The fractionation of dextran polymer by ultrafiltration to yield clinical products

A review of ultrafiltration (UF) theory and equipment has been made. Dextran is fractionated industrially by ethanol precipitation, which is a high energy intensive process. The aims of this work were to investigate the fractionation of dextran using UF and to compare the efficiency and costs of UF fractionation with ethanol fractionation. This work is the continuation of research conducted at Aston, which was concerned with the fractionation of dextran using gel permeation chromatography (GPC) and hollow fibre UF membranes supplied by Amicon Ltd. Initial laboratory work centred on determining the most efficient make and configuration of membrane. UF membranes of the Millipore cassette configuration, and the DDS flat-sheet configuration, were examined for the fracationation of low molecular weight (MW) dextran. When compared to Amicon membranes, these membranes were found to be inferior. DDS membranes of 25 000 and 50 000 MW cut-offs were shown to be capable of fractionating high MW dextran with the same efficiency as GPC. The Amicon membranes had an efficiency comparable to that of ethanol fractionation. To increase this efficiency a theoretical UF membrane cascade was adopted to utilize favourable characteristics encountered in batch mode membrane experiments. The four stage cascade used recycled permeates in a counter- current direction to retentate flow, and was operated 24 hours per day controlled by a computer. Using 5 000 MW cut-off membranes the cascade improved the batch efficiency by at least 10% for a fractionation at 6 000 MW. Economic comparisons of ethanol fractionation, combined GPC and UF fractionation, and UF fractionation of dextran were undertaken. On an economic basis GPC was the best method for high MW dextran fractionation. When compared with a plant producing 100 tonnes pa of clinical dextran, by ethanol fractionation, a combined GPC and UF cascade fractionation could produce savings on operating costs and an increased dextran yield of 5%.

Factors affecting human reliability in the chemical process industry

This research was concerned with identifying factors which may influence human reliability within chemical process plants - these factors are referred to as Performance Shaping Factors (PSFs). Following a period of familiarization within the industry, a number of case studies were undertaken covering a range of basic influencing factors. Plant records and site `lost time incident reports' were also used as supporting evidence for identifying and classifying PSFs. In parallel to the investigative research, the available literature appertaining to human reliability assessment and PSFs was considered in relation to the chemical process plan environment. As a direct result of this work, a PSF classification structure has been produced with an accompanying detailed listing. Phase two of the research considered the identification of important individual PSFs for specific situations. Based on the experience and data gained during phase one, it emerged that certain generic features of a task influenced PSF relevance. This led to the establishment of a finite set of generic task groups and response types. Similarly, certain PSFs influence some human errors more than others. The result was a set of error type key words, plus the identification and classification of error causes with their underlying error mechanisms. By linking all these aspects together, a comprehensive methodology has been forwarded as the basis of a computerized aid for system designers. To recapitulate, the major results of this research have been: One, the development of a comprehensive PSF listing specifically for the chemical process industries with a classification structure that facilitates future updates; and two, a model of identifying relevant SPFs and their order of priority. Future requirements are the evaluation of the PSF listing and the identification method. The latter must be considered both in terms of `useability' and its success as a design enhancer, in terms of an observable reduction in important human errors.

An assessment of the industry cluster approach as a tool for local economic development:the case of the new media industry in Birmingham

Industry cluster policies are a current trend in local economic development programmes and represent a major shift from traditional approaches. This trend has been coupled by an increasing interest in new media industry as a significant focus for regional development strategies. In England clusters and new media industry have therefore come to be seen as important tools in promoting local and regional economic development. This study aimed to ascertain the success of these policies. In order to achieve the aims of the study, the Birmingham new media industry was chosen for the study. In addition to an extensive review of the literature, semi-structured interviews were conducted with new media firms and Business Support Agencies (BSAs) offering programmes to promote the development of the new media industry cluster. The key findings of the thesis are that the concerns of new media industry when choosing their location do not conform to the industry cluster theory. Moreover, close proximity in geographical location of the industries does not mean there is collaboration and any costs saved as a result of close proximity to similar firms are at present seen as irrelevant because of the type of products they offer. Building trust between firms is the key in developing the new media industry cluster and the BSAs can act as a broker and provide neutral ground to develop it. The key policy recommendations are that new media industry is continually changing and research must continuously track and analyse cluster dynamics in order to be aware of emerging trends and future developments that can positively and negatively affect the cluster. Policy makers need to keep in mind that there is no uniform tool kit to foster the different sectors in cluster development. It is also important for them to be winning support and trust of new media firms since this is key in the success of the cluster. When cluster programs are introduced they must explain their benefits to industries more effectively in order to encourage them to participate in programmes. The general conclusions of the thesis are that clusters are a potentially important tool in local economic development policy and that the new media industry has a considerable growth potential. The kinds of relationships which cluster theory suggests develop between do not, as yet, appear to exist within the new media cluster. There are however, steps that the BSAs can take to encourage their development. Thus, the BSAs need to ensure that they establish an environment that enables growth of the industry.

