Mild and severe wear of steels and cast irons in sliding abrasion

This paper presents the results obtained in pin-on-disk test apparatus using glass and alumina as abrasive materials, showing the rates and mechanisms of abrasive wear of 1070 and 52100 steels, and ductile and white cast irons. The test conditions were selected in order to obtain wear rates that correspond to mild and severe abrasion, using different metal hardness-to-abrasive hardness ratios(H/H(A)) and 0.2 or 0.06 mm abrasive grains. The use of bulk Vickers hardness, instead of microhardness, allows a better description of the different abrasion regions. Under severe abrasion, the microcutting mechanism of wear prevailed together with friction coefficients larger than 0.4. On the other hand, when relatively soft abrasives are tested, indentation of abrasive particles followed by its fragmentation, and a creation of a thin deformed layer were the main damage mechanisms, with the friction coefficient lying below 0.4. The abrasive particle size under mild regime is able to change the wear rates in an order of magnitude. (C) 2009 Elsevier B.V. All rights reserved.

Emissions from the premixed combustion of gasified polyethylene

An investigation was conducted on pollutants emitted from steady-state, steady-flow gasification and combustion of polyethylene (PE) in a two-stage furnace. The polymer, in pulverized form, was first pyrolyzed at 1000 degrees C, and subsequently, its gaseous pyrolyzates were burned, upon mixing with air at high temperatures (900-1100 degrees C). The motivation for this indirect type of burning PE was to attain nominally premixed combustion of the pyrolyzate gases with air, thereby achieving lower pollutant emissions than those emanating from the direct burning of the solid PE polymer. This work assessed the effluents of the two-stage furnace and examined the effects of the combustion temperature, as well as the polymer feed rate and the associated fuel/air equivalence ratio (0.3 < phi < 1.4). It was found that, whereas the yield of pyrolysis gas decreased with an increasing polymer feed rate, its composition was nearly independent of the feed rate. CO2 emissions peaked at an equivalence ratio near unity, while the CO emissions increased with an increasing equivalence ratio. The total light volatile hydrocarbon and semivolatile polycyclic aromatic hydrocarbon (PAH) emissions of combustion increased with an increasing equivalence ratio. The generated particulates were mostly submicrometer in size. Overall, PAH and soot emissions from this indirect burning of PE were an order of magnitude lower than corresponding emissions from the direct burning of the solid polymer, obtained previously in this laboratory using identical sampling and analytical techniques. Because pyrolysis of this polymer requires a nominal heat input that amounts to only a diminutive fraction of the heat released during its combustion, implementation of this technique is deemed advantageous.

Photodegradation of Thermodegraded Polypropylene/High-Impact Polystyrene Blends: Mechanical Properties

The influence of the addition of high-impact polystyrene (HIPS) on polypropylene (PP) photodegradation was studied with blends obtained by extrusion with and without styrene-butadiene-styrene (SBS) copolymer (10 wt % with respect to the dispersed phase). The concentrations of HIPS ranged from 10 to 30 wt %. The blends and pure materials were exposed for periods of up to 15 weeks of UV irradiation; their mechanical properties (tensile and impact), fracture surface, and melt flow indices were monitored. After 3 weeks of UV exposure, all of the materials presented mechanical properties of the same order of magnitude. However, for times of exposure greater than 3 weeks, an increasing concentration of HIPS resulted in a better photostability of PP. These results were explained in light of morphological observations. This increase of photostability was even greater when SBS was added to the blends. It was more difficult to measure the melt flow index of the binary PP/HIPS blends than that of PP for low concentrations of HIPS; this was most likely due to energy transfer between the blend domains during photodegradation. This phenomenon was not observed for the ternary blends. (C) 2010 Wiley Periodicals, Inc. J Appl Polym Sci 120: 770-779, 2011

Abrasion and corrosion resistance of new Ni-based coating deposited by HVOF thermal spray process

Coatings based on NiCrAlC intermetallic based alloy were applied on AISI 316L stainless steel substrates using a high velocity oxygen fuel torch. The influence of the spray parameters on friction and abrasive wear resistance were investigated using an instrumented rubber wheel abrasion test, able to measure the friction forces. The corrosion behaviour of the coatings were studied with electrochemical techniques and compared with the corrosion resistance of the substrate material. Specimens prepared using lower O(2)/C(3)H(8) ratios showed smaller porosity values. The abrasion wear rate of the NiCrAlC coatings was much smaller than that described in the literature for bulk as cast materials with similar composition and one order of magnitude higher than bulk cast and heat treated (aged) NiCrAlC alloy. All coatings showed higher corrosion resistance than the AISI 316L substrate in HCl (5%) aqueous solution at 40 degrees C.

