Estimation of gear tooth deflection by the finite element method

The finite element method (FEM) is used to determine for pitch-point, mid-point and tip loading, the deflection curve of a Image 1 diamentral pitch (DP) standard spur gear tooth corresponding to number of teeth of 14, 21, 26 and 34. In all these cases the deflection of the gear tooth at the point of loading obtained by FEM is in good agreement with the experimental value. The contraflexure in the deflection curve at the point of loading observed experimentally in the cases of pitch-point and mid-point loading, is predicted correctly by the FEM analysis.

Comment: Eigenvalue sensitivity method for optimal stabilisation of linear systems

In a letter RauA proposed a new method for designing statefeedback controllers using eigenvalue sensitivity matrices. However, there appears to be a conceptual mistake in the procedure, or else it is unduly restricted in its applicability. In particular the equation — BR~lBTK = A/.I, in which K is a positive-definite symmetric matrix.

A new culture method for lesser mealworm, Alphitobius diaperinus

A new culture method for lesser mealworm, Alphitobius diaperinus (Panzer), was developed to provide large numbers of adult lesser mealworms of approximately the same age for insecticide resistance testing. Culturing entailed allowing 100 adults to reproduce for 4 days in a wheat-based culture medium contained inside a plastic culture box, removing the adults from the medium, and then rearing their progeny to adulthood therein, in approximately 56 days at 32 degrees C and 55% RH. During their development, progeny were supplied water via apple slices at 0, 21 and 35 days, and a foam substrate in which to pupate, also at 35 days. During 2004-2005, adult lesser mealworms were collected from six broiler-house populations and then cultured with this method. Each population produced 4500 adults required to complete resistance testing with one insecticide within ten culture boxes, at an average of 798 adults per culture box.

A method for mapping the distribution and density of rabbits and other vertebrate pests in Australia

The European wild rabbit has been considered Australia’s worst vertebrate pest and yet little effort appears to have gone into producing maps of rabbit distribution and density. Mapping the distribution and density of pests is an important step in effective management. A map is essential for estimating the extent of damage caused and for efficiently planning and monitoring the success of pest control operations. This paper describes the use of soil type and point data to prepare a map showing the distribution and density of rabbits in Australia. The potential for the method to be used for mapping other vertebrate pests is explored. The approach used to prepare the map is based on that used for rabbits in Queensland (Berman et al. 1998). An index of rabbit density was determined using the number of Spanish rabbit fleas released per square kilometre for each Soil Map Unit (Atlas of Australian Soils). Spanish rabbit fleas were released into active rabbit warrens at 1606 sites in the early 1990s as an additional vector for myxoma virus and the locations of the releases were recorded using a Global Positioning System (GPS). Releases were predominantly in arid areas but some fleas were released in south east Queensland and the New England Tablelands of New South Wales. The map produced appears to reflect well the distribution and density of rabbits, at least in the areas where Spanish fleas were released. Rabbit pellet counts conducted in 2007 at 54 sites across an area of south east South Australia, south eastern Queensland, and parts of New South Wales (New England Tablelands and south west) in soil Map Units where Spanish fleas were released, provided a preliminary means to ground truth the map. There was a good relationship between mean pellet count score and the index of abundance for soil Map Units. Rabbit pellet counts may allow extension of the map into other parts of Australia where there were no Spanish rabbit fleas released and where there may be no other consistent information on rabbit location and density. The recent Equine Influenza outbreak provided a further test of the value of this mapping method. The distribution and density of domestic horses were mapped to provide estimates of the number of horses in various regions. These estimates were close to the actual numbers of horses subsequently determined from vaccination records and registrations. The soil Map Units are not simply soil types they contain information on landuse and vegetation and the soil classification is relatively localised. These properties make this mapping method useful, not only for rabbits, but also for other species that are not so dependent on soil type for survival.

Non-linear dynamic analysis of rotors by finite element method

Non-linear natural vibration characteristics and the dynamic response of hingeless and fully articulated rotors of rectangular cross-section are studied by using the finite element method. In the formulation of response problems, the global variables are augmented with appropriate additional variables, facilitating direct determination of sub-harmonic response. Numerical results are given showing the effect of the geometric non-linearity on the first three natural frequencies. Response analysis of typical rotors indicates a possibility of substantial sub-harmonic response especially in the fully articulated rotors widely adopted in helicopters.

