Preparation of composite electrodes with carbon nanotubes for lithium-ion batteries by low-energy ball milling

Some of the prospective electrode materials for lithium-ion batteries are known to have electronic transport limitations preventing them from being used in the electrodes directly. In many cases, however, these materials may become practical if they are applied in the form of nanocomposites with a carbon component, e.g. via incorporating nanoparticles of the phase of interest into a conducting network of carbon nanotubes. A simple way to prepare oxide-carbon nanotube composites suitable for the electrodes of lithium-ion batteries is presented in this paper. The method is based on low-energy ball milling. An electrochemically active but insulating phase of LiFeTiO4 is used as a test material. It is demonstrated that the LiFeTiO4-carbon nanotube composite is not only capable of having significantly higher capacity (∼105-120 mA h g-1vs. the capacity of ∼65-70 mA h g -1 for the LiFeTiO4 nanoparticles) at a slow current rate but may also operate at reasonably high current rates. © the Partner Organisations 2014.

Hybrid high internal phase emulsion (HIPE) organogels with oil separation properties

Hybrid HIPE organogels were prepared from pre-formed hybrid organogels, which were formed from a triblock ionomer and Fe3O4 nanoparticles via charge-driven assembly. Magnetic materials can be obtained from these hybrid HIPE organogels simply by removal of solvents, and these materials have been confirmed to be excellent candidates for absorption of oil from water.

Self-assembled multimicellar vesicles via complexation of a rigid conjugated polymer with an amphiphilic block copolymer

A viable method of encapsulating block copolymer micelles inside vesicles using a conjugated polymer is reported in this study. Self-assembly and complexation between an amphiphilic block copolymer poly(methyl methacrylate)-b-poly(acrylic acid) (PMMA-b-PAA) and a rod-like conjugated polymer polyaniline (PANI) in aqueous solution were studied using transmission electron microscopy, atomic force microscopy and dynamic light scattering. The complexation and morphology transformation were driven by electrostatic interaction between PANI and the PAA block of the block copolymer. Addition of PANI to PMMA-b-PAA induced the morphology transformation from micelles to irregular vesicles through vesicles, thick-walled vesicles (TWVs) and multimicellar vesicles (MMVs). Among the observed morphologies, MMVs were observed for the first time. Morphology transformation was studied as a function of aniline/acrylic acid molar ratio ([ANI]/[AA]). Micelles were observed for the pure block copolymer, while vesicles and TWVs were observed at [ANI]/[AA] = 0.1 and 0.3, respectively. MMVs were observed at [ANI]/[AA] = 0.5 and irregular vesicles were observed for molar ratios at 0.7 and above. Clearly, a conjugated polymer like polyaniline can induce a morphology transformation even at its lower concentrations and produce complex morphologies.

Stable superhydrophobic surface based on silicone combustion product

Discarded silicone products can be recycled to prepare superhydrophobic powder by simply burning and smashing. The powder can be used to fabricate a superhydrophobic surface with mechanical durability such that the superhydrophobicity was kept after 50 abrasion cycles. A robust electroconductive superhydrophobic surface can also be obtained by this simple method.

Lithium ferrite (Li0.5Fe2.5O4) nanoparticles as anodes for lithium ion batteries

Li0.5Fe2.5O4 nanoparticles of about 80 nm were synthesized through a hydrothermal method, followed by a solid state reaction between LiOH·H2O and Fe2O3. The Li0.5Fe2.5O4 nanoparticles exhibit a remarkable high capacity (up to 1124 mA h g-1), a good cycle stability (650 mA h g-1 after 50 cycles) and excellent coulombic efficiency. © 2014 the Partner Organisations.

Identify kinetic features of fibers growing, branching, and bundling in microstructure engineering of crystalline fiber network

Fibers growing, branching, and bundling are essential for the development of crystalline fiber networks of molecular gels. In this work, for two typical crystalline fiber networks, i.e. the network of spherulitic domains and the interconnected fibers network, related kinetic information is obtained using dynamic rheological measurements and analysis in terms of the Avrami theory. In combination with microstructure characterizations, we establish the correlation of the Avrami derived kinetic parameter not only with the nucleation nature and growth dimensionality of fibers and branches, but also with the fiber bundles induced by fiber-fiber interactions. Our study highlights the advantage of simple dynamic rheological measurements over other spectroscopic methods used in previous studies for providing more kinetic information on fiber-fiber interactions, enabling the Avrami analyses to extract distinct kinetic features not only for fibers growing and branching, but also for bundling in the creation of strong interconnected fibers networks. This work may be helpful for the implementation of precise kinetic control of crystalline fiber network formations for achieving desirable microstructures and rheological properties for advanced applications of gel materials. This journal is © the Partner Organisations 2014.

