Water-soluble complexes of an acrylamide copolymer and ionic liquids for inhibiting shale hydration

Here, we report water-soluble complexes of an acrylamide copolymer and ionic liquids for inhibiting shale hydration. The copolymer, denoted as PAAT, was synthesised via copolymerisation of acrylamide (AM), acrylic acid (AA) and N,N-diallyl-4-methylbenzenesulfonamide (TCDAP), and the ionic liquids used were 3-methyl imidazoliumcation-based tetrafluoroborates. X-ray diffraction showed that compared with commonly used KCl, the water-soluble complex of PAAT with 2 wt% ionic liquid 1-methyl-3-H-imidazolium tetrafluoroborate (HmimBF4) could remarkably reduce the d-spacing of sodium montmorillonite in water from 19.24 to 13.16 Å and effectively inhibit clay swelling. It was also found that the PAAT-HmimBF4 complex with 2 wt% HmimBF4 could retain 75% of the shale indentation hardness and increase the anti-swelling ratio to 85%. 13C NMR revealed that there existed interactions between PAAT and HmimBF4. Moreover, the thermal stability of the PAAT-HmimBF4 complex is superior to PAAT, suggesting that this water-soluble complex can be used to inhibit clay and shale hydration in high-temperature oil and gas wells.

On the Bauschinger effect in dual phase steel at high levels of strain

The effect of volume fraction and hardness of martensite on the Bauschinger effect in Dual Phase (DP) steel was investigated for strain levels close to those observed in automotive stamping. Five different grades of DP steel were produced by controlled heat treatment allowing the examination of the Bauschinger effect for three different volume fractions of martensite and three levels of martensite hardness. Compression-tension and shear reversal tests were performed to examine the Bauschinger effect at high levels of forming strain. Good correlation between the shear reversal and the compression-tension test was observed suggesting that for DP steel, shear stress strain data, converted to equivalent stress-strain, may be applied directly to characterize kinematic hardening behavior for numerical simulations. Permanent softening was observed following strain reversal and increased with martensite volume fraction and pre-strain level. While the Bauschinger ratio saturates at 3% pre-strain, the Bauschinger strain increases linearly with forming strain without showing saturation. This suggests that to model material behavior accurately in forming processes involving complex loading paths and high levels of strain, test data generated at high strain is required.

Chip formation mechanism and machinability of wrought duplex stainless steel alloys

This paper investigates the chip formation mechanism and machinability of two-phase materials, such as, wrought duplex stainless steel alloys SAF 2205 and SAF 2507. SEM and optical microscopic details of the frozen cutting zone and chips revealed that the harder austenite phase dissipates in the advancement of the cutting tool, being effectively squeezed out of the softer ferrite phase. Microhardness profiles reveal correlation in hardness from the workpiece material transitioning to the chip. The tool wear (TiAIN + TiN coated solid carbide twist drill) and machining forces were investigated. Tool wear, was dominantly due to the adhesion process which developed from built-up edge formation, is highly detrimental to the flank face. Flute damage was also observed as a major issue in the drilling of duplex alloys leading to premature tool failure. Duplex 2507 shows higher sensitivity to cutting speed during machining and strain hardening at higher velocity and less machinability due to presence of higher percentage of Ni, Mo and Cr.

Inulin and maltodextrin can replace fat in baked savoury legume snacks

A baked yellow split pea cracker was developed with fat replacement (0%, 25%, 50%, 75% and 100%) using inulin, hydroxypropyl methylcellulose and maltodextrin. Effects of fat replacement on physical (water activity, moisture content, colour and hardness), nutritional properties and consumer acceptance (nine-point hedonic rating) of snacks were investigated. Water activity (0.15-0.32) and moisture (1.28-3.16%) readings were consistent, and products were considered shelf stable. High levels of fat replacement (100%) were detrimental to snack colour and hardness. Snacks with 75% fat replacement using inulin and maltodextrin received similar mean overall acceptability scores (6.40 ± 1.36 and 6.26 ± 1.37, respectively) to the control and a similar commercial product. These snacks were eligible to claim that they were a 'good source' of protein (requirement; ≥10 g per serve) and an 'excellent source' of dietary fibre (requirement; ≥7 g per serve) while providing 'reduced' fat content (≤25% than reference food) based on the Australian Food Standards Code.