An interactive method for engaging the public health workforce with evidence

Introduction Systematic review authors are increasingly directing their attention to not only ensuring the robust processes and methods of their syntheses, but also to facilitating the use of their reviews by public health decision-makers and practitioners. This latter activity is known by several terms including knowledge translation, for which one definition is a ‘dynamic and iterative process that includes synthesis, exchange and ethically sound application of knowledge’.1 Unfortunately—and despite good intentions—the successful translation of knowledge has at times been inhibited by the failure of reviews to meet the needs of decision-makers, and the limitations of the traditional avenues by which reviews are disseminated.2 Encouraging the utilization of reviews by the public health workforce is a complex challenge. An unsupportive culture within the workforce, a lack of experience in assessing evidence, the use of traditional academic language in communication and the lack of actionable messages can all act as barriers to successful knowledge translation.3 Improving communication through developing strategies that include summaries, podcasts, webinars and translational tools which target key decision-makers such as HealthEvidence.org should be considered by authors as promising actions to support the uptake of reviews into practice.4,5 Earlier work has also suggested that to better meet the research evidence needs of public health professionals, authors should aim to produce syntheses that are actionable, relevant and timely.2 Further, review authors must interact more with those who will, or could use their reviews; particularly when determining the scope and questions to which a review will be directed.2 Unfortunately, individual engagement, ideal for examining complex issues and addressing particular concerns, is often difficult, particularly when attempting to reach large groups where for efficiency purposes, the strategy tends to be didactic, ‘lecturing’ and therefore less likely to change attitudes or encourage higher order thinking.6 …

The Alpha-Method Direct Transcription In Path Constrained Dynamic Optimization

Numerically discretized dynamic optimization problems having active inequality and equality path constraints that along with the dynamics induce locally high index differential algebraic equations often cause the optimizer to fail in convergence or to produce degraded control solutions. In many applications, regularization of the numerically discretized problem in direct transcription schemes by perturbing the high index path constraints helps the optimizer to converge to usefulm control solutions. For complex engineering problems with many constraints it is often difficult to find effective nondegenerat perturbations that produce useful solutions in some neighborhood of the correct solution. In this paper we describe a numerical discretization that regularizes the numerically consistent discretized dynamics and does not perturb the path constraints. For all values of the regularization parameter the discretization remains numerically consistent with the dynamics and the path constraints specified in the, original problem. The regularization is quanti. able in terms of time step size in the mesh and the regularization parameter. For full regularized systems the scheme converges linearly in time step size.The method is illustrated with examples.

A rapid and sensitive method for the estimation of individual tRNA pools

A rapid and sensitive method is described to quantitatively compare tRNA pools for individual aminoacids in a single experiment. The procedure comprises of: (i) charging of total tRNA with a mixture of radiolabeled aminoacids, (ii) deacylation of the esterified tRNA with a volatile base and the recovery of the labeled aminoacid, (iii) derivatisation of the aminoacid with phenylisothiocyanate after mixing with excess of nonradioactive aminoacids, (iv) baseline separation of the phenylthiocarbamyl aminoacids by reverse phase high performance liquid chromatography monitored by A254nm and (v) quantitation of the radioactivity in individual aminoacid peaks. The radioactivity in the aminoacid peak corresponds to the quantity of the aminoacylated tRNA. The method has been successfully applied to quantitate the individual tRNA pools in the developing silk glands of Bombyx mori, a functionally adapted tissue which undergoes considerable variations in tRNA content. PSG, posterior silk gland; PITC, phenylisothiocyanate; DMAA, N,N-dimethyl-N-allylamine; APH, algal protein hydrolysate; ptc-, phenylthiocarbamyl; HPLC, high performance liquid chromatography.

Assessment of the underreporting rate of death cause data in Shandong province using capture-mark-recapture method [应用捕获再捕获方法评估山东省死因登记漏报率水平]

To evaluate the underreporting rate of death -cause data in Shandong province during 2012 to 2013 by capture -mark -recapture method and to provide the base for health strategy. Methods All counties were divided into 5 stratifications according the death rates of 2012, and 14 counties were selected, then 3 towns or streets were selected in each country, 10 villages or neighborhood committees were selected in each town （street）. The death data collected from security bureau and civil affairs bureau were compared with the reporting death data from the National Cause of Death Surveillance, and the underreporting rate was calculated. Results In present study, 6 929 death cases were collected, it was found that 1 556 cases were underreported. The death cases estimated by CMR method were 6 227 cases （95%CI: 7 593-7 651）, and the average underreporting rate was 23.15%. There were significantly differences between different stratifications （P<0.01）. The underreporting rate in 0-4 years old group was 56.93%, the male underreporting rate was 22.31% and the female underreporting rate was 24.09%. There was no significant difference between male and female groups （P>0.05）. Conclusion There is an obvious underreport in the cause of death surveillance of Shandong province, and the underreporting rates are different among the 5 stratifications. The underreporting rate is higher in 0-4 years old group, and the investigation of the death cause surveillance for young residents is not perfect in some countries. The investigation quality of the death cause surveillance should be improved, increasing the integrity of the report data and adjusting the mortalities in different stratifications for obtaining a accurate mortality in Shandong province.

