Thermal studies of D.C. traction motors

This paper describes a thorough thermal study on a fleet of DC traction motors which were found to suffer from overheating after 3 years of full operation. Overheating of these traction motors is attributed partly because of the higher than expected number of starts and stops between train terminals. Another probable cause of overheating is the design of the traction motor and/or its control strategy. According to the motor manufacturer, a current shunt is permanently connected across the motor field winding. Hence, some of the armature current is bypassed into the current shunt. The motor then runs above its rated speed in the field weakening mode. In this study, a finite difference model has been developed to simulate the temperature profile at different parts inside the traction motor. In order to validate the simulation result, an empty vehicle loaded with drums of water was also used to simulate the full pay-load of a light rail vehicle experimentally. The authors report that the simulation results agree reasonably well with experimental data, and it is likely that the armature of the traction motor will run cooler if its field shunt is disconnected at low speeds

Assessment of heat-related health impacts in Brisbane, Australia : comparison of different heatwave definitions

Background: There is no global definition of a heatwave because local acclimatisation and adaptation influence the impact of extreme heat. Even at a local level there can be multiple heatwave definitions, based on varying temperature levels or time periods. We investigated the relationship between heatwaves and health outcomes using ten different heatwave definitions in Brisbane, Australia. ---------- Methodology/Principal Findings: We used daily data on climate, air pollution, and emergency hospital admissions in Brisbane between January 1996 and December 2005; and mortality between January 1996 and November 2004. Case-crossover analyses were used to assess the relationship between each of the ten heatwave definitions and health outcomes. During heatwaves there was a statistically significant increase in emergency hospital admissions for all ten definitions, with odds ratios ranging from 1.03 to 1.18. A statistically significant increase in the odds ratios of mortality was also found for eight definitions. The size of the heat-related impact varied between definitions.---------- Conclusions/Significance Even a small change in the heatwave definition had an appreciable effect on the estimated health impact. It is important to identify an appropriate definition of heatwave locally and to understand its health effects in order to develop appropriate public health intervention strategies to prevent and mitigate the impact of heatwaves.

Embracing diversity : empowering preservice teachers for teaching gifted and talented students

This study investigated preservice teachers’ perceptions for teaching and sustaining gifted and talented students while developing, modifying and implementing activities to cater for the diverse learner. Participants were surveyed at the end of a gifted and talented education program on their perceptions to differentiate the curriculum for meeting the needs of the student (n=22). SPSS data analysis with the five-part Likert scale indicated these preservice teachers agreed or strongly agreed they had developed skills in curriculum planning (91%) with well-designed activities (96%), and lesson preparation skills (96%). They also claimed they were enthusiastic for teaching (91%) and understanding of school practices and policies (96%). However, 46% agreed they had knowledge of syllabus documents with 50% claiming an ability to provide written feedback on student’s learning. Furthermore, nearly two-thirds suggested they had educational language from the syllabus and effective student management strategies. Preservice teachers require more direction on how to cater for diversity and begin creating sustainable societies by building knowledge from direct GAT experiences. Designing diagnostic surveys associated with university coursework can be used to determine further development for specific preservice teacher development in GAT education. Preservice teachers need to create opportunities for students to realise their potential by involving cognitive challenges through a differentiated curriculum. Differentiation requires modification of four primary areas of curriculum development (Maker, 1975) content (what we teach), process (how we teach), product (what we expect the students to do or show) and learning environment (where we teach/our class culture). Ashman and Elkins (2009) and Glasson (2008) emphasise the need for preservice teachers, teachers and other professionals to be able to identify what gifted and talented (GAT) students know and how they learn in relation to effective teaching. Glasson (2008) recommends that educators keep up to date with practices in pedagogy, support, monitoring and profiling of GAT students to create an environment conducive to achieving. Oral feedback is one method to communicate to learners about their progress but has advantages and disadvantages for some students. Oral feedback provides immediate information to the student on progress and performance (Ashman & Elkins, 2009). However, preservice teachers must have clear understandings of key concepts to assist the GAT student. Implementing teaching strategies to engage innovate and extend students is valuable to the preservice teacher in focusing on GAT student learning in the classroom (Killen, 2007). Practical teaching strategies (Harris & Hemming, 2008; Tomlinson et al., 1994) facilitate diverse ways for assisting GAT students to achieve learning outcomes. Such strategies include activities to enhance creativity, co-operative learning and problem-solving activities (Chessman, 2005; NSW Department of Education and Training, 2004; Taylor & Milton, 2006) for GAT students to develop a sense of identity, belonging and self esteem towards becoming an autonomous learner. Preservice teachers need to understand that GAT students learn in a different way and therefore should be assessed differently. Assessment can be through diverse options to demonstrate the student’s competence, demonstrate their understanding of the material in a way that highlights their natural abilities (Glasson, 2008; Mack, 2008). Preservice teachers often are unprepared to assess students understanding but this may be overcome with teacher education training promoting effective communication and collaboration in the classroom, including the provision of a variety of assessment strategies to improve teaching and learning (Callahan et al., 2003; Tomlinson et al., 1994). It is also critical that preservice teachers have enthusiasm for teaching to demonstrate inclusion, involvement and the excitement to communicate to GAT students in the learning process (Baum, 2002). Evaluating and reflecting on teaching practices must be part of a preservice teacher’s repertoire for GAT education. Evaluating teaching practices can assist to further enhance student learning (Mayer, 2008). Evaluation gauges the success or otherwise of specific activities and teaching in general (Mayer, 2008), and ensures that preservice teachers and teachers are well prepared and maintain their commitment to their students and the community. Long and Harris (1999) advocate that reflective practices assist teachers in creating improvements in educational practices. Reflective practices help preservice teachers and teachers to improve their ability to pursue improved learning outcomes and professional growth (Long & Harris, 1999). Context This study is set at a small regional campus of a large university in Queensland. As a way to address departmental policies and the need to prepare preservice teachers for engaging a diverse range of learners (see Queensland College of Teachers, Professional Standards for Teachers, 2006), preservice teachers at this campus completed four elective units within their Bachelor of Education (primary) degree. The electives include: 1. Middle years students and schools 2. Teaching strategies for engaging learners 3. Teaching students with learning difficulties, and 4. Middle-years curriculum, pedagogy and assessment. In the university-based component of this unit, preservice teachers engaged in learning about middle years students and schools, and gained knowledge of government policies pertaining to GAT students. Further explored within in this unit was the importance of: collaboration between teachers, parents/carers and school personnel in supporting middle years GAT students; incorporating challenging learning experiences that promoted higher order thinking and problem solving skills; real world learning experiences for students and; the alignment and design of curriculum, pedagogy and assessment that is relevant to the students development, interests and needs. The participants were third-year Bachelor of Education (primary) preservice teachers who were completing an elective unit as part of the middle years of schooling learning with a focus on GAT students. They were assigned one student from a local school. In the six subsequent ninety minute weekly lessons, the preservice teachers were responsible for designing learning activities that would engage and extend the GAT students. Furthermore, preservice teachers made decisions about suitable pedagogical approaches and designed the assessment task to align with the curriculum and the developmental needs of their middle years GAT student. This research aims to describe preservice teachers’ perceptions of their education for teaching gifted and talented students.

