplio rango de metodologías de resolución de problemas de optimización y las técnicas disponibles para incrementar su eficiencia, se han diseñado e implementado diversos métodos para resolver varios problemas de corte y empaquetado, tratando de mejorar las propuestas existentes en la literatura. Los problemas que se han abordado han sido: el Two-Dimensional Cutting Stock Problem, el Two-Dimensional Strip Packing Problem, y el Container Loading Problem. Para cada uno de estos problemas se ha realizado una amplia y minuciosa revisión bibliográfica, y se ha obtenido la solución de las distintas variantes escogidas aplicando diferentes métodos de resolución: métodos exactos mono-objetivo y paralelizaciones de los mismos, y métodos aproximados multi-objetivo y paralelizaciones de los mismos. Los métodos exactos mono-objetivo aplicados se han basado en técnicas de búsqueda en árbol. Por otra parte, como métodos aproximados multi-objetivo se han seleccionado unas metaheurísticas multi-objetivo, los MOEAs. Además, para la representación de los individuos utilizados por estos métodos se han empleado codificaciones directas mediante una notación postfija, y codificaciones que usan heurísticas de colocación e hiperheurísticas. Algunas de estas metodologías se han mejorado utilizando esquemas paralelos haciendo uso de las herramientas de programación OpenMP y MPI.

Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Effect of clearing native forest (Caatinga) strips on some hydrologic components of micro-watersheds.

The influences of clearing native vegetation (Caatinga) in contour strips at 25 cm vertical interval on evaporation losses in cleared strips, annual runoff efficiency and annuall soil loss on gently sloped micro-waterheds in the arid zones of Northeast Brazil are reported. The alternate native vegetation (Caatinga) strips function very effectively as windbreaks thus reducing evaporation losses substantially in the leeward cleared strips. The runoff measured at the micro-watershed with cleared strips was many-fold lower than the runoff obtained at a completely denuded watershed even when it was protected by narrow based channel terraces. However, the annual runoff efficiency can be significantly increased in a strip cleared watershed if narrow based channel terraces are provided on the lower side of cleared strips. The annual soil losses in strip cleared watersheds as well as completely denuded waterhed of gentle slopes were negligible. Thus clearing land in alternate contour strips on a micro-watersheds shall substantially improve crop water use efficiency without creating any significant erosion problems. Additionally this treatment will increase runoff for water harvesting for irrigation purposes.

Natal qual é a sua cara?: análise do perfil edilício da avenida Eng. Roberto Freire (Natal/RN) à luz da acessibilidade

This study focuses on the building ensemble of Avenida Roberto Freire, a main road in Natal, Brazil, as a material expression of the confluence of various factors among which the following may be emphasized: high level of accessibility due to urban spatial re-structuring and the growth of the real estate market, in view of the increasing number of consumers, who arrived in Natal within the last decades. The intense urban modification process that has been going on in Natal since at least the 1980s, has engendered the formation of long axial lines which express the expansion dynamics and some of the forces subjacent to it. Avenida Roberto Freire has been an iconic example of an urban thoroughfare where architecture becomes primarily a communication support that can be perceived by fast moving passers-by, what brings it close to the venturian concept of strip (Venturi at al, 1972). The building types that line the road not only respond to the dynamics in process but also contribute to intensify it, as they house a variety of uses which attract people and generate more movement. The dynamics is further strengthened by the action of the real estate business which benefits from the increase of highly accessible locations, and from the private and public investments and incentives to tourism that aim to insert this city into the globalized world. Although the intention of reconstituting part of the history of density increase on this avenue in a diachronical perspective was attempted within the limits of the available references and documentation, the central contribution of this study is to understand the relations between topological accessibility and the typological nature of the building ensemble. By observing the synchronic morphological frame resulting from the spatial configuration analysis pertinent to this avenue (cf. Hillier and Hanson,1984) and the inventory and classification of the building ensemble there existing, this study aims to understand how architecture responds to accessibility in view of the real estate pressure, boosted by a cosmopolitanizing process brought about by the continuous flow of foreign and Brazilian arrivals as visitors, temporary or permanent residents

