Atividades lúdicas e cultura em diferentes grupos etários e culturais

Não disponível

Concentração de tensões em peças e componentes estruturais - uma abordagem através do método dos elementos finitos

Any failure process that may occur in a part probably is located where the stress exceeded the level of resistance. When a part or component has a sharp change in geometry, such as slots, holes, grooves, bumps or other irregularities, there is an increased concentration of stress at a specific location of the part. The objective of this study is to determine the maximum stresses in structural parts and components using the equations of elasticity theory in conjunction with the stress concentration factor experiment and compare them with results obtained by finite element method

Análise estrutural de treliças espaciais no software Excel utilizando o médodo dos elementos finitos

The following paper means to develop a program to make structural analysis of space trusses. The program to be implemented was based on the concepts of the finite element method and used the programing resources of Visual Basic for Applications (VBA) for the Excel Software®. Being Excel® a software of easy access, low cost, capacity to make matrix calculations and with advanced resources of VBA programing, it is possible to develop an economic solution, efficient and precise for structural analysis of space trusses. Firstly is presented a finite elemento method and the space truss. Then is developed a few important algorithms to be used during the development of the program and also the use of a few resources of VBA. And to validate the quality, efficiency and precision of the results, these are compared with the established commercial software Ansys

Análise da atividade de peroxidases e polifenoloxidases em diferentes órgãos vegetativos de espécies arbóreas nativas de diferentes grupos sucessionais

As formações vegetais são altamente dinâmicas e dependem principalmente da taxa de crescimento das espécies vegetais, entretanto, esta está intimamente relacionada e suscetível a estresses abióticos, como elevada ou baixa radiação solar, temperaturas extremas, e bióticos, como taque de patógenos e de herbívoros, o que faz com que as plantas necessitem de um sistema de defesa altamente eficiente o qual consiste na atuação de compostos secundários, e de enzimas como por exemplo peroxidases e polifenoloxidases. A atividade das peroxidases constitui a mais importante via do sistema de defesa vegetal a patógenos no que se refere a cicatrização de ferimentos e à herbivoria, propiciando um aumento da lignificação nos tecidos lesados, o que aumenta a resistência dos mesmos, dificultando assim a ocorrência de novas lesões. Quanto às polifenoloxidases, também pertencentes ao grupo das oxidorredutases, são enzimas que também atuam diretamente na via de defesa das plantas ao ataque de patógenos e na cicatrização de ferimentos e processos de senescência. Por meio da extração e análise da atividade de Peroxidases e Polifenoloxidases em porção de raiz, caule, ápice e em folhas de indivíduos de Erythrina speciosa Andrews, Eugenia uniflora L., Hevea brasiliensis M. Arg., Hymenaea courbaril L. var. stilbocarpa (Hayne) Lee et Lang, Joannesia princeps Vell., Licania tomentosa (Benth.) Fritsch, Pachira aquatica Aubl. e Psidium guajava L., obteve-se comportamento pioneiro para as espécies Eugenia uniflora L., Hymenaea courbaril L. var. stilbocarpa (Hayne) Lee et Lang, Joannesia princeps Vell. e Psidium guajava L., e comportamento não-pioneiro para as espécies Erythrina speciosa Andrews, Hevea brasiliensis M. Arg., Licania tomentosa (Benth.) Fritsch e Pachira aquatica Aubl.. Dessa maneira foi possível verificar que a análise da atividade peroxidásica... (Resumo completo, clicar acesso eletrônico abaixo)

Efeito de diferentes espessuras, técnicas de aplicação e protocolos de resfriamento na resistência à fratura da cerâmica de cobertura aplicada sobre infraestrutura de y-tzp

Pós-graduação em Odontologia Restauradora - ICT

Da Campanha de Educação de Adolescentes e Adultos aos Grupos Escolares noturnos: São Carlos, SP (1930 a 1950)

Pós-graduação em Educação Escolar - FCLAR

Análise de fadiga em rodas automotivas utilizando método dos elementos finitos

The increasing search for better performance at the automotive industry, especially on the matter of fuel consumption, caused a progressive evolution of industrial technology. For the wheel this study is based on the try of reducing mass and decreasing the moment of inertia, characteristics that directly reflect on the performance parameter, as consumption and acceleration, so that it also is effective on the growth of the profit margin, since it reduces the costs of the locomotion. In this paper will be applied the Finite Element Analysis to explain the wheel behavior and identify ways to improve the performance. To the analyze it will be simulated a test condition established by ABNT NBR 6751:2009 foreseeing a possible collapse through general yielding and fatigue. The load here presented results from the equation presented on the norms and in the datas provided by the manufacturer

Estudo de tensões residuais em juntas soldadas utilizando o método dos elementos finitos