Marketing strategy and new product development in the UK credit card industry

The development of new products in today's marketing environment is generally accepted as a requirement for the continual growth and prosperity of organisations. The literature is consequently rich with information on the development of various aspects of good products. In the case of service industries, it can be argued that new service product development is of as least equal importance as it is to organisations that produce tangible goods products. Unlike the new goods product literature, the literature on service marketing practices, and in particular, new service product development, is relatively sparse. The main purpose of this thesis is to examine a number of aspects of new service product development practice with respect to financial services and specifically, credit card financial services. The empirical investigation utilises both a case study and a survey approach, to examine aspects of new service product development industry practice relating specifically to gaps and deficiencies in the literature with respect to the financial service industry. The findings of the empirical work are subsequently examined in the context in which they provide guidance and support for a new normative new service product development model. The study examines the UK credit card financial service product sector as an industry case study and perspective. The findings of the field work reveal that the new service product development process is still evolving, and that in the case of credit card financial services can be seen as a well-structured and well-documented process. New product development can also be seen as an incremental, complex, interactive and continuous process which has been applied in a variety of ways. A number of inferences are subsequently presented.

Environmental features which limit organization and industry viability:a study of the footwear industry

This thesis proposes a conceptual framework for the analysis of organizational environments. Three primary segments of the task environment - the transaction environment, the industrial environment and the ecotone are delineated. The interrelationships between the organization and these three environmental segments are examined. It is suggested that the task environment i) defines the nature of the task confronting the organization and the economic, political and social position of the organization within this network; ii) influences the way organizations and industries are organized; iii) prevents recognition of the need for adaptation and change; and iv) limits the alternatives available to the organization should changes in the environment render existing technology, behaviour and structures obsolete. The British Footwear Industry provides an example of how this framework might be used to investigate the problem of industry decline and organization viability. It is argued that the explanations usually put forth to explain organization failure and industrial decline have not taken into consideration the environmental factors which affect organization and industry viability. The shift from national markets to global markets has altered the composition of the task environment and has changed the nature of competition from firm versus firm to environment versus environment. Organizations do not compete in the market, their products do. These products are often produced by organizations embedded in environments which are significantly different from the one in which the focal organization and industry are embedded.

Setting parameters in MRP for the effective management of bought-out inventory in a JIT assembly environment

In recent years, UK industry has seen an explosive growth in the number of `Computer Aided Production Management' (CAPM) system installations. Of the many CAPM systems, materials requirement planning/manufacturing resource planning (MRP/MRPII) is the most widely implemented. Despite the huge investments in MRP systems, over 80 percent are said to have failed within 3 to 5 years of installation. Many people now assume that Just-In-Time (JIT) is the best manufacturing technique. However, those who have implemented JIT have found that it also has many problems. The author argues that the success of a manufacturing company will not be due to a system which complies with a single technique; but due to the integration of many techniques and the ability to make them complement each other in a specific manufacturing environment. This dissertation examines the potential for integrating MRP with JIT and Two-Bin systems to reduce operational costs involved in managing bought-out inventory. Within this framework it shows that controlling MRP is essential to facilitate the integrating process. The behaviour of MRP systems is dependent on the complex interactions between the numerous control parameters used. Methodologies/models are developed to set these parameters. The models are based on the Pareto principle. The idea is to use business targets to set a coherent set of parameters, which not only enables those business targets to be realised, but also facilitates JIT implementation. It illustrates this approach in the context of an actual manufacturing plant - IBM Havant. (IBM Havant is a high volume electronics assembly plant with the majority of the materials bought-out). The parameter setting models are applicable to control bought-out items in a wide range of industries and are not dependent on specific MRP software. The models have produced successful results in several companies and are now being developed as commercial products.

Aspects of the design and operation of production control systems in manufacturing industry

Computerised production control developments have concentrated on Manufacturing Resources Planning (MRP II) systems. The literature suggests however, that despite the massive investment in hardware, software and management education, successful implementation of such systems in manufacturing industries has proved difficult. This thesis reviews the development of production planning and control systems, in particular, investigates the causes of failures in implementing MRP/MRP II systems in industrial environments and argues that the centralised and top-down planning structure, as well as the routine operational methodology of such systems, is inherently prone to failure. The thesis reviews the control benefits of cellular manufacturing systems but concludes that in more dynamic manufacturing environments, techniques such as Kanban are inappropriate. The basic shortcomings of MRP II systems are highlighted and a new enhanced operational methodology based on distributed planning and control principles is introduced. Distributed Manufacturing Resources Planning (DMRP), was developed as a capacity sensitive production planning and control solution for cellular manufacturing environments. The system utilises cell based, independently operated MRP II systems, integrated into a plant-wide control system through a Local Area Network. The potential benefits of adopting the system in industrial environments is discussed and the results of computer simulation experiments to compare the performance of the DMRP system against the conventional MRP II systems presented. DMRP methodology is shown to offer significant potential advantages which include ease of implementation, cost effectiveness, capacity sensitivity, shorter manufacturing lead times, lower working in progress levels and improved customer service.