Experimental Measurement of Water Diffusion through Fine Aggregate Mixtures

The water diffusion attributable to concentration gradients is among the main mechanisms of water transport into the asphalt mixture. The transport of small molecules through polymeric materials is a very complex process, and no single model provides a complete explanation because of the small molecule`s complex internal structure. The objective of this study was to experimentally determine the diffusion of water in different fine aggregate mixtures (FAM) using simple gravimetric sorption measurements. For the purposes of measuring the diffusivity of water, FAMs were regarded as a representative homogenous volume of the hot-mix asphalt (HMA). Fick`s second law is generally used to model diffusion driven by concentration gradients in different materials. The concept of the dual mode diffusion was investigated for FAM cylindrical samples. Although FAM samples have three components (asphalt binder, aggregates, and air voids), the dual mode was an attempt to represent the diffusion process by only two stages that occur simultaneously: (1) the water molecules are completely mobile, and (2) the water molecules are partially mobile. The combination of three asphalt binders and two aggregates selected from the Strategic Highway Research Program`s (SHRP) Materials Reference Library (MRL) were evaluated at room temperature [23.9 degrees C (75 degrees F)] and at 37.8 degrees C (100 degrees F). The results show that moisture uptake and diffusivity of water through FAM is dependent on the type of aggregate and asphalt binder. At room temperature, the rank order of diffusivity and moisture uptake for the three binders was the same regardless of the type of aggregate. However, this rank order changed at higher temperatures, suggesting that at elevated temperatures different binders may be undergoing a different level of change in the free volume. DOI: 10.1061/(ASCE)MT.1943-5533.0000190. (C) 2011 American Society of Civil Engineers.

Assessing the effects of early silvicultural management on long-term site productivity of fast-growing eucalypt plantations: the Brazilian experience

Eucalyptus is the dominant and most productive planted forest in Brazil, covering around 3.4 million ha for the production of charcoal, pulp, sawtimber, timber plates, wood foils, plywood and for building purposes. At the early establishment of the forest plantations, during the second half of the 1960s, the eucalypt yield was 10 m(3) ha(-1) y(-1). Now, as a result of investments in research and technology, the average productivity is 38 m3 ha(-1) y(-1). The productivity restrictions are related to the following environmental factors, in order of importance: water deficits > nutrient deficiency > soil depth and strength. The clonal forests have been fundamental in sites with larger water and nutrient restrictions, where they out-perform those established from traditional seed-based planting stock. When the environmental limitations are small the productivities of plantations based on clones or seeds appear to be similar. In the long term there are risks to sustainability, because of the low fertility and low reserves of primary minerals in the soils, which are, commonly, loamy and clayey oxisols and ultisols. Usually, a decline of soil quality is caused by management that does not conserve soil and site resources, damages soil physical and chemical characteristics, and insufficient or unbalanced fertiliser management. The problem is more serious when fast-growing genotypes are planted, which have a high nutrient demand and uptake capacity, and therefore high nutrient output through harvesting. The need to mobilise less soil by providing more cover and protection, reduce the nutrient and organic matter losses, preserve crucial physical properties as permeability ( root growth, infiltration and aeration), improve weed control and reduce costs has led to a progressive increase in the use of minimum cultivation practices during the last 20 years, which has been accepted as a good alternative to keep or increase site quality in the long term. In this paper we provide a synthesis and critical appraisal of the research results and practical implications of early silvicultural management on long-term site productivity of fast-growing eucalypt plantations arising from the Brazilian context.

Validation of a root water uptake model to estimate transpiration constraints

Experimental results obtained from a greenhouse trial with common bean (Phaseolus vulgaris L) plants performed to test model hypotheses regarding the onset of limiting hydraulic conditions and the shape of the transpiration reduction curve in the falling rate phase are presented. According to these hypotheses based on simulations with an upscaled single-root model, the matric flux potential at the onset of limiting hydraulic conditions is as a function of root length density and potential transpiration rate, while the relative transpiration in the falling rate phase equals the relative matric flux potential. Transpiration of bean plants in water stressed pots with four different soils was determined daily by weighing and compared to values obtained from non-stressed pots. This procedure allowed determining the onset of the falling rate phase and corresponding soil hydraulic conditions. At the onset of the falling rate phase, the value of matric flux potential M(I) showed to differ in order of magnitude from the model predicted value for three out of four soils. This difference between model and experiment can be explained by the heterogeneity of the root distribution which is not considered by the model. An empirical factor to deal with this heterogeneity should be included in the model to improve predictions. Comparing the predictions of relative transpiration in the falling rate phase using a linear shape with water content, pressure head or matric flux potential, the matric flux potential based reduction function, in agreement with the hypothesis, showed the best performance, while the pressure head based equation resulted in the highest deviations between observed and predicted values of relative transpiration rates. (C) 2010 Elsevier B.V. All rights reserved.

