The Comprehensive Standardization of the Graphic Industry Production Chain in the Printing House

The purpose of this thesis was to investigate Job Definition Format (JDF) and how it could be used in printing house's systems. JDF is a very new information exchange standard, and it gives a lot of opportunities to the printing industry. JDF is the first standard, that has an ability to carry a print job from genesis through completion. Besides, JDF has an ability to bridge the communication gap between production and management information services. In the study of JDF we focused on examining how JDF will effect on printing industry .The thesis also examines printing houses's systems ability to work with JDF standard. The result of the study is a comprehensive picture, what is JDF. We also researched the system developers' visions, how JDF will effect on their products in the future.

Sähköisen liikkeenohjauskäytön mitoitus, käyttöönoton dokumentointi ja pakkauslinjasovellukset

Frequency converters have started to gain new market areas in the field of motion control applications. The communication and control properties of frequency converters have reached the properties of traditional servo amplifiers during the past few years. In this thesis a motion control system was examined. This particular system consists of frequency converters, permanent magnet synchronous motors and linear belt drives. The properties and prerequisites for packing are discussed. A test setup was build and measurement sets were done to examine the performance of the system. Speed and accuracy measurements were done in all three dimensions. Based on the measurement results applicability of the system for packing industry was evaluated.

Poly(butylene terephthalate-co-5-tert-butyl isophthalate) Copolyesters: Synthesis, Characterization and Properties

A series of poly(butylene terephthalate) copolyesters containing 5-tert-butyl isophthalate units up to 50%-mole, as well as the homopolyester entirely made of these units, were prepared by polycondensation from the melt. The microstructure of the copolymers was determined by NMR to be at random for the whole range of compositions. The effect exerted by the 5-tert-butyl isophthalate units on thermal, tensile and gas transport properties was evaluated. Both Tm and crystallinity as well as the mechanical moduli were found to decrease steadily with copolymerization whereas Tg increased and the polyesters became more brittle. Permeability and solubility sligthly increased also with the content in substituted units whereas the diffusion coefficient remained practically constant. For the homopolyester poly(5-tert-butyl isophthalate), all these properties were found to deviate significantly from the general trend displayed by copolyesters suggesting that a different chain mode of packing in the amorphous phase is likely adopted in this case.

Brightness of multilayer boards

A good appearance of a package enhances the sale of the product. The packing gives information about the content and instructions for the usage. In this master’s thesis, the optical properties of multilayer packaging board is studied. Especially means of increasing brightness of the multilayer board are evaluated. In the literature part, the effect of different factors on optical properties of a multilayer board are evaluated with the help of light scattering and absorption coefficients. The Kubelka-Munk theory can be used also in modelling brightness of the multilayer board. A large variety of different process factors, chemical aids and machine variables affect optical properties of board. In the experimental part, different methods to increase brightness of a 3-layer board were evaluated. It was discovered that brightness variation of broke (30 % share of the center layer pulp) have only minor influence on brightness of the board. The brightness variation must be high, roughly 9 % in order to alter brightness of the board by 1 %. Higher brightness can be achieved by bleaching the pulp, which holds the largest share of the center layer pulp. Here, 2,6 % increase in brightness of the pulp (60 % share of the center layer pulp) increased brightness of the board by 1 %. In a trial run at a board machine, there was no indication of decreased bulk of the board due to extended bleaching of the pulp. With pulp dyeing appearance and optical properties of a multilayer board can be influenced. By using bluish dyes the natural yellowness of pulps can be decreased and impression of whiteness is then increased. Brightness may deteriorate though, because of increasing light absorption of the dyed pulps. When the yellowness comes from the center layer pulp, the dye should be introduced there. Then the brightness decreasing effect of the dye decreases brightness of the board less. It was noticed that it is more important to maintain brightness of the top layer than brightness of the center layer, because the top layer pulp affects on brightness of the board the most. By introducing fillers into the top layer of a multilayer board it is possible to increase brightness of the board. Fillers with the highest light scattering increased the brightness of the board the most. Increasing light scattering increases brightness and also opacity. Higher opacity in the top layer decreases also the darkening effect of the center layer. Calcinated kaolin and PCC was found to increase the light scattering of the top layer the most at the filler comparison. Introducing fillers into the top layer of multilayer board may decrease bulk and modulus of elasticity of the top layer. This could lead to deteriorated bending stiffness.