The interaction between the implementation of an occupational health and safety management system and safety culture:a case study in the rubber industry

A prominent theme emerging in Occupational Health and Safety (OSH) is the development of management systems. A range of interventions, according to a prescribed route detailed by one of the management systems, can be introduced into an organisation with some expectation of improved OSH performance. This thesis attempts to identify the key influencing factors that may impact upon the process of introducing interventions, (according to B88800: 1996, Guide to Implementing Occupational Health and Safety Management Systems) into an organisation. To help identify these influencing factors a review of possible models from the sphere of Total Quality Management (TQM) was undertaken and the most suitable TQM model selected for development and use in aSH. By anchoring the aSH model's development in the reviewed literature a range ofeare, medium and low level influencing factors were identified. This model was developed in conjunction with the research data generated within the case study organisation (rubber manufacturer) and applied to the organisation. The key finding was that the implementation of an OSH intervention was dependant upon three broad vectors of influence. These are the Incentive to introduce change within an organisation which refers to the drivers or motivators for OSH. Secondly the Ability within the management team to actually implement the changes refers to aspects, amongst others, such as leadership, commitment and perceptions of OSH. Ability is in turn itself influenced by the environment within which change is being introduced. TItis aspect of Receptivity refers to the history of the plant and characteristics of the workforce. Aspects within Receptivity include workforce profile and organisational policies amongst others. It was found that the TQM model selected and developed for an OSH management system intervention did explain the core influencing factors and their impact upon OSH performance. It was found that within the organisation the results that may have been expected from implementation of BS8800:1996 were not realised. The OSH model highlighted that given the organisation's starting point, a poor appreciation of the human factors of OSH, gave little reward for implementation of an OSH management system. In addition it was found that general organisational culture can effectively suffocate any attempts to generate a proactive safety culture.

Energy conservation in the steel industry

The last few years have witnessed an unprecedented increase in the price of energy available to industry in the United Kingdom and worldwide. The steel industry, as a major consumer of energy delivered in U.K. (8% of national total and nearly 25% of industrial total) and whose energy costs currently form some 28% of the total manufacturing cost, is very much aware of the need to conserve energy. Because of the complexities of steelmaking processes it is imperative that a full understanding of each process and its interlinking role in an integrated steelworks is understood. An analysis of energy distribution shows that as much as 70% of heat input is dissipated to the environment in a variety of forms. Of these, waste gases offer the best potential for energy conservation. The study identifies areas for and discusses novel methods of energy conservation in each process. Application of these schemes in BSC works is developed and their economic incentives highlighted. A major part of this thesis describes design, development and testing of a novel ceramic rotary regenerator for heat recovery from high temperature waste gases, where no such system is available. The regenerator is a compact, efficient heat exchanger. Application of such a system to a reheating furnace provides a fuel saving of up to 40%. A mathematical model developed is verified on the pilot plant. The results obtained confirm the success of the concept and material selection and outlines the work needed to develop an industrial unit. Last, but not least, the key position of an energy manager in an energy conservation programme is identified and a new Energy Management Model for the BSC is developed.

The control of technological change in the motor industry:a case study

This thesis is based upon a case study of the introduction of automated production technologies at the Longbridge plant of British Leyland in the period 1978 to 1980.The investment in automation was part of an overall programme of modernization to manufacture the new 'Mini Metro' model. In the first Section of the thesis, the different theoretical perspectives on technological change are discussed. Particular emphasis is placed upon the social role of management as the primary controllers of technological change. Their actions are seen to be oriented towards the overall strategy of the firm, integrating the firm's competitive strategy with production methods and techniques.This analysis is grounded in an examination of British Leyland's strategies during the 1970s.. The greater part of the thesis deals with the efforts made by management to secure their strategic objectives in the process of technological change against the conflicting claims of their work-force. Examination of these efforts is linked to the development of industrial relations conflict at Longbridge and in British Leyland as a whole.Emphasis is placed upon the struggle between management in pursuit of their version of efficiency and the trade unions in defence of job controls and demarcations. The thesis concludes that the process of technological change in the motor industry is controlled by social forces,with the introduction of new technologies being closely intertwined with management!s political relations with the trade unions.