Exact solutions for the agricultural and the two-dimensional packing problems

Objectives and study method: The objective of this study is to develop exact algorithms that can be used as management tools for the agricultural production planning and to obtain exact solutions for two of the most well known twodimensional packing problems: the strip packing problem and the bin packing problem. For the agricultural production planning problem we propose a new hierarchical scheme of three stages to improve the current agricultural practices. The objective of the first stage is to delineate rectangular and homogeneous management zones into the farmer’s plots considering the physical and chemical soil properties. This is an important task because the soil properties directly affect the agricultural production planning. The methodology for this stage is based on a new method called “Positions and Covering” that first generates all the possible positions in which the plot can be delineated. Then, we use a mathematical model of linear programming to obtain the optimal physical and chemical management zone delineation of the plot. In the second stage the objective is to determine the optimal crop pattern that maximizes the farmer’s profit taken into account the previous management zones delineation. In this case, the crop pattern is affected by both management zones delineation, physical and chemical. A mixed integer linear programming is used to solve this stage. The objective of the last stage is to determine in real-time the amount of water to irrigate in each crop. This stage takes as input the solution of the crop planning stage, the atmospheric conditions (temperature, radiation, etc.), the humidity level in plots, and the physical management zones of plots, just to name a few. This procedure is made in real-time during each irrigation period. A linear programming is used to solve this problem. A breakthrough happen when we realize that we could propose some adaptations of the P&C methodology to obtain optimal solutions for the two-dimensional packing problem and the strip packing. We empirically show that our methodologies are efficient on instances based on real data for both problems: agricultural and two-dimensional packing problems. Contributions and conclusions: The exact algorithms showed in this study can be used in the making-decision support for agricultural planning and twodimensional packing problems. For the agricultural planning problem, we show that the implementation of the new hierarchical approach can improve the farmer profit between 5.27% until 8.21% through the optimization of the natural resources. An important characteristic of this problem is that the soil properties (physical and chemical) and the real-time factors (climate, humidity level, evapotranspiration, etc.) are incorporated. With respect to the two-dimensional packing problems, one of the main contributions of this study is the fact that we have demonstrate that many of the best solutions founded in literature by others approaches (heuristics approaches) are the optimal solutions. This is very important because some of these solutions were up to now not guarantee to be the optimal solutions.

DESIGN AND APPLICATION OF WIRELESS PASSIVE MAGNETOELASTIC RESONANCE AND MAGNETOHARMONIC FORCE SENSORS

The objective of the work described in this dissertation is the development of new wireless passive force monitoring platforms for applications in the medical field, specifically monitoring lower limb prosthetics. The developed sensors consist of stress sensitive, magnetically soft amorphous metallic glass materials. The first technology is based on magnetoelastic resonance. Specifically, when exposed to an AC excitation field along with a constant DC bias field, the magnetoelastic material mechanically vibrates, and may reaches resonance if the field frequency matches the mechanical resonant frequency of the material. The presented work illustrates that an applied loading pins portions of the strip, effectively decreasing the strip length, which results in an increase in the frequency of the resonance. The developed technology is deployed in a prototype lower limb prosthetic sleeve for monitoring forces experienced by the distal end of the residuum. This work also reports on the development of a magnetoharmonic force sensor comprised of the same material. According to the Villari effect, an applied loading to the material results in a change in the permeability of the magnetic sensor which is visualized as an increase in the higher-order harmonic fields of the material. Specifically, by applying a constant low frequency AC field and sweeping the applied DC biasing field, the higher-order harmonic components of the magnetic response can be visualized. This sensor technology was also instrumented onto a lower limb prosthetic for proof of deployment; however, the magnetoharmonic sensor illustrated complications with sensor positioning and a necessity to tailor the interface mechanics between the sensing material and the surface being monitored. The novelty of these two technologies is in their wireless passive nature which allows for long term monitoring over the life time of a given device. Additionally, the developed technologies are low cost. Recommendations for future works include improving the system for real-time monitoring, useful for data collection outside of a clinical setting.