Influence of the concentration of Sb2O3 on the electrical properties of SnO2 varistors

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Air abrasion before and/or after zirconia sintering: surface characterization, flexural strength, and resin cement bond strength

The purpose of this in vitro study was to evaluate the effect of air-abrasion/zirconia sintering order on the yttria partially stabilized tetragonal zirconia polycrystal (Y-TZP) surface characterization (roughness, morphology, and phase transformation), flexural strength (FS), and shear bond strength (SBS) to a resin cement. Y-TZP specimens were air abraded with 50-μm Al2O3 particles after (AS), before (BS), or before and after zirconia sintering (BAS). For roughness (Ra), 30 block specimens (12×12×3.0 mm; n=10) had their surfaces analyzed by a profilometer. Next, on the air-abraded surfaces of these specimens, composite resin discs (n=30) were bonded with RelyX ARC. The bonded specimens were stored for 24 hours in distilled water at 37°C before shear testing. Failure mode was determined with a stereomicroscope (20×). The surface morphology (n=2) was evaluated by SEM (500×). For the four-point flexural strength test (EMIC DL2000), 39 bar-shaped specimens (20×4.0×1.2 mm; n=13) were air abraded according to the three conditions proposed, and an additional group (nonabraded) was evaluated (n=13). The quantitative analysis of phase transformation (n=1) was completed with Rietveld refinement with X-ray diffraction data. Ra (μm) and SBS (MPa) data were analyzed by one-way analysis of variance (ANOVA) and the Tukey test (α=0.05). Pearson correlation analysis was used to determine if there was a correlation between roughness and SBS. For FS (MPa) data, one-way ANOVA and the Dunnett C-test (α=0.05) were used. The air-abrasion/zirconia sintering order influenced significantly (p<0.001) Ra, SBS, and FS. The BS and AS groups presented the highest (1.3 μm) and the lowest (0.7 μm) Ra. The highest SBS (7.0 MPa) was exhibited by the BAS group, followed by the AS group (5.4 MPa) and finally by the BS group (2.6 MPa). All groups presented 100% adhesive failure. A weak correlation (r=−0.45, p<0.05) was found between roughness and SBS. The air-abrasion/zirconia sintering order provided differences in the surface morphology. The nonabraded (926.8 MPa) and BS (816.3 MPa) groups exhibited statistically similar FS values but lower values than the AS (1249.1 MPa) and BAS (1181.4 MPa) groups, with no significant difference between them. The nonabraded, AS, BS, and BAS groups exhibited, respectively, percentages of monoclinic phase of 0.0 wt%, 12.2 wt%, 0.0 wt%, and 8.6 wt%. The rougher surface provided by the air-abrasion before zirconia sintering may have impaired the bonding with the resin cement. The morphological patterns were consistent with the surface roughness. Considering the short-term SBS and FS, the BAS group exhibited the best performance. Air abrasion, regardless of its performance order, provides tetragonal to monoclinic transformation, while sintering tends to zero the monoclinic phase content.

Agronomic efficiency and grain quality of upland rice cultivars as a function of nitrogen topdressing

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Maize leaf phytotoxicity and grain yield are affected by nitrogen source and application method

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Feeding high-moisture corn grain silage to broilers fed alternative diets and maintained at different environmental temperatures

The effects of the dietary substitution of dry corn by high-moisture corn grain silage (HMCGS) were evaluated on the performance, nutrient digestibility and serum biochemical parameters of broilers reared in an alternative production system and submitted to different environmental temperatures. A total of 288 one-day-old male Cobb chicks were distributed according to a randomized block design in a 3x4 factorial arrangement: three environmental temperatures (hot, thermoneutral or cold) and four levels of HMCGS in substitution of dry corn (0%, 20%, 40% or 60%). The acid analysis showed that the evaluated HMCGS contained average percentage values of ethanol, lactic acid, and acetic acid (expressed in 100% of dry matter) of 0.7690, 2.7320 and 0.0249%, respectively. Propionic and butyric acids were not detected. Dry corn and HMCGS presented pH values of 5.8 and 3.3, respectively. The inclusion of HMCGS reduced dietary pH, as shown by the values of 5.7, 5.4, 5.1 and 4.8 recorded for the diets containing 0%, 20%, 40% and 60% of HMCGS, respectively. There was no significant interaction between diets and environmental temperature. HMCGS may replace up to 40% dry corn in broiler diets when performance, triglyceride levels, and HDL-cholesterol ratio is considered, and up to 60% when nutrient digestibility is evaluated. High environmental temperature impairs broiler performance, nutrient digestibility, and serum biochemistry, demonstrating the influence of environmental temperature on broiler metabolism and performance.

Intake, performance and estimated methane production of Nellore steers fed soybean grain

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural, optical, and magnetic properties of NiMoO4 nanorods prepared by microwave sintering

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Influence of wood moisture content on modulus of elasticity on tension paralllel to the grain of brasilian species

Periodically, when necessary, standard documents are revised in order to analyze inconsistencies and to include considerations according new realities verified. In this sense, aiming to quantify the wood moisture content influence on modulus of elasticity, it was applied tension tests parallel to the grain for six specimens of different strength classes of wood, considering nominal moisture of 12, 20, 25, and 30% in Brazil. The present paper examine the adequacy of the current Brazilian standard ABNT NBR7190:1997, in review, about the adoption of a first degree equation to describe the influence of wood moisture content for timber structures design. It was obtained a new first degree equation which leads to statically equivalent estimations when compared with results by ABNT NBR7190:1997 equation. However, as recommendations it could be maintain the current expression for the next text of the referred document review, without prejudice to statistical significance of the estimates.

Síntese e caracterização de alvo de óxido de zinco dopado com alumínio

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Análise da resposta dielétrica e varistora de compostos cerâmicos multifásicos à base de Ca2CU2Ti4-xSnxO12 (0,0 < x< 4,0)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência dos tratamentos térmicos na microestrutura e nos micromecanismos de fratura da liga ti-6al-4v produzida por sinterização direta de metal por laser (DMLS)

Pós-graduação em Engenharia Mecânica - FEIS