Transforming people, place, and technology : towards re-creative city

This session is titled TRANSFORM! Opportunities and Challenges of Digital Content for Creative Economy. Some of the key concepts for this session include: 1. City / Economy 2. Creativity 3. Digital content 4. Transformation All of us would agree that these terms describe pertinent characteristics of contemporary world, the epithet of which is the ‘network era.’ I was thinking about what I would like to discuss here and what you, leading experts in divergent fields, would be interested to hear about. As the keynote for this session and as one of the first speakers for the entire conference, I see my role as an initiator for imagination, the wilder the better, posing questions rather than answers. Also given the session title Transform!, I wish to change this slightly to Transforming People, Place, and Technology: Towards Re-­creative City in an attempt to take us away a little from the usual image depicted by the given topic. Instead, I intend to sketch a more holistic picture by reflecting on and extrapolating the four key concepts from the urban informatics point of view. To do so, I use ‘city’ as the primary guiding concept for my talk rather than probably more expected ‘digital media’ or ‘creative economy.’ You may wonder what I mean by re-­creative city. I will explain this in time by looking at the key concepts from these four respective angles: 1. Living city 2. Creative city 3. Re-­‐creative city 4. Opportunities and Challenges to arrive at a speculative yet probable image of the city that we may aspire to transform our current cities into. First let us start by considering the ‘living city.’

Social clubs and social capital : the effect of electronic gaming machines in disadvantaged regions on the creation or destruction of community resilience

The role of particular third sector organisations, Social Clubs, in supporting gambling through the use of EGMs in venues presents as a difficult social issue. Social Clubs gain revenue from gambling activities; but also contribute to social well-being through the provision of services to communities. The revenues derived from gambling in specific geographic locales has been seen by government as a way to increase economic development particularly in deprived areas. However there are also concerns about accessibility of low-income citizens to Electronic Gaming Machines (EGMS) and the high level of gambling overall in these deprived areas. We argue that social capital can be viewed as a guard against deleterious effects of unconstrained use of EGM gambling in communities. However, it is contended that social capital may also be destroyed by gambling activity if commercial business actors are able to use EGMs without community obligations to service provision. This paper examines access to gambling through EGMs and its relationship to social capital and the consequent effect on community resilience, via an Australian case study. The results highlight the potential two-way relationship between gambling and volunteering, such that volunteering (and social capital more generally) may help protect against problems of gambling, but also that volunteering as an activity may be damaged by increased gambling activity. This suggests that, regardless of the direction of causation, it is necessary to build up social capital via volunteering and other social capital activities in areas where EGMS are concentrated. The study concludes that Social Clubs using EGMs to derive funds are uniquely positioned within the community to develop programs that foster social capital creation and build community resilience in deprived areas.