Streptavidin - A Versatile Binding Protein for Solid-Phase Immunoassays

Streptavidin, a tetrameric protein secreted by Streptomyces avidinii, binds tightly to a small growth factor biotin. One of the numerous applications of this high-affinity system comprises the streptavidin-coated surfaces of bioanalytical assays which serve as universal binders for straightforward immobilization of any biotinylated molecule. Proteins can be immobilized with a lower risk of denaturation using streptavidin-biotin technology in contrast to direct passive adsorption. The purpose of this study was to characterize the properties and effects of streptavidin-coated binding surfaces on the performance of solid-phase immunoassays and to investigate the contributions of surface modifications. Various characterization tools and methods established in the study enabled the convenient monitoring and binding capacity determination of streptavidin-coated surfaces. The schematic modeling of the monolayer surface and the quantification of adsorbed streptavidin disclosed the possibilities and the limits of passive adsorption. The defined yield of 250 ng/cm² represented approximately 65 % coverage compared with a modelled complete monolayer, which is consistent with theoretical surface models. Modifications such as polymerization and chemical activation of streptavidin resulted in a close to 10-fold increase in the biotin-binding densities of the surface compared with the regular streptavidin coating. In addition, the stability of the surface against leaching was improved by chemical modification. The increased binding densities and capacities enabled wider high-end dynamic ranges in the solid-phase immunoassays, especially when using the fragments of the capture antibodies instead of intact antibodies for the binding of the antigen. The binding capacity of the streptavidin surface was not, by definition, predictive of the low-end performance of the immunoassays nor the assay sensitivity. Other features such as non-specific binding, variation and leaching turned out to be more relevant. The immunoassays that use a direct surface readout measurement of time-resolved fluorescence from a washed surface are dependent on the density of the labeled antibodies in a defined area on the surface. The binding surface was condensed into a spot by coating streptavidin in liquid droplets into special microtiter wells holding a small circular indentation at the bottom. The condensed binding area enabled a denser packing of the labeled antibodies on the surface. This resulted in a 5 - 6-fold increase in the signal-to-background ratios and an equivalent improvement in the detection limits of the solid-phase immunoassays. This work proved that the properties of the streptavidin-coated surfaces can be modified and that the defined properties of the streptavidin-based immunocapture surfaces contribute to the performance of heterogeneous immunoassays.

Elecció d'un ERP en base a l'optimització de processos informàtics en una indústria càrnia

Elecció d'un ERP en base a l'estudi de processos òptims per a la indústria càrnia.

Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.

Coolant Flow and Heat Transfer in Pebble-Bed Reactor Core

This thesis gathers knowledge about ongoing high-temperature reactor projects around the world. Methods for calculating coolant flow and heat transfer inside a pebble-bed reactor core are also developed. The thesis begins with the introduction of high-temperature reactors including the current state of the technology. Process heat applications that could use the heat from a high-temperature reactor are also introduced. A suitable reactor design with data available in literature is selected for the calculation part of the thesis. Commercial computational fluid dynamics software Fluent is used for the calculations. The pebble-bed is approximated as a packed-bed, which causes sink terms to the momentum equations of the gas flowing through it. A position dependent value is used for the packing fraction. Two different models are used to calculate heat transfer. First a local thermal equilibrium is assumed between the gas and solid phases and a single energy equation is used. In the second approach, separate energy equations are used for the phases. Information about steady state flow behavior, pressure loss, and temperature distribution in the core is obtained as results of the calculations. The effect of inlet mass flow rate to pressure loss is also investigated. Data found in literature and the results correspond each other quite well, considered the amount of simplifications in the calculations. The models developed in this thesis can be used to solve coolant flow and heat transfer in a pebble-bed reactor, although additional development and model validation is needed for better accuracy and reliability.