Spectroscopic and computational characterizations of alkaline-earth- and heavy-metal-exchanged natrolites

Synchrotron infrared (IR) and micro-Raman spectra of natrolites containing alkaline-earth ions (Ca2+, Sr2+, and Ba2+) and heavy metals (Cd2+, Pb2+, and Ag+) as extra-framework cations (EFCs) were measured under ambient conditions. Complementing our previous spectroscopic investigations of natrolites with monovalent alkali metal (Li+, Na+, K+, Rb +, and Cs+) EFCs, we establish a correlation between the redshifts of the frequencies of the 4-ring and helical 8-ring units and the size of the EFCs in natrolite. Through ab initio calculations we have derived structural models of Ca2+- and Ag+-exchanged natrolites with hydrogen atoms, and found that the frequency shifts in the H - O - H bending mode and the differences in the O - H stretching vibration modes can be correlated with the orientations of the water molecules along the natrolite channel. Assuming that the members of a solid solution series behave as an ideal mixture, we will be able to use spectroscopy to probe compositions. Deviation from ideal behavior might indicate the occurrence of phase separation on various length scales. Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Large compound vesicles from amphiphilic block copolymer/rigid-rod conjugated polymer complexes

Morphology evolution in complexes of amphiphilic block copolymers poly(styrene)-b-poly(acrylic acid) (PS-b-PAA) and poly(styrene)-b-poly(ethylene oxide) (PS-b-PEO) in the presence of polyaniline (PANI) in aqueous solution is reported. Transmission electron microscopy, atomic force microscopy, and dynamic light scattering techniques were used to study the morphologies at various PANI contents [aniline]/[acrylic acid] ([ANI]/[AA]) ranging from 0.1 to 0.7. The interpolyelectrolyte complex formed between PAA and PANI plays a key role in the morphology transformation. Spherical micelles formed from pure block copolymers were transformed into large compound vesicles upon increasing PANI concentration due to internal block copolymer segregation. In addition to varying PANI content, the kinetic pathway of nanoparticle formation was controlled through different water addition methods and was critical in the formation of multigeometry nanoparticles.

Continuous polyacrylonitrile nanofiber yarns: Preparation and dry-drawing treatment for carbon nanofiber production

Precursor fibers with diameters in nanometer scale and highly aligned polymer chains in fibers are highly promising for the preparation of high-performance carbon nanofibers, but are challenging to make. In this study, we demonstrate for the first time that a carbon nanofiber precursor can be prepared by the electrospinning of polyacrylonitrile into a nanofiber yarn and by the subsequent drawing treatment of the yarn in dry conditions. The yarn shows excellent drawing performance, which can be drawn evenly up to 6 times of its original length without breaking. The drawing treatment improves the yarn and fiber uniformity, polymer chain orientation within the fibers, as well as yarn tension and modules, but shows decreased yarn and fiber diameter and elongation at break. The drawing temperature and force show influences on the drawing behavior. The highest strength and modules (362 ± 37 MPa and 9.2 ± 1.4 GPa, respectively) are found on the yarn drawn by 5 times its length, which increased by 800% and 1800% when compared to the as-spun yarn. Through un-optimized stabilization and carbonization treatments, we further demonstrate that the carbonized nanofiber yarn shows comparable tensile properties as the commercial carbon fibers. Electrospun nanofiber yarns may form next generation precursors for making high performance carbon fibers. This journal is

A superamphiphobic coating with an ammonia-triggered transition to superhydrophilic and superoleophobic for oil-water separation

Superhydrophilic and superoleophobic materials are very attractive for efficient and cost-effective oil-water separation, but also very challenging to prepare. Reported herein is a new superamphiphobic coating that turns superhydrophilic and superoleophobic upon ammonia exposure. The coating is prepared from a mixture of silica nanoparticles and heptadecafluorononanoic acid-modified TiO2 sol by a facile dip-coating method. Commonly used materials, including polyester fabric and polyurethane sponge, modified with this coating show unusual capabilities for controllable filtration of an oil-water mixture and selective removal of water from bulk oil. We anticipate that this novel coating may lead to the development of advanced oil-water separation techniques.