Micronutrient dynamics in the forest biomass in succession stages of a seasonal deciduous forest, RS, Brazil

There is a great need of research to assess the behavior of micronutrients in natural forests of southern Brazil. Do to this need, the objective of this work was to study the levels and amounts of micronutrients in forest above ground biomass of the forest, in a comparative way, in two secondary succession stages (SSS) in a Seasonal Deciduous Forest in Rio Grande do Sul, Brazil. The SSS had enjoyed 35 and 55 years of regeneration since the end of agricultural use, respectively for initial secondary forest (ISF) and late secondary forest (LSF). The above-ground biomass was collected and separated into vegetative strata and these in fractions, thereafter chemically analyzed for the levels of B, Fe, Zn, Mn and Cu. Leaf fractions of arboreal, shrubs and herbaceous strata showed the highest levels for most nutrients. Only the levels of iron and manganese were higher in the bark fraction, for both sucession stages. In the LSF, the herbaceous stratum also showed high levels of Fe. The average levels of micronutrients showed differences between the two sucession stages only in relation to Fe and Mn, with higher levels in LSF biomass. The amount of nutrients stored was always higher in LSF, because of the largest biomass and the higher levels of Fe and Mn in the biomass of this SSS. The quantitative order of nutrient storage in biomass was Fe> Mn> Zn> B> Cu.

Cubebin and derivatives as inhibitors of mitochondrial complex I. Proposed interaction with subunit B8

The effects on mitochondrial respiration and complex I NADH oxidase activity of cubebin and derivatives were evaluated. The compounds inhibited the state 3 glutamate/malate-supported respiration of hamster liver mitochondria with IC50 values ranging from 12.16 to 83.96M. NADH oxidase reaction was evaluated in submitochondrial particles. The compounds also inhibited this activity, showing the same order of potency observed for effects on state 3 respiration, as well as a tendency towards a non-competitive type of inhibition (KI values ranging from 0.62 to 16.1M). A potential binding mode of these compounds with complex I subunit B8, assessed by docking calculations, is proposed.

Inflorescence and floral development of Dahlstedtia species (Leguminosae: Papilionoideae: Millettieae)

Inflorescence and floral development of two tropical legume trees, Dahlstedtia pinnata and Dahlstedlia pentaphylla, occurring in the Atlantic Forest of south-eastern and southern Brazil, were investigated and compared with other papilionoids. Few studies have been made of floral development in tribe Millettieae, and this paper is intended to fill that gap in our knowledge. Dahlstedtia species have an unusual inflorescence type among legumes, the pseudoraceme, which comprises axillary units of three or more flowers, each with a subtending bract. Each flower exhibits a pair of opposite bractcoles. The order of flower initiation is acropetal; inception of the floral organs is as follows: sepals (5), petals (5), carpel (1) plus outer stamens (5) and finally inner stamens (5). Organ initiation in sepal, petal and inner stamen whorls is unidirectional; the carpel cleft is adaxial. The vexillum originates from a tubular-shaped primordium in mid-development and is larger than other petals at maturity, covering the keels. The filament tube develops later after initiation of inner-stamen primordia. Floral development in Dahlstedtia is almost always similar to other papilionoids, especially species of Phaseoleae and Sophoreae. But one important difference is the precocious ovule initiation (open carpel with ovules) in Dahlstedtia, the third citation of this phenomenon for papilionoids. No suppression, organ loss or anomalies occur in the order of primordia initiation or structure. Infra-generic differences in the first stages of ontogeny are rare; however, different species of Dahlstedtia are distinguished by the differing distribution pattern of secretory cavities in the flower. (C) 2009 Elsevier GmbH. All rights reserved.

Improved treatment of vulvovaginal candidiasis with fluconazole plus probiotic Lactobacillus rhamnosus GR-1 and Lactobacillus reuteri RC-14

To determine the ability of probiotic lactobacilli to improve the treatment of vulvovaginal candidiasis (VVC) using a randomized, double-blind and placebo-controlled trial. Fifty-five women diagnosed with VVC by vaginal discharge positive for Candida spp. (according to culture method) associated with at least one of the symptoms (itching and burning vaginal feeling, dyspareunia and dysuria), were treated with single dose of fluconazole (150 mg) supplemented every morning for the following 4 weeks with two placebo or two probiotic capsules (containing Lactobacillus rhamnosus GR-1 and Lactobacillus reuteri RC-14). At 4 weeks, the probiotic treated group showed significantly less vaginal discharge associated with any of the above mentioned symptoms (10.3%vs 34.6%; P = 0.03) and lower presence of yeast detected by culture (10.3%vs 38.5%; P = 0.014). This study has shown that probiotic lactobacilli can increase the effectiveness of an anti-fungal pharmaceutical agent in curing disease. This novel finding of probiotic lactobacilli augmenting the cure rate of yeast vaginitis, not only offers an alternative approach to a highly prevalent condition that adversely affects the quality of life of women around the world, but also raises the question of how this combination works.