AR 117: viviendas en Alcázar de San Juan

Postprint (published version)

ETÓ_04_AMPOSTA: habitatges a Amposta, Tarragona

Postprint (published version)

Energiatehokkuuden edistäminen rakentamisen ja asumisen alalla

Suomi haluaa energiatehokkuuden edelläkävijäksi maailmassa, mutta se ei onnistu ilman rakennusalan osallistumista energiatehokkuustalkoisiin. Toistaiseksi energiatehokkuuden kehitys asumisen ja rakentamisen osalta ei ole ollut niin nopeaa kuin muualla Euroopassa. Energiatehokkuustalkoiden takana on huoli ilmastomuutoksen vaikutuksista. Ilmastomuutoksen torjuminen aiheuttaa yhteiskunnalle kustannuksia, mutta pidemmällä aikavälillä se on halvempaa kuin puuttumatta jättäminen. Omakotitalojen suosio lisääntyy koko ajan ja energian kulutus niissä kasvaa. Erityisesti sähkönkäyttö lisääntyy koko ajan erityisesti viihde-elektroniikan suosion myötä. Energiatehokkuuteen yritetään vaikuttaa monenlaisilla ohjauskeinoilla, joita ovat muun muassa taloudelliset ja lainsäädännölliset ohjauskeinot. Lainsäädännön lisäksi yksi tärkeimmistä kannustimista energiatehokkuuteen on öljyn hinta. Rakennusten energiatehokkuudessa kokonaisuus ratkaisee ja erityisesti tiiveys. Julkisen sektorin rooli energiatehokkuuden edistämisessä on merkittävä sekä säädösten laatijana että esimerkin näyttäjänä. Vastuuta ilmastotalkoista halutaan jakaa myös kunnille.

Studies of Liquid-liquid Separation in Fibre Coalescer

This thesis focuses on fibre coalescers whose efficiency is based on the surface properties/characteristics. They have the ability to preferentially wet or interact with one or more of the fluids to be separated. Thus, the interfacial phenomena governing the separation efficiency of the coalescers is investigated depending on physical factors such as flowrates, phase ratios and coalescer packing density. Design of process equipment to produce and separate of the emulsions was carried out.The experimentation was carried out to test the separation efficiency of the coalescing medias, namely fibreglass, polyester I and polyester II. The performances of the coalescing medias were assessed via droplet size information. In conclusion, the objectives (design of process equipment and experimentation) were achieved. Fibre glass was the best coalescing media, next was polyester I and then finally polyester II. Droplets sizes increased with decreased flowrates and increased packing density of the coalescer. Phase ratio had effect on the droplet sizes of the feed but had no effect on the coalescence of droplets of the feed.

Correlação entre a estrutura atômica superficial e o processo de adsorção-dessorção reversível de hidrogênio em eletrodos monocristalinos Pt(111), Pt(100) e Pt(110)

Platinum is widely used as electrode in electrocatalytic processes, however the use of polycrystalline electrodes introduces a series of variables in the electrochemical system due to the aleatory contribution of all the crystallographic orientations with different surface packing of atoms. Single crystal platinum electrodes of low Miller index present surface structure of high regularity and serve as model to establish a correlation among the macroscopic and microscopic properties of the electrochemical interface. Therefore, the main aim of this work is the study of the voltammetric profiles of the reversible adsorption-desorption of hydrogen on Pt(100), Pt(110) and Pt(111), in order to correlate the electrochemical properties of each different orientation with the surface atomic structure.

Pientalojen ilmalämpöpumput sähköverkossa

Työssä tutkitaan ilmalämpöpumppujen kokonaisvaltaista vaikutusta sähköverkkoon. Tarkastelu aloitetaan lämpöpumppujen toiminnasta ja rakenteesta, josta jatketaan laitteen käytettävyyteen ja muiden lämmitysmenetelmien vertailuun. Sähköisten ominaisuuksien tarkastelussa pohditaan ilmalämpöpumppujen vaikutusta suomalaiseen sähköverkkoon muun muassa yleissähkötekniikan, taloudellisuuden ja energiatehokkuuden sekä häiriöiden kannalta. Tämä tutkielma rajoittuu pientaloihin, ja niihin asennettuihin ilma-ilmalämpöpumppuihin. Työn loppupäätelmänä on, että ilmalämpöpumppujen käytöstä ei juuri aiheudu vaikutuksia suomalaiseen sähköverkkoon. Suurimmat ilmalämpöpumppujen käytöstä syntyvät seuraukset kohdistuvat sähköverkkoyhtiöihin, joihin ilmalämpöpumput aiheuttavat taloudellisia menetyksiä. Suuret ja tulevaisuudessa kasvavat ilmalämpöpumppumäärät aiheuttavat sähköntuotantoon lisätehontarvetta huippukuorman aikaan. Toisaalta välitehoalueella tehontarve sekä energiankulutus pienenevät. Sähköverkoissa ei ole toistaiseksi havaittu ilmalämpöpumpuista johtuvia häiriöitä.