Dynamics of pattern writing and erasure in photorefractive lithium niobate for data storage applications

The present rate of technological advance continues to place significant demands on data storage devices. The sheer amount of digital data being generated each year along with consumer expectations, fuels these demands. At present, most digital data is stored magnetically, in the form of hard disk drives or on magnetic tape. The increase in areal density (AD) of magnetic hard disk drives over the past 50 years has been of the order of 100 million times, and current devices are storing data at ADs of the order of hundreds of gigabits per square inch. However, it has been known for some time that the progress in this form of data storage is approaching fundamental limits. The main limitation relates to the lower size limit that an individual bit can have for stable storage. Various techniques for overcoming these fundamental limits are currently the focus of considerable research effort. Most attempt to improve current data storage methods, or modify these slightly for higher density storage. Alternatively, three dimensional optical data storage is a promising field for the information storage needs of the future, offering very high density, high speed memory. There are two ways in which data may be recorded in a three dimensional optical medium; either bit-by-bit (similar in principle to an optical disc medium such as CD or DVD) or by using pages of bit data. Bit-by-bit techniques for three dimensional storage offer high density but are inherently slow due to the serial nature of data access. Page-based techniques, where a two-dimensional page of data bits is written in one write operation, can offer significantly higher data rates, due to their parallel nature. Holographic Data Storage (HDS) is one such page-oriented optical memory technique. This field of research has been active for several decades, but with few commercial products presently available. Another page-oriented optical memory technique involves recording pages of data as phase masks in a photorefractive medium. A photorefractive material is one by which the refractive index can be modified by light of the appropriate wavelength and intensity, and this property can be used to store information in these materials. In phase mask storage, two dimensional pages of data are recorded into a photorefractive crystal, as refractive index changes in the medium. A low-intensity readout beam propagating through the medium will have its intensity profile modified by these refractive index changes and a CCD camera can be used to monitor the readout beam, and thus read the stored data. The main aim of this research was to investigate data storage using phase masks in the photorefractive crystal, lithium niobate (LiNbO3). Firstly the experimental methods for storing the two dimensional pages of data (a set of vertical stripes of varying lengths) in the medium are presented. The laser beam used for writing, whose intensity profile is modified by an amplitudemask which contains a pattern of the information to be stored, illuminates the lithium niobate crystal and the photorefractive effect causes the patterns to be stored as refractive index changes in the medium. These patterns are read out non-destructively using a low intensity probe beam and a CCD camera. A common complication of information storage in photorefractive crystals is the issue of destructive readout. This is a problem particularly for holographic data storage, where the readout beam should be at the same wavelength as the beam used for writing. Since the charge carriers in the medium are still sensitive to the read light field, the readout beam erases the stored information. A method to avoid this is by using thermal fixing. Here the photorefractive medium is heated to temperatures above 150�C; this process forms an ionic grating in the medium. This ionic grating is insensitive to the readout beam and therefore the information is not erased during readout. A non-contact method for determining temperature change in a lithium niobate crystal is presented in this thesis. The temperature-dependent birefringent properties of the medium cause intensity oscillations to be observed for a beam propagating through the medium during a change in temperature. It is shown that each oscillation corresponds to a particular temperature change, and by counting the number of oscillations observed, the temperature change of the medium can be deduced. The presented technique for measuring temperature change could easily be applied to a situation where thermal fixing of data in a photorefractive medium is required. Furthermore, by using an expanded beam and monitoring the intensity oscillations over a wide region, it is shown that the temperature in various locations of the crystal can be monitored simultaneously. This technique could be used to deduce temperature gradients in the medium. It is shown that the three dimensional nature of the recording medium causes interesting degradation effects to occur when the patterns are written for a longer-than-optimal time. This degradation results in the splitting of the vertical stripes in the data pattern, and for long writing exposure times this process can result in the complete deterioration of the information in the medium. It is shown in that simply by using incoherent illumination, the original pattern can be recovered from the degraded state. The reason for the recovery is that the refractive index changes causing the degradation are of a smaller magnitude since they are induced by the write field components scattered from the written structures. During incoherent erasure, the lower magnitude refractive index changes are neutralised first, allowing the original pattern to be recovered. The degradation process is shown to be reversed during the recovery process, and a simple relationship is found relating the time at which particular features appear during degradation and recovery. A further outcome of this work is that the minimum stripe width of 30 ìm is required for accurate storage and recovery of the information in the medium, any size smaller than this results in incomplete recovery. The degradation and recovery process could be applied to an application in image scrambling or cryptography for optical information storage. A two dimensional numerical model based on the finite-difference beam propagation method (FD-BPM) is presented and used to gain insight into the pattern storage process. The model shows that the degradation of the patterns is due to the complicated path taken by the write beam as it propagates through the crystal, and in particular the scattering of this beam from the induced refractive index structures in the medium. The model indicates that the highest quality pattern storage would be achieved with a thin 0.5 mm medium; however this type of medium would also remove the degradation property of the patterns and the subsequent recovery process. To overcome the simplistic treatment of the refractive index change in the FD-BPM model, a fully three dimensional photorefractive model developed by Devaux is presented. This model shows significant insight into the pattern storage, particularly for the degradation and recovery process, and confirms the theory that the recovery of the degraded patterns is possible since the refractive index changes responsible for the degradation are of a smaller magnitude. Finally, detailed analysis of the pattern formation and degradation dynamics for periodic patterns of various periodicities is presented. It is shown that stripe widths in the write beam of greater than 150 ìm result in the formation of different types of refractive index changes, compared with the stripes of smaller widths. As a result, it is shown that the pattern storage method discussed in this thesis has an upper feature size limit of 150 ìm, for accurate and reliable pattern storage.