Improved cure of bacterial vaginosis with single dose of tinidazole (2 g), Lactobacillus rhamnosus GR-1, and Lactobacillus reuteri RC-14: a randomized, double-blind, placebo-controlled trial

Bacterial vaginosis (BV) is the most prevalent vaginal infection worldwide and is characterized by depletion of the indigenous lactobacilli. Antimicrobial therapy is often ineffective. We hypothesized that probiotic Lactobacillus rhamnosus GR-1 and Lactobacillus reuteri RC-14 might provide an adjunct to antimicrobial treatment and improve cure rates. Sixty-four Brazilian women diagnosed with BV were randomly assigned to receive a single dose of tinidazole (2 g) supplemented with either 2 placebo capsules or 2 capsules containing L. rhamnosus GR-1 and L. reuteri RC-14 every morning for the following 4 weeks. At the end of treatment (day 28), the probiotic group had a significantly higher cure rate of BV (87.5%) than the placebo group (50.0%) (p = 0.001). In addition, according to the Gram-stain Nugent score, more women were assessed with ""normal`` vaginal microbiota in the probiotic group (75.0% vs. 34.4% in the placebo group; p = 0.011). This study shows that probiotic lactobacilli can provide benefits to women being treated with antibiotics for an infectious condition.

On the validity of the shrinking core model in noncatalytic gas solid reaction

By using a matched asymptotic expansion technique, the shrinking core model (SCM) used in non-catalytic gas solid reactions with general kinetic expression is rigorously justified in this paper as a special case of the homogeneous model when the reaction rate is much faster than that of diffusion. The time-pendent velocity of the moving reacted-unreacted interface is found to be proportional to the gas flux at that interface for all geometries of solid particles, and the thickness order of the reaction zone and also the degree of chemical reaction at the interface is discussed in this paper.

What are the economic prospects of developing aquaculture in Queensland to supply the low price white fillet market? Lessons from the US channel catfish industry

The farming of channel catfish (Ictalurus punctatus) is the largest (by volume and value) and most successful (in terms of market impact) aquaculture industry in the United States of America. Farmed channel catfish is the most consumed (in terms of volume per capita) fish fillet in the U.S. market. Within Australia, it has long been suggested by researchers and industry that silver perch (Bidyanus bidyanus) and possibly other endemic teraponid species possess similar biological attributes for aquaculture as channel catfish and may have the potential to generate a similar industry. The current teraponid industry in Australia, however, shows very little resemblance to the catfish industry, either in production style or market philosophy. A well established budget framework from the literature on U.S. channel catfish farming has been adapted for cost and climate conditions of the Burdekin region, Queensland, Australia. Breakeven prices for the hypothetical teraponid farms were found to be up to 50% higher than those published for catfish farms however were much lower than those reported for silver perch production in Australia using current, endemic styles of production. The breakeven prices for the hypothetical teraponid farms were most sensitive (in order of significance) to feed prices, production rates, interest rates, fingerling prices and electricity prices. At equivalent feed costs the costs of production between the hypothetical catfish farms in the Mississippi, U.S. and the hypothetical teraponid farms in the Burdekin, Australia were remarkably similar. The cost of feeds suitable for teraponid production in Australia are currently around double that of catfish feeds in the U.S. Issues currently hindering the development of a large scale teraponid industry in Australia are discussed.

Catalytic activities and coking characteristics of oxides-supported Ni catalysts for CH4 reforming with carbon dioxide

Catalytic activities and deactivation characteristics of oxides-supported nickel catalysts for the reaction of methane reforming with carbon dioxide were investigated. The dynamic carbon deposition on various nickel catalysts was also studied by a thermogravimetric method. Among the catalysts prepared, Ni/La2O3, Ni/alpha-Al2O3, Ni/SiO2, and Ni/CeO2 showed very high CH4 and CO2 conversions and moderate deactivation whereas Ni/MgO and Ni/TiO2 had lower conversions when the Ni reduction was conducted at 500 degrees C. When Ni/MgO catalyst was reduced at 800 degrees C, it exhibited not only comparable conversions of CH4 and CO2 with other active catalysts but also much longer period of stability without deactivation. The amount of carbon deposited in Ni-based catalysts varied depending on the nature of support and followed the order of Ni/La2O3 > Ni/alpha-Al2O3 > Ni/SiO2 > Ni/MgO > Ni/CeO2 at 700 degrees C. The carbons formed on the catalyst surface showed different structural and chemical properties, and these in turn affected the catalytic activity of the catalysts.