The Influence of water and metal salt on the transport and structural properties of 1-Octyl-3-methylimidazolium Chloride

The addition of diluents to ionic liquids (ILs) has recently been shown to enhance the transport properties of ILs. In the context of electrolyte design, this enhancement allows the realisation of IL-based electrolytes for metal-air batteries and other storage devices. It is likely that diluent addition not only impacts the viscosity of the IL, but also the ion-ion interactions and structure. Here, we investigate the nano-structured 1-methyl-3-octylimidazolium chloride (OMImCl) with varying water concentrations in the presence of two metal salts, zinc chloride and magnesium chloride. We find that the choice of metal salt has a significant impact on the structure and transport properties of the system; this is explained by the water structuring and destructing properties of the metal salt.

Tristearin bilayers: structure of the aqueous interface and stability in the presence of surfactants

We report results of atomistic molecular dynamics simulations of an industrially-relevant, exemplar triacylglycerol (TAG), namely tristearin (TS), under aqueous conditions, at different temperatures and in the presence of an anionic surfactant, sodium dodecylbenzene sulphonate (SDBS). We predict the TS bilayers to be stable and in a gel phase at temperatures of 350 K and below. At 370 K the lipid bilayer was able to melt, but does not feature a stable liquid-crystalline phase bilayer at this elevated temperature. We also predict the structural characteristics of TS bilayers in the presence of SDBS molecules under aqueous conditions, where surfactant molecules are found to spontaneously insert into the TS bilayers. We model TS bilayers containing different amounts of SDBS, with the presence of SDBS imparting only a moderate effect on the structure of the system. Our study represents the first step in applying atomistic molecular dynamics simulations to the investigation of TAG-aqueous interfaces. Our results suggest that the CHARMM36 force-field appears suitable for the simulation of such systems, although the phase behaviour of the system may be shifted to lower temperatures than is the case for the actual system. Our findings provide a foundation for further simulation studies of the TS-aqueous interface.

Different thermal analysis technique application in determination of fold surface-free energy

In this work, the crystallization rates and spherulitic growth rate of miscible blends of poly(vinylidene fluoride) (PVDF) and acrylic rubber (ACM) were determined using differential scanning calorimetry (DSC), real-time FTIR, and optical microscopy. FTIR results suggest that blending does not induce the creation of polymorphic crystalline forms of PVDF. SAXS data demonstrate the formation of interlamellar structure after blending. The fold surface-free energy (σ e) was analyzed and compared using different thermal analysis techniques. The isothermal crystallization curves obtained using real-time FTIR and DSC explored in two different methods: t 1/2 or Avrami equation. While the Avrami equation is more widespread and precise, both analytical methods gave similar free energy of folding values. However, it was found that the direct optical method of measuring spherulitic growth rate yields σ e values 30-50 % lower than those obtained from the overall crystallization rate data. Conversely, the σ e values were found to increase with increasing amorphous ACM phase content regardless of the analytical methods.

Protocols for finding the most orthogonal dimensions for two-dimensional high performance liquid chromatography

The selection of two high performance liquid chromatography (HPLC) columns with vastly different retention mechanisms is vital for performing effective two-dimensional (2D-) HPLC. This paper reports on a systematic method to select a pair of HPLC columns that provide the most different separations for a given sample. This was completed with the aid of a HPLC simulator that predicted retention profiles on the basis of real experimental data, which is difficult when the contents of sample matrices are largely-or completely-unknown. Peaks from the same compounds must first be matched between chromatograms to compare the retention profiles and optimised 2D-HPLC column selection. In this work, two methods of matching peaks between chromatograms were explored and an optimal pair of chromatography columns was selected for 2D-HPLC. First, a series of 17 antioxidants were selected as an analogue for a coffee extract. The predicted orthogonality of the standards was 39%, according to the fractional surface coverage 'bins' method, which was close to the actual space utilisation of the standard mixture, 44%. Moreover, the orthogonality for the 2D-HPLC of coffee matched the predicted value of 38%. The second method employed a complex sample matrix of urine to optimise the column selections. Seven peaks were confidently matched between chromatograms by comparing relative peak areas of two detection strategies: UV absorbance and potassium permanganate chemiluminescence. It was found that the optimal combinations had an orthogonality of 35% while the actual value was closer to 30%.