Critical Evaluation of Determining Swelling Pressure by Swell-Load Method and Constant Volume Method

For any construction activity in expansive soils, determination of swelling pressure/heave is an essential step. Though many attempts have been made to develop laboratory procedures by using the laboratory one-dimensional oedometer to determine swelling pressure of expansive soils, they are reported to yield varying results. The main reason for these variations could be heterogeneous moisture distribution of the sample over its thickness. To overcome this variation the experimental procedure should be such that the soil gets fully saturated. Attempts were made to introduce vertical sand drains in addition to the top and bottom drains. In this study five and nine vertical sand drains were introduced to experimentally find out the variations in the swell and swelling pressure. The variations in the moisture content at middle, top, and bottom of the sample in the oedometer test are also reported. It is found that swell-load method is better as compared to zero-swell method. Further, five number of vertical sand drains are found to be sufficient to obtain uniform moisture content distribution.

New Modified Dipping Method Using 4-hexylresorcinol for Preventing Blackspot Formation in Prawns.

Industry acceptance of alternative sulphite treatments for preventing blackspot in prawns is limited. This study demonstrated that dipping prawns (Penaeus monodon and Fenneropenaeus merguiensis) in a less concentrated solution for longer times provides better control of blackspot formation than the recommended 2 minute dip in 50 mg/L 4-hexylresorcinol. Protection improved as modified dipping times and solution concentrations increased. Blackspot protection provided by most of the modified dip methods was more effective than a 1 minute dip in 1% sodium metabisulphite. The recommended 2 minute dip method should be limited to 125 kg when used on consecutive 25-kg batches of prawns. Yields increased by less than 10% even after 72-hour exposure in the modified dip. The new dipping method meets most international residue standards when applying the modified treatments evaluated.

Correlation Between The Stability Of Carbonates In Ternary Ln2o3-H2o-Co2 Hydrothermal Systems And Lanthanide Systematics

Phase diagrams for ternary Ln2O3-H2O-CO2 systems for the entire lanthanide series (except promethium) were studied at temperatures in the range 100–950 °C and pressures up to 3000 bar. The phase diagrams obtained for the heavier lanthanides are far more complex, with the appearance of a number of stable carbonate phases. New carbonates isolated from lanthanide systems (Ln ≡ Tm, Yb, Lu) include Ln6(OH)4(CO3)7, Ln4(OH)6-(CO3)3, Ln2O(OH)2CO3, Ln6O2(OH)8(CO3)3 and Ln12O7(OH)10(CO3)6. Stable carbonate phases common to all the lighter lanthanides are hexagonal LnOHCO3 and hexagonal Ln2O2CO3. Ln2(CO3)3• 3H2O is stable from samarium onwards and orthorhombic LnOHCO3 is stable from gadolinium onwards. On the basis of the appearance of stable carbonates, four different groups of lanthanides were established: lanthanum to neodymium, promethium to europium, terbium to erbium and thulium to lutetium. Gadolinium is the connecting element between groups II and III. This is in accordance with the tetrad classification for f transition elements.

Numerical modelling of deformation behaviour of red blood cells in microvessels using the coupled SPH-DEM method

This thesis developed an advanced computational model to investigate the motion and deformation properties of red blood cells in capillaries. The novel model is based on the meshfree particle methods and is capable of modelling the large deformation of red blood cells moving through blood vessels. The developed model was employed to simulate the deformation behaviour of healthy and malaria infected red blood cells as well as the motion of red blood cells in stenosed capillaries.

Evaluate traffic noise level based on traffic microsimulation combined with a refined classic noise prediction method

In this paper, a refined classic noise prediction method based on the VISSIM and FHWA noise prediction model is formulated to analyze the sound level contributed by traffic on the Nanjing Lukou airport connecting freeway before and after widening. The aim of this research is to (i) assess the traffic noise impact on the Nanjing University of Aeronautics and Astronautics (NUAA) campus before and after freeway widening, (ii) compare the prediction results with field data to test the accuracy of this method, (iii) analyze the relationship between traffic characteristics and sound level. The results indicate that the mean difference between model predictions and field measurements is acceptable. The traffic composition impact study indicates that buses (including mid-sized trucks) and heavy goods vehicles contribute a significant proportion of total noise power despite their low traffic volume. In addition, speed analysis offers an explanation for the minor differences in noise level across time periods. Future work will aim at reducing model error, by focusing on noise barrier analysis using the FEM/BEM method and modifying the vehicle noise emission equation by conducting field experimentation.

Intergenerational collaborative drawing: A research method for researching with/about young children

This paper focuses on the methodological effectiveness of intergenerational collaborative drawing (ICD). A group of eight researchers trialled this particular approach to drawing, most of them for the first time. Each researcher drew with young children, peers and tertiary students, with drawings created over a period of six months. The eight researchers came together in a 'community of scholars' approach to this project because of two shared interests: (i) issues of social justice, access and equity; and (ii) arts-based education research methods. The researchers were curious how ICD might methodologically support their respective research processes. As knowledge and theory about young children becomes more complex, researchers need responsive methodological tools to ask new questions and conduct rigorous, ethical research. This partial account describes how drawing together might perform methodologically. The data reported here draws from the detailed field notes, drawings and reflections of the researchers. Conclusions arise from the analysis of these reflections, with the authors suggesting ways in which ICD might benefit research with young children.