Pós-graduação em Engenharia Mecânica - FEG

Influência de diferentes superfícies de implantes unitários com geometria do tipo hexágono externo, Platform Switching e Cone-Morse em osso tipo III e IV: estudo pelo método dos elementos finitos tridimensionais

Pós-graduação em Odontologia - FOA

Análise das tensões em próteses implantossuportadas esplintadas, variando a localização dos implantes, pôntico e cantilever: estudo pelo método dos elementos finitos tridimensionais

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise comparativa de tensões e deformações específicas em uma estrutura treliçada, utilizando abordagem experimental e pelo método de elementos finitos

The process of knowledge construction is associated with physical or mechanical view of the phenomenon. In mechanical engineering courses should supplement their courses with physical or virtual learning devices to aid visualization of these phenomena. For the purpose of improving the mechanical engineering department laboratory practice was developed, through a project, a didactic device a trellis. The purpose of this work is the detailed study by comparing the theoretical results with the experimental results collected through the specific strains collected in the Catman. The study was iniatially done with nodes made of aluminum, giving results with high errors not allowing a good conclusion of results. For best results were achieved an improvement of the structure with strict we support the lattice and, thus, further study and greater quality of lattice structure

Análise estática de um guindaste de torre, utilizando o método dos elementos finitos

The finite element method is of great importance for the development and analysis of a new product being designed or already on the market, and that requires some specific request or special application. The tower crane, being an essential equipment for modern construction to increase productivity and safety on construction sites, is required for many types of special applications day after day, in many kinds of work. Paying attention to this growing need for handling special projects for the tower crane, faced with the importance and necessity of development and improvement of knowledge in more accurate and practical calculation methods such as the finite element method , for greater agility and precision in the response to a new project. The tower crane is defined by the maximum load moment that it can act with a certain amount of load. The tower crane which will be analyzed in this work , for example, is a tower crane with a resulting capacity of 85 Metric Tons which are considered basic dimensions data of a fisical tower crane of a crane company Liebherr in Guaratinguetá . Thus, the project analysis will begin with the threedimensional representation of the crane lines with AutoCAD software , conversion of this model to the format accepted ANSYS Workbench and completion of 3D modeling of structural components in Design module ANSYS software. After structural modeling is completed, the simulation is performed in static simulation of ANSYS Workbench software mode. The standards will be adopted to DIN (Deutsches Institut für Normung) and EN 14439 (Europäische Normung 14439) and some NR 's related to specific security class of tower cranes, which will be referred throughout the work

Caracterização do fator de intensidade de tensão em corpos trincados através do método dos elementos finitos

The industry generally has sought materials with high mechanical resistance, low density, thermal stability and corrosion resistance. In the aerospace industry, for example, the use of aluminum alloys, such as Al 2024-T351 and Al 7075-T7351, have become essential. However, the use of these materials often do not resulted in a satisfactory performance of the component, since the presence of cracks can cause total rupture of the component, even with a tension below the yield stress of the material, unexpectedly. In this work, these aluminum alloys were analyzed and samples were modeled by the finite element method. Moreover, in the models were applied two different types of cracks, central and edge crack, a vertical force was applied to result in a tension 70% of the yield stress of the material analyzed. Through stress asymptotic distribution in the region near the crack tip were calculated the values of the stress intensity factors for each crack length, after the stress intensity factors characterized were compared graphically with the values of fracture toughness found in the available literature

Projeto mecânico de um modelo para túnel de vento e validação de seus componentes à partir de simulações em software de elementos finitos

The objective of this study was to develop a model that allows testing in the wind tunnel at high angles of attack and validates its most critical components by analyzing the results of simulations in finite element software. During the project this structure suffered major loads identified during the flight conditions and, from these, we calculated the stresses in critical regions defined as the parts of the model that have higher failure probabilities. All aspects associated with Load methods, mesh refining and stress analysis were taken into account in this approach. The selection of the analysis software was based on project needs, seeking greater ease of modeling and simulation. We opted for the software ANSYS® since the entire project is being developed in CAD platforms enabling a friendly integration between software's modeling and analysis

Memórias subterrâneas, histórias (re) visitadas: a contribuição metodologia da história oral em estudos de grupos étnicos

This article aims to reflect on the contribution of oral history in studies involving memory and identity of ethnic groups. Problematic issues here are part of the result of two recently completed researches, which consisted of reconstructing the memory of Afro-Brazilians from the methodology of oral history. These surveys were intended to transpose, into written language, memories transmitted by oral tradition and which was confined to family circles. The first was to investigate the process of identification and transmission of knowledge from a black cultural practice in the countryside of São Paulo (Piracicaba, Capivari, and Tietê), the Batuque of Umbigada, and the second to reconstruct the stories and culture of Afro-Brazilians in the city of Itu, São Paulo.