Evaluation of strontium-site-deficient Sr2Fe1.4Co0.1Mo0.5O6-δ-based perovskite oxides as intermediate temperature solid oxide fuel cell cathodes

In this paper strontium-site-deficient Sr₂Fe_1.4Co_0.1Mo_0.5O_6-δ-based perovskite oxides (S_xFCM) were prepared and evaluated as the cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFCs). All samples exhibited a cubic phase structure and the lattice shrinked with increasing the Sr-deficiency as shown in XRD patterns. XPS results determined that the transition elements (Co/Fe/Mo) in S_xFCM oxides were in a mixed valence state, demonstrating the small polaron hopping conductivity mechanism existed. Among the samples, S_1.950FCM presented the lowest coefficient of thermal expansion of 15.62 × 10^-6 K^-1, the highest conductivity value of 28 S cm^-1 at 500 °C, and the lowest interfacial polarization resistance of 0.093 Ω cm² at 800 °C, respectively. Furthermore, an anode-supported single cell with a S_1.950FCM cathode was prepared, demonstrating a maximum power density of 1.16 W cm^-2 at 800 °C by using wet H₂ (3% H₂O) as the fuel and ambient air as the oxidant. These results indicate that the introduction of Sr-deficiency can dramatically improve the electrochemical performance of Sr₂Fe_1.4Co_0.1Mo_0.5O_6-δ, showing great promise as a novel cathode candidate material for IT-SOFCs.

Fabrication and evaluation of NiO/Y2O3-stabilized-ZrO2 hollow fibers for anode-supported micro-tubular solid oxide fuel cells

In this work NiO/3mol% Y₂O₃-ZrO₂ (3YSZ) and NiO/8mol% Y₂O₃-ZrO₂ (8YSZ) hollow fibers were prepared by phase-inversion. The effect of different kinds of YSZ (3YSZ and 8YSZ) on the porosity, electrical conductivity, shrinkage and flexural strength of the hollow fibers were systematically evaluated. When compared with Ni-8YSZ the porosity and shrinkage of Ni-3YSZ hollow fibers increases while the electrical conductivity decreases, while at the same time also exhibiting enhanced flexural strength. Single cells with Ni-3YSZ and Ni-8YSZ hollow fibers as the supported anode were successfully fabricated showing maximum power densities of 0.53 and 0.67Wcm^-2 at 800°C, respectively. Furthermore, in order to improve the cell performance, a Ni-8YSZ anode functional layer was added between the electrolyte and Ni-YSZ hollow fiber. Here enhanced peak power densities of 0.79 and 0.73Wcm^-2 were achieved at 800°C for single cells with Ni-3YSZ and Ni-8YSZ hollow fibers, respectively.

In vitro and in vivo evaluation of lyophilized bioprosthetic valve

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Evaluation of the Chemical Durability of Iowa Fly Ash Concretes, HR-327, Phase I Progress Report, 1991

The following report summarizes research activities conducted on Iowa Department of Transportation Project HR-327, for the period April 1, 1990 through March 31, 1991. The purpose of this research project is to investigate how fly ash influences the chemical durability of portland cement based materials. The goal of this research is to utilize the empirical information obtained from laboratory testing to better estimate the durability of portland cement concrete pavements (with and without fly ash) subjected to chemical attack via the natural environment or the application of deicing salts. This project is being jointly sponsored by the Iowa Department of Transportation and the Iowa Fly Ash Affiliate Research group. The research work is also being cooperatively conducted by Iowa State University and Iowa Department of Transportation research personnel. Researchers at Iowa State University are conducting the paste and mortar studies while Iowa Department of Transportation researchers are conducting the concrete study.

Manipulation in U.S. REIT Investment Performance Evaluation: Empirical Evidence

We investigate whether Real Estate Investment Trust (REIT) managers actively manipulate performance measures in spite of the strict regulation under the REIT regime. We provide empirical evidence that is consistent with this hypothesis. Specifically, manipulation strategies may rely on the opportunistic use of leverage. However, manipulation does not appear to be uniform across REIT sectors and seems to become more common as the level of competition in the underlying property sector increases. We employ a set of commonly used traditional performance measures and a recently developed manipulation-proof measure (MPPM, Goetzmann, Ingersoll, Spiegel, and Welch (2007)) to evaluate the performance of 147 REITs from seven different property sectors over the period 1991-2009. Our findings suggest that the existing REIT regulation may fail to mitigate a substantial agency conflict and that investors can benefit from evaluating return information carefully in order to avoid potentially manipulative funds.