Sensitivity of the final properties of tailored hot stamping components to the process and material parameters

The final mechanical properties of hot stamped components are affected by many process and material parameters due to the multidisciplinary nature of this thermal-mechanical-metallurgical process. The phase transformation, which depends on the temperature field and history, determines the final microstructure and consequently the final mechanical properties. Tailored hot stamping parts - where the cooling rates are locally chosen to achieve structures with graded properties - has been increasingly adopted in the automotive industry. In this case, the robustness of final part properties is more critical than in the conventional hot stamping parts, where the part is fully quenched. In this study, a wide range of input parameters in a generalized hot stamping model have been investigated, examining the effect on the temperature history and resulting final material properties. A generic thermo-mechanical finite element model of hot stamping was created and a modified phase transformation model, based on Scheil's additive principle, has been applied. The comparison between modeling and experiments shows that the modified phase transformation model coupled with the incubation time provides higher accuracy on the simulation of transformation kinetics history. The robustness of four conditions relevant to tailored hot stamping was investigated: heated tooling (with low and high tool conductance), air cooling, and conventional hot stamping. The results show the high robustness of the conventional hot stamping compared to tailored hot stamping, with respect to the stamped component's final material properties (i.e. phase fraction and hardness). Furthermore, tailored hot stamping showed higher robustness when low conductivity tools are used relative to high conductivity tools.

Microstructure and mechanical properties of wrought and additive manufactured Ti-6Al-4V cylindrical bars

Titanium alloys are widely used in various engineering design application due to its superior material properties. The traditional manufacturing of titanium products is always difficult, time consuming, high material wastage and manufacturing costs. Selective laser melting (SLM), an additive manufacturing technology has widely gained attention due to its capability to produce near net shape components with less production time. In this technical paper,microstructure,chemical composition,tensile properties and hardness are studied for the wrought and additive manufactured SLM cylindrical bar. Microstructure,mechanical properties and hardness were studied in both the longitudinal and transverse directions of the bar to study the effect of orientation. It was found that additive manufactured bar have higher yield strength, ultimate tensile strength and hardness than the wrought bar. For both conventional and SLM test samples, the yield strength, ultimate tensile strength and hardness was found to be high in the transverse direction. The difference in the properties can be attributed to the difference in microstructure as a result of processing conditions. The tensile fracture area was quantified by careful examination of the fracture surfaces in the scanning electron microscope.

Effect of B4C, TiB2 and ZrSiO4 ceramic particles on mechanical properties of aluminium matrix composites: Experimental investigation and predictive modelling

This paper focuses on the influence of processing temperature and inclusion of micron-sized B4C, TiB2 and ZrSiO4 on the mechanical performance of aluminium matrix composites fabricated through stir casting. The ceramic/aluminium composite could withstand greater external loads, due to interfacial ceramic/aluminium bonding effect on the movement of grain and twin boundaries. Based on experimental results, the tensile strength and hardness of ceramic reinforced composite are significantly increased. The maximum improvement is achieved through adding ZrSiO4 and TiB2, which has led to 52% and 125% increase in tensile strength and hardness, respectively. To predict the effect of incorporating ceramic reinforcements on the mechanical properties of composites, experimental data of mechanical tests are used to create 3 models named Levenberg-Marquardt Algorithm (LMA) neural networks. The results show that the LMA- neural networks models have a high level of accuracy in the prediction of mechanical properties for ceramic reinforced-aluminium matrix composites.

Nanoscale variation in energy dissipation in austenitic shape memory alloys in ultimate loading cycles

Wavy behaviours of hysteresis energy variation in nanoscale bulk of thermomechanical austenitic NiTi shape memory alloy are reported in ultimate nanoindentation loading cycles. One sharp and two spherical tips were used while two loading-unloading rates were applied. For comparison, another austenitic copper-based shape memory alloy, CuAlNi shape memory alloy, and a metal with no phase transition, elastoplastic Cu, were investigated. In shape memory alloys, the hysteresis energy variation ultimately undergoes a linear decrease with internal wavy fluctuations and no stabilisation was observed. The internal energy fluctuation in these alloys was found dissimilar depending on the loading-unloading rate and the indentation tip geometry. In contrast, there was an absence of both overall and internal variations in hysteresis energy for Cu after the second loading cycle. The underlying physics of these variations is discussed and found to be attributed to both the created dislocations and ratcheting thermal-mechanical behaviour of the phase-transformed volume in shape memory alloys.

A preliminary study on machinability of super austenitic stainless steel

Stainless steel is the most widely used alloys of steel. The reputed variety of stainless steel having customised material properties as per the design requirements is Duplex Stainless Steel and Austenitic Stainless Steel. The Austenite Stainless Steel alloy has been developed further to be Super Austenitic Stainless Steel (SASS) by increasing the percentage of the alloying elements to form the half or more than the half of the material composition. SASS (Grade-AL-6XN) is an alloy steel containing high percentages of nickel (24%), molybdenum (6%) and chromium (21%). The chemical elements offer high degrees of corrosion resistance, toughness and stability in a large range of hostile environments like petroleum, marine and food processing industries. SASS is often used as a commercially viable substitute to high cost non-ferrous or non-metallic metals. The ability to machine steel effectively and efficiently is of utmost importance in the current competitive market. This paper is an attempt to evaluate the machinability of SASS which has been a classified material so far with very limited research conducted on it. Understanding the machinability of this alloy would assist in the effective forming of this material by metal cutting. The novelty of research associated with this is paper is reasonable taking into consideration the unknowns involved in machining SASS. The experimental design consists of conducting eight milling trials at combination of two different feed rates, 0.1 and 0.15 mm/tooth; cutting speeds, 100 and 150 m/min; Depth of Cut (DoC), 2 and 3 mm and coolant on for all the trials. The cutting tool has two inserts and therefore has two cutting edges. The trial sample is mounted on a dynamometer (type 9257B) to measure the cutting forces during the trials. The cutting force data obtained is later analyzed using DynaWare supplied by Kistler. The machined sample is subjected to surface roughness (Ra) measurement using a 3D optical surface profilometer (Alicona Infinite Focus). A comprehensive metallography process consisting of mounting, polishing and etching was conducted on a before and after machined sample in order to make a comparative analysis of the microstructural changes due to machining. The microstructural images were capture using a digital microscope. The microhardness test were conducted on a Vickers scale (Hv) using a Vickers microhardness tester. Initial bulk hardness testing conducted on the material show that the alloy is having a hardness of 83.4 HRb. This study expects an increase in hardness mostly due to work hardening may be due to phase transformation. The results obtained from the cutting trials are analyzed in order to judge the machinability of the material. Some of the criteria used for machinability evaluation are cutting force analysis, surface texture analysis, metallographic analysis and microhardness analysis. The methodology followed in each aspect of the investigation is similar to and inspired by similar research conducted on other materials. However, the novelty of this research is the investigation of various aspects of machinability and drawing comparisons between each other while attempting to justify each result obtained to the microstructural changes observed which influence the behaviour of the alloy. Due to the limited scope of the paper, machinability criteria such as chip morphology, Metal Removal Rate (MRR) and tool wear are not included in this paper. All aspects are then compared and the optimum machining parameters are justified with a scope for future investigations

Precipitation processes in Al-Cu-Mg-Sn and Al-Cu-Mg-Sn-Ag

Microalloying trace elements into aluminum alloys have been shown to improve mechanical properties by altering the precipitation process. Here, trace amounts of Sn and (Sn + Ag) have been added to Al-1.1Cu-1.7Mg (at.%) and the effects have been investigated by a combination of hardness testing and transmission electron microscopy (TEM). Hardness testing shows that the addition of Sn increases the hardness throughout the ageing process, and in combination with Ag, further increases the hardness and shortens the time to reach the peak hardness. The increase in hardness via Sn microalloying is attributed to the homogeneous distribution of S phase (Al2CuMg) precipitates. In the alloy microalloyed with both Sn and Ag, the microstructure is dominated by homogeneously distributed Ω phase (Al2Cu) precipitates in the peak strengthened condition. Given that neither spherical β-Sn precipitates, nor any other obvious nucleation sites for the Ω phase precipitates were observed using TEM, the mechanism for development of such homogeneous precipitation remains to be determined.

Estudos eletroquímicos de permeação de hidrogênio e determinação de concentrações críticas de hidrogênio em um aço de alta dureza

Estudou-se, através do método eletroquímico de permeação, a difusão de hidrogênio no ferro puro e no aço DIN 90MnV8. Observou-se nestes materiais, que o coeficiente aparente de difusão de hidrogênio diminui no decorrer dos transientes de permeação, tendo-se interpretado este comportamento como causado pela presença de armadilhas reversíveis. Deduziu-se, para transientes de permeação obtidos entre dois estados estacionários de difusão, que a variação da concentração de hidrogênio preso a armadilhas reversiveis é dada por: Delta Ca = Na. In [(1+alfa)1/2 dividido por (1+beta)1/2], alfa = K.Co/p beta=K.Cl/p sendo Na a densidade de armadilhas; k e p, os parâmetros de captura e de liberação de uma armadilha e Co e Cl, a concentrasão inicial e final de H. Mediu-se, no ferro recozido, um coeficiente médio de difusão de hidrogênio de 6,4.10-5 cm²/s. A deformação com 50% de trabalho a frio no ferro reduz este valor em aproximadamente uma ordem de grandeza. Verificou-se no aço DIN 90MnV8 que o coeficiente de difusão de hidrogênio aumenta com o aumento dn temperatura de revenimento após a têmpera, atingindo o valor máximo de 7,0.10-6 cm²/s no aço esferoidizado. A dependência térmica do coeficiente de difusão no aço DIN 90MnV8 esferoidizado pode ser expressa por: D = 1,95 (+0,49) exp (-30,43kJ/mol.R.T.) (cm²/s) e neste mesmo aço temperado e revenido com 55RC de dureza por : D=0,29 (+- 0,05 ) exp (-28,47kJ/mol.R.T.) ( cm²/s). Uma nova metodolagia fractomecânica foi introduzida, a qual permite a determinação da cnncentração crítica de hidrogênio necessária para provocar o avanço de uma trinca estacionária. Observou-se no aço DIN 9OMnV8, que a concentração crítica de hidrogênio diminui com o aumento da dureza do aço e é menor quando um valor maior de KI é aplicado. O modo de fratura apresentado Por este aço revelou ser independente da concentração de hidrogênio e do valor de KI, sendo função unicamente de sua dureza.

Novas fases amorfas de carbono produzidas por irradiação iônica de filmes de C/sub 60/, [alfa]-C e [alfa]-C:H

Neste trabalho estuda-se a formação de novas fases de carbono amorfo através da irradiação iônica de filmes de fulereno, a-C e a-C:H polimérico. Os efeitos da irradiação iônica na modificação das propriedades ópticas e mecânicas dos filmes de carbono irradiados são analisados de forma correlacionada com as alterações estruturais a nivel atômico. O estudo envolve tanto a análise dos danos induzidos no fulereno pela irradiação iônica a baixas fluências, correspondendo a baixas densidades de energia depositada, quanto a investigação das propriedades físico-químicas das fases amorfas obtidas após irradiações dos filmes de fulereno, a-C e a-C:H com altas densidades de energia depositada. As propriedades ópticas, mecânicas e estruturais das amostras são analisadas através de técnicas de espectroscopia Raman e infravermelho, espectrofotometria UV-VIS-NIR, microscopias ópticas e de força atômica, nanoindentação e técnicas de análise por feixe de íons, tais como retroespalhamento Rutherford e análises por reação nuclear. As irradiações produzem profundas modificações nas amostras de fulereno, a-C e a-C:H, e por conseqüência significativas alterações em suas propriedades ópticas e mecânicas. Após máximas fluências de irradiação fases amorfas rígidas (com dureza de 14 e 17 GPa) e com baixos gaps ópticos (0,2 e 0,5 eV) são formadas. Estas estruturas não usuais correspondem a arranjos atômicos com 90 a 100% de estados sp2. Em geral fases sp2 são planares e apresentam baixa dureza, como predito pelo modelo de “cluster”. Entretanto, os resultados experimentais mostram que as propriedades elásticas das novas fases formadas são alcançadas através da criação de uma estrutura sp2 tridimensional. A indução de altas distorções angulares, através da irradiação iônica, possibilita a formação de anéis de carbono não hexagonais, tais como pentágonos e heptágonos, permitindo assim a curvatura da estrutura. Utilizando um modelo de contagem de vínculos é feita uma análise comparativa entre a topologia (estrutura geométrica) de ligações C-sp2 e as propriedades nanomecânicas. São comparados os efeitos de estruturas sp2 planares e tridimensionais (aleatórias) no processo de contagem de vínculos e, conseqüentemente, nas propriedades elásticas de cada sistema. Os resultados mostram que as boas propriedades mecânicas das novas fases de carbono formadas seguem as predições do modelo de vínculos para uma rede atômica sp2 tridimensional. A formação de uma fase amorfa dura e 100% sp2 representa uma importante conquista na procura de novas estruturas rígidas de carbono. A síntese da estrutura desordenada sp2 tridimensional e vinculada aqui apresentada é bastante incomum na literatura. O presente trabalho mostra que o processo de não-equilíbrio de deposição de energia durante a irradiação iônica permite a formação de distorções angulares nas ligações sp2-C, possibilitando a criação de estruturas grafíticas tridimensionais.

Desenvolvimento de elastômeros termoplásticos a partir de SBR epoxidada e polipropileno

Os elastômeros termoplásticos vulcanizados (TPVs) na sua maioria constituídos por borrachas apolares (EPDM, NR) e poliolefinas (PP, PE), apresentam a vantagem de serem processáveis como termoplásticos e serem facilmente reciclados. No entanto, apresentam desvantagens no que se refere à sua baixa resistência a óleos, combustíveis e graxas em relação à borracha termofixa. Este trabalho, teve como objetivo estudar a obtenção de TPVs com propriedades mecânicas adequadas e resistência a óleos e solventes orgânicos, a partir da borracha comercial SBR 1502 parcialmente epoxidada. Esta, por ter a estrutura química de sua cadeia principal modificada pela introdução de grupos epóxidos, deve apresentar melhor resistência a óleos e solventes. Os TPVs foram obtidos em misturador fechado acoplado a um reômetro Haake, na temperatura de 1800C e velocidade de rotor de 75 rpm, vulcanizados dinamicamente com o sistema Bismaleimida/peróxido de dicumila. Foram caracterizados quanto às suas propriedades mecânicas por medidas tensão-deformação, medidas mecânicas dinâmicas, inchamento em ciclohexano, THF e óleo IRM 903, dureza. A morfologia foi determinada por microscopia eletrônica de varredura, MEV. Foram analisados os fatores que influenciam as propriedades dos TPVs, tais como composição (relação PP/SBR), teor de BMI, grau de epoxidação da borracha, uso de agente compatibilizante. O TPV na composição PP/SBR 40/60, esta epoxidada em 40 mol % e contendo o agente compatibilizante Vestenamer adicionado na forma de blenda (borracha/agente compatibilizante) apresentou a melhor resposta em termos de tensão-deformação na ruptura. Os TPVs com a SBR epoxidada em 70% apresentaram melhor resistência a óleo e solventes. Os fatores, potencialmente, capazes de influenciar a dureza dos TPVs também foram avaliados. Neste particular, verificou-se que o tipo de poliolefina, bem como o uso de plastificante são os fatores que mais influenciam a dureza dos TPVs.

A Comparati ve Study of Mechanical and Tribological Properties of AISI-304 and AISI-316 Submitted to Glow Discharge Nitriding

Mechanical and tribological properties of AISI 304 and AISI 316 stainless steels submitted to glow discharge ion nitriding are reported. The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C. Treatment at 300 °C produced expanded austenite (γN) in both steels. Increasing the temperature, the phases γ′-Fe4N and ε- Fe2+xN were present and the latter is the major phase for AISI 304. At 500 °C, the CrN phase was also identified in both steels. Hardnesses of about 13-14 GPa at near surface regions were obtained in both steels. Moreover, AISI 316 nitrided at 500 °C has the deepest hard layer. Tribological tests showed that wear can be reduced by up to a factor of six after the nitriding processes, even for a working temperature of 300 °C. The profiles during and after nanoscratch tests did not reveal significant differences after nitriding processes in both steels.

A Comparative Study of Mechanical and Tribological Properties of AISI-304 and AISI-316 Submitted to Glow Discharge Nitriding

Mechanical and tribological properties of AISI 304 and AISI 316 stainless steels submitted to glow discharge ion nitriding are reported. The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C. Treatment at 300 °C produced expanded austenite (γN) in both steels. Increasing the temperature, the phases γ′-Fe4N and ε- Fe2+xN were present and the latter is the major phase for AISI 304. At 500 °C, the CrN phase was also identified in both steels. Hardnesses of about 13-14 GPa at near surface regions were obtained in both steels. Moreover, AISI 316 nitrided at 500 °C has the deepest hard layer. Tribological tests showed that wear can be reduced by up to a factor of six after the nitriding processes, even for a working temperature of 300 °C. The profiles during and after nanoscratch tests did not reveal significant differences after nitriding processes in both steels.