Alkaline hydrothermal treatment of titanate nanostructures

Since its initial proposal in 1998, alkaline hydrothermal processing has rapidly become an established technology for the production of titanate nanostructures. This simple, highly reproducible process has gained a strong research following since its conception. However, complete understanding and elucidation of nanostructure phase and formation have not yet been achieved. Without fully understanding phase, formation, and other important competing effects of the synthesis parameters on the final structure, the maximum potential of these nanostructures cannot be obtained. Therefore this study examined the influence of synthesis parameters on the formation of titanate nanostructures produced by alkaline hydrothermal treatment. The parameters included alkaline concentration, hydrothermal temperature, the precursor material‘s crystallite size and also the phase of the titanium dioxide precursor (TiO2, or titania). The nanostructure‘s phase and morphology was analysed using X-ray diffraction (XRD), Raman spectroscopy and transmission electron microscopy. X-ray photoelectron spectroscopy (XPS), dynamic light scattering (non-invasive backscattering), nitrogen sorption, and Rietveld analysis were used to determine phase, for particle sizing, surface area determinations, and establishing phase concentrations, respectively. This project rigorously examined the effect of alkaline concentration and hydrothermal temperature on three commercially sourced and two self-prepared TiO2 powders. These precursors consisted of both pure- or mixed-phase anatase and rutile polymorphs, and were selected to cover a range of phase concentrations and crystallite sizes. Typically, these precursors were treated with 5–10 M sodium hydroxide (NaOH) solutions at temperatures between 100–220 °C. Both nanotube and nanoribbon morphologies could be produced depending on the combination of these hydrothermal conditions. Both titania and titanate phases are comprised of TiO6 units which are assembled in different combinations. The arrangement of these atoms affects the binding energy between the Ti–O bonds. Raman spectroscopy and XPS were therefore employed in a preliminary study of phase determination for these materials. The change in binding energy from a titania to a titanate binding energy was investigated in this study, and the transformation of titania precursor into nanotubes and titanate nanoribbons was directly observed by these methods. Evaluation of the Raman and XPS results indicated a strengthening in the binding energies of both the Ti (2p3/2) and O (1s) bands which correlated to an increase in strength and decrease in resolution of the characteristic nanotube doublet observed between 320 and 220 cm.1 in the Raman spectra of these products. The effect of phase and crystallite size on nanotube formation was examined over a series of temperatures (100.200 �‹C in 20 �‹C increments) at a set alkaline concentration (7.5 M NaOH). These parameters were investigated by employing both pure- and mixed- phase precursors of anatase and rutile. This study indicated that both the crystallite size and phase affect nanotube formation, with rutile requiring a greater driving force (essentially �\harsher. hydrothermal conditions) than anatase to form nanotubes, where larger crystallites forms of the precursor also appeared to impede nanotube formation slightly. These parameters were further examined in later studies. The influence of alkaline concentration and hydrothermal temperature were systematically examined for the transformation of Degussa P25 into nanotubes and nanoribbons, and exact conditions for nanostructure synthesis were determined. Correlation of these data sets resulted in the construction of a morphological phase diagram, which is an effective reference for nanostructure formation. This morphological phase diagram effectively provides a .recipe book�e for the formation of titanate nanostructures. Morphological phase diagrams were also constructed for larger, near phase-pure anatase and rutile precursors, to further investigate the influence of hydrothermal reaction parameters on the formation of titanate nanotubes and nanoribbons. The effects of alkaline concentration, hydrothermal temperature, crystallite phase and size are observed when the three morphological phase diagrams are compared. Through the analysis of these results it was determined that alkaline concentration and hydrothermal temperature affect nanotube and nanoribbon formation independently through a complex relationship, where nanotubes are primarily affected by temperature, whilst nanoribbons are strongly influenced by alkaline concentration. Crystallite size and phase also affected the nanostructure formation. Smaller precursor crystallites formed nanostructures at reduced hydrothermal temperature, and rutile displayed a slower rate of precursor consumption compared to anatase, with incomplete conversion observed for most hydrothermal conditions. The incomplete conversion of rutile into nanotubes was examined in detail in the final study. This study selectively examined the kinetics of precursor dissolution in order to understand why rutile incompletely converted. This was achieved by selecting a single hydrothermal condition (9 M NaOH, 160 °C) where nanotubes are known to form from both anatase and rutile, where the synthesis was quenched after 2, 4, 8, 16 and 32 hours. The influence of precursor phase on nanostructure formation was explicitly determined to be due to different dissolution kinetics; where anatase exhibited zero-order dissolution and rutile second-order. This difference in kinetic order cannot be simply explained by the variation in crystallite size, as the inherent surface areas of the two precursors were determined to have first-order relationships with time. Therefore, the crystallite size (and inherent surface area) does not affect the overall kinetic order of dissolution; rather, it determines the rate of reaction. Finally, nanostructure formation was found to be controlled by the availability of dissolved titanium (Ti4+) species in solution, which is mediated by the dissolution kinetics of the precursor.

Characterisation of the tritrophic interactions between tobacco yellow dwarf virus, its vector and host-plants

Tobacco yellow dwarf virus (TbYDV, family Geminiviridae, genus Mastrevirus) is an economically important pathogen causing summer death and yellow dwarf disease in bean (Phaseolus vulgaris L.) and tobacco (Nicotiana tabacum L.), respectively. Prior to the commencement of this project, little was known about the epidemiology of TbYDV, its vector and host-plant range. As a result, disease control strategies have been restricted to regular poorly timed insecticide applications which are largely ineffective, environmentally hazardous and expensive. In an effort to address this problem, this PhD project was carried out in order to better understand the epidemiology of TbYDV, to identify its host-plant and vectors as well as to characterise the population dynamics and feeding physiology of the main insect vector and other possible vectors. The host-plants and possible leafhopper vectors of TbYDV were assessed over three consecutive growing seasons at seven field sites in the Ovens Valley, Northeastern Victoria, in commercial tobacco and bean growing properties. Leafhoppers and plants were collected and tested for the presence of TbYDV by PCR. Using sweep nets, twenty-three leafhopper species were identified at the seven sites with Orosius orientalis the predominant leafhopper. Of the 23 leafhopper species screened for TbYDV, only Orosius orientalis and Anzygina zealandica tested positive. Forty-two different plant species were also identified at the seven sites and tested. Of these, TbYDV was only detected in four dicotyledonous species, Amaranthus retroflexus, Phaseolus vulgaris, Nicotiana tabacum and Raphanus raphanistrum. Using a quadrat survey, the temporal distribution and diversity of vegetation at four of the field sites was monitored in order to assess the presence of, and changes in, potential host-plants for the leafhopper vector(s) and the virus. These surveys showed that plant composition and the climatic conditions at each site were the major influences on vector numbers, virus presence and the subsequent occurrence of tobacco yellow dwarf and bean summer death diseases. Forty-two plant species were identified from all sites and it was found that sites with the lowest incidence of disease had the highest proportion of monocotyledonous plants that are non hosts for both vector and the virus. In contrast, the sites with the highest disease incidence had more host-plant species for both vector and virus, and experienced higher temperatures and less rainfall. It is likely that these climatic conditions forced the leafhopper to move into the irrigated commercial tobacco and bean crop resulting in disease. In an attempt to understand leafhopper species diversity and abundance, in and around the field borders of commercially grown tobacco crops, leafhoppers were collected from four field sites using three different sampling techniques, namely pan trap, sticky trap and sweep net. Over 51000 leafhopper samples were collected, which comprised 57 species from 11 subfamilies and 19 tribes. Twentythree leafhopper species were recorded for the first time in Victoria in addition to several economically important pest species of crops other than tobacco and bean. The highest number and greatest diversity of leafhoppers were collected in yellow pan traps follow by sticky trap and sweep nets. Orosius orientalis was found to be the most abundant leafhopper collected from all sites with greatest numbers of this leafhopper also caught using the yellow pan trap. Using the three sampling methods mentioned above, the seasonal distribution and population dynamics of O. orientalis was studied at four field sites over three successive growing seasons. The population dynamics of the leafhopper was characterised by trimodal peaks of activity, occurring in the spring and summer months. Although O. orientalis was present in large numbers early in the growing season (September-October), TbYDV was only detected in these leafhoppers between late November and the end of January. The peak in the detection of TbYDV in O. orientalis correlated with the observation of disease symptoms in tobacco and bean and was also associated with warmer temperatures and lower rainfall. To understand the feeding requirements of Orosius orientalis and to enable screening of potential control agents, a chemically-defined artificial diet (designated PT-07) and feeding system was developed. This novel diet formulation allowed survival for O. orientalis for up to 46 days including complete development from first instar through to adulthood. The effect of three selected plant derived proteins, cowpea trypsin inhibitor (CpTi), Galanthus nivalis agglutinin (GNA) and wheat germ agglutinin (WGA), on leafhopper survival and development was assessed. Both GNA and WGA were shown to reduce leafhopper survival and development significantly when incorporated at a 0.1% (w/v) concentration. In contrast, CpTi at the same concentration did not exhibit significant antimetabolic properties. Based on these results, GNA and WGA are potentially useful antimetabolic agents for expression in genetically modified crops to improve the management of O. orientalis, TbYDV and the other pathogens it vectors. Finally, an electrical penetration graph (EPG) was used to study the feeding behaviour of O. orientalis to provide insights into TbYDV acquisition and transmission. Waveforms representing different feeding activity were acquired by EPG from adult O. orientalis feeding on two plant species, Phaseolus vulgaris and Nicotiana tabacum and a simple sucrose-based artificial diet. Five waveforms (designated O1-O5) were observed when O. orientalis fed on P. vulgaris, while only four (O1-O4) and three (O1-O3) waveforms were observed during feeding on N. tabacum and the artificial diet, respectively. The mean duration of each waveform and the waveform type differed markedly depending on the food source. This is the first detailed study on the tritrophic interactions between TbYDV, its leafhopper vector, O. orientalis, and host-plants. The results of this research have provided important fundamental information which can be used to develop more effective control strategies not only for O. orientalis, but also for TbYDV and other pathogens vectored by the leafhopper.

An analysis of parliamentary questions raised by Opposition in the Uttar Pradesh (India) State Legislative Assembly

The use of parliamentary questions is the most popular and visible tool in the hands of the Opposition as a means to make government accountable. Their main purpose is to seek information or press for action. Contemporary parliamentary literature from the UK, Canada, and Australia, however, suggests that parliamentary questions have lost their effectiveness. The literature points out that Question Time in parliaments has become a battle ground between Ruling and Opposition parties in their fight to gain maximum political advantage. In this context, the effectiveness of parliamentary questions in the Indian state legislatures has not been investigated. The aim of this study, therefore, is to analyse the use, purpose and effectiveness of parliamentary questions in the State Legislative Assembly of Uttar Pradesh (India) to explore differences, if any, between Ruling and Opposition parties. In this study, 4023 parliamentary questions asked in the Uttar Pradesh State Legislative Assembly were analysed. The effectiveness of answers was also analysed qualitatively. The results show that half of the total members of the Assembly used this device, out of which 60% of the questions were asked by the Opposition party members. 31% of the questions from the Opposition were seeking information and 69% were pressing for action. The government provided the required information in 96% of the questions in the former category and took action in only 35% of the latter category. Furthermore, 60% of the questions raised by the Opposition were related to constituency matters and the remaining 40% were related to policy issues or public welfare. Comparing the data with the ruling party, the results indicate that the use,purpose and effectiveness of parliamentary questions were similar to that of the Opposition except some minor differences. Surprisingly, there was no evidence of any ‘Dorothy Dix’ questions. The study concludes parliamentary question is an effective device in the Indian state of Uttar Pradesh.

The 'Dirty Work' of the Lie

The panel "Duplicity/Complicity: Performing and Misperforming Lies" at PSi #15 in Croatia in July 2009 examined the half-truths, hidden assumptions and power relations embedded in every act of performance through an analysis of the way bodies, buildings, personae and communities perform and misperform lies. It was a collection of new academic voices from Australia and Croatia, intersecting and colliding and, at times, outright lying, with each other and with commentary from Alan Read. Inspired by this successful adventure in collaborative academic mis-performance, "The ‘Dirty Work’ of the Lie" takes the challenge set by the Prelude Panel at PSI #15 and subjects the ideas emerging from this panel to "friendly fire" in order to build a multi authored response to 'performance that lies', with reference to the work of A Chorus of Women, disabled artists Bill Shannon, Aaron Williamson and Kathryn Araneillo, US dance performer Ann Liv Young and US theatre and festival director Peter Sellars. In doing so, "The 'Dirty Work' of the Lie" provides a reflexive response to the duplicity inherent in the performances, and also in our own academic analyses. With Alan Read acting as interlocutor, each contributor will creatively respond to a paper presented by another, developing the key intersecting issues that emerged through the formation of the panel. These issues include impression management, self-belief and performers who are 'taken in by their own act', the dirty work of taking others in with an act, the guerrilla dimension of lying, the productivity of the lie, and questions of audience engagement and ethics. As a result, this new paper tests how the 'misperformance' of lies across different cultural sites, be it deliberate or accidental, can become a productive – and, indeed, politicised – aspect of cultural performance, betraying accepted attitudes, ideas and structures of authority and offering alternative visions. Through it’s distinctively multi vocal texture, "The 'Dirty Work' of the Lie" also interrogates the modes of analysis available to us, questioning the 'duplicity' in our reflecting, responding and listening to each other as well as the work.

Genetic analysis reveals two stocks of skipjack tuna (Katsuwonus pelamis) in the north western Indian Ocean

Skipjack (SJT) (Katsuwonus pelamis) is a medium sized, pelagic, highly dispersive tuna species that occurs widely across tropical and subtropical waters. SJT constitute the largest tuna fishery in the Indian Ocean, and are currently managed as a single stock. Patterns of genetic variation in a mtDNA gene and 6 microsatellite loci were examined to test for stock structure in the northwestern Indian Ocean. 324 individuals were sampled from five major fishing grounds around Sri Lanka, and single sites in the Maldive Islands and the Laccadive Islands. Phylogenetic reconstruction of mtDNA revealed two coexisting divergent clades in the region. AMOVA (Analysis of Molecular Variance) of mtDNA data revealed significant genetic differentiation among sites (ΦST = 0.2029, P < 0.0001), also supported by SAMOVA results. AMOVA of microsatellite data also showed significant differentiation among most sampled sites (FST = 0.0256, P<0.001) consistent with the mtDNA pattern. STRUCTURE analysis of the microsatellite data revealed two differentiated stocks. While the both two marker types examined identified two genetic groups, microsatellite analysis indicates that the sampled SJT are likely to represent individuals sourced from discrete breeding grounds that are mixed in feeding grounds in Sri Lankan waters.

Physical and functional interaction of the archaeal single-stranded DNA-binding protein SSB with RNA polymerase

Archaeal transcription utilizes a complex multisubunit RNA polymerase and the basal transcription factors TBP and TF(II)B, closely resembling its eukaryal counterpart. We have uncovered a tight physical and functional interaction between RNA polymerase and the single-stranded DNA-binding protein SSB in Sulfolobus solfataricus. SSB stimulates transcription from promoters in vitro under TBP-limiting conditions and supports transcription in the absence of TBP. SSB also rescues transcription from repression by reconstituted chromatin. We demonstrate the potential for promoter melting by SSB, suggesting a plausible basis for the stimulation of transcription. This stimulation requires both the single-stranded DNA-binding domain and the acidic C-terminal tail of the SSB. The tail forms a stable interaction with RNA polymerase. These data reveal an unexpected role for single-stranded DNA-binding proteins in transcription in archaea.

Full circle : the future of sustainable fashion manufacturing in New Zealand

Many fashion businesses in New Zealand have followed a global trend towards inexpensive off shore manufacturing. The transfer of the production of garments to overseas workers has had consequences for the wellbeing of local businesses, fashion designers and garment makers. The gradual decline of fashion manufacturing also appears to have resulted in a local fashion scene where many garments look the same in style, colour, fabric, cut and fit. The excitement of the past, where the majority of fashion designers established their own individuality through the cut and shape of the garments that they produced, may have been inadvertently lost in an effort to take advantage of cost savings achieved through mass production and manufacturing methods which are now largely unavailable in New Zealand. Consequently, a sustainable local fashion and manufacturing industry, with design integrity, seems further out of reach. This paper is focussed upon the thesis that the design and manufacture of a fashion garment, bearing in mind certain economic and practical restrictions at its inception, can contribute to a more sustainable fashion manufacturing industry in New Zealand.

Dryness : the aesthetic condition of landscape design in Australia

Despite having a band of greenness around the edge, Australia is fundamentally a dry country. Australian vegetation has developed a high range of mechanisms to cope with the dryness, but after 200 years of white settlement, Australians still have not really come to terms with the real dryness of their country, and still exploit European paradigms that attempted to transplant European aesthetic conditions, greenness, to the brown land of Australia. Australia is going through serious water shortages that are still and will continue with the Greenhouse effect, to become a major factor in the location and extent of urbanisation, and also Australia's carrying capacity. While such aesthetic concerns might seem ornamental, until the population changes its attitude to the real condition of the country, it will keep using water and operating unsustainably. The design of the public landscape, however, offers the opportunity to contribute to changing people's aesthetic perception of the country, which might in turn help to redirect their water use practices. This essay develops a language for discussion dryness based around the experiences of water. After having developed this sensibility it then discusses a range of different approaches that landscape design in Australia has used to try to develop geographically appropriate design languages, including the Bush Garden and the Mediterranean Garden. It then discusses four design projects, one from the 1970's, the other three from the last five years that demonstrate what such an aesthetic might look like.

Wavefront aberrations and the depth of focus of the human eye

The depth of focus (DOF) can be defined as the variation in image distance of a lens or an optical system which can be tolerated without incurring an objectionable lack of sharpness of focus. The DOF of the human eye serves a mechanism of blur tolerance. As long as the target image remains within the depth of focus in the image space, the eye will still perceive the image as being clear. A large DOF is especially important for presbyopic patients with partial or complete loss of accommodation (presbyopia), since this helps them to obtain an acceptable retinal image when viewing a target moving through a range of near to intermediate distances. The aim of this research was to investigate the DOF of the human eye and its association with the natural wavefront aberrations, and how higher order aberrations (HOAs) can be used to expand the DOF, in particular by inducing spherical aberrations ( 0 4 Z and 0 6 Z ). The depth of focus of the human eye can be measured using a variety of subjective and objective methods. Subjective measurements based on a Badal optical system have been widely adopted, through which the retinal image size can be kept constant. In such measurements, the subject.s tested eye is normally cyclopleged. Objective methods without the need of cycloplegia are also used, where the eye.s accommodative response is continuously monitored. Generally, the DOF measured by subjective methods are slightly larger than those measured objectively. In recent years, methods have also been developed to estimate DOF from retinal image quality metrics (IQMs) derived from the ocular wavefront aberrations. In such methods, the DOF is defined as the range of defocus error that degrades the retinal image quality calculated from the IQMs to a certain level of the possible maximum value. In this study, the effect of different amounts of HOAs on the DOF was theoretically evaluated by modelling and comparing the DOF of subjects from four different clinical groups, including young emmetropes (20 subjects), young myopes (19 subjects), presbyopes (32 subjects) and keratoconics (35 subjects). A novel IQM-based through-focus algorithm was developed to theoretically predict the DOF of subjects with their natural HOAs. Additional primary spherical aberration ( 0 4 Z ) was also induced in the wavefronts of myopes and presbyopes to simulate the effect of myopic refractive correction (e.g. LASIK) and presbyopic correction (e.g. progressive power IOL) on the subject.s DOF. Larger amounts of HOAs were found to lead to greater values of predicted DOF. The introduction of primary spherical aberration was found to provide moderate increase of DOF while slightly deteriorating the image quality at the same time. The predicted DOF was also affected by the IQMs and the threshold level adopted. We then investigated the influence of the chosen threshold level of the IQMs on the predicted DOF, and how it relates to the subjectively measured DOF. The subjective DOF was measured in a group of 17 normal subjects, and we used through-focus visual Strehl ratio based on optical transfer function (VSOTF) derived from their wavefront aberrations as the IQM to estimate the DOF. The results allowed comparison of the subjective DOF with the estimated DOF and determination of a threshold level for DOF estimation. Significant correlation was found between the subject.s estimated threshold level for the estimated DOF and HOA RMS (Pearson.s r=0.88, p<0.001). The linear correlation can be used to estimate the threshold level for each individual subject, subsequently leading to a method for estimating individual.s DOF from a single measurement of their wavefront aberrations. A subsequent study was conducted to investigate the DOF of keratoconic subjects. Significant increases of the level of HOAs, including spherical aberration, coma and trefoil, can be observed in keratoconic eyes. This population of subjects provides an opportunity to study the influence of these HOAs on DOF. It was also expected that the asymmetric aberrations (coma and trefoil) in the keratoconic eye could interact with defocus to cause regional blur of the target. A dual-Badal-channel optical system with a star-pattern target was used to measure the subjective DOF in 10 keratoconic eyes and compared to those from a group of 10 normal subjects. The DOF measured in keratoconic eyes was significantly larger than that in normal eyes. However there was not a strong correlation between the large amount of HOA RMS and DOF in keratoconic eyes. Among all HOA terms, spherical aberration was found to be the only HOA that helped to significantly increase the DOF in the studied keratoconic subjects. Through the first three studies, a comprehensive understanding of DOF and its association to the HOAs in the human eye had been achieved. An adaptive optics system was then designed and constructed. The system was capable of measuring and altering the wavefront aberrations in the subject.s eye and measuring the resulting DOF under the influence of different combination of HOAs. Using the AO system, we investigated the concept of extending the DOF through optimized combinations of 0 4 Z and 0 6 Z . Systematic introduction of a targeted amount of both 0 4 Z and 0 6 Z was found to significantly improve the DOF of healthy subjects. The use of wavefront combinations of 0 4 Z and 0 6 Z with opposite signs can further expand the DOF, rather than using 0 4 Z or 0 6 Z alone. The optimal wavefront combinations to expand the DOF were estimated using the ratio of increase in DOF and loss of retinal image quality defined by VSOTF. In the experiment, the optimal combinations of 0 4 Z and 0 6 Z were found to provide a better balance of DOF expansion and relatively smaller decreases in VA. Therefore, the optimal combinations of 0 4 Z and 0 6 Z provides a more efficient method to expand the DOF rather than 0 4 Z or 0 6 Z alone. This PhD research has shown that there is a positive correlation between the DOF and the eye.s wavefront aberrations. More aberrated eyes generally have a larger DOF. The association of DOF and the natural HOAs in normal subjects can be quantified, which allows the estimation of DOF directly from the ocular wavefront aberration. Among the Zernike HOA terms, spherical aberrations ( 0 4 Z and 0 6 Z ) were found to improve the DOF. Certain combinations of 0 4 Z and 0 6 Z provide a more effective method to expand DOF than using 0 4 Z or 0 6 Z alone, and this could be useful in the optimal design of presbyopic optical corrections such as multifocal contact lenses, intraocular lenses and laser corneal surgeries.