Automation, rationalisation and concentration : a case study in the British chemical industry

This thesis is based upon a case study of the adoption of digital, electronic, microprocessor-based control systems by Albright & Wilson Limited - a UK chemical producer. It offers an explanation of the company's changing technology policy between 1978 and 1981, by examining its past development, internal features and industrial environment. Part One of the thesis gives an industry-level analysis which relates the development of process control technology to changes in the economic requirements of production . The rapid diffusion of microcomputers and other microelectronic equipment in the chemical industry is found to be a response to general need to raise the efficiency of all processes, imposed by the economic recession following 1973. Part Two examines the impaot of these technical and eoonomic ohanges upon Albright & Wilson Limited. The company's slowness in adopting new control technology is explained by its long history in which trends are identified whlich produced theconservatism of the 1970s. By contrast, a study of Tenneco Incorporated, a much more successful adoptor of automating technology, is offered with an analysis of the new technology policy of adoption of such equipment which it imposed upon Albright & Wilson, following the latter's takeover by Tenneco in 1978. Some indications of the consequences by this new policy of widespread adoptions of microprocessor-based control equipment are derived from a study of the first Albright & Wilson plant to use such equipment. The thesis concludes that companies which fail to adopt rapidly the new control technology may not survive in the recessionary environment, the long- established British companies may lack the flexibility to make such necessary changes and that multi-national companies may have an important role jn the planned transfer and adoption of new production technology through their subsidiaries in the UK.

Investigative framework for research into the design of manufacturing processes

This paper is based a major research project run by a team from the Innovation, Design and Operations Management Research Unit at the Aston Business School under SERC funding. International Computers Limited (!CL), the UK's largest indigenous manufacturer of mainframe computer products, was the main industrial collaborator in the research. During the period 1985-89 an integrated production system termed the "Modular Assembly Cascade'' was introduced to the Company's mainframe assembly plant at Ashton-under-Lyne near Manchester. Using a methodology primarily based upon 'participative observation', the researchers developed a model for analysing this manufacturing system design called "DRAMA". Following a critique of the existing literature on Manufacturing Strategy, this paper will describe the basic DRAMA model and its development from an industry specific design methodology to DRAMA II, a generic model for studying organizational decision processes in the design and implementation of production systems. From this, the potential contribution of the DRAMA model to the existing knowledge on the process of manufacturing system design will be apparent.

Global marketing of industrial products:are interpersonal relationships always critical?

The present paper examines the issue of whether interpersonal relationships are critical for global marketing of industrial products. The fields of relationship marketing, IMP group research, sales research, and network theory have stressed the importance of interpersonal relationships in the business-to-business or industrial marketing context. In contrast to this emphasis on interpersonal relationships, we argue that industrial firms can both conceive and enhance marketing strategies based on developing high quality and consistent processes, products, services or outcomes (consistent processes and outcomes). Such strategies are especially important given the fact that developing interpersonal relationships is expensive due to their reliance on frequent and/or face-to-face communications. In this paper, we examine industry and country contexts that lead to the choice of alternative industrial product marketing strategies and highlight some future research directions and managerial implications.

Sustainable energy from paper industry wastes

Secondary fibre paper mills are significant users of both heat and electricity which is mainly derived from the combustion of fossil fuels. The cost of producing this energy is increasing year upon year. These mills are also significant producers of fibrous sludge and reject waste material which can contain high amounts of useful energy. Currently the majority of these waste fractions are disposed of by landfill, land-spread or incineration using natural gas. These disposal methods not only present environmental problems but are also very costly. The focus of this work was to utilise the waste fractions produced at secondary fibre paper mills for the on-site production of combined heat and power (CHP) using advanced thermal conversion methods (gasification and pyrolysis), well suited to relatively small scales of throughput. The heat and power can either be used on-site or exported. The first stage of the work was the development of methods to condition selected paper industry wastes to enable thermal conversion. This stage required detailed characterisation of the waste streams in terms of proximate and ultimate analysis and heat content. Suitable methods to dry and condition the wastes in preparation for thermal conversion were also explored. Through trials at pilot scale with both fixed bed downdraft gasification and intermediate pyrolysis systems, the energy recovered from selected wastes and waste blends in the form of product gas and pyrolysis products was quantified. The optimal process routes were selected based on the experimental results, and implementation studies were carried out at the selected candidate mills. The studies consider the pre-processing of the wastes, thermal conversion, and full integration of the energy products. The final stage of work was an economic analysis to quantify economic gain, return on investment and environmental benefits from the proposed processes.

8 steps for managing green innovation in the automotive industry

The car is dead, long live the car! We are about to celebrate 100 years of Ford model T, the most iconic symbol of the popularisation of cars as the means of personal mobility. The automotive industry is going through an incredible journey of redefining its purpose and the traditional characteristics of its products. More than ever, car manufacturers will need to develop and effectively implement a meaningful green innovation strategy if they want to survive in the new automotive era.