Evaluation of a Quality Improvement (QI) Intervention for Maternal, Newborn, and Child Health (MNCH) in Colombia: The Mil Días Intervention of SINERGIAS in the Department of Bolívar

Thesis (Master's)--University of Washington, 2016-06

The Performance Characteristics of a Surface-Modified Cutting Tool

In the past, many papers have been presented which show that the coating of cutting tools often yields decreased wear rates and reduced coefficients of friction. Although different theories are proposed, covering areas such as hardness theory, diffusion barrier theory, thermal barrier theory, and reduced friction theory, most have not dealt with the question of how and why the coating of tool substrates with hard materials such as Titanium Nitride (TiN), Titanium Carbide (TiC) and Aluminium Oxide (Al203) transforms the performance and life of cutting tools. This project discusses the complex interrelationship that encompasses the thermal barrier function and the relatively low sliding friction coefficient of TiN on an undulating tool surface, and presents the result of an investigation into the cutting characteristics and performance of EDMed surface-modified carbide cutting tool inserts. The tool inserts were coated with TiN by the physical vapour deposition (PVD) method. PVD coating is also known as Ion-plating which is the general term of the coating method in which the film is created by attracting ionized metal vapour in this the metal was Titanium and ionized gas onto negatively biased substrate surface. Coating by PVD was chosen because it is done at a temperature of not more than 5000C whereas chemical Vapour Deposition CVD process is done at very high temperature of about 8500C and in two stages of heating up the substrates. The high temperatures involved in CVD affects the strength of the (tool) substrates. In this study, comparative cutting tests using TiN-coated control specimens with no EDM surface structures and TiN-coated EDMed tools with a crater-like surface topography were carried out on mild steel grade EN-3. Various cutting speeds were investigated, up to an increase of 40% of the tool manufacturer’s recommended speed. Fifteen minutes of cutting were carried out for each insert at the speeds investigated. Conventional tool inserts normally have a tool life of approximately 15 minutes of cutting. After every five cuts (passes) microscopic pictures of the tool wear profiles were taken, in order to monitor the progressive wear on the rake face and on the flank of the insert. The power load was monitored for each cut taken using an on-board meter on the CNC machine to establish the amount of power needed for each stage of operation. The spindle drive for the machine is an 11 KW/hr motor. Results obtained confirmed the advantages of cutting at all speeds investigated using EDMed coated inserts, in terms of reduced tool wear and low power loads. Moreover, the surface finish on the workpiece was consistently better for the EDMed inserts. The thesis discusses the relevance of the finite element method in the analysis of metal cutting processes, so that metal machinists can design, manufacture and deliver goods (tools) to the market quickly and on time without going through the hassle of trial and error approach for new products. Improvements in manufacturing technologies require better knowledge of modelling metal cutting processes. Technically the use of computational models has a great value in reducing or even eliminating the number of experiments traditionally used for tool design, process selection, machinability evaluation, and chip breakage investigations. In this work, much interest in theoretical and experimental investigations of metal machining were given special attention. Finite element analysis (FEA) was given priority in this study to predict tool wear and coating deformations during machining. Particular attention was devoted to the complicated mechanisms usually associated with metal cutting, such as interfacial friction; heat generated due to friction and severe strain in the cutting region, and high strain rates. It is therefore concluded that Roughened contact surface comprising of peaks and valleys coated with hard materials (TiN) provide wear-resisting properties as the coatings get entrapped in the valleys and help reduce friction at chip-tool interface. The contributions to knowledge: a. Relates to a wear-resisting surface structure for application in contact surfaces and structures in metal cutting and forming tools with ability to give wear-resisting surface profile. b. Provide technique for designing tool with roughened surface comprising of peaks and valleys covered in conformal coating with a material such as TiN, TiC etc which is wear-resisting structure with surface roughness profile compose of valleys which entrap residual coating material during wear thereby enabling the entrapped coating material to give improved wear resistance. c. Provide knowledge for increased tool life through wear resistance, hardness and chemical stability at high temperatures because of reduced friction at the tool-chip and work-tool interfaces due to tool coating, which leads to reduced heat generation at the cutting zones. d. Establishes that Undulating surface topographies on cutting tips tend to hold coating materials longer in the valleys, thus giving enhanced protection to the tool and the tool can cut faster by 40% and last 60% longer than conventional tools on the markets today.

Evaluation of Bond Retainage in Portland Cement Concrete Overlays by Infrared Thermography and Ground Penetrating Radar, HR-537, 1988

The purpose of this project was to evaluate the location and quantities of debonding in selected portland cement concrete (PCC) overlays. The project entailed an infrared thermographic survey and a ground penetrating radar survey of the PCC overlays to locate areas of debonding between the overlays and the original pavement. An infrared scanner is capable of locating these areas because of the temperature differential which is established between bonded and debonded areas under certain environmental conditions. A conventional video inspection of the top surface of the pavement was also completed in conjunction with the infrared thermographic survey to record the visual condition of the pavement surface. The ground penetrating radar system is capable of locating areas of debonding by detecting return wave forms generated by changes in the dielectric properties at the PCC overlay original pavement interface. This report consists of two parts; a text and a set of plan sheets. The text summarizes the procedures, analyses and conclusions of the investigation. The plan sheets locate specific areas of debonding, as identified through field observations.

Evaluation of One-Dimensional Seismic Site Response Analyses at Small to Large Strain Levels

Thesis (Master's)--University of Washington, 2016-08

Evaluation of control devices for asphalt pavement recycling operations : summary report for research project HR-188, 1982

The objective of the research project was to seek acceptable solutions to the air pollution problem created in the asphalt recycling process using modified conventional equipment.

An Evaluation of Tail Loss Recovery Mechanisms for TCP

Interactive applications do not require more bandwidth to go faster. Instead, they require less latency. Unfortunately, the current design of transport protocols such as TCP limits possible latency reductions. In this paper we evaluate and compare different loss recovery enhancements to fight tail loss latency. The two recently proposed mechanisms "RTO Restart" (RTOR) and "Tail Loss Probe" (TLP) as well as a new mechanism that applies the logic of RTOR to the TLP timer management (TLPR) are considered. The results show that the relative performance of RTOR and TLP when tail loss occurs is scenario dependent, but with TLP having potentially larger gains. The TLPR mechanism reaps the benefits of both approaches and in most scenarios it shows the best performance.

Evaluation of processed groundnut (Arachis hypogaea) cake meals in the feeding of Clariid catfish, Clarias gariepinus, fingerlings

Groundnut cake (GNC) meal is an important source of dietary protein for domestic animals with a cost advantage over the conventional animal protein sources used in aquaculture feed production. It would be useful to evaluate the effects of GNC processing methods on the density and nutritional values of processed GNC meals. The use of processed GNC meals in the diets of Clarias gariepinus fingerlings was evaluated. Seven iso-proteic and iso-caloric diets were formulated, replacing fish meal with roasted and boiled GNC meals, each at three inclusion levels of 30%, 35%, and 40%. Diet I is 100% fishmeal, Diet II is 30% roasted GNC meal, Diet III is 35% roasted GNC meal, Diet IV is 40% roasted GNC meal, Diet V is 30% boiled GNC meal, Diet VI is 35% boiled GNC meal and Diet VII is 40% boiled GNC meal. Results showed that the crude protein content of GNC meals was 40.5% and 40.8% in boiled and roasted GNC meals respectively; the lower protein content for processed GNC meals might be due to heat denaturation of the seed protein, with boiled GNC meal being more adversely affected. The mean weight gain of fingerlings fed roasted GNC meals ranged between 5.29 – 5.64 while for boiled GNC meals, it was between 4.60 – 5.22. Generally, fish performed better when fed diets containing roasted GNC meals, than boiled GNC meals, and compared favorably with fish fed fish meal based diet. Body mass increase, total feed increase, protein efficiency ratio and specific growth rate by C. gariepinus fingerlings in all diets, showed no significant differences, suggesting that processed GNC meals could partially replace diets for C. gariepinus fingerlings without adverse consequences. This study showed that processed GNC meals could partially replace fish meal up to 30% without significantly influencing fingerling growth and health. It is recommended that the use of fish meal as the main basal ingredient for fingerlings could be discontinued, since GNC meal was a cheaper alternative, and could replace fish meal up to 35%, without any significant adverse effects on the fingerling performance. KEYWORDS: Clarias gariepinus, Fingerlings, Groundnut cake meal, Nutrient utilization, Performance.

International comparative field evaluation of a traffic-responsive signal control strategy in three cities

The recently developed network-wide real-time signal control strategy TUC has been implemented in three traffic networks with quite different traffic and control infrastructure characteristics: Chania, Greece (23 junctions); Southampton, UK (53 junctions); and Munich, Germany (25 junctions), where it has been compared to the respective resident real-time signal control strategies TASS, SCOOT and BALANCE. After a short outline of TUC, the paper describes the three application networks; the application, demonstration and evaluation conditions; as well as the comparative evaluation results. The main conclusions drawn from this high-effort inter-European undertaking is that TUC is an easy-to-implement, inter-operable, low-cost real-time signal control strategy whose performance, after very limited fine-tuning, proved to be better or, at least, similar to the ones achieved by long-standing strategies that were in most cases very well fine-tuned over the years in the specific networks.

Comparative field evaluation of the signal control strategy TUC in three traffic networks.

This paper describes how the recently developed network-wide real-time signal control strategy TUC has been implemented in three traffic networks with quite different traffic and control infrastructure characteristics: Chania, Greece (23 junctions); Southampton, U.K. (53 junctions); and Munich, Germany (25 junctions), where it has been compared to the respective resident real-time signal control strategies TASS, SCOOT and BALANCE. After a short outline of TUC, the paper describes the three application networks; the application, demonstration and evaluation conditions; as well as the comparative evaluation results. The main conclusions drawn from this high-effort inter-European undertaking is that TUC is an easy-to-implement, inter-operable, low-cost real-time signal control strategy whose performance, after limited fine-tuning, proved to be better or, at least, similar to the ones achieved by long-standing strategies that were in most cases very well fine-tuned over the